M GeneRal InfoRmaTIon E CH Bt (BlUe-tiP) Screw Bolt .

General InformationMechanical AnchorsGeneral InformationSECTION CONTENTSBT (BLUE-TIP)General InformationScrew BoltProDUCT DESCRIPTIONThe Blue-Tip is a heavy duty screw anchor with a finished hex head. The one piece designmakes it easy to install and the preferred choice for fast, reliable anchoring and is also fullyremovable. This anchor is designed to resist structural and non-structural loading in crackedand uncracked concrete.Installation InformationDesign InformationMaterial InformationOrdering InformationASSEMBLYHex HeadWithFormedWasherGENERAL APPLICATIONS AND USESScrewWithDualThreadFEATURES AND BENEFITS Consistent performance in high and low strength concreteNominal drill bit size is same as anchor denominationQuick and easy installation with a powered impact wrenchSpecial dust relief threadApproved for two embedment depthsApprovalS AND LISTINGSETAG 001 Option 1F120Taper TipVERSIONSHex HeadCarbon Steel, Zinc PlatedStainless Steel (No ETA Approval)Mechanically Galvanized(No ETA Approval)APPROVALS ETA-12/0607Loading ConditionsSTATICQUASI-STATICSuitable Base MaterialsTECH MANUAL – Mechanical Anchors 2013 dewalt PRINTED 6/13DEWALT DESIGN ASSISTReal-Time Anchor Design /anchors

Installation InformationInstallation DataNotationUnitAnchor diameterdNominal drill bit f[mm]121419Nominal embedment depth 1Nominal embedment depth 2hnom,1hnom,2[mm][mm]5575708580110Effective embedment depth 1Effective embedment depth 2hef,1hef,2[mm][mm]405751645783Drill hole depth for hef,1Drill hole depth for [mm]105115125125145165Minimum spacingsmin[mm]6090110Minimum edge distancecmin[mm]6090110Torque wrench socket sizeSw[mm]171923Diameter of hole clearance in fixtureMinimum member thickness for hef,1Minimum member thickness for hef,2hminMechanical AnchorsInstallation Informationtfixh1d0hnomLdfSw1.) Using the proper drillbit size, drill a hole intothe base material tothe required depth.2.) Remove dust and debrisfrom the hole using a handpump or compressed air.For complete installation instructions, see technical approval.www.DEWALT.com/anchors3.) Select impact wrench andmount the screw anchorhead into the hex socket.4.) Drive the anchor throughthe fixture into the holeat least to the minimumrequired embedmentdepth and until the headof the anchor comes intocontact with the fixture.TECH MANUAL – Mechanical Anchors 2013 DeWalt PRINTED 6/13Installation Instructions51

Design informationMechanical AnchorsDesign informationTension LOAD CAPACITIES - Parameters for calculation of design strengthAccording to ETAG 001 Annex C Method A.NotationUnitBTBT10BT12BT1656.078.5140.4Steel failureCharacteristic resistanceNRk,s[kN]Partial safety factorgMs[-]1.4Pullout failureCracked concreteCharacteristic resistance (hef,1)NRk,p[kN]34Characteristic resistance (hef,2)NRk,p[kN]6Partial safety factorgMp1)[-]NRk,p[kN]7.5Characteristic resistance (hef,2)NRk,p[kN]12Partial safety cc[-]1.3652.12)7.5121.83)Uncracked concreteCharacteristic resistance (hef,1)12162.12)16251.83)Increasing factor for concrete strengthConcrete failureConcrete cone failureCharacteristic spacing (hef,1)scr,N,1[mm]120154172Characteristic spacing (hef,2)scr,N,2[mm]171192248Characteristic edge distance (hef,1)ccr,N,1[mm]607786Characteristic edge distance (hef,2)ccr,N,2[mm]86Partial safety factorgMc1)[-]scr,sp,1[mm]120154172Characteristic spacing (hef,2)scr,sp,2[mm]171192248Characteristic edge distance (hef,1)ccr,sp,1[mm]607786Characteristic edge distance (hef,2)ccr,sp,2[mm]86Partial safety 0cc[-]1.36962.12)1241.83)Splitting failureCharacteristic spacing (hef,1)962.12)Increasing factor for concrete strengthTECH MANUAL – Mechanical Anchors 2013 dewalt PRINTED 6/13521) In absence of other national regulations2) The partial safety factor g2 1.4 is included3) The partial safety factor g2 1.2 is includedDEWALT DESIGN ASSISTThe DeWALT Design Assist is a powerful anchor design software which helps you to design simple and complex anchorages.The design data of all DeWALT anchor products is readily available. To download this software for free, go to 41.83)

Design informationMechanical AnchorsSHEAR LOAD CAPACITIES - Parameters for calculation of design strengthAccording to ETAG 001 Annex C Method A.NotationBTUnitBT10BT12BT1627.035.855.1Steel failureSteel failure without lever armCharacteristic resistanceVRk,sPartial safety factorg[kN][-]1)Ms1.5Steel failure with lever arm (bending)Characteristic resistanceM0Rk,sPartial safety factorg[Nm]77128[-]1)Ms3061.5Concrete failurePry-out failureFactor in equation (5.6) of ETAG 001 Annex C for hef,1k1[-]111222k2[-]gMc1)[-]Effective length of anchor for hef,1lf,1[mm]40.051.457.2Effective length of anchor for hef,2lf,2[mm]57.064.182.7Outside diameter of anchordnom[mm]101216Partial safety factorgMc1)Factor in equation (5.6) of ETAG 001 Annex C for hef,2Partial safety factor1.5Edge failure2)[-]1.51) In absence of other national regulations2) The partial safety factor g2 1.0 is includedPrecalculated Tension and shear capacitiesAccording to ETAG 001 Annex C Method A. The following tables are meant to give the designer aid in the preliminary design process. No responsibility is taken for thecorrectness of these data. The given values are valid for normal concrete C20/25 and static/quasi-static loads with the exact dimensional informationgiven. For any other conditions, the use of DDA is recommended. The values in the tables below are design level loads. This assumes a safety factor is included both on the loadingand the resistance. For cracked concrete, splitting failure is not considered assuming that a reinforcement is present which limits the crackwidth to 0.3 mm. For further details and background information please see the introduction of this manual.BT10NFchAnchoring located far from any edgeVsAnchoring located close to an edgeC20/25Embedment depthhef [mm]40.0Member thicknessh [mm]105Edge distancec [mm]-----6060606060Anchor spacings [mm]-6012060120-6012060120NRd [kN]1.42.92.95.75.71.42.92.95.75.7FRd45 [kN]2.03.73.96.87.91.83.23.44.75.3VRd [kN]6.19.112.113.724.34.15.56.95.56.9NRd [kN]3.67.17.113.714.33.67.17.113.714.3FRd45 [kN]4.37.88.513.517.13.86.37.08.49.8VRd [kN]8.512.817.019.134.05.87.79.77.79.7 - Steel strengths controls - Concrete strength controls - Anchor pullout strength controlsDEWALT DESIGN ASSISTThe DeWALT Design Assist is a powerful anchor design software which helps you to design simple and complex anchorages.The design data of all DeWALT anchor products is readily available. To download this software for free, go to CH MANUAL – Mechanical Anchors 2013 DeWalt PRINTED 6/13Embedment Depth 153

Design informationMechanical AnchorsBT10Anchoring located far from any edgeAnchoring located close to an edgeC20/25Embedment Depth 2Embedment depthhef [mm]Member thicknessh [mm]Edge distancec [mm]Anchor spacing57.0115-----6060606060s [mm]-6017160171-6017160171NRd [kN]2.95.75.711.411.42.95.75.710.911.4FRd45 [kN]3.86.97.612.115.22.94.95.86.48.3VRd [kN]10.314.020.718.841.34.45.88.55.88.5NRd [kN]5.711.411.418.822.95.710.811.415.322.9FRd45 [kN]7.012.213.918.727.85.07.99.99.113.4VRd [kN]14.519.528.926.457.86.28.212.08.212.0 - Steel strengths controls - Concrete strength controls - Anchor pullout strength controlsBT12Anchoring located far from any edgeAnchoring located close to an edgeC20/25Embedment Depth 1Embedment depthhef [mm]51.0Member thicknessh [mm]125Edge distancec [mm]-----9090909090Anchor spacings [mm]-9015390153-9015390153NRd [kN]1.93.83.87.67.61.93.83.87.67.6FRd45 [kN]VRd 34.77.39.711.49.711.4NRd [kN]5.711.411.421.922.95.711.411.421.922.9FRd45 [kN]6.612.213.221.726.46.210.611.414.316.1VRd [kN]12.219.424.430.748.610.313.716.113.716.1 - Steel strengths controls - Concrete strength controls - Anchor pullout strength controlsBT12Anchoring located far from any edgeAnchoring located close to an edgeC20/25Embedment Depth 2TECH MANUAL – Mechanical Anchors 2013 dewalt PRINTED 6/1354Embedment depthhef [mm]64.1Member thicknessh [mm]125Edge distancec [mm]-----90.090909090Anchor spacings [mm]-9019290192-9019290192NRd [kN]2.44.84.89.59.52.44.84.89.59.5FRd45 [kN]3.46.76.713.513.53.15.55.98.39.313.0VRd [kN]23.935.947.752.795.57.610.113.010.1NRd [kN]7.615.215.226.430.57.615.215.224.930.5FRd45 [kN]9.819.619.633.039.27.612.514.115.419.4VRd [kN]23.947.747.773.895.510.714.318.314.318.3 - Steel strengths controls - Concrete strength controls - Anchor pullout strength controlsDEWALT DESIGN ASSISTThe DeWALT Design Assist is a powerful anchor design software which helps you to design simple and complex anchorages.The design data of all DeWALT anchor products is readily available. To download this software for free, go to www.dewaltdesignassist.comwww.DEWALT.com/anchors

Anchoring located far from any edgeBT16Anchoring located close to an edgeC20/25Embedment Depth 1Embedment depthhef [mm]Member thicknessh [mm]Edge distancec [mm]Anchor spacing57.2145-----110110110110110s [mm]-110171110171-110171110171NRd [kN]4.28.38.316.716.74.28.38.316.716.7FRd45 [kN]5.911.411.821.823.65.08.79.112.513.4VRd [kN]20.834.141.555.983.19.913.115.013.115.0NRd .313.918.621.118.621.1FRd45 [kN]VRd [kN]Mechanical Anchorsmaterial Information - Steel strengths controls - Concrete strength controls - Anchor pullout strength controlsAnchoring located far from any edgeBT16Anchoring located close to an edgeC20/25Embedment Depth 2Embedment depthhef [mm]83.0Member thicknessh [mm]165Edge distancec [mm]-----110110110110110Anchor spacings [mm]-110248110248-110248110248NRd 111.215.019.715.019.7FRd45 [kN]VRd [kN]NRd [kN]13.927.827.844.155.613.927.727.840.855.6FRd45 [kN]17.134.234.252.868.412.620.423.623.631.5VRd [kN]36.773.373.5105.9146.915.921.127.821.127.8 - Steel strengths controls - Concrete strength controls - Anchor pullout strength controlsDEWALT DESIGN ASSISTThe DeWALT Design Assist is a powerful anchor design software which helps you to design simple and complex anchorages.The design data of all DeWALT anchor products is readily available. To download this software for free, go to www.dewaltdesignassist.commaterial Informationmaterial specificationPart no.DesignationMaterialProtection1Screw boltSpecial hardened C-steelZinc plated 5 µmwww.DEWALT.com/anchorsTECH MANUAL – Mechanical Anchors 2013 DeWalt PRINTED 6/13155