ESFR PENDENT TECHNICAL DATA SPRINKLER VK510 (K25.2)
Page 1 of 7TECHNICAL DATAESFR PENDENTSPRINKLER VK510 (K25.2)The Viking Corporation, 210 N Industrial Park Drive, Hastings MI 49058Telephone: 269-945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.comVisit the Viking website for the latest edition of this technical data page: www.vikinggroupinc.com1. DESCRIPTIONViking Early Suppression Fast Response (ESFR) Pendent Sprinkler VK510incorporates the capability to suppress specific high-challenge fires. The additionof a larger K-Factor allows ESFR performance at lower end-head pressures thanESFR K14 sprinklers. K25.2 ESFR sprinklers can: Eliminate the use of in-rack sprinklers when protecting high-piled storage ofcertain specified materials up to specific heights.* Reduce or eliminate the need for a system fire pump. Provide flexibility when sizing system piping.Viking VK510 ESFR Pendent Sprinklers are primarily intended to protect thefollowing types of storage, which tend to produce severe-challenge fires:palletized and solid pile storage and single, double, multiple row, and portableopen rack storage (no open-top containers or solid shelves).Viking ESFR Pendent VK510 Sprinklers provide protection of most commonstorage materials, including: Encapsulated or unencapsulated Class I, II, III, and IV commodities*.TABLE 1 cULus Listed for protection of cartoned unexpanded plastic commoditiesSPRINKLERGENERALINFORMATIONand FM Approved for protection of cartoned and uncartoned unexpandedplastic commodities*.ItemDescription FM Approved for protection of exposed expanded polystyrene andSprinkler IdentificationVK510exposed expanded polyurethane commodities*.Number (SIN)In addition, some storage arrangements of rolled paper, flammable liquids,K-factor, gpm/psi½ (lpm/bar½) 25.2 (363)aerosols, and rubber tires may be protected by Viking ESFR PendentThread Size1” NPT (25mm BSPT)Sprinkler VK510.2. LISTINGS AND APPROVALScULus Listed: Category VNWH (Listed as a Specific ApplicationSprinkler OrientationPendentMaximum Working PressurePSI (bar)175 psi (12 bar)ESFR Sprinkler)FM Approved: Class 2026VdS Approved: Certificate G4040015LPCB Approved: Ref. No. 096g/01China Approval: Approved according to China GB StandardThe 10280 VK510, ESFR Pendent Sprinkler Assembly conforms to the provision of CUAP11.03/03 standard.CUAP11.03/03 approvals are provided by: FM Approvals Ltd. 1 Windsor Dials Windsor, Berkshire, UK. SL4 1 RSApproval Certificate No. issued December 20, 2010.Note: Other International approval certificates are available upon request.* Refer the Approval Chart and Commodity Selection and Design Criteria Overview for cULus Listing and FM Approval requirements that must befollowed.3. TECHNICAL DATASpecifications:Minimum Operating Pressure: Refer to NFPA 13 or FM Global Loss Prevention Data Sheets.Maximum Working Pressure: 175 psi (12 bar). Factory tested hydrostatically to 500 psi (34.5 bar).Thread size: 1” NPT for Sprinkler 12080, 25 mm BSPT for Sprinkler 12200Nominal K-factor: 25.2 U.S. (363 metric*)* Metric K-factor measurement shown is in bar. When pressure is measured in kPa, divide the metric K-factor shown by 10.0.Form No. F 100102 20.09.09 Rev 20.2Replaces Form No F 100102 Rev 20.1(Revised NFPA and FM references)
Page 2 of 7TECHNICAL DATAESFR PENDENTSPRINKLER VK510 (K25.2)The Viking Corporation, 210 N Industrial Park Drive, Hastings MI 49058Telephone: 269-945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.comVisit the Viking website for the latest edition of this technical data page: www.vikinggroupinc.comOverall Length: 3-3/16” (81 mm)Deflector Diameter: 1-3/4” (44.5 mm)Covered by one or more of the following patents: US5,829,532; US6,059,044; US6,336,509; US6,502,643; US6,868,917; AU722593; GB2336777Material Standards:Frame Casting: Brass UNS-C84400Deflector: Phosphor Bronze UNS-C51000Seat: Copper UNS-C11000 and Stainless Steel UNS-S30400Belleville Spring Sealing Assembly: Nickel Alloy, coated on both sides with PTFE TapeCompression Screw: Stainless Steel UNS-S31603Trigger and Support: Stainless Steel UNS-S31600Fusible Element Assembly: Beryllium Nickel, coated with black acrylic paint.Ordering Information: (Also refer to the current Viking price list.)Order ESFR Pendent Sprinkler VK510 by first adding the appropriate suffix for the sprinkler finish and then the appropriate suffixfor the temperature rating to sprinkler base part number.Finish Suffix: Brass ATemperature Suffix: 165 F (74 C) C, 205 F (96 C) EFor example, Sprinkler VK510 with 1” NPT threads, Brass finish, and 165 F (74 C) temperature rating Part No. 12080AC.Accessories: (Also refer to the Viking website.)Sprinkler Wrenches:A. Part No. 13635W/B (double-ended wrench - Use Side B. Side A is for use with K14.0 ESFR Pendent Sprinkler VK500)Available since 2006.Sprinkler Cabinet: Six-head capacity: Part No. 01731A (available since 1971)4. INSTALLATIONWARNINGViking sprinklers are manufactured and tested to meet rigid requirements of the approving agencies. The sprinklersare designed to be installed in accordance with recognized installation standards or FM Global Loss Prevention DataSheets. System design must be based on ESFR design guidelines described in the latest edition of the applicable FMGlobal Loss Prevention Data Sheets, the latest NFPA Standards, the latest standards of Verband der Sachversicherer(VdS), Loss Prevention Council (LPCB), the Authorities Having Jurisdiction, and also with the provisions of governmental codes, ordinances, and standards whenever applicable. Deviation from the standards or any alteration to thesprinkler after it leaves the factory including, but not limited to: painting, plating, coating, or modification, may renderthe sprinkler inoperative and will automatically nullify the approval and any guarantee made by The Viking Corporation.A. Sprinklers must be handled with care. They must be stored in a cool, dry place in their original shipping container. Neverinstall sprinklers that have been dropped or damaged in any way. Such sprinklers should be destroyed immediately.NOTE: Wet pipe systems must be provided with adequate heat.B. The sprinklers must be installed after the piping is in place to prevent mechanical damage. Before installing, be sure to have theappropriate sprinkler model and style, with the correct orifice size, temperature rating, and response characteristics.C. With the sprinkler contained in the plastic protective cap, apply a small amount of pipe-joint compound or tape to the malethreads only, while taking care not to allow a build-up of compound in the sprinkler orifice.D. Use ONLY sprinkler wrench 13635W/B (shown in Figure 1) for installing ESFR Sprinkler VK510! With the sprinklercontained in the protective cap, install the sprinkler onto the piping by applying the sprinkler wrench to the sprinklerwrench flats only, while taking care not to damage the sprinkler operating parts. DO NOT use any other type of wrench, as this could damage the unit. DO NOT use the sprinkler deflector or fusible element to start or thread the sprinkler into a fitting. DO NOT exceed 20-30 ft. lbs. of torque (hand tight plus 1 to 1-1/2 tuirns with the wrench; over-tightening may distort thesprinkler inlet with consequent leakage or impairment of the sprinkler.E. After installation, the entire sprinkler system must be tested. The test must be conducted to comply with the InstallationStandards. Make sure the sprinkler has been properly tightened. If a thread leak occurs, normally the unit must be removed,new pipe-joint compound or tape applied, and then reinstalled. This is due to the fact that when the joint seal is damaged,the sealing compound or tape is washed out of the joint. Immediately replace any damaged units, using the special sprinklerwrench only.Form No. F 100102 20.09.09 Rev 20.2
Page 3 of 7TECHNICAL DATAESFR PENDENTSPRINKLER VK510 (K25.2)The Viking Corporation, 210 N Industrial Park Drive, Hastings MI 49058Telephone: 269-945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.comVisit the Viking website for the latest edition of this technical data page: www.vikinggroupinc.comF. After installation and testing and repairing of all leaks, remove the protective caps from the sprinklers. Do NOT use anytype of tool to remove the cap. Remove the cap by hand: turn it slightly and pull it off the sprinkler. When removingcaps, use care to prevent dislodging or damaging sprinkler fusible element. THE CAPS MUST BE REMOVED FROMSPRINKLERS BEFORE PLACING THE SYSTEM IN SERVICE!5. OPERATIONDuring fire conditions, the heat-sensitive fusible element assembly disengages, releasing the seat and belleville spring assemblyto open the waterway. Water flowing through the sprinkler orifice strikes the sprinkler deflector, forming a uniform spray pattern tosuppress the fire.6. INSPECTIONS, TESTS AND MAINTENANCENOTICEThe owner is responsible for maintaining the fire protection system and devices in proper operating condition. Forminimum maintenance and inspection requirements, refer to the NFPA standard that describes care and maintenanceof sprinkler systems. In addition, the Authorities Having Jurisdiction may have additional maintenance, testing, andinspection requirements that must be followed.A. The sprinklers must be inspected on a regular basis for corrosion, mechanical damage, obstructions, paint, etc. The frequencyof inspections may vary due to corrosive atmosphere, water supplies, and activity around the device.B. Sprinklers that have been painted or mechanically damaged must be replaced immediately. Sprinklers showing signs of corrosionshall be tested and/or replaced immediately as required. Installation standards require sprinklers to be tested and, if necessary,replaced after a specified term of service. For Viking ESFR Pendent Sprinklers, refer to the Installation Standards (e.g., NFPA 25)and the Authorities Having Jurisdiction for the specified period of time after which testing and/or replacement is required. Sprinklersthat have operated cannot be reassembled or reused, but must be replaced. When replacing sprinklers, use only new sprinklers.C. The sprinkler discharge pattern is critical for proper fire protection. Therefore, nothing should be hung from, attached to, orotherwise obstruct the discharge pattern. All obstructions must be immediately removed or, if necessary, additional sprinklersinstalled.D. When replacing existing sprinklers, the system must be removed from service. Refer to the appropriate system description and/or valve instructions. Prior to removing the system from service, notify all Authorities Having Jurisdiction. Consideration shouldbe given to employment of a fire patrol in the affected area.1. Remove the system from service, drain all water, and relieve all pressure on the piping.2. Using the special sprinkler wrench, remove the old sprinkler and install the new unit. Care must be taken to ensure thatthe replacement sprinkler is the proper model and style, with the correct orifice size, temperature rating, and responsecharacteristics. A fully stocked spare sprinkler cabinet should be provided for this purpose.3. Place the system back in service and secure all valves. Check the replaced sprinklers and repair all leaks.E. Sprinkler systems that have been subject to a fire must be returned to service as soon as possible. The entire system mustbe inspected for damage and repaired or replaced as necessary. Sprinklers that have been exposed to corrosive products ofcombustion, but have not operated, should be replaced. Refer to the Authorities Having Jurisdiction for minimum replacementrequirements.7. AVAILABILITYThe Viking Model VK510 Sprinkler is available through a network of domestic and international distributors. See The VikingCorporation web site for the closest distributor or contact The Viking Corporation.8. GUARANTEEFor details of warranty, refer to Viking’s current list price schedule or contact Viking directly.Form No. F 100102 20.09.09 Rev 20.2
Page 4 of 7ESFR PENDENTSPRINKLER VK510 (K25.2)TECHNICAL DATAThe Viking Corporation, 210 N Industrial Park Drive, Hastings MI 49058Telephone: 269-945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.comVisit the Viking website for the latest edition of this technical data page: www.vikinggroupinc.comAVAILABLE SPRINKLER TEMPERATURE RATINGS AND FINISHESSprinkler TemperatureClassificationSprinkler NominalTemperature Rating1Maximum AmbientCeiling Temperature2Frame Paint ColorOrdinary165 F (74 C)100 F (38 C)NoneIntermediate205 F (96 C)150 F (65 C)WhiteSprinkler Finish: BrassFootnotes1The sprinkler temperature rating is stamped on the deflector.2Based on NFPA-13. Other limits may apply, depending on fire loading, sprinkler location, and other requirements of the Authority Having Jurisdiction.Refer to specific installation standards.1-9/16”(40 mm)Wrench FlatProtectiveSprinkler Cap3-3/16”(81 mm)1-5/8”(42 mm)Use Side B forESFR PendentK25.2 SprinklerVK510Figure 1:ESFR Pendent Sprinkler WrenchForm No. F 100102 20.09.09 Rev 20.2Dimensions areapproximate.1-3/4”(45 mm)Figure 2:ESFR Pendent Sprinkler VK510 Dimensions
Page 5 of 7ESFR PENDENTSPRINKLER VK510 (K25.2)TECHNICAL DATAThe Viking Corporation, 210 N Industrial Park Drive, Hastings MI 49058Telephone: 269-945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.comVisit the Viking website for the latest edition of this technical data page: www.vikinggroupinc.comApproval ChartESFR Pendent Sprinkler VK510Maximum 175 PSI (12 bar) WWPBase PartNumber1SIN12080VK51012200203738Thread SizeNominalK-FactorListings and Approvals3,4,7Overall Length(Refer also to Tables 2 & PCBFM25.23633-3/1681A1See Footnote 6.A1A1A1VK510 25 mm BSPT25.23633-3/1681A1See Footnote 6.A1A1A1--VK510 25 mm BSPT25.23633-3/1681B1------B1B11” NPTApproved Temperature RatingsA - 1
threads only, while taking care not to allow a build-up of compound in the sprinkler orifice. D. Use ONLY sprinkler wrench 13635W/B (shown in Figure 1) for installing ESFR Sprinkler VK510! With the sprinkler contained in the protective cap, install the sprinkler onto the piping by applying the sprinkler wrench to the sprinkler
Antifreeze Solutions in Home Fire Sprinkler Systems 100138.04.000 May 28, 2010 CODE CONSULTANTS, INC. Page 1 Executive Summary NFPA 13, Standard for the Installation of Sprinkler Systems, has included guidance on the use of antifreeze solutions in fire sprinkler systems since the 1940 edition.1 Antifreeze solutions may be used in fire sprinkler systems where the piping system, or File Size: 942KBPage Count: 100Explore furtherNFPA 13: Standard for the Installation of Sprinkler .archive.orgNFPA 13: Standard for the Installation of Sprinkler Systemswww.nfpa.orgNFPA 13-2010: Installation of Sprinkler Systems (The .rtmconsultants.comNFPA 13 Standard For The Installation Of Sprinkler Systems .nfpa13.engineeringdesignresources. NFPA 13-2019: Installation of Sprinkler Systems Standard .blog.ansi.orgRecommended to you b
FM: 45 ft. (13,7 m) with ceilings up to 50 ft. (15,2 m)* Reduce or eliminate the need for a system fire pump. Provide flexibility when sizing system piping. Viking VK506 ESFR Pendent Sprinklers are primarily intended to protect the fol-lowing types of storage, which tend to produce severe-challenge fires: palletized
2016 ed.) and Chapter 24 (2019 ed.) of NFPA 13. Additional design criteria for the Model N252EC sprinkler may be found in FM Global Property Loss Prevention Data Sheet 8-9. The Model N252EC sprinkler is described as a quick-response K25.2EC pendent storage sprinkler in FM Global Data Sheet 8-9. Bulletin 008 June 2022 Page 4 of 5 www .
1. An automatic sprinkler system for a Small House is an improvised sprinkler system which mainly comprises sprinkler heads, sprinkler pipes, a set of sprinkler control valves, a sprinkler pump and a sprinkler tank. 2. For the design and main components of an automatic sprinkler system, reference shall be made to the attached Schematic Drawing for
sprinkler systems Use of this sprinkler is especially advantageous as a means of eliminating the use of in-rack sprinklers when protecting rack storage arrangements Operates at lower pressure than ESFR-1 ES F R 17 Pendent K FACTOR K 25.2 (362,9) THREAD SIZE 1" NPT or ISO 7-R1 SPRINKLER FINISH Natural Brass SIN TY9226 TECH DATA T FP312
CPVC Pipe 20mm CPVC Fire Sprinkler Pipe [4.5M Length] 3/4" 555 15 25mm CPVC Fire Sprinkler Pipe [4.5M Length] 1" 448 8 32mm CPVC Fire Sprinkler Pipe [4.5M Length] 1 1/4" 300 6 40mm CPVC Fire Sprinkler Pipe [4.5M Length] 1 1/2" 250 5 50mm CPVC Fire Sprinkler Pipe [4.5M Length] 2" 165 3 65mm CPVC Fire Sprinkler Pipe [4.5M Length] 2 1/2 .
performance from your sprinkler system. This has benefits for firefighting and is likely to lead to better fire outcomes. Figure 2 - Typical sprinkler system components Full or partial sprinkler system temporarily disabled Sprinkler systems are usually disabled for maintenance, or during non-sprinkler-related construction in the building.
the methods described in ASTM-C181 [4] and ISO 1927-3 [5]. From these results, the WI (based on the four first rams, calculated in Eq. (1) ), the extended WI (based on all 100 rams, calcu- lated in Eq. (2)) and changes in height and changes in density per ram as reported by the auto- mated sand-rammer. The density calculation is based on the .
