TNC 640 HSCI - Heidenhain.ca
TNC 640 HSCIFor Gen 3 DrivesThe Contouring Control forMilling Machines, Milling-TurningMachines, and MachiningCentersInformation for theMachine Tool Builder06/2020
TNC contouring control with drive system from HEIDENHAINGeneral informationTNC 640 Contouring control for milling machines, milling-turningmachines, and machining centers Axes: up to 24 control loops (22 control loops with functionalsafety (FS)), of which up to 4 can be configured as spindles For operation with HEIDENHAIN inverter systems and ideallyHEIDENHAIN motors Uniformly digital with HSCI interface and EnDat interface Version with touchscreen for multitouch operation Solid state disk (SSDR) Programming in HEIDENHAIN Klartext or G-code (ISO) Comprehensive cycle package for milling and turning operations Constant surface speed for turning operations Tool radius compensation Touch probe cycles Free contour programming (FK) Special function for fast 3-D machining Short block processing time (0.5 ms)System testControls, power modules, motors, and encoders fromHEIDENHAIN are usually integrated as components into completesystems. In such cases, comprehensive testing of the completesystem is required, irrespective of the specifications of theindividual devices.Parts subject towearControls from HEIDENHAIN contain parts subject to wear, such asa backup battery and fan.StandardsStandards (ISO, EN, etc.) apply only where explicitly stated in thebrochure.NoteIntel, Intel Xeon, Core, and Celeron are registered trademarks ofIntel Corporation.ValidityThe features and specifications described here apply to thefollowing control and NC software versions:TNC 640 with NC software versions340590-10 (export license required)340591-10 (no export license required)This brochure supersedes all previous editions, which therebybecome invalid. Subject to change without notice.RequirementsSome of these specifications require particular machineconfigurations. Please also note that, for some functions, a specialPLC program must be created by the manufacturer.Functional safety(FS)If no explicit distinction is made between standard and FScomponents (FS functional safety), then the data and otherinformation apply to both versions (e.g., TE 360, TE 360 FS).Use of thisbrochureThe purpose of this brochure is to help you select suitablecomponents from HEIDENHAIN. Further documents are requiredfor project planning (see "Technical documentation", Page 106).2
ContentsTNC contouring control with drive system from HEIDENHAIN2Overview tables4HSCI control components16Accessories26Cable overview41Technical description45Data transfer and communication80Mounting information84Overall dimensions86General information106Other HEIDENHAIN controls108Subject index109Please refer to the page references in the tables with thespecifications.3
Overview tablesComponentsControl systems15-inch design19-inch design24-inch designPageFor operating panelMC 8512(1024 x 1280 pixels)MC 8532(1280 x 1024 pixels)MC 366(1920 x 1080 pixels)16For electrical cabinet–MC 306MC 85x2; MC 306SSDR solid-state disk18NC software licenseOn SIK component18Monitor–BF 860(1280 x 1024 pixels)BF 360(1920 x 1024 pixels)Keyboard–TE 745TE 360Machine operating panelMB 721Integrated in TE 745Integrated in TE 360Main computerStorage mediumPLC inputs/outputs1)With HSCI interface2222PLB 600x (HSCI adapter for OEM machine operating panel)26PL 6000 consisting of PLB 62xx basic module (system PL) or PLB 61xx(expansion PL) and I/O modules24On UECOn UMCAdditional modules1)CMA-H for analog axes/spindles in the HSCI system27Modules for fieldbus systemsInvertersystems2)Compact inverters and modular invertersConnecting cables1)2)41May be necessary depending on the configurationFor more information, refer to the Gen 3 Drives brochure.Please note: The MC main computer does not have any PLC inputs/outputs. Therefore one PL 6000, UEC, or UMC is necessary foreach control. They feature safety-relevant inputs/outputs as well as the connections for touch probes.4
AccessoriesAccessoryTNC 640Electronic handwheelsWorkpiece touch probes1)Tool touch probes1) HR 510 FS portable handwheel, or HR 520 FS portable handwheel with display, or HR 550 FS portable wireless handwheel with display, or HR 130 panel-mounted handwheel TS 260 touch trigger probe with cable connection, or TS 460 touch trigger probe with radio and infrared transmission, or TS 740 touch trigger probe with infrared transmission TT 160 touch trigger probe with cable connection, or TT 460 touch trigger probe with radio and infrared transmissionPage28Programming station2)Control software for PCs for programming, archiving, and training Single-station license with original control keyboard Single-station license with virtual keyboard Network license with virtual keyboard Demo version with virtual keyboard or PC keyboard—free of chargeAuxiliary axis controlPNC 61033Industrial PCITC 860: additional operating station and integrated screen keyboardIPC 306: industrial PC for WindowsIPC 6490/IPC 8420 – industrial PC for PNC 61031Camera systemVS 101 camera system for monitoring the working space36Snap-on keysFor controls and handwheels371)2)For more information, refer to the Touch Probes brochureFor more information, refer to the Programming Station for TNC Controls brochureAccessories / SoftwareTNC 640PagePLCdesign1)PLC development software76KinematicsDesign1)Software for creation of kinematic models68M3D converter4)Software for creation of high-resolution collision objects in M3D format68TNCremo2),Data transfer software (TNCremoPlus with “live” screen)81ConfigDesign1)Software for configuring the machine parameters72CycleDesign1)Software for creating cycle structures79TNCkeygen1)Software for enabling SIK options for a limited time, and for single-day access to theOEM area18TNCscope1)Software for data recording73TNCopt1)Software for putting digital control loops into service73IOconfig1)Software for configuring PLC I/O and fieldbus components25TeleService1)3)Software for remote diagnostics, monitoring, and operation74RemoTools SDK1)Function library for developing customized applications for communication withHEIDENHAIN controls82virtualTNC1)3)Control component for virtual machines82TNCtest1)Software for creation and execution of an acceptance test74TNCanalyzer1)Software for the analysis and evaluation of service files741)2)3)4)TNCremoPlus2)Available to registered customers for download from the InternetAvailable to all customers (without registration) for download from the InternetSoftware release module requiredIncluded in the KinematicsDesign installation package with version 3.1 or later (software release module required)5
SpecificationsSpecificationsTNC 640PageAxesMax. of 24 control loops (22 control loops with functional safety (FS)), of whichup to 4 can be configured as spindles51Rotary axesMax. 3Synchronized axes PLC axes Main spindlesMilling: max. 4; second, third, and fourth spindle can be controlled alternatelywith the firstTurning: max. 2Milling spindle or lathe spindle activated via NC command57SpeedMax. 60 000 rpm (with software option 49, max. 120 000 rpm)*)57Operating mode switchover 57Position-controlled spindle 57Oriented spindle stop 57Gear shifting 57NC program memory 18 GB (with 32 GB SSDR) 189 GB (with 240 GB SSDR)1651Input resolution and display stepLinear axesDown to 0.01 µmRotary axesDown to 0.000 01 Functional safety (FS)With FS components, SPLC, and SKERNFor applications with up to47 SIL 2 as per EN 61508 Category 3, PL d as per EN ISO 13849-1: 2008InterpolationStraight lineIn 4 axes; in max. 6 axes with software option 9CircularIn 2 axes; in 3 axes with software option 8Helical 59Axis feedback controlWith following error With feedforward Axis clamping Maximum feed rate5160000 rpmNo. of motor pole pairsat fPWM 5000 Hz*)6For motors with a single pole pair.51Screw pitch [mm]
SpecificationsTNC 640PageCycle times of main computerMC60Block processing0.5 ms61Cycle times of controller unitCC/UEC/UMC60Path interpolation3 ms60Fine interpolationSingle-speed: 0.2 msDouble-speed: 0.1 ms (software option 49)Position controllerSingle-speed: 0.2 msDouble-speed: 0.1 ms (software option 49)Speed controllerSingle-speed: 0.2 msDouble-speed: 0.1 ms (software option 49)Current controllerfPWM3333 Hz4000 Hz5000 Hz6666 Hz with software option 498 000 Hz with software option 4910 000 Hz with software option 4913 300 Hz with software option 4916 000 Hz with software option 49Permissible temperature rangeOperation:In electrical cabinet: 5 C to 40 CIn operating panel: 0 C to 50 CStorage: –20 C to 60 CTINT150 µs125 µs100 µs75 µs with software option 4962.5 µs with software option 4950 µs with software option 4937.5 µs with software option 4930 µs with software option 497
Interfacing to the machineInterfacing to the machineTNC 640PageError compensation 69Linear axis error 69Nonlinear axis error 69Backlash 69Reversal spikes during circularmovement 69Hysteresis 69Thermal expansion 69Static friction 69Sliding friction 69Integrated PLC 75Program formatStatement list75Program input at the control 75Program input via PC 75Symbolic PLC-NC interface 75PLC memory 1 GB (with 32 GB SSDR) 4 GB (with 240 GB SSDR)75PLC cycle time9 ms to 30 ms (adjustable)75PLC inputs/outputsFor the maximum configuration of the PLC system, see Page 4624PLC inputs, DC 24 VVia PL, UEC, UMC24PLC outputs, DC 24 VVia PL, UEC, UMC24Analog inputs 10 VVia PL24Inputs for PT 100 thermistorsVia PL24Analog outputs 10 VVia PL24PLC functions 75Small PLC window 76PLC soft keys 76PLC positioning 76PLC basic program 78Integration of applications77High-level language programming Use of the Python programming language in conjunction with the PLC(software option 46)77User interfaces can be customdesigned8Creation of individualized user interfaces by the machine manufacturer with the77Python programming language. Programs up to a memory limit of 10 MB are enabledin standard mode. More can be enabled via software option 46.
Interfacing to the machineTNC 640Page72Commissioning anddiagnostic aidsTNCdiagSoftware for the analysis of status and diagnostic information of digital drive systems72TNCoptSoftware for putting digital control loops into service73ConfigDesignSoftware for creating the machine configuration72KinematicsDesignSoftware for creating the machine kinematics, initialization of DCM68Integrated oscilloscope 72Trace function 73API DATA function 73Table function 73OLM (online monitor) 73Log 73TNCscope 73Bus diagnostics 74Data interfaces Ethernet2 x 1000BASE-T80USBRear: 4 x USB 3.0Front: may vary based on the component description8080ProtocolsStandard data transmission 80Blockwise data transfer 80LSV2 809
Short description Program entry TNC 640OptionFunctionStandardFunctions for the userBasic version: 3 axes plus closed-loop spindle0-7 A total of 14 additional NC axes or 13 additional NC axes plus second spindle7778Digital current and speed control42HEIDENHAIN KlartextAccording to ISODirect loading of contours or machining positions from DXF files and saving as Klartext contouringprograms, or as point tablesPosition values Nominal positions for lines and arcs in Cartesian coordinates or polar coordinatesIncremental or absolute dimensionsDisplay and entry in mm or inchesTool compensation Tool radius in the working plane and tool lengthRadius-compensated contour look ahead for up to 99 blocks (M120)Three-dimensional tool-radius compensation for the later changing of tool data without needing torecalculate the program9Tool tables Multiple tool tables with any number of toolsCutting data Automatic calculation of spindle speed, cutting speed, feed per tooth, and feed per revolutionConstant contourspeed Relative to the path of the tool centerRelative to the tool’s cutting edgeParallel operation Creating a program with graphical support while another program is being run3-D machining 99992Motion control with smoothed jerk3-D tool compensation via surface-normal vectorsUsing the electronic handwheel to change the angle of the swivel head during program runwithout affecting the position of the tool point (TCPM Tool Center Point Management)Keeping the tool normal to the contourTool radius compensation normal to the tool directionManual traverse in the active tool-axis system3-D radius compensation depending on the tool’s contact angleRotary tablemachining88Programming of cylindrical contours as if in two axesFeed rate in d switchover between milling and turningConstant surface speedTool radius compensationCycles for roughing, finishing, recessing, thread turning, and recess turningBlank form updated in contour cyclesTurning-specific contour elements for recesses and undercutsOrientation of the turning tool for outside or inside machiningInclined turningSpeed limitingEccentric turning (also requires software option 135)5050Straight lineChamferCircular pathCircle centerCircle radiusTangentially connecting circular arcCorner roundingRecessUndercutContour elements10 99
TNC 640OptionStandardFunctionContour approach and departure Via straight line: tangential or perpendicularVia circular arcAdaptive feed control45AFC: Adaptive Feed Control adjusts the contouring feed rate to the current spindle powerCollision monitoring404040Dynamic Collision Monitoring (DCM)Graphic depiction of the active collision objects (high-resolution M3D format)Tool carrier monitoringFK free contourprogramming FK free contour programming in HEIDENHAIN Klartext format with graphical support forworkpiece drawings not dimensioned for NCProgram jumps SubprogramsProgram section repeatCalling any program as a subprogramFixed cycles Coordinatetransformations Q parametersProgramming withvariables Programming aidsCAD viewer Drilling, tapping with a floating tap holder, rigid tappingPeck drilling, reaming, boring, counterboring, centering50 Area clearance cycles, longitudinal and transverse, paraxial and contour parallel50 Recessing cycles, radial/axial50 Radial/axial recess turning cycles (combined recessing and roughing motion)Milling internal and external threads50 Turning internal and external threads50 Hobbing13596 Interpolation turning (not with functional safety (FS))Clearing level and oblique surfacesMulti-operation machining of straight and circular slotsMulti-operation machining of rectangular and circular pocketsPoint patterns for circles, lines, and DataMatrix codesContour train, contour pocketContour slot with trochoidal millingOEM cycles (special cycles developed by the machine tool builder) can be integratedEngraving cycle: engrave text or numbers in a straight line or on an arc844Shifting, rotating, mirroring, scaling (axis specific)Tilting the working plane, PLANE functionManually definable: shifts, rotations, and handwheel superimpositioning can be manually definedvia global program settingsMathematical functions , , –, *, /, sin α, cos α, tan α, arc sin, arc cos, arc tan, an, en, In, log,square root of a, square root of (a2 b2)Logical operations ( , /, , )Calculating with parenthesesAbsolute value of a number, constant π, negation, truncation of digits before or after the decimalpointFunctions for calculation of circlesFunctions for text processing CalculatorComplete list of all current error messagesContext-sensitive help function for error messagesTNCguide: the integrated help system; user information is available directly on the TNC 640, withcontext-sensitive callingGraphic support for programming cyclesComment and structure blocks in the NC program Display of standardized CAD file formats on the TNC11
TNC 640OptionStandardFunctionTeach-In Actual positions can be transferred directly into the NC programTest graphicsDepictions Graphical simulation before a program run, even while another program is runningPlan view / projection in 3 planes / 3-D view, also in tilted working planeDetail zoom3-D line graphics For verification of programs created offlineProgramming graphics In the Programming and Editing mode, the contours of entered NC blocks are rendered (2-Dpencil-trace graphics), even while another NC program is runningProgram-run graphicsDisplay modes Graphic simulation during real-time machiningPlan view / projection in 3 planes / 3-D viewMachining time Calculation of machining time in the Test Run operating modeDisplay of the current machining time in the Program Run operating modesReturning to thecontour Mid-program startup at any block in the program, and approach of the calculated nominal positionfor continued machiningProgram interruption, contour departure and approachPreset management One table for storing presetsDatum tables Multiple datum tables for storing workpiece-specific datumsPallet tables Workpiece-oriented execution of pallet tables (with any number of entries for the selection ofpallets, NC program, and datums)Parallel secondaryaxes Compensation of movement in the secondary axes U, V, W through the principal axes X, Y, ZMovements of parallel axes included in the position display of the associated principal axis (sumdisplay)Defining the principal and secondary axes in the NC program makes it possible to run programs ondifferent machine configurations Touch probe cyclesConversationallanguages12 48Calibrating the touch probeCompensation of workpiece misalignment, manual or automaticReference point setting, manual or automaticAutomatic tool and workpiece measurementAutomatic measurement and optimization of machine kinematicsEnglish, German, Czech, French, Italian, Spanish, Portuguese, Dutch, Swedish, Danish, Finnish,Norwegian, Slovenian, Slovak, Polish, Hungarian, Russian (Cyrillic), Romanian, Turkish, Chinese(traditional and simplified), Korean
Software optionsSoftwareoptionnumberSoftware optionWith NCsoftware34059x- orlaterIDCommentPage0Additional Axis 101354540-01Additional control loop 1201Additional Axis 201353904-01Additional control loop 2202Additional Axis 301353905-01Additional control loop 3203Additional Axis 401367867-01Additional control loop 4204Additional Axis 501367868-01Additional control loop 5205Additional Axis 601370291-01Additional control loop 6206Additional Axis 701370292-01Additional control loop 7207Additional Axis 801370293-01Additional control loop 8208Advanced FunctionSet 101617920-01Rotary table machining Programming of cylindrical contours as if in two axes Feed rate in mm/min51Coordinate transformation Tilting the working plane, PLANE function52Interpolation Circular in 3 axes with tilted working plane9Advanced FunctionSet 201617921-013-D machining52 3-D tool compensation via surface normal vectors Using the electronic handwheel to change the angle ofthe swivel head during program run without affectingthe position of the tool point (TCPM Tool CenterPoint Management) Keeping the tool normal to the contour Tool radius compensation normal to the tool direction Manual traverse in the active tool-axis systemInterpolation Linear in more than 4 axes (export license required)18HEIDENHAIN DNC01526451-01Communication with external PC applications over COMcomponent8240DCM Collision0102526452-01Dynamic collision monitoring (DCM)6742CAD Import08526450-01Importing of contours from 2-D and 3-D models, e.g.,STEP, IGES, DXF44Global PGM Settings05576057-01Global program settings5345Adaptive Feed Control(AFC)02579648-01Adaptive feed control6246Python OEM Process01579650-01Execute Python e cycles for the automated measurement ofrotary axes7049Double-Speed Axes01632223-01Short control-loop cycle times for direct drive motors6013
SoftwareoptionnumberSoftware optionWith NCsoftware34059x- orlaterIDCommentPage50Turning01634608-01Turning functions Tool management for turning Tool-tip radius compensation Switching between milling and turning modes ofoperation Lathe-specific contour elements Package of turning cycles5452KinematicsComp05661879-01Spatial compensation of errors in rotary andlinear axes (export license required)7156 - 61OPC UA NC Server 1to 6101291434-01 Connection of an OPC UA applicationto1291434-0683774 Additional Axes01634613-014 additional control loops20788 Additional Axes01634614-018 additional control loops20923D-ToolComp07679678-013-D radius compensation based on the contact angle(only with the Advanced Function Set 2 software option)7193Extended ToolManagement01676938-01Expanded tool management: Tooling list(list of all tools of the NC program) T usage sequence(sequence of all tools inserted during the program)96Adv. Spindle Interp.05751653-01Additional functions for an interpolated spindle Interpolation turning, coupling Interpolation turning, contour finishing101 - 130OEM SoftwareOption02579651-01to579651-30Software options of the machine manufacturer131Spindle Synchronism05806270-01Synchronization of two or more spindles82133Remote DesktopManager01894423-01Display and remote operation of external computer units(e.g., a Windows PC)82135SynchronizingFunctions041085731-01 Expanded synchronization of axes and spindles53136Visual Setup Control061099457-01 VSC: camera-based monitoring of the setup situation53137State Reporting091232242-01 State Reporting Interface (SRI): provision of operatingstatuses74141Cross Talk Comp.02800542-01CTC: compensation of axis couplings65142Pos. Adapt. Control02800544-01PAC: position-dependent adaptation of controlparameters65143Load Adapt. Control02800545-01LAC: load-dependent adaptation of control parameters64144Motion Adapt. Control02800546-01MAC: motion-dependent adaptation of controlparameters64145Active Chatter Control02800547-01ACC: active suppression of chatter6314
SoftwareoptionnumberSoftware optionWith NCsoftware34059x- orlaterIDCommentPage146Active VibrationDamping04800548-01AVD: active vibration damping65154Batch ProcessManager051219521-01 Planning and executing multiple machining operations53155ComponentMonitoring091226833-01 Monitoring for component overloading and wear68156Grinding101237232-01 Grinding function Jig grinding Switching between normal operation and dressingmode Reciprocating stroke Grinding cycles Tool management for grinding and dressing56157Gear Cutting091237235-01 Functions for the machining of gear teeth55158Advanced Function Set 09Turning1237237-01 Extended turning cycles and functions55160Integrated FS: Basic101249928-01 Enables functional safety and four safe control loops47161Integrated FS: Full101249929-01 Enables functional safety and maximum number of safecontrol loops ( 10)47162Add. FS Ctrl. Loop 1101249930-01 Additional control loop 147163Add. FS Ctrl. Loop 2101249931-01 Additional control loop 247164Add. FS Ctrl. Loop 3101249932-01 Additional control loop 347165Add. FS Ctrl. Loop 4101249933-01 Additional control loop 447166Add. FS Ctrl. Loop 5101249934-01 Additional control loop 547167Optimized ContourMilling101289547-01 OCM: optimized contour milling6315
HSCI control componentsMain computersMain computerThe MC 85xx and MC 366 main computer contain the following: Processor: Core i7/3, 1.7 GHz Main memory: 4 GB RAM Gbit HSCI interface to the controller unit and to othercontrol components HDL2 interface to the BF monitor(with electrical cabinet versions) 4 x USB 3.0 ports (e.g., for the TE 7x5 operating panel)To be ordered separately and installed in the main computer by theOEM: SSDR memory card with the NC software The System Identification Key (SIK) component for theenabling of control loops and software optionsThe following HSCI components are required for operation of theTNC 640: MC main computer Controller unit PLB 62xx PLC I/O unit (system PL; integrated in UxC)InterfacesFor use by end users, the MC is equipped with the USB 3.0 andEthernet interfaces. Connection to PROFIBUS DP or PROFINET IOis possible either via additional modules or by means of acombined PROFIBUS DP / PROFINET IO module.Export versionBecause the complete NC software is on the storage medium,no export version is required for the main computer itself. Onlythe easily replaceable storage medium and SIK component areavailable as export versions.Gen 3 labelsThe different Gen 3 labels identify how control components can bedeployed.Gen 3 ready: These components can be used in systems withGen 3 drives (UVR 3xx, UM 3xx, CC 3xx) and in systems with a1xx inverter system (UVR 1xx, UE 2xx, UR 2xx, CC 61xx).Gen 3 exclusive: These components can be used only in systemswith Gen 3 drives (UVR 3xx, UM 3xx, CC 3xx).16
VersionsVarious versions of the MC main computer are available: Installation in the electrical cabinet:The MC 306 are installed in the electrical cabinet. The operatingpanel requires HSCI, USB, and HDL2 cables as control lines Installation in the operating panel:The MC 85x2 and MC 366, together with the BF monitor, forma single unit that is installed directly into the operating panel.With the exception of the power supply line, only one HSCIconnecting cable to the electrical cabinet is needed.MC 8512 with main computerinstalled on the backMC 8532 with main computerinstalled on the backMC 366 with main computer installed on the backInstallation )IDMC 306ElectricalcabinetSSDRIntel Xeon E3,2.1 GHz, quadcore8 GB 65 W 4.0 kg1180045-xxMC 8512OperatingpanelSSDRIntel Core i7/3,4 GB1.7 GHz, dual-core 75 W 7.5 kg1243919-xxMC 8532OperatingpanelSSDRIntel Core i7/3,4 GB1.7 GHz, dual-core 75 W 7.5 kg1189190-xxMC 366OperatingpanelSSDRIntel Core i7-3,8 GB1.7 GHz, dual-core 75 W 7.5 kg1246689-xx*)Test conditions: Windows 7 (64-bit) operating system, 100 % processor loading, no load on interfaces, nofieldbus moduleMC 30617
Software optionsSoftware options allow the performance of the TNC 640 to beadapted to one’s actual needs at a later time. The software optionsare described on page 13. They are enabled by entering keywordsbased on the SIK number and are saved in the SIK component.Please provide the SIK number when ordering new options.Storage mediumThe storage medium is removable and must be ordered separatelyfrom the main computer. It contains NC software version34059x-xx. The NC software is based on the HEIDENHAINHEROS 5 operating system.32 GB SSDR solid state disk for the operating panelFree PLC memory space 1 GBFree NC memory space 18 GBFor main computerMC 85x2 andMC 366Export license requiredID 810288-10No export license requiredID 810288-60SSDR for operating panel240 GB SSDR solid state disk for the electrical cabinetFree PLC memory space 4 GBFree NC memory space 189 GBFor main computerMC 306Export license requiredID 1279027-10No export license requiredID 1279027-60SSDR MC 306SIK componentThe SIK component contains the NC software license forenabling control loops and software options. It gives the maincomputer an unambiguous ID code—the SIK number. The SIKcomponent is ordered and shipped separately. It must be insertedinto a slot provided for it in the MC main computer.The SIK component with the NC software license exists indifferent versions based on the enabled control loops and softwareoptions. Additional control loops can be enabled later by entering akeyword. HEIDENHAIN provides the keyword, which is based onthe SIK number.When ordering, please provide the SIK number of your control.When the keywords are entered in the control, they are saved inthe SIK component, thereby enabling and activating the softwareoptions. Should servicing become necessary, the SIK componentmust be inserted into the replacement control in order to enable allof the required software options.Master keyword(general key)18For putting the TNC 640 into service, there is a master keywordthat enables all software options once for 90 days. After thisperiod, the software options can be activated only with the correctkeywords. The general key is activated via a soft key.SIK component
TNCkeygen(accessory)TNCkeygen is a collection of PC software tools for generatingenabling keys for HEIDENHAIN controls for a limited period oftime.With the OEM Key Generator, you can generate enabling keysfor software options by entering the SIK number, the softwareoption to be enabled, the enabling period, and an OEM-specificpassword. This activation is limited to a period of 10 to 90 days.Each software option can be enabled only once; this is performedindependently of the master keyword.The OEM daily key generator generates an enabling key for theprotected OEM area, thus granting the user access on the day it isgenerated.NC softwarelicense andenabling ofcontrol loopsdepending onthe CC2 x CC 308CC 306 CC 308NC software licenseWithoutoptionIncl. option 8 Incl. options8 9Incl. options8 9 50SIKSIKSIKSIK4 ID 674989-20ID 674989-70ID 674989-09ID 674989-59ID 674989-01ID 674989-51ID 674989-28ID 674989-785 ID 674989-24ID 674989-74ID 674989-17ID 674989-67ID 674989-02ID 674989-52ID 674989-29ID 674989-796 ID 674989-25ID 674989-75ID 674989-18ID 674989-68ID 674989-03ID 674989-53ID 674989-30ID 674989-807 ID 674989-26ID 674989-76ID 674989-19ID 674989-69ID 674989-04ID 674989-54ID 674989-31ID 674989-818 ID 674989-27ID 674989-77ID 674989-23ID 674989-73ID 674989-05ID 674989-55ID 674989-32ID 674989-829 ID 674989-06ID 674989-56ID 674989-33ID 674989-8310 ID 674989-07ID 674989-57ID 674989-34ID 674989-84ID 674989-10ID 674989-60ID 674989-35ID 674989-85ID 674989-11ID 674989-61ID 674989-36ID 674989-86ID 674989-12ID 674989-62ID 674989-37ID 674989-87ID 674989-13ID 674989-63ID 674989-38ID 674989-8811 12 13 14 Only through subsequentenabling of control loops(additional axes)15 ID 674989-14ID 674989-64ID 674989-39ID 674989-8916 ID 674989-15ID 674989-65ID 674989-40ID 674989-9017 –24)CC 310 CC 302CC 310CC 308CC 306Activecontrol loopsRecommended combinationsOnly through subsequent enabling of control loops (additionalaxes)(Italics: export version)For a description of the CC 3xx controller units, please refer to theGen 3 Drives
TNC contouring control with drive system from HEIDENHAIN General information TNC 640 Contouring control for milling machines, milling-turning machines, and machining centers Axes: up to 24 control loops (22 control loops with functional saf
User's Manual: All TNC functions that have no connection with cycles are described in the User's Manual of the TNC 640. Please contact HEIDENHAIN if you require a copy of this User's Manual. ID of User's Manual for conversational programming: 892903-xx. ID of User’s Manual for DIN/ISO programming: 892909-xx.
Hermle B300 (2x) 800 600 500 CNC Heidenhain TNC530, 5-axis Hermle C1200 U 1200 800 500 CNC Heidenhain TNC430, 5-axis Fehlmann Picomax 54 500 250 160 CNC Heidenhain TNC310, 3-axis Hermle C40 850 700 500 CNC Siemens 840D, 5-axis Hermle UWF 902 S 600 450 500 CNC Heidenhain TNC426, 4-axis Hermle C 800V 800 600 500 CNC Heidenhain TNC430, 3-axis
-- Prohibits a TNC driver from accepting a request for transportation except through the TNC's digital network. -- Requires a TNC digital network to display a picture of the TNC driver and the registration plate number of the personal vehicle to be used for a prearranged ride before a TNC rider enters the vehicle.
HEIDENHAIN are usually integrated as components into complete systems. In such cases, comprehensive testing of the complete system is required, irrespective of the specifications of the individual devices. Parts subject to . PWM - - - - 6 20 Motor co
The TNC certification program covers the IF-IMC, IF-IMV, and IF-PEP specifications. Before receiving TNC certification, products are thoroughly tested for specification compliance and for interoperability with other certified products. TNC certification ensures that products correctly implement the TNC specifications and work together in the
individually (using the term "TNC License"), and provides for an initial issuance of 1 00 TNC Licenses in 2015, with provisions for additional issuances in future years. As an alternative to this cap on the number of TNC Licenses, CCTI has developed a technological means to limit the number of TNOs operating on a TNC app to 100 at any
Yaesu FTM-350, FT1DR, VX-8R, VX-8DR Any radio with data jack and external TNC TNC2, MFJ, Byonics TinyTrak, Argent OpenTracker, TNC-X/TNC-Pi Byonics MT-AIO SignaLink (or other sound card interface) and software in place of TNC
The first concert showcases one of Australia’s best pianists, with a special ballet accompaniment, and the second will star the just announced winner of the Sydney International Piano Competition. Head of Piano Studies at the Australian National Academy of Music, Timothy Young will perform the first concert in the series on Tuesday 7 August. Young will challenge the audience with the .
