2015 Mustang Heat Extractors Install - Roush Performance
2015-2017 Mustang Heat Extractors Installation Instructions P/N: 421869 (R1315-16C920) 39555 Schoolcraft Rd, Plymouth MI, 48170 800.59.ROUSH
2015-2017 Mustang Heat Extractors 2015-2017 Mustang Heat Extractors Installation Instructions P/N: 421869 (R1315-16C920) Application: 2015-2017 Ford Mustang 5.0L with Automatic/Manual Transmission Important Note: Before installing your ROUSH Performance Product(s), read through the entire installation procedure and check to make sure all items are present. Contact ROUSH Customer Service at 1-800-59-ROUSH, weekdays from 9:00 AM to 5:00 PM EST, with any questions regarding fit, missing parts or instructions that are unclear to you. INSTALLATION OF THE ROUSH HEAT EXTRACTORS ELIMINATES THE FACTORY TURN INDICATORS FROM THIS LOCATION ON 2016 MODELS. 1315-16C920IM-AB 01062017 1 800.59.ROUSH
2015-2017 Mustang Heat Extractors TABLE OF CONTENTS Packing List for 2015-2017 Mustang Heat Extractors .3 Equipment and Supplies Required.3 Limit of Liability Statement .3 Safety Precautions .3 Work Safely! .3 Installation .4 Template .7 1315-16C920IM-AB 01062017 2 800.59.ROUSH
2015-2017 Mustang Heat Extractors PACKING LIST FOR 2015-2017 MUSTANG HEAT EXTRACTORS Description Part Number Qty Description Heat Extractor Assembly — LH 1315-16C929 1 Adhesive Foam Heat Extractor Assembly — RH 1315-16C928 1 Website Instruction Sheet 96817A350 4 Washer – M3 Screw – M3 x 10 Self Tapper Part Number Qty 1315-HEFOAM 4 1315-P1INST 1 65120081 4 EQUIPMENT AND SUPPLIES REQUIRED 9 mm Socket Plastic Pry Tool 1/4" Drill Bit T10 Torx Drive Center Punch Trim Removal Tool Commercially Available Clear Coat (Motorcraft Part Number: PM-19500-6000) If you are missing any items, please call us toll free at 1-800-59-ROUSH. LIMIT OF LIABILITY STATEMENT The information contained in this publication was accurate and in effect at the time the publication was approved for printing and is subject to change without notice or liability. ROUSH Performance Products (RPP) reserves the right to revise the information presented herein or to discontinue the production of parts described at any time. SAFETY PRECAUTIONS STOP STOP CAREFULLY READ THE IMPORTANT SAFETY PRECAUTIONS and WARNINGS BEFORE PROCEEDING WITH THE INSTALLATION! Appropriate disassembly, assembly methods and procedures are essential to ensure the personal safety of the individual performing the kit installation. Improper installation due to the failure to correctly follow these instructions could cause personal injury or death. Read each step of the installation manual carefully before starting the installation. Always wear safety glasses for eye protection. Place ignition switch in the OFF position. Always apply the parking brake when working on a vehicle. Block the front and rear tire surface to prevent unexpected vehicle movement. If working with a lift, always consult vehicle manual for correct lifting specifications. Operate the engine only in well-ventilated areas to avoid exposure to carbon monoxide. Do not smoke or use flammable items near or around the fuel system. Use chemicals and cleaners in well-ventilated areas. Batteries produce explosive gases, which can cause personal injury. Therefore, do not allow flames, sparks or flammable substances to come near the battery. Keeps hands and any other objects away from the radiator fan blades. Keep yourself and your clothing away from moving parts when the engine is running. Do not wear loose clothing or jewelry that can get caught in rotating parts or scratch surface finishes. Allow the engine, cooling system, brakes and exhaust to cool before working on a vehicle. WORK SAFELY! Perform this installation on a good clean level surface for maximum safety and with the engine turned off. 1315-16C920IM-AB 01062017 3 800.59.ROUSH
2015-2017 Mustang Heat Extractors INSTALLATION The following section will guide you through the installation of the ROUSH Heat Extractors 421869 (1315-16C920). 1. Open the hood and remove the hood blanket by taking out the fifteen (15) push pins that are highlighted below with an appropriate trim removal tool. 3. Remove two (2) 9 mm nuts, release the retaining clips and remove each factory heat extractor. NOTE: ROUSH heat extractors are not compatible with turn indicators found on 2016 models. The turn indicators will need to be disconnected and wiring secured. 2. Remove the two (2) adhesive pads that retain the cables for each factory heat extractor. 4. Remove the two (2) black plastic brackets from the hood by gently prying them off with your fingers or a non-marring trim tool. Clean off any leftover adhesive once they are removed. 1315-16C920IM-AB 01062017 4 800.59.ROUSH
2015-2017 Mustang Heat Extractors 7. Install the supplied adhesive backed foam (P/N: 1315-HEFOAM-AA) to the bottom of the factory black plastic brackets as shown below. 8. Remove the two (2) studs from the factory heat extractors and install them on the ROUSH Heat Extractors. 5. Cut out the drill templates from the last page of this instruction manual, tape them in place as shown below and then mark the two (2) drill holes with a center punch. 6. Drill each hole with a 1/4" bit. After the holes are drilled, apply commercially available clear coat (Motorcraft Part Number: PM-19500-6000) to the exposed metal so that it does not corrode. 1315-16C920IM-AB 01062017 5 800.59.ROUSH
2015-2017 Mustang Heat Extractors 9. Install the ROUSH Heat Extractors by clipping them into the factory slots and installing two (2) T10 screws (P/N: 96817A350) with two (2) washers (P/N: 65120081) in the holes that were drilled in step 6. Torque the screws to 0.4 Nm. 11. Trim two (2) of the hood blanket push pins as shown below. 12. Reinstall the factory hood blanket with the fifteen (15) pins that were removed in step 1. Be sure to use the trimmed push pins from step 11 in the locations that are identified below. 10. Reinstall the factory black plastic brackets with the two (2) nuts that were removed in step 3. Torque them to 1.4 Nm. Congratulations! You have now completed the installation of your ROUSH Heat Extractors. 1315-16C920IM-AB 01062017 6 800.59.ROUSH
2015-2017 Mustang Heat Extractors TEMPLATE SCALE 101.6 mm or 4" 1315-16C920IM-AB 01062017 7 800.59.ROUSH
2015-2017 Mustang Heat Extractors 1315-16C920IM-AB 01062017 1 800.59.ROUSH 2015-2017 Mustang Heat Extractors Installation Instructions P/N: 421869 (R1315-16C920) Application: 2015-2017 Ford Mustang 5.0L with Automatic/Manual Transmission Important Note:
INDUSTRIAL WASHER EXTRACTORS PROFESSIONAL WASHER EXTRACTORS: 6 kg 7,5 kg HIGH SPIN WASHER EXTRACTORS: 6 kg 13 kg 7 kg 16 kg 10 kg 22 kg RIGID MOUNTED WASHER EXTRACTORS: 6 kg 18 kg 7 kg 22 kg 10 kg 27 kg 13 kg 35 kg PROGRAMMIN
industrial washer extractors high spin washer extractors: 6 kg 16 kg 40 kg 7 kg 22 kg 55 kg 10 kg 22 kg pro 80 kg 13 kg 33 kg 100 kg 120 kg rigid mounted washer extractors: 6 kg 18 kg . 531486_b_pub_date_28_may_2012.doc programming manual 5 introduction 2. warnings and symbols 2.1. warnings
MUSTANG SKID STEER LOADER . PARTS MANUAL . Prior to serial #5476803 . PART #000-34884 Revised January 1994 Revised September 2008 . mus . Mustang Manufacturing Company, Inc. A GEHL Company . Printed in U.S.A. -----USE ONLY GENUINE MUSTANG REPAIR PARTS . If service and repairs are needed, see your MUSTANG dealer and always insist on GENUINE MUSTANG Parts, in order to receive the highest in .
Mustang Style Power Rack - Cast Housing (Plain) Mustang Style Power Rack - Billet Housing (Blue) Mustang Style Power Rack - Billet Housing (Plain) Part No. FR40002 FR40002PLN: FR40002-B FR40002PLN-B: OEM Design Style: Ford Mustang Style with 15.5" mounts 15.5" mounts 15.5" mounts 15.5" mounts: Steering Design: Front Steer:
Midget Mustang Reference Drawing Set: 65.00 Construction drawings reduced to 11"x17" and folded in a 8-1/2" x 11" binder. No serial # and no construction manual but does include updates and the operating manual. Midget Mustang Drawing Set: 185.00 Construction drawings
1. Amp Off When this switch is in OFF position you are using only the Guitar Models, therefore . 26 Fender Mustang Neck Neck 1 27 Fender Mustang Neck Neck 2 28 Fender Mustang Mid Mid 3 29 Fender Mustang Bridge Bridge 4 30 Fender Mustang Bridge Bridge 5 . In this instruction manual the lightning within a triangle means “Electrical caution!”.
Skid-Steer Loaders Operator's Manual #917179/AP1005 Mustang Manufacturing Company, Inc. 1880 Austin Road, P.O. Box 547 . Mustang service parts. Mustang skid-steer loaders are designed and intended to be used only with Mustang attachments or approved referral attachments. Mustang Manufac-
API Structure Over 500 member companies involved in all aspects of the oil and natural gas industry Over 700 committees and task forces covering various advocacy and technical issues Staff of 240 led by board of directors who are the CEO’s of API member companies . API Standards Program All industry segments active in standardization: Exploration and Production Refining Petroleum .
