4010 Fire Alarm

4010 Fire AlarmApplications Manual574-908Rev. ATechnical Manuals Online! - http://www.tech-man.com

Copyright and TrademarksCopyright Simplex Time Recorder Co., 1999. All rights reserved.Printed in the United States of America.Information in this document is subject to change without notice. No part of thisdocument may be reproduced or transmitted in any form or by any means,electronic or mechanical, for any purpose, without the express written consent ofSimplex Time Recorder Company.Walk Test is protected by US Patent No. 4,725,818.MAPNET addressable communications is protected by US Patent No.4,796,025.IDNet is patent pending.TrueAlarm Analog Detection is protected by US Patent No. 5,155,468.TrueAlarm Detector Base is protected by US Patent No. 5,173, 683.Cautions and WarningsSYSTEM REACCEPTANCE TEST AFTER SOFTWARE CHANGES - Toensure proper system operation, this product must be tested in accordance withNFPA72-1996, Chapter 7 after any programming operation or change in sitespecific software. Reacceptance testing is required after any change, addition ordeletion of system components, or after any modification, repair or adjustmentto system hardware or wiring.All components, circuits, system operations, or software functions known to beaffected by a change must be 100% tested. In addition, to ensure that otheroperations are not inadvertently affected, at least 10% of initiating devices thatare not directly affected by the change, up to a maximum of 50 devices, mustalso be tested and proper system operation verified.READ AND SAVE THESE INSTRUCTIONS. Follow the instructions in theinstallation, operating and programming manuals. These instructions must befollowed to avoid damage to the control panel and associated equipment. FireAlarm Control Panel (FACP) operation and reliability depend upon properinstallation.DO NOT INSTALL ANY SIMPLEX PRODUCT THAT APPEARSDAMAGED. Upon unpacking your Simplex product, inspect the contents ofthe carton for shipping damage. If damage is apparent, immediately file a claimwith the carrier and notify Simplex.ELECTRICAL HAZARD - Disconnect electrical power when making anyinternal adjustments or repairs. Servicing should be performed by qualifiedSimplex Representatives.RADIO FREQUENCY ENERGY - This equipment generates, uses, and canradiate radio frequency energy and if not installed and used in accordance withthe instruction manual, may cause interference to radio communications. It hasbeen tested and found to comply with the limits for a Class A computing devicepursuant to Subpart J of Part 15 of FCC Rules, which are designed to providereasonable protection against such interference when operated in a commercialenvironment. Operation of this equipment in a residential area may causeinterference in which case the user at his own expense will be required to takewhatever measures may be required to correct the interference.Technical Manuals Online! - http://www.tech-man.com

Codes and StandardsThe 4010 is listed for the following.UL 864 Listings for Type of System: UL 864 Power-Limited Fire Alarm Control Unit. Local (formerly NFPA 72A).Requires the sounding of an alarm via listed notification appliance(s). Auxiliary (formerly NFPA 72B).Requires 4010-9809 City Circuit Module. Remote Station - protected premise (formerly NFPA 72C).Requires 4010-9809 City Circuit Module or the 4010-9810 or -9816 DACT. Proprietary - protected premise (formerly NFPA 72D).Requires 4010-9817 (with 4010-9818 or 4010-9819) or 4010-9821 NetworkInterface Modules. Central Station - protected premise (formerly NFPA 71).Requires 4010-9810 or -9816 DACT. Suppression Releasing ServiceRequires 4010-9814 Suppression Kit.UL 864 Listings for Type of Service: Automatic, Manual, Waterflow, and Sprinkler Supervisory.UL 864 Listings for Type of Signaling: Coded, Non-Coded, March-Time and DACT.DACT requires the 4010-9810 or -9816.Factory Mutual Approved Same as UL above.Local Approvals CSFMMEAContinued on next pageTechnical Manuals Online! - http://www.tech-man.com

Codes and Standards(continued)The installer should be familiar with the relevant codes listed below as well asany other applicable local codes and standards, when installing a fire alarmsystem. NFPA 72NFPA 11 NFPA 11ANFPA 12NFPA 12ANFPA 13NFPA 14NFPA 15NFPA 16 NFPA 16A NFPA 17NFPA 17ANFPA 25 NFPA 70NFPA 80NFPA 90A NFPA 90B NFPA 92ANFPA 92B NFPA 101NFPA 170NFPA 231CNFPA 1221National Fire Alarm CodeStandard for Low-Expansion Foam and Combined AgentSystemsStandard for Medium- and High-Expansion Foam SystemsStandard on Carbon Dioxide Extinguishing SystemsStandard on Halon 1301 Fire Extinguishing SystemsStandard for the Installation of Sprinkler SystemsStandard for the Installation of Standpipe and Hose SystemsStandard for Water Spray Fixed Systems for Fire ProtectionStandard for the Installation of Deluge Foam-Water Sprinklerand Foam-Water Spray SystemsStandard for the Installation of Closed-Head Foam-WaterSprinkler SystemsStandard for Dry Chemical Extinguishing SystemsStandard for Wet Chemical Extinguishing SystemsStandard for Inspection, Testing, and Maintenance ofWater-Based Fire Protection SystemsNational Electrical CodeStandard for Fire Doors and Fire WindowsStandard for the Installation of Air Conditioning andVentilation SystemsStandard for the Installation of Warm Air Heating and AirConditioning SystemsRecommended Practice for Smoke-Control SystemsGuide for Smoke Management Systems in Malls, Atria, andLarge AreasLife Safety CodeStandard for Fire Safety SymbolsStandard for Rack Storage of MaterialsStandard on the Installation, Maintenance, and Use of PublicFire Service Communication SystemsTechnical Manuals Online! - http://www.tech-man.com

Table of ContentsChapter 1. OverviewOverview. 1-1Related Documentation. 1-1In this Chapter. 1-1Before You Begin . 1-2Introduction. 1-2Custom Control Capacities . 1-2Understand the Details of the Intended Application . 1-2Understand the Built-in Functionality Provided by System Options andPoint Types . 1-2QuickAlert Class A / Class B Guidelines . 1-3Overview. 1-3Class A QuickAlert . 1-3Class B QuickAlert . 1-4Chapter 2. Selective Signaling ApplicationsOverview. 2-1In this Chapter. 2-1Selective Signaling by Floor . 2-2Overview. 2-2Step 1. Define NAC’s Device Type, Point Type, and Custom Label . 2-2Step 2. Assign Device Types, Point Types, and Custom Labels toInitiating Devices . 2-3Step 3. Add Appropriate NACs to List L6 (Off On Silence) . 2-3Step 4: Add Appropriate NACs to List L7 (Off on Reset). 2-4Step 5. Add Floor’s Initiating Devices to a User-Defined List . 2-4Step 6. Add Custom Control Equations . 2-4Selective Signaling by Area. 2-7Overview. 2-7Step 1. Define NAC’s Device Types / Point Types / Custom Labels . 2-7Step 2. Assign Device Types, Point Types, and Custom Labels toInitiating Devices . 2-8Step 3. Add Appropriate NACs to List L6 (Off On Silence) . 2-8Step 4: Add Appropriate NACs to List L7 (Off On Reset). 2-9Step 5. Add Area’s Initiating Devices to a User-Defined List . 2-9Step 6. Add Custom Control Equations . 2-9Selective Signaling by Fire Floor, Floor Above, and Floor Below. 2-12Overview. 2-12Step 1. Define NAC’s Device Types / Point Types / Custom Label. 2-12Step 2. Define Device Types, Point Types, and Custom Labels forInitiating Devices . 2-13Step 3. Add Appropriate NACs to List L6 (Off On Silence) . 2-13Step 4: Add Appropriate NACs to List L7 (Off On Reset). 2-14Step 5. Add Each Floor’s Initiating Devices to a User-Defined List . 2-14Step 6. Add NACs to User-Defined Lists . 2-14Step 7. Add Custom Control Equations . 2-14Selective Bypass of NAC/Relay Circuits. 2-17Overview. 2-17Step 1. Define Switch Attributes. 2-17vTechnical Manuals Online! - http://www.tech-man.com

Step 2.Step 3.Step 4.Step 5.Step 6.Step 7.Step 8.Define Digital Pseudo Point Attributes. 2-18Add the Floor’s Initiating Devices to a List. 2-18Change the Point Type of NACs and Door Relays. 2-18Add the NACs and Door Relays to a List . 2-18Add Appropriate NACs to List L6 (Off On Silence) . 2-18Add Appropriate NACs to List L7 (Off On Reset) . 2-19Add Custom Control Equations . 2-19Selective Activation of Single Station Devices. 2-21Introduction. 2-21Step 1. Define Device Types, Point Types, and Mode for Single StationDevices . 2-21Step 2. Add Area’s Pull Stations to a User-Defined List . 2-21Step 3. Add Custom Control Equations . 2-21Chapter 3. Suppression ReleaseOverview. 3-1In this Chapter. 3-1Default Suppression Release Applications . 3-2Suppression Release Triggered by Single Pull Station or AutomaticInitiating Device . 3-2Suppression Release Triggered by Dual Automatic Initiating Devices . 3-2Programming Default Applications . 3-3Dual Detector, Pre-Signal, and Abort Switch with No Delay. 3-5Introduction. 3-5Programming System Options, Point Types, and Lists. 3-6Programming Custom Control . 3-7Dual Detector, Pre-Signal, and Abort Switch with Delay. 3-8Introduction. 3-8Define Lists, Digital Pseudos, and Analog Pseudos . 3-9Program Custom Control Equations . 3-10Chapter 4. Additional ApplicationsOverview. 4-1In this Chapter. 4-1Pre-Signal Operation. 4-2Overview. 4-2Step 1. Define NAC’s Device Type, Point Type, and Custom Label . 4-2Step 2. Define Device Types, Point Types, and Custom Labels forInitiating Devices . 4-3Step 3. Add Initiating Devices and NACs to User-Defined Lists . 4-3Step 4. Add Appropriate NACs to List L6 (Off On Silence) . 4-3Step 5. Add Appropriate NACs to List L7 (Off On Reset) . 4-3Step 6. Add Custom Control Equations . 4-4Programming a Utility Monitoring Point. 4-6Overview. 4-6Step 1. Change the Heat Detector’s Point Type and Custom Label. 4-6Step 2. Change the AUX Relay Point’s Point Type and Custom Label. 4-6Step 3. Define a Supervisory Digital Pseudo Point. 4-6Step 4. Program Custom Control Equations . 4-6Day / Night Programming. 4-8Overview. 4-8Step 1. Program the Monitor Device’s Point Type, Device Type, andCustom Label . 4-8viTechnical Manuals Online! - http://www.tech-man.com

Step 2. Program Custom Control Equations . 4-8AHJ City Reset . 4-11Overview. 4-11Program Custom Control Equations . 4-11Elevator Recall. 4-12Overview. 4-12Step 1. Add Primary Floor Initiating Devices to a User-Defined List . 4-12Step 2. Add Alternate Floor Initiating Devices to a User-Defined List 4-12Step 3. Add Custom Labels to AUX Relays . 4-12Step 4. Add Custom Control Equations . 4-12Selective City Circuit Activation . 4-14Overview. 4-14Step 1. Create a User-Defined List of City Circuit Alarm Points . 4-14Step 2. Create Custom Control Equations. 4-14General Alarm Shutdown for Fans and Dampers . 4-15Overview. 4-15Example: Fan / Damper Shutdown for a Four Story Building. 4-15Step 1. Program Point Type and Custom Labels for Fan Relays . 4-15Step 2. Program Point Types and Custom Labels for Damper MonitorSwitches and Relays . 4-15Step 3. Custom Control Equations . 4-16Appendix A. System Options and Point TypesIntroduction. A-1In this Chapter. A-1System Options . A-2System Options . A-2Point Types . A-4Introduction. A-4AHUF . A-4AHUO. A-4AHUR . A-5ALTERN. A-5BSIGNAL . A-5DHOLDER . A-6PRIMARY . A-6QALERT. A-6SQALERT . A-6RELAY . A-6RSIGNAL . A-7RVISUAL . A-7RWATER. A-7SIGNAL. A-8SSIGNAL. A-8SUPREL. A-8SUPV . A-8SVISUAL. A-9SWATER . A-9TSIGNAL . A-9BRELAY . A-10RRELAY . A-10FIRE. A-10WATER . A-10DUCT .

The 4010 is listed for the following. UL 864 Listings for Type of System: UL 864 Power-Limi