Kit, Bead Dispenser LineLazer IV & V, 3900, 5900, 200HS, 130HS .
Installation Kit, Bead Dispenser LineLazer IV & V, 3900, 5900, 200HS, 130HS, LL250SPS, LL250DC, LL ES1000 Airless Line Stripers 311068H EN For application of line striping materials. Not approved for use in European explosive atmosphere locations. Important Safety Instructions Read all warnings and instructions in this manual. Save these instructions. LineLazer IV & V 3900, 5900, 130HS, 200HS, ES1000 Model Series 277065 A 277064 A 277067 A 277066 A 245519 A 245516 A 24N265 A 245520 A LL250SPS & LL250DC Model Series 6-in. (152 mm) dispenser and hose 6-in. (152 mm) wind deflector kit with aluminum dispenser 12-in. (305 mm) dispenser and two hoses 12-in. (305 mm) Bead System 12-in. (305 mm) wind deflector with aluminum dispenser Glass bead system with one 6-in. (152 mm) dispenser Glass bead system with two 6-in. (152 mm) dispenser 277067 A 277066 A 245516 A 24N267 A 245520 A 24M641 A 24M838 A Glass bead system with one 6-in. (152 mm) dispenser Glass bead system with two 6-in. (152 mm) dispensers 6-in. (152 mm) dispenser and hose 6-in. (152 mm) wind deflector kit with aluminum dispenser 6-in. (152 mm) wind deflector with plastic dispenser 12-in. (305 mm) dispenser and two hoses 12-in. (305 mm) bead system 12-in. (305 mm) wind deflector with aluminum dispenser ti6587a
Bead Dispenser Kit Bead Dispenser Kit Setup 11. Route bead hose down to bead dispenser inlet. NOTE: To avoid bead stoppage in hose during use, make sure bead hose is in an arc curved downward with no kinks or high spots. NOTE: Glass bead system and paint guns can be mounted on either side of sprayer. 12. Mark on bead hose where it will connect to bead dispenser inlet. 1. Perform Pressure Relief Procedure (see sprayer manual). 13. Cut bead hose on mark and attach to bead dispenser inlet using clamp (11). Hoses must be cut as short as possible to allow good bead flow. 2. Remove pronged knob (E) and nut (F). Install screw (17), washer (18) and nut (19). 3. Bolt bead hopper frame legs (1, 3) to sprayer with four flange head cap screws (9) and lock nuts (10). 4. Place bead hopper ring (14) into holes in bead hop per legs. Additional Instructions (LLIV & V 250SPS, 250DC Units Only) 1. Before installing bead dispenser kit, remove the screw and clamp that hold recoil tube to frame. 5. Bolt bead hopper and bead hopper ring together with washers (15) and lock nuts (4) from kit bag. 6. Install bead hopper (7) on gun side on top of beads hopper frame. 7. Remove collar from mounting block of dispenser (8). Locate dispenser on gun support and reconnect collar to attach dispenser to support. 8. Move bead dispenser to desired location on rod. Loosen screw (4) and position link (3) to connect to gun trigger actuator (C). Tighten screw (4) and attach dispenser connecting rod (B) to gun trigger with bridge pin (2). ti19292a 2. Install new clamp to secure recoil tube to new mounting bracket. 9. Position spray gun and bead dispenser assembly (D) to position to be used in bead application and tighten. 10. Attach bead hose(s) (12). a. 6-inch: Attach bead hose (12) to bead hopper outlet with hose clamp (11). Plug other bead hopper outlet with cap (13) and clamp (11). b. 12-inch: Attach two bead hoses (12) to bead hopper outlets with hose clamps (11). ti19291a 3. NOTE: The orientation of the new clamp must allow room for the recoil tube. 2 311068H
Bead Dispenser Kit Bead Dispenser Kit F 4,15 14 7 E 19 11 11,13 1 3 18 12 9,10 17 A C 4 3 11 B 2 D 8 ti6588b 311068H 3
Bead Dispenser Kit Dispenser Adjustments Adjust dispenser plates up or down for desired bead flow. Typical flow rates range between 6 - 8 lb of glass beads per gallon of paint. Bead dispensers (A) are located behind paint guns. If not adjusted properly, dispensers may miss a short area at end of each paint stripe. Adjust gun cables so guns trigger at midpoint of handle bar trigger. Adjust bead dis pensers (A) so beads flow immediately when trigger is pulled. This ensures independent control to keep beads flowing after paint is turned off. Only use dry, clean beads. Any moisture or contamina tion with beads will cause poor bead flow. A window type screen can be used to remove unwanted debris before filling glass bead hopper. NOTE: To avoid bead stoppage, do not use wet beads or beads that have absorbed moisture. If bead stoppage is occurring, replace with dry beads. NOTICE Do not get beads in paint. Beads contaminating the paint supply can damage the pump. Make sure paint supply is covered during bead filling and handling. Operation Operate the striper as in normal striper operation. Refer to LineLazer Repair manual for paint spray tip recom mendations. Requires two guns and one 12 in. bead dispenser (see following page for 8 - 10 in. stripe gun orientation). ti6590a 4" 6 inch stripe (15 cm) 4 4 inch stripe (10 cm) 4" 4" 4-12 inch stripe (10-30 cm) 311068H
Bead Dispenser Kit Gun Orientation for 8 - 12 in. Stripe Operation B A C ti6591a For 8 - 10 in. stripe, adjust line width, loosen set screws at (A) and loosen gun adjuster (B). Tilt guns in for desired line width and tighten. Keep bead dispensers together and parallel to the ground. 8 - 10 in. stripe NOTE: To avoid glass beads clumping, do NOT store beads in hopper when not in use. Make sure to run beads out of system when done. 311068H 5
Bead Dispenser Kit - Parts List (LineLazer IV & V 3900, 5900, 130HS, 200HS, ES1000) Bead Dispenser Kit - Parts List (LineLazer IV & V 3900, 5900, 130HS, 200HS, ES1000) Ref. 1 2 3 5 6 7 8 7 14 11 2 Part 277065 15F581 115087 15F582 194666 194668 241437 277067 245516 13 1 9 10 11 12 13 14 15 17 18 19 6 12 1 3 11 10 15 8 9 121488 101566 101818 194682 403237 287680 100731 114988 100527 102040 Description KIT, bead system . LEG, hopper, RH (painted) . PLUG, tubing . LEG, hopper, LH (painted) . LABEL, identification . LABEL, warning . HOPPER, beads . DISPENSER ASSY KIT (includes 8, 11, 12) . 6-in. Dispenser Assy (Parts List, page 7) . 12-in. dispenser Assy (Parts List, page 8) . SCREW, cap, flng hd . NUT, lock . CLAMP, hose . HOSE, beads . CAP RING, hopper, frame WASHER SCREW, cap, hex hd WASHER, plain NUT, lock, hex Qty . Ref 1 2 1 2 2 1 1 1 4 6 3 1 1 1 2 1 1 1 Replacement Warning labels are available at no cost. 5 9 ti6592b 10 19 17 18 1 Remove cap (13) and install second hose (12) and clamp (11) for 12-inch bead dispenser 6 311068H
Bead Hopper Kit - Parts List (LL250SPS, LL250DC) Bead Hopper Kit - Parts List (LL250SPS, LL250DC) 4 3 9 10 5 2 7 1 11 4 ti19261a 6 8 9 8 5 Ref. Part Description 1 2 3 4 5 6 7 16N607 287680 241437 194668 101818 113984 403237 FRAME, bead mount, LL250, paint RING, hopper, frame HOPPER, beads LABEL, warning CLAMP, hose CLAMP, cable CAP, missing 311068H Qty . 1 1 1 2 1 1 1 Ref. Part Description 8 9 10 11 111194 101566 100731 194666 SCREW, cap flange HD NUT, lock WASHER LABEL, Linelazer, EZ bead system Qty . 4 6 2 2 Replacement Warning labels are available at no cost. 7
6-Inch Dispenser Assembly - Parts List 6-Inch Dispenser Assembly - Parts List 4 14 3 15 2 19 21 12 1 13 5 20 12 18 9 17 16 6 19 12 10 20 8 ti6593a 11 7 Ref. Part 277067 1 2 3 4 5 6 7 8 9 198379 114814 15A264 198058 15F363 117155 15F357 15F366 117576 8 Description DISPENSER ASSY KIT, beads (see item 8, Bead Dispenser Kit Parts List) . ROD, connecting . PIN, bridge . LINK, mounting, adjustable . SCREW, cap, schd, 10-24 x 3/8 . HOUSING, dispenser, 6 in. . SPRING, compression . DOOR, dispenser, 6 in. . PAD, foam, 6 in. . SCREW, machine, hex wash hd Qty. 1 1 1 1 1 2 1 1 8 Ref. 10 11 12 13 14 15 16 17 18 19 20 21 Part 198376 102598 115483 116998 101885 245679 198380 100085 100086 117275 15F367 166362 Description . CAP, end, bead dispenser . SCREW, cap, sch . NUT, lock . FITTING, hose, barb . SCREW, cap, sch . BLOCK, mounting . PLATE, slide . SCREW, thumb . WASHER . STUD, button, snap . PLATE, slide . LABEL, identification Qty. 2 2 5 1 2 2 1 4 4 3 2 1 311068H
12-Inch Dispenser Assembly - Parts List 12-Inch Dispenser Assembly - Parts List 4 14 19 3 15 2 5 13 12 1 6 12 8 16 9 18 19 17 12 ti2066a 10 7 11 Ref. Part 245516 1 2 3 4 5 6 7 8 198379 114814 15A264 198058 245799 117155 198378 116680 311068H Description DISPENSER ASSY KIT, beads (see item 8, Bead Dispenser Kit Parts List) . ROD, connecting . PIN, bridge . LINK, mounting, adjustable . SCREW, cap, socket head . HOUSING KIT, dispenser . SPRING, compression . DOOR, dispenser . PAD, foam, die-cut Qty. 1 1 1 1 1 2 1 1 Ref. 9 10 11 12 13 14 15 16 17 18 19 Part 117576 198376 102598 115483 116998 101885 245679 198380 100085 100086 117275 Description . SCREW, machine, hex washer hd . SCREW, door, hex . SCREW, cap, socket head . NUT, lock . FITTING, hose, barb . SCREW, cap, socket head . BLOCKING, mounting . PLATE, slide . SCREW, thumb . WASHER . STUD, button, snap Qty. 8 2 2 5 2 2 1 3 6 6 3 9
Graco Standard Warranty Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written recommendations. This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco. This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation. THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale. GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties. In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of Graco, or otherwise. Graco Information For the latest information about Graco products, visit www.graco.com. TO PLACE AN ORDER, contact your Graco distributor or call 1-800-690-2894 to identify the nearest distributor. All written and visual data contained in this document reflects the latest product information available at the time of publication. Graco reserves the right to make changes at any time without notice. For patent information, see www.graco.com/patents. Original instructions. This manual contains English. MM 311068 Graco Headquarters: Minneapolis International Offices: Belgium, China, Japan, Korea GRACO INC. AND SUBSIDIARIES P.O. BOX 1441 MINNEAPOLIS MN 55440-1441 USA Copyright 2012, Graco Inc. All Graco manufacturing locations are registered to ISO 9001. www.graco.com Revised June 2017
3. Bolt bead hopper frame legs (1, 3) to sprayer with four flange head cap screws (9) and lock nuts (10). 4. Place bead hopper ring (14) into holes in bead hop per legs. 5. Bolt bead hopper and bead hopper ring together with washers (15) and lock nuts (4) from kit bag. 6. Install bead hopper (7) on gun side on top of beads hopper frame. 7.
FP bead, one 7/0 bead, one FP bead, (8 beads total). 2) Slide all the beads to the end of the thread and tie a square knot to form a circle. Then pass through the nearest FP bead. 3) String one 7/0 bead, one FP bead, one 7/0 bead, one FP bead, one 7/0 bead, one FP bead, one 7/0 bead (7 beads total) and then pass through the same FP bead.
2. ULINE Sofpull Automatic Paper Towel Dispenser Instructions ULINE Sofpull Automatic Paper Towel Dispenser TOOLS NEEDED PARTS NOTE:. 3. ULINE Tape Dispenser User Guide ULINE Tape Dispenser User Guide ULINE Tape Dispenser User Guide. 4. ULINE MARSH Tape Dispenser User Guide ULINE MARSH Tape Dispenser SET-UP INSTRUCTIONS LOADING TAPE Open .
1. now pick up one bead 2. and pass the needle through the last bead of that triangle 3. pass the needle through the first bead of the next triangle 4. pick up another bead 5. and pass the needle through the last bead of that triangle 6. repeat steps 4 and 5 three more times 5.3 - through the first bead of the next triangle 5.4 add a bead
2 Valve body KIT M100201 KIT M100204 KIT M100211 KIT M100211 KIT M100218 KIT M300222 7 Intermediate cover (double diaphragm) - - - KIT M110098 KIT M110100 KIT M110101 4 Top cover KIT M110082 KIT M110086 KIT M110092 KIT M110082 KIT M110082 KIT M110082 5 Diaphragm KIT DB 16/G KIT DB 18/G KIT DB 112/G - - - 5 Viton Diaphragm KIT DB 16V/S KIT
See Technical Data in all equipment manuals. . stuck due to dried paint Repair pump. Manual 309250. Connecting rod is worn or damaged Replace connecting rod. Page 8. . 311019L, LineLazer 3400, FieldLazer S200 Airless Line Striper, Repair, English LineLazer 3400, FieldLazer S200 Airless Line Striper .
by Debra Schwartz for John Bead Corp. 7 1. Slide onto a 25mm eye pin – (1) 3mm silver plated bead, (1) 5mm antique silver spacer heishi bead, (1) 2/0 Cornealian White Star Black, (1) 5mm antique silver spacer heishi bead, (1) 3mm silver plated bead. 2. Make a simple loop at the top of the eye pin. 3. Open the 4mm jump ring.
Bead Society or Bead Bazaar. They work tirelessly to make this the best show possible. Jo Ann Patterson-Lavely RMBS Bead Bazaar Chairperson 2014 beadbazaar@rockybeads.org Rocky Mountain Bead Society – www.rockybeads.org 2014 Bead Bazaar Class Schedule Saturday, April 26 & Sunday, April 27,
Albert Woodfox is a former Black Panther who spent 45 years unjustly incarcerated in a Louisiana State Penitentiary. He was released in 2016, having served more than 43 years in VROLWDU\ FRQ¿QHPHQW WKH ORQJHVW SHULRG RI VROLWDU\ FRQ¿QHPHQW in American prison history. Kano is a British rapper, songwriter and actor. Kano is one of the pioneers of grime music and culture. In 2004, Kano released .
