GUIDE AND GAGE COMPONENTS TM - Naamsstandards
GUIDE AND GAGE COMPONENTS INDEX SERIES TM Stamping 01/29/13 PAGE DATE G-1 01/29/13 Guide and Gage Components Index G-1.1 01/29/13 Guide and Gage Components Index G-2 08/12/97 G01 & G02 Self-Lube Guide Block G-3 01/03/95 G01 Self-Lube Guide Block (45mm) Coding G-4 01/03/95 G02 Self-Lube Guide Block (60mm) Coding G-5 08/12/97 G11 Self-Lube Corner Guide Blocks G-6 05/19/00 G15 65 mm Wide U & V Blocks G-7 05/19/00 G16 & G17 65 mm Wide U & V Blocks G-8 05/19/00 G21 75 mm Wide U & V Blocks G-9 05/19/00 G22 & G23 75 mm Wide U & V Blocks G-10 06/20/03 G31 125 mm Wide U & V Blocks G-11 05/19/00 G32 & G33 125 mm Wide U & V Blocks G-12 05/19/00 G41, G42 & G43 Center Key Guide and Center Key G-13 05/19/00 G50 Shoulder Guide Post/Pin G-14 05/19/00 G50 Shoulder Guide Post/Pin Coding G-15 05/19/00 G51 Guide Post/Pin G-16 10/17/05 G51 Guide Post/Pin Coding G-17 08/04/05 G61 Guide Post/Pin Bronze Bushing G-18 08/04/05 G71 Bronze Pad Bushing G-19 05/19/00 G72 & G73 Bushing Toe Clamp G-20 05/19/00 G72 & G73 Bushing Clamping Procedures G-21 05/19/00 G81 Finger Gage G-22 09/25/07 G91 Balancing Cones G-23 05/19/00 G91 Balancing Cones Coding G-24 10/19/01 G82 Disappearing Gage G-25 09/29/03 G34 175 mm Wide U & V Blocks G-26 09/29/03 G35 & G36 175 mm Wide U & V Blocks G-27 12/19/12 1997 Auto/Steel Partnership www.naamsstandards.org DESCRIPTION Blank Page This document is Uncontrolled when printed. G-1
GUIDE AND GAGE COMPONENTS INDEX SERIES TM Stamping PAGE DATE G-28 12/19/12 Blank Page G-29 12/19/12 Blank Page G-30 12/19/12 Blank Page G-31 12/19/12 Blank Page G-32 12/19/12 Blank Page G-33 12/19/12 Blank Page G-34 01/29/13 Blank Page G-35 01/29/13 Blank Page G-36 08/01/11 G56 Blank Crowder G-37 08/01/11 G56 Blank Crowder G-38 08/01/11 Blank Page G-39 08/01/11 Blank Page G-40 08/01/11 G95 Trim Tab Pilot Gage G-41 08/01/11 G95 Trim Tab Pilot Gage G-42 08/01/11 G95 Trim Tab Pilot Gage G-43 08/01/11 G95 Trim Tab Pilot Gage G-44 08/01/11 G95 Trim Tab Pilot Gage G-45 08/01/11 G95 Trim Tab Pilot Gage G-46 12/19/12 G96 Adjustable Bar Gage/Sensor G-47 12/19/12 G96 Adjustable Bar Gage/Sensor G-48 12/19/12 G96 Adjustable Bar Gage/Sensor 1997 Auto/Steel Partnership www.naamsstandards.org 01/29/13 DESCRIPTION This document is Uncontrolled when printed. G-1.1
G L O B A L S TA N D A R D C O M P O N E N T S SELF-LUBE GUIDE BLOCKS TM (G01 & G02 SERIES) Stamping 08/12/97 H 0 13 A B 0.8 L C 12 J 0 W E 0.8 F A –A– 12 G6 (2) HOLES FOR M12 SOC. HD. SCR. (N) HOLES D 0.025 A GRAPHITE PLUGS THIS SURFACE 0.8 25 NOTES & SPECIFICATIONS: Screw hole locations 0.25 Dowel hole locations 0.10 Break all sharp edges 0.4 x 45 Material, steel. Surface harden cross-hatched areas. Evenly distributed graphite plugs to cover 20-30% of the area that requires lubrication. CODING ON FOLLOWING PAGE 1997 Auto/Steel Partnership www.naamsstandards.org This document is Uncontrolled when printed. G–2
G L O B A L S TA N D A R D C O M P O N E N T S SELF-LUBE GUIDE BLOCK CODING TM (G01 SERIES) Stamping 01/03/95 45 mm WIDE NAAMS CODE G014007 G014010 G014012 G014015 G014017 G014020 G014022 G014025 G014507 G014510 G014512 G014515 G014517 G014520 G014522 G014525 G015007 G015010 G015012 G015015 G015017 G015020 G015022 G015025 G016007 G016010 G016012 G016015 G016017 G016020 G016022 G016025 G017507 G017510 G017512 G017515 G017517 G017520 G017522 G017525 (N) HOLES 2 2 3 3 3 4 4 4 2 2 3 3 3 4 4 4 2 2 3 3 3 4 4 4 2 2 3 3 3 4 4 4 2 2 3 3 3 4 4 4 L 75 100 125 150 175 200 225 250 75 100 125 150 175 200 225 250 75 100 125 150 175 200 225 250 75 100 125 150 175 200 225 250 75 100 125 150 175 200 225 250 A – – – – – 63 73 83 – – – – – 63 73 83 – – – – – 63 73 83 – – – – – 63 73 83 – – – – – 63 73 83 B – – 50.5 63 75.5 113 128 153 – – 50.5 63 75.5 113 128 153 – – 50.5 63 75.5 113 128 153 – – 50.5 63 75.5 113 128 153 – – 50.5 63 75.5 113 128 153 C 38 63 88 113 138 163 188 213 38 63 88 113 138 163 188 213 38 63 88 113 138 163 188 213 38 63 88 113 138 163 188 213 38 63 88 113 138 163 188 213 D 51 76 101 126 151 176 201 226 51 76 101 126 151 176 201 226 51 76 101 126 151 176 201 226 51 76 101 126 151 176 201 226 51 76 101 126 151 176 201 226 E F H J 18 33 40 15 18 33 45 25 18 33 50 30 18 33 60 30 18 33 75 30 W 45 CODING CONTINUED ON FOLLOWING PAGE 1997 Auto/Steel Partnership www.naamsstandards.org This document is Uncontrolled when printed. G–3
G L O B A L S TA N D A R D C O M P O N E N T S SELF-LUBE GUIDE BLOCK CODING TM (G02 SERIES) 01/03/95 Stamping 60 mm WIDE NAAMS CODE G025007 G025010 G025012 G025015 G025017 G025020 G025022 G025025 G026007 G026010 G026012 G026015 G026017 G026020 G026022 G026025 G028007 G028010 G028012 G028015 G028017 G028020 G028022 G028025 G020007 G020010 G020012 G020015 G020017 G020020 G020022 G020025 (N) HOLES 2 2 3 3 3 4 4 4 2 2 3 3 3 4 4 4 2 2 3 3 3 4 4 4 2 2 3 3 3 4 4 4 1997 Auto/Steel Partnership L 75 100 125 150 175 200 225 250 75 100 125 150 175 200 225 250 75 100 125 150 175 200 225 250 75 100 125 150 175 200 225 250 A – – – – – 63 73 83 – – – – – 63 73 83 – – – – – 63 73 83 – – – – – 63 73 83 B – – 50.5 63 75.5 113 128 153 – – 50.5 63 75.5 113 128 153 – – 50.5 63 75.5 113 128 153 – – 50.5 63 75.5 113 128 153 www.naamsstandards.org C 38 63 88 113 138 163 188 213 38 63 88 113 138 163 188 213 38 63 88 113 138 163 188 213 38 63 88 113 138 163 188 213 D 51 76 101 126 151 176 201 226 51 76 101 126 151 176 201 226 51 76 101 126 151 176 201 226 51 76 101 126 151 176 201 226 E F H J 33 48 50 30 33 48 60 30 33 48 80 30 33 48 100 30 This document is Uncontrolled when printed. W 60 G–4
G L O B A L S TA N D A R D C O M P O N E N T S SELF-LUBE CORNER GUIDE BLOCKS TM 08/12/97 0.8 0.8 FOR M16 SOC. HD. SCR. (2) HOLES –B– Stamping H L 16 G6 (2) HOLES –A– (G11 SERIES) A D 25 B C L 10 0 0.8 20 0.025 B 0.025 A 32 A BREAK ALL SHARP EDGES 0.4 x 45 EXCEPT AS SHOWN 0 6 x 45 CHAMFER NAAMS CODE G118007 G118010 G118012 G119507 G119510 G119512 G111207 G111210 G111212 H 75 100 125 75 100 125 75 100 125 SURFACE HARDEN & GRAPHITE PLUG CROSS-HATCHED AREAS A B C D L 25 35 40 55 80 40 50 55 70 95 65 75 80 95 120 NOTES & SPECIFICATIONS: Screw hole locations 0.25 Dowel hole locations 0.10 Material, steel. Grind as shown. Evenly distributed graphite plugs to cover 20–30% of the area that requires lubrication. 1997 Auto/Steel Partnership www.naamsstandards.org This document is Uncontrolled when printed. G–5
G L O B A L S TA N D A R D C O M P O N E N T S 65 mm WIDE U & V BLOCKS TM (G15 SERIES) 05/19/00 Stamping 12 G6 & 16 C'BORE (2) HOLES STAMP DATUM "0" 0 25 50 0.8 FEMALE “U” BLOCK 20 B A C L 0 10 21 40 X 5 x 45 0.013 5R XXXXX -A- 0 120 32.5 3 x 45 FOR M12 SOC. HD. SCR. (N) HOLES 23 .025 A 65 0.8 0.026 XXX XXX 65 90 ALL CORNERS 0.05 TYPICAL SECTION "U" & "V" BLOCK ASSEMBLY FEMALE “U” BLOCK NAAMS L A B C CODE G157515 150 – 100 125 G157520 200 – 150 175 G157525 250 125 200 225 G157530 300 150 250 275 N 2 2 3 3 NOTES & SPECIFICATIONS: Material, steel Surface harden cross-hatched areas. Tolerance between screw holes 0.12 Tolerance between dowel holes 0.10 1.6 All over except where otherwise stated. Break all sharp corners. A 1997 Auto/Steel Partnership www.naamsstandards.org This document is Uncontrolled when printed. G–6
G L O B A L S TA N D A R D C O M P O N E N T S 65 mm WIDE U & V BLOCKS TM Stamping (G16 & G17 SERIES) 05/19/00 MALE “V” BLOCK GRAPHITE PLUGS THESE SURFACES ON MALE DRIVE ONLY 12 G6 (2) HOLES STAMP DATUM "0" 0 25 50 A B C L 39 5 x 45 13 0 -A- A 0.8 0 65 0.013 120 8.0 32.5 0.026 42 FOR M12 SOC. HD. SCR. (N) HOLES 90 ALL CORNERS 65 .025 A 3 x 45 0.05 TYPICAL SECTION "U" & "V" BLOCK ASSEMBLY NAAMS CODE(X) G167515 G167520 G167525 G167530 MALE “V” BLOCK NAAMS L A B CODE(Y) G177515 150 – 100 G177520 200 – 150 G177525 250 125 200 G177530 300 150 250 C N 125 175 225 275 2 2 3 3 NOTES & SPECIFICATIONS: Material, steel or bronze Use code X for steel Use code Y for bronze Surface harden cross-hatched areas on steel. Tolerance between screw holes 0.12 Tolerance between dowel holes 0.10 1.6 All over except where otherwise stated. Break all sharp corners Male “V” driver requires evenly distributed graphite plugs to cover 20-30% of the surface that requires lubrication B 1997 Auto/Steel Partnership www.naamsstandards.org This document is Uncontrolled when printed. G–7
G L O B A L S TA N D A R D C O M P O N E N T S 75 mm WIDE U & V BLOCKS TM (G21 SERIES) Stamping 05/19/00 FEMALE “U” BLOCK 0 25 50 20 B A C L 0 10 21 40 120 90 ALL CORNERS 0.026 3 x 45 FOR M12 SOC. HD. SCR. (N) HOLES 23 .025 A 65 XXX XXX 75 X 37.5 5 x 45 0.013 5R XXXXX -A- 0 0.8 STAMP DATUM "0" A 0.8 12 G6 & 16 C'BORE (2) HOLES 0.05 TYPICAL SECTION "U" & "V" BLOCK ASSEMBLY FEMALE “U” BLOCK NAAMS L A B C CODE G217515 150 – 100 125 G217520 200 – 150 175 G217525 250 125 200 225 G217530 300 150 250 275 N 2 2 3 3 NOTES & SPECIFICATIONS: Material, steel Surface harden cross-hatched areas. Tolerance between screw holes 0.12 Tolerance between dowel holes 0.10 1.6 All over except where otherwise stated. Break all sharp corners. B 1997 Auto/Steel Partnership www.naamsstandards.org This document is Uncontrolled when printed. G–8
G L O B A L S TA N D A R D C O M P O N E N T S 75 mm WIDE U & V BLOCKS TM (G22 & G23 SERIES) Stamping 05/19/00 MALE “V” BLOCK GRAPHITE PLUGS THESE SURFACES ON MALE DRIVE ONLY 12 G6 (2) HOLES STAMP DATUM "0" 0 25 50 A B C L 39 13 0 5 x 45 75 0.8 0.013 120 0.8 37.5 0.026 FOR M12 SOC. HD. SCR. (N) HOLES 90 ALL CORNERS X X X XX XX X XXXX XXX 0 42 -A- A .025 A 3 x 45 65 0.05 TYPICAL SECTION "U" & "V" BLOCK ASSEMBLY NAAMS CODE(X) G227515 G227520 G227525 G227530 MALE “V” BLOCK NAAMS L A B CODE(Y) G237515 150 – 100 G237520 200 – 150 G237525 250 125 200 G237530 300 150 250 C N 125 175 225 275 2 2 3 3 NOTES & SPECIFICATIONS: Material, steel or bronze Use code X for steel Use code Y for bronze Surface harden cross-hatched areas on steel. Tolerance between screw holes 0.12 Tolerance between dowel holes 0.10 1.6 All over except where otherwise stated. Break all sharp corners Male “V” driver requires evenly distributed graphite plugs to cover 20-30% of the surface that requires lubrication B 1997 Auto/Steel Partnership www.naamsstandards.org This document is Uncontrolled when printed. G–9
G L O B A L S TA N D A R D C O M P O N E N T S 125 mm WIDE U & V BLOCKS TM (G32 & G33 SERIES) Stamping 05/19/00 MALE “V” BLOCK STAMP DATUM "0" 0 25 50 B A C L 0.8 0.013 120 FOR M16 SOC. HD. SCR. (N) HOLES 125 16 G6 (2) HOLES 17.5 C'BORE 20 DEEP 0.8 62.5 0.026 90 ALL CORNERS 52 15 0 -A- X X XX X XXX XX X XXX XXX X XXXX XXXX 0 GRAPHITE PLUGS THESE SURFACES ON MALE DRIVE ONLY NAAMS CODE(X) G321215 G321220 G321225 G321230 0.025 A 3 x 45 5 x 45 85 MALE “V” BLOCK NAAMS L A B CODE(Y) G331215 150 – 100 G331220 200 – 150 G331225 250 125 200 G331230 300 150 250 A 57 0.05 "U" & "V" BLOCK ASSEMBLY C N 125 175 225 275 2 2 3 3 NOTES & SPECIFICATIONS: Material, steel or bronze Use code X for steel Use code Y for bronze Surface harden cross-hatched areas on steel. 1.6 Tolerance between screw holes 0.12 Tolerance between dowel holes 0.10 All over except where otherwise stated. Break all sharp corners Male “V” driver requires evenly distributed graphite plugs to cover 20–30% of the surface that requires lubrication B 1997 Auto/Steel Partnership www.naamsstandards.org This document is Uncontrolled when printed. G – 11
CENTER KEY GUIDE AND CENTER KEY G L ument is Uncontrolled when printed. G-28
Blank Page TM Stamping 12/19/12 A Data Removed. Pages Left Blank For Future Use. 1997 Auto/Steel Partnership www.naamsstandards.org This document is Uncontrolled when printed. G-29
Blank Page TM Stamping 12/19/12 B Data Removed. Pages Left Blank For Future Use. A 1997 Auto/Steel Partnership www.naamsstandards.org This document is Uncontrolled when printed. G-30
Blank Page A TM Stamping 12/19/12 B Data Removed. Pages Left Blank For Future Use. 1997 Auto/Steel Partnership www.naamsstandards.org This document is Uncontrolled when printed. G-31
Blank Page TM Stamping 12/19/12 A Data Removed. Pages Left Blank For Future Use. 1997 Auto/Steel Partnership www.naamsstandards.org This document is Uncontrolled when printed. G-32
Blank Page TM Stamping 12/19/12 B Data Removed. Pages Left Blank For Future Use. A 1997 Auto/Steel Partnership www.naamsstandards.org This document is Uncontrolled when printed. G-33
Blank Page TM Stamping 01/29/13 Data Removed. Pages Left Blank For Future Use. 1997 Auto/Steel Partnership www.naamsstandards.org This document is Uncontrolled when printed. G-34
Blank Page TM Stamping 01/29/13 Data Removed. Pages Left Blank For Future Use. 1997 Auto/Steel Partnership www.naamsstandards.org This document is Uncontrolled when printed. G-35
BLANK CROWDER (G56 SERIES) TM S tamping 08/01/11 Air cylinder may be rotated 90 C W or C C W for horizontal ports . A B 50 A 25 0.01 G 1/8" P OR T S 2 - P LAC E S 130 55 30 64 15 102 0.01 30 7.2 Ø 10 H7 DOW E LS 2-P LAC E S 15 Ø11 THROUGH 4-P LAC E S 48 A 75 H 45 15 1 6 15 (S T R OK E ) S C ODING ON F OLLOW ING PAG E 1997 Auto/S teel P artners hip T his document is Uncontrolled when printed. G -36
BLANK CROWDER TM (G56 SERIES) 1997 Auto/S teel P artners hip Stamping NAAMS C ode A B H G 5615075 G 5615100 G 5615125 G 5615150 G 5615175 G 5615200 G 5630075 G 5630100 G 5630125 G 5630150 G 5630175 G 5630200 G 5650075 G 5650100 G 5650125 G 5650150 G 5650175 G 5650200 163 163 163 163 163 163 178 178 178 178 178 178 198 198 198 198 198 198 55 55 55 55 55 55 60 60 60 60 60 60 80 80 80 80 80 80 75 100 125 150 175 200 75 100 125 150 175 200 75 100 125 150 175 200 08/01/11 S T R OK E S 15 15 15 15 15 15 30 30 30 30 30 30 50 50 50 50 50 50 T his document is Uncontrolled when printed. A G -37
(-) TM Stamping 08/01/11 PAGE LEFT BLANK FOR FUTURE USE 1997 Auto/Steel Partnership www.naamsstandards.org This document is Uncontrolled when printed. G-38
(-) TM Stamping 08/01/11 PAGE LEFT BLANK FOR FUTURE USE 1997 Auto/Steel Partnership www.naamsstandards.org This document is Uncontrolled when printed. G-39
TRIM TAB PILOT GAGE (G95 SERIES) TM Stamping 08/01/11 MATERIAL : SEE EACH DETAIL FOR MATERIAL DETAIL 1 2 3 4 5 DESCRIPTION PILOT PIN GAGE TRIM BLADE GAGE BLOCK PILOT GAGE BASE GAGE BLOCK ADJUSTMENT SCREW NAAMS CODE G95150A G95300B G95150C G95300D G95150E G95300F G95150G G95300H G95150J G95150K G95300L G95150M G95300N G95150P G95300R G95150S “H” PIN HEIGHT 136 286 136 286 NO PIN NO PIN 136 286 136 NO PIN 286 136 286 136 286 NO PIN 1 H 2 PIN DIAMETER 12.75 12.75 12.75 12.75 12.75 15.75 15.75 15.75 15.75 15.75 19.75 19.75 19.75 19.75 19.75 3 TRIM BLADE STEEL YES YES NO NO YES NO YES YES NO YES NO YES YES NO NO YES 4 30 5 CONTINUED ON FOLLOWING PAGES 1997 Auto/Steel Partnership www.naamsstandards.org This document is Uncontrolled when printed. G-40
TRIM TAB PILOT GAGE (G95 SERIES) TM Stamping 08/01/11 MATERIAL : ISO 4957 - 50CrMoV15-1 HARDEN Rc 56-58 DOUBLE TAMPER 30 2.3 R H ØA 0 Ø 20 -0.02 NAAMS CODE G9513136 G9513286 G9516136 G9516286 G9520136 G9520286 ØA 12.75 12.75 15.75 15.75 19.75 19.75 H 136 286 136 286 136 286 42 3 Ø 23 1 1997 Auto/Steel Partnership www.naamsstandards.org PILOT PIN GAGE This document is Uncontrolled when printed. G-41
TRIM TAB PILOT GAGE (G95 SERIES) TM Stamping 08/01/11 MATERIAL : ISO 4957 - 50CrMoV15-1 LEFT SOFT FINISH ASSEMBLY 90 15 60 30 75 NAAMS Code Dim. A G9513 13.0 G9516 16.0 G9520 20.0 Pilot Required 9513136 9513286 9516136 9516286 9520136 9520286 20 16 30 A 0.05 FOR M12 SOCKET HEAD SCREW 2 PLACES DRILL AND REAM FOR Ø12 DOWEL 2 PLACES MACHINE AT ASSEMBLY Ø20 57 10 Ø13.5 2 1997 Auto/Steel Partnership www.naamsstandards.org TRIM BLADE This document is Uncontrolled when printed. G-42
TRIM TAB PILOT GAGE (G95 SERIES) TM Stamping 08/01/11 MATERIAL : ISO 683/18 - C20 8 x 45 19.00 18.95 41 55 14 14 20 0 40 -0.04 0.02 Ø 20 -0 45.95 46.00 24 11.2 3 12.80 12.84 Ø 24 3 1997 Auto/Steel Partnership www.naamsstandards.org GAGE BLOCK This document is Uncontrolled when printed. G-43
TRIM TAB PILOT GAGE (G95 SERIES) TM Stamping 08/01/11 MATERIAL : ISO 683/18 - C20 DRILL AND REAM FOR Ø 12 DOWEL 2 PLACES DRILL AND REAM FOR Ø 6 DOWEL M12x1 TAP 35 DEEP 2 PLACES DRILL AND REAM FOR Ø 12 DOWEL 2 PLACES FOR M12 SOCKET HEAD SCREW 4 PLACES 67 62 32 12 100 42 44 17 13 20 30 30 40 30 30 60 60 75 150 30 Ø 20 75 60 15 30 14 Ø 13.5 4 1997 Auto/Steel Partnership www.naamsstandards.org M20x2.5 TAP THROUGH PILOT GAGE BASE This document is Uncontrolled when printed. G-44
TRIM TAB PILOT GAGE (G95 SERIES) TM Stamping 08/01/11 MATERIAL : A. ISO 683/18 - C18 - B7 THREADED ROD -OR- ISO 848-1 (min) B. ISO 683/18 - C20 B 1.5 CHAMFER (2 PLACES) M20 x 2.5 JAM NUT M20 x 2.5 THREAD 12.50 0.2 - 0.0 A 6 0.05 19.00 - 0.0 HEX SOCKET 10 x 10 DEEP 95 5 GAGE BLOCK ADJUSTMENT SCREW 1997 Auto/Steel Partnership www.naamsstandards.org This document is Uncontrolled when printed. G-45
200MM ADJUSTABLE BLANK GAGE WITH BAR SENSOR G96 SERIES TM Stamping 12/19/12 Adjustable 200mm blank gage with 130mm bar sensor. Mark with NAAMS code in 6mm high letters as shown, and manufacturers identification. Install with M10 x 30 long socket head cap screws, M10 flat washers and lock washer. (Not suppiled.) Tack weld washers to base after final adjustment. For flat binders, Bottom of sensor must be 5mm below edge of nested blank. G A or J 5 B NAAMS CODE AND MFG. IDENTIFICATION HERE SENSING RANGE C B D 120 COMMERCIAL ELECTRICAL EXTENSION CABLE H E F 5 8 70 AT MAX HEIGHT 20 AT MIN HEIGHT NAAMS CODE G960001 G960002 ITEM I.D. A B C D E F G H J QUANTITY 1 8 2 4 1 1 1 1 - 1997 Auto/Steel Partnership 8 2 4 1 1 1 1 1 NAAMS Code - G960001 - 24VDC Sensor NAAMS Code - G960002 - 120VAC Sensor DESCRIPTION OF ADJUSTABLE BLANK GAGE WITH BAR SENSOR KIT BAR SENSOR - 24VDC TURCK #BI20-CK40130-VP4X2-H1141/S1009 OR EQUIVALENT M6 FLATWASHER M6 x 0.8 LOCKNUT WITH NYLON INSERT M6 x 0.8 x 12 BUTTON HEAD CAP SCREW (BLUE) GENERIC M6 NYLON TUBING CLIP M6 x 0.8 x 8 LONG SOCKET HEAD CAP SCREW GAGE RISER BRACKET SENSOR MOUNT BRACKET BAR SENSOR - 120VAC TURCK #BI20-CK40130-ADZ30X2-B1131/S1009 OR EQUIVALENT This document is Uncontrolled when printed. G-46
200MM ADJUSTABLE BLANK GAGE WITH BAR SENSOR G96 SERIES Stamping 12/19/12 DETAIL G GAGE RISER BRACKET G960001 or G960002 M6 x 1.0 TAP THRU R5.5 TYP. R5.5 TYP. TM 10 34 60 60 10 10 80 10 35 25 44 50 37 8 8 30 6 x 25 x 44 CRS PLATE INSET 2mm HARDEN BRACES TO RC45-50/.015DP PRIOR TO WELDING 222 M6 x 1.0 TAP (8) PLACES BOTH SIDES 200 10 TYP 65 8 85 80 MATERIAL: ISO 683/18 - C20 (BLACK OXIDE FINISH) 1997 Auto/Steel Partnership This document is Uncontrolled when printed. G-47
200MM ADJUSTABLE BLANK GAGE WITH BAR SENSOR G96 SERIES TM Stamping 12/19/12 DETAIL H SENSOR MOUNT BRACKET G960001 or G960002 3 21 0.10 60 0.00 3 3 R3.25 TYP W 10 W 10 20 W 10 W 60 10 10 30.2 6.5 8.8 Material: ISO 683/18 - C20 (Black Oxide Finish) 1997 Auto/Steel Partnership This document is Uncontrolled when printed. G-48
G-12 05/19/00 G41, G42 & G43 Center Key Guide and Center Key G-13 05/19/00 G50 Shoulder Guide Post/Pin G-14 05/19/00 G50 Shoulder Guide Post/Pin Coding G-15 05/19/00 G51 Guide Post/Pin G-16 10/17/05 G51 Guide Post/Pin Coding G-17 08/04/05 G61 Guide Post/Pin Bronze Bushing G-18 08/04/05 G71 Bronze Pad Bushing G-19 05/19/00 G72 & G73 Bushing Toe .
The Sources of Variation in a Gage R&R Study Average and Range Gage R&R Analysis ANOVA Gage R&R Analysis EMP Gage R&R Analysis Comparison of Results Summary Quick Links The Data The data we will use is from the 4th edition of the Measurement Systems Analysis manual published by AIAG. In this Gage R&R study, there are three operators and ten parts.File Size: 809KBPage Count: 10
Linear Gage Gage Heads / Display Units Selection Guide G-2,3 Linear Gage LGK G-4 Linear Gage LGF G-5 . Ideal for integration into harsh environments . Attachment thread for thr
You can also use Gage R&R to determine where any weaknesses are. For example, you can use Gage R&R to figure out why different operators reported different readings. The Standard Approach to Gage R&R “You take 10 parts and have 3 operators measure each 2 times.” This approach to a Gage R&am
mag-gage.com Process Level Technology, Ltd. 281.332.6241 mag-gage.com Process Level Technology, Ltd. 281.332.6241 The Process Level Technology Mag-Gage is a proven method to measure liquid levels. The Mag-Gage is one of the safest and most economical ways to
Strain Gage Adhesives and Cements General Information and Selection Guide Because a strain gage can perform no better than the adhesive with which it is bonded to the test member, the adhesive is a vitally important component in every strain gage installation. Although there is
Bulk packaging is ideal for production inspection requirements where quantities of each gage size are needed but where there is no use for individual box packaging gage certification. The lower per-gage cost for bulk packaging is shown on page 4. In repetitive pr
Strain Gage Rosettes: Selection, Application and Data Reduction t e c H n o t e Strain Gages and Instruments tech note tn-515 For technical support, contact micro-measurements@vishay.com www.vishaymg.com 151 revision 25-mar-08 1.0 Introduction A strain gage rosette is, by definition, an arrangement of two or more closely positioned gage grids .
From table 9.1, this diameter requires a class Z gage tolerance Hence, the diameter of the no-go gage would be 1.2506 /-0.00006 in. Disadvantage –If the hole to be gaged is reamed to the low limit, say, 1.2494 in., and if the no-go gage is at the low limit, 1.24934 in, then the gage enters the hole and part passes inspection
