QUICK OPERATING 1/4-TURN FASTENERS 4002 SERIES
QUICK OPERATING 1/4-TURN FASTENERSThe 4002 Series fasteners utilize a variety ofgrommets designated to reinforce the panel for added4002 SERIESstrength. Certain 4002 series 1/4-turn fasteners arequalified to MIL-F-5591* specifications for sizes5 and 7.ATo Order a Complete Fastening System:1. Select receptacle to be used. Stud part numbersvary depending upon the specific receptacle used.2. Select style of stud to be used, then combinethicknesses of panel and frame to determine totalthickness, “G”. Find the specific stud part numberadjacent to “G” Total Thickness column with respect toreceptacle selected.3. If you are ordering long studs (-16 or greater), you willneed to order a Stud Retaining Ring. Shorter studs (-15and under) are self-captivating and do not requireretaining rings.4. A Grommet is required for all 4002 studs except PartNumber 40S128. A choice of Flared or Retaining RingRetained styles are available.Section ContentsPage No.Stud AssembliesA-46 - A-47ReceptaclesA-48 - A-50GrommetsRetaining Ring RetainedFlare RetainedGrommet InstallationRetaining Ring RetainedFlare RetainedStud Assembly InstallationA-51 - A-52A-52 - A-53A-54 - A-56A-57A-58Sealed Stud and Grommet InstallationA-59Receptacle InstallationA-60A-61 - A-62*Meets the design, physical and performance requirements of Stud Dash Number SelectionWeights for Flare Retained GrommetsA-63MIL-F-5591. However, full mechanical properties testing maynot be performed on each production lot.A-45
QUICK OPERATING 1/4-TURN FASTENERS4002 SERIES4002 Series. Stud Assemblies and ReceptaclesNote: Part numbersshown are basicpart numbers only.See orderinginformation onPage A-62 for requireddash numbers.Slotted RecessCross Recess“Tamper Resistant”R ecessPart No.MaterialPart No.Part No.Stainless Steel4002-[ ]S40S5-[4055-[ ]S]SStainless SteelHigh Strength40S41-[ ]SStainless Steel(Spring: Inconel “X”)Steel (Cadmium Plated,Yellow Chromate)Part No.40S119-[ ]-3AA40S80-[ ]B40S45-[ ]4002-[ ]Steel (Zinc Plated,Clear Chromate)Steel(Nickel Plated)Recess Style perNAS400040S5-[ ]40S119-[ ]-3BB40S5-[ ]C40S80-[ ]C40S5-[ ]D40S80-[ ]E40S79-[ ]Steel(Head: Chrome Plated)Steel (Zinc Plated,Yellow Chromate)Maximum Service Temperature: Stainless Steel with inconel “X” Spring—700 F.; Stainless Steel—550 F.;Sealed Stud Assembly , P/N 40S37-[ ]—130 F .; all others 450 F .Note: 4002 Series stud assemblies seat nominally flush with mating grommet. For Wing, Bail Handle or Knurled Knob versions,top side protrusion is nominally equal to mating grommet “B” dimension plus the height of the wing, handle or knob.Grommetless StudSpecifications:This series utilizes a variety of grommets which mustbe installed into the top panel. They significantlyenhance the system’s performance.Ultimate tensile strength: 1050 lbs.Working strength: 700 lbs.Stud grip increments: .030 inch.Contact factory for strengths for stainless steel stud assemblies.For other styles, materials, or finishes, please contactCamloc Products Division.Ultimate tensile strength for stainless steel: 735 lbs.Working strength: 500 lbs.Minimum Preload - 50 LBS*S Protruding Slotted Head Part No. 40S128-( )-1AA*40S128Protruding HeadNOTE: This stud does not require a grommet, but mustbe used with retaining ring part number 40S142-1-1AA.Retaining RingPart Number40S142-1-1AACRES SpringSteel (Passivated)A-46
QUICK OPERATING 1/4-TURN FASTENERS4002 SERIESAH ex R ecess4mm Part No.6mm Part No.SealedPart No.Fixed WingPart No.4002-[ ]SWFolding Bail HandlePart No.Knurled KnobPart No.40S83-[ ]40S37-[ ]†4002-[ ]W40S47-[ ]40S83-[ ]A40S77-[ ]40S47-[ ]A40S83-[ ]B40S122-[ ]-1AA40S122-[ ]-2AA† Not available with dash numbers smaller than #4.Refer to installation instructions on page A-59.A-47
QUICK OPERATING 1/4-TURN FASTENERS4002 SERIES4002 Series. ReceptaclesStandardMountingMateri alPartNo.—Stai nless SteelStai nless Steel(Red D ye)Steel(C admi um Plated)Si li con Bronze(C admi um Plated)Zi nc(Zi nc Plated)Steel (C ad. Plated)Receptacle Element:Si li con Bronze(C ad. Plated)Steel (C ad. Plated)Receptacle Element:Zi nc (Zi nc Plated)Wei ght(per100 pcs.)(lb—s.)Ri vetHoles———214-16S214-16SD—Plai nC ’ Sunk—1.761.68——214-16214-16D—Plai nC ’ Sunk—1.851.77214-16EPlai n1.44—N arrow WidthWei ghtPartRi vet(perNo.Holes 100 ————214-16NPlai n214-16ND C ’ Sunk——1.801.72EncapsulatedSee N ote 1 for sealingWei ghtPartRi vet(perNo.Holes100 ——40R12-140R12-2——2.45—Plai nC ’ �—StandardMountingContinuedMateri alStai nless SteelSteel (C ad. Plated)Receptacle Element:Si li con Bronze(C ad. Plated)Steel (C ad. Plated)Receptacle Element:Zi nc (Zi nc Plated)Alumi numFl o at i n g (1/8" t o t al )Wei ghtPartRi vet(perNo.Holes 100 pcs.)(lbs.)244-22S Plai n2.77Fl o at i n g (1/8" t o t al )E n c ap s u l at edPartNo.Ri vetHoles------Wei ght(per100 pcs.)(lbs.)---PartNo.AD i m.Ri vetHoles---------Wei ght(per100 pcs.)(lbs.)---244-22Plai n2.99244-22CPlai n3.98------------244-22EPlai n2.61244-22ECPlai 19-.013Plai n------------------40R8-16-1.033-.027Plai n0.11------------------40R8-16-2.033-.027D i mpled0.11Notes: 1. Use to seal against leakage of air, dust or water. Install with suitablesealing compound such as 3M #EC-847 or adhesive silicon sealant.2. Receptacles and Shims with countersunk holes are for sure withdimpled panels.A-48Sh i m sSee N ote 1 for seal i ngMaximum Service Temperatures for Standard Mounting Types:Stainless Steel—700 F.; Steel (Cadmium Plated) andSilicon Bronze (Cadmium Plated)—450 F.;Silicon Bronze with Brass Cap and Steel with ZincReceptacle Element—300 F.; Aluminum—350 F.
QUICK OPERATING 1/4-TURN FASTENERSL ig h t weig h tFlo at in g (1/16" t o t al)WeightPartRivet(perNo.Holes100 4002 SERIESAFlo at in g (1/16" t o t al)En c ap s u lat edSee Note 1 for Weight(per100 ——————Weight(per100 pcs.)(lbs.)3.313.33——————2-Piece Floating Receptacles/Spotweld Attachmentover conventional designs. Choose fromversions within 1/16 inch or 1/8 inch total float.These receptacles are designed to be attached byspotwelding. Separate cage and receptacle elementallow smaller envelopes and significant weight savingsOrder receptacleelement and cageseparately.For 1/16 inch Total FloatReceptacle ElementMaterialSteel(Cadmium Plated)Silicon Bronze(Cadmium Plated)Zinc(Zinc Plated)For 1/8 inch Total FloatC agesStandardEncapsulatedPart No.Weight *Part No.Weight *Part -----Receptacle ElementC agePart No.Weight *Part ---701E1.29------*Weights shown are in lbs. per 100 pcs.A-49
QUICK OPERATING 1/4-TURN FASTENERS4002 Series. Receptacles continuedSide MountingFloating (1/16" total)MaterialSteel (Cad. Plated)Receptacle Element:Silicon Bronze(Cad. Plated)Floating (1/16" total)EncapsulatedSee Note 1 for sealingNo.RivetHolesWeight(per100 pcs.)(lbs.)PartNo.RivetHolesWeight(per100 tes:1. Use to seal against leakage of air, dust or water. Install with suitablesealing compound such as 3M #EC-847 or adhesive silicon sealant.2. Maximum Service Temperature: 450 F.Clip-inMaterialSteel & Zinc Alloy(Zinc Plated)Provides ¼” None––––40R44-1-1AANoneSteel (Cad. Plated)Receptacle Element:Silicon Bronze(Cadmium Plated)Maximum Service T emperature: 300 F.A-50Bottom ViewBottom ViewProvides 1/8" Float4002 SERIES
QUICK OPERATING 1/4-TURN FASTENERS4002 SERIES4002 Series. Grommets4002 Series stud assemblies must be used inconjunction with one of the grommets shown here.Both flush mounting and plus flush grommets areavailable with either retailing ring or flare retention.ARetaining Ring RetailedPlus Flush GrommetsRing retained grommets are easily installed without theneed for extensive special tooling.P C Min - .042 Max (retaining ring thickness - .008PartNo.PMax.Thickness4002-N2SMaterialStainless Steel(Cadmium Plated)Steel(Cadmium Plated)Stainless SteelSteel(Cadmium Plated)Alloy Stee(Cadmium Plated,Olive Drab)Stainless SteelSteel(Cadmium Plated)Alloy Steel(Cadmium Plated,Olive 4002-040G6-14002-N3Steel(Cadmium Plated).072128ABCDGMin.(Note .193.122.114.029.023Weight(per 100 193.244.128.120.054.048.1500.60Retaining Ring RetainedFlush Mounting Grommets (Standard Series)PartNo.P Max. 440G54002-HS4002-H40G10.117.086MaterialStainless SteelSteel(Cadmium Plated)Alloy Steel(Cadmium Plated,Olive Drab)Stainless SteelSteel(Cadmium Plated)Alloy Steel(Cadmium Plated,Olive Drab)Notes: (Applies to both Plus Flush and Flush Mounting Versions above.)*1. Grommets will protrude from the back side of panel. Minimum totalthickness “G” must be observed to prevent grommets from jammingagainst the receptacle. (Under certain conditions “G” minimum may bereduced. See Note 3 on Page A-62.BCG*Min.(Note 1)Weight(per100 1.193.173.167.1500.330.332. Panels with thicknesses greater than “P” Max. may be back counterbored.3. Maximum Service Temperatures: Stainless — 700 F.: Steel — 450 F.A-51
QUICK OPERATING 1/4-TURN FASTENERS4002 SERIES4002 Series. GrommetsRetaining Ring RetainedFlush Mounting Grommets.(High Shear Series)Maximum Service Temperature: — 450 Min.Alloy Steel(Cadmium Plated).065.092.113.128.120.150.175.175Important Notes:*1. Grommets will protrude from the back side of panel. Minimum totalthickness “G” must be observed to prevent grommets from jammingagainst the receptacle. (Under certain conditions “G” minimum maybe reduced. See Note 3 on Page .156-.159.177-.180.192-.195Weight(per 100 pcs.)(lbs.).37.41.50.502. For maximum shear capability, receptacle mounting hole in substructure maybe reduced to .578 inch. This hole size provides no accommodation formisalignment.Flare RetainedFlush and Plus Flush GrommetsFlare retained grommets will accommodate relatively thickpanels often eliminating the need for back counterboring.Flared grommets should also be specifiedSeriesPlus Flush,StandardPart No.Material40G16-[ ]Alloy Steel(Cadmium Plated)40G16-[ ]SStainless Steel4002-P3-[ ]Steel(Cadmium Plated)Alloy Steel(Nickel Plated)Alloy Steel(Cadmium Plated,Clear Chromate)Stainless SteelSteel(Cadmium Plated)Steel(Nickel Plated)Stainless SteelSteel(Cadmium Plated)Alloy Steel(Cadmium Plated)40G16-[ ]-140G16-[ ]-2Plus Flush,LargeBearingArea4002-P4-[ ]A4002-P4-[ ]4002-P4-[ ]B40G15-[ ]SFlush4002-P2-[ ]40G15-[ ]Notes: 1. Maximum Service Temperature: Stainless Steel — 700 f.; Steel(Cadmium Plated) — 450 F.; Steel (Nickel Plated) — 550 F.2. For weighs see Page A-63.A-52when axial grommet to movement must be restricted.Note: Part numbers shown are basic part numbers only. See Date Tableindicated below for “P” panel thickness, “L” dimension and requiredgrommet length dash number.A.di Data TablesLook up “P” and “L” dimensions, plusgrommet length dash number, from thedata table indicated below. (See next #3#2
QUICK OPERATING 1/4-TURN FASTENERS4002 Series. Grommets4002 SERIES(continued)Data Tables for Flared Retained Grommets.(“P”, “L” and Grommet Dash Numbers)To Select Grommet Dash NumberA1. Determine “P” panel thickness.2. Locate “P” thickness in the appropriate tablebelow.3. Find the corresponding dash number to the right.DATA TAB L E 1DATA TAB L E 3PPanel ThicknessLGrommet LengthDash NumberPPanel ThicknessLGrommet LengthDash TA TAB L E 2PPanel ThicknessLGrommet LengthDash 189.220-.231-160.190-.219.250-.261-190Notes: 1. For longer lengths contact Camloc Products Division.2. Data tables are applicable to specific part numbers. Select thecorrect table as indicated on Page .4071.453-1.433-13751.468-1.5321.578-1.608-1500See Grommet Weights on Page A-63.How to Order:Example:“P” thickness .125 inch.Grommet selected: 40G15-[ ]SFrom data above, Table #2 applies.Grommet Dash Number selected from Table #2: -100.Complete part number: 40G15-100S.A-53
QUICK OPERATING 1/4-TURN FASTENERS4002 SERIES4002 Series. Panel Preparation andInstallation Data(For Ring Retained Grommets)Installing GrommetPlus Flush GrommetsInsert grommet into mounting hole and captivate withretaining ring. Please see Page A-56 for more information.Drill #30 (.1285) pilot hole. Enlarge pilot hole to .478-.473 diameter withhole saw HS-471. “P” maximum panel thickness varies with grommetselected. Please see Page A-51 for tabulation.Panels with thicknesses greater than “P” maximum must be backcounterbored to a concentric .688 inch diameter with a remainingmaterial thickness not exceeding “P” maximum.Note:Hole saws and counterboring tools are available as a convenience inselected sizes. Please see Page A-55.Typical InstallationsFlush Mounting GrommetsAlternate Dimpling Method.“Thin” panels constructed from ductile materials allow useof an alternative method which eliminates the need forgrommet retaining rings.PMax.BMax.HoleSawDimpling Tool Set*(order both P/Ns).064.086.074.117HS-4714G200M-[ ]4G200F-[ ]* See Next page for dimpling tool ordering information.Dimpled Panel Preparation for panel thicknesses “P” up to .086inch. Drill #30 (.1285) pilot hole. Enlarge pilot hole to .478-.473diameter with hole saw HS-471. Then dimple using toolsspecified in the table above. Spot face back side of panel ifrequired to meet “B” maximum.Note: When using panels constructed of ductile materials, seealternate dimpling method.PMax.086HoleS awHS-418Dimpling Tool Set* Closing Tools*(order both P/Ns) (order both P/Ns)4-G100M-[ ]4-G100F-[ ]4-GM-[ ]4-GF-[ ]* See Next Page for dimpling tool ordering information.For panel thickness “P” large than .086 inch, drill #30 pilothole. Enlarge pilot hole using hole saw specified below toX diameter. C’Sink using tool specified.XDia.HoleSawC’SinkTool40G1High shearversion only.500Min.N/A4GC-500or4GC-1-500*All otherflush mountingring retainedversions.478.473HS-4714GCor 4GC-1-470*Grommet*Supplied with optional 1/4-28-UNF-2A Thread“P” maximum panel thickness varies with grommet selected. Please seePages A-51 and A-52. Panels with thicknesses greater than “P” maximummust be back counterbored to a concentric .688 inch diameter with aremaining material thickness not exceeding “P” maximum.Note: Hole saws, counterboring tools and countersinks are available as aconvenience in selected sizes (see alternative dimple method).A-54Drill #30 (.1285) pilot hole. Enlarge hole using hole sawP/N HS-418. Then dimple using tools tabulated above.Insert grommet and push panel back using closing toolspecified. Panel must be securely engaged behind shoulderof grommet for positive retention.
QUICK OPERATING 1/4-TURN FASTENERS4002 SERIES4002 Series. Panel Preparation andInstallation Data (continued)Installation Tools for Ring Retained Grommets.Hole SawsCounterboring Tool 4G2CAccurately sizes grommet mounting holes.For back counterboring thick panels to .688 concentricdiameter.Part No.ApplicationHS-418Alternate dimplemethod onlyHS-471All mounting holesexcept alternatedimple methodCountersinking Tool (4GC)Forms C’Sink required for flush mounting grommets.Dimpling and Closing Tools(Part number for dimpling and closing tools are listed withthe installation instructions on preceding 0AdaptorsMay be used to adapt any C’Sinking or C’Boringtool for use in a drill chuck.Dash Nos. for Shank Diameters and LengthsUsed On Dimpling and Closing nk ToolThreadAdaptorPart No.-25/165/85/16-32 NEF-2BT19-35/167/81/4-28 UNF-2BT19-1-43/87/8Note:It is recommended that tools be ordered in sets.However, punch and dies may be ordered separately.Tooling Part Number StructureExample: 4G200M-22 5/16" Dia. x 5/8" Long ShankM PunchF DieA-55A
QUICK OPERATING 1/4-TURN FASTENERSRetaining Rings for Ring RetainedGrommets.4002 SERIESRetaining Ring InstallationStandard Retaining RingWeight(per100 )0.07InstallationTool ToolInstallationApplicationFor use withall ringretainedgrommetsexcept40G1 SeriesToolT261. Place grommet in prepared hole.2. Place mandrel into grommet.3. Place retaining ring over mandrel as shown.4. Push handle over mandrel until sharp ring is fullyseated behind shoulder of grommet.Installed GrommetRetaining Ring Installation Tooland Replacement Components.DescriptionComplete Installation ToolRubber TipMandrelHigh Shear Retaining RingPartNo.MaterialR4TAlloy Steel(CadmiumPlated)40G42 ElgiloyA-56Weight(per100 pcs.)(lbs.)ApplicationTool0.15For use with40G1 SeriesHigh ShearGrommets onlyT39-1Part No.T-26T-26-1T-26-2
QUICK OPERATING 1/4-TURN FASTENERS4002 SERIES4002 Series. Panel Preparation andInstallation Data (continued)For Flare Retained GrommetsPlus Flush GrommetsInstallation ToolsAFlaring ToolsUsed to flare grommets in place.Tool Part NumbersGrommetPart No.Form .515-505 mounting hole. Insert grommet into paneland flare using appropriate flaring tools from table at right.4002-{P2P3P440G1540g16Typical InstallationFlush Mounting GrommetsForm .515-.505 mounting hole. Countersink with C’Sink tool P/N 4-GC-500. Insert grommet into panel and flare usingappropriate flaring tool set from table at right.PunchDie4-GM-[ ]4-PF-[ ]4-GM-[ ]T92-[ ]Determine basic part number from table above. Flaring toolsare available in a number of shank diameters and shanklengths. Select from table below and list correspondingdash number as a suffix to basic part number.Sh an k Diamet er s an d L en g t h 5/8-35/167/8-43/87/8Example: To specify Flaring Die P/N 4-PF-1[?], with 5/16"shank diameter and 7/8" shank length, complete the partnumber with a-3. Completed part number: 4-PF-3.Countersinking Tool 4GC-500Forms C’Sink required for Flush Mounting Grommets.Typical InstallationAdaptors for Countersinking ToolsMay be used to adapt any C’Sinking tool for use in drillchuck.C’Sink ToolThreadAdaptorPart Number5/16-32NEF-2B1/4-28UNF-2BT19T19-1A-57
QUICK OPERATING 1/4-TURN FASTENERS4002 SERIES4002 Series. Stud Assembly InstallationInstalling Stud Into PanelStud Ejector Spring (Optional)4002 Series studs must be used in conjunction with agrommet. (See Page A-51 for grommet selection.)Compress stud assembly spring using Camloc pliersP/N 4P43 as shown. Insert stud through grommet andrelease when cross pin clears. Studs with dash numbersgreater than -15 require retaining rings. These longer studsmay be installed without compressing the stud assemblyspring (pliers not required).Provides full retraction of stud assembly to allow openingand closing of equipment without the possibility of jammingor damage.Retaining RingsPart NumbersMaterialFor use withFlushGrommetsFor use withPlus FlushGrommets4002 SG4002 SNPart No.MaterialMaximumServiceTemperature4002-SWSpring Steel(Cadmium Plated)450 F.4002-SW-SSStainless Steel700 F.Retaining Ring Installation1. To install, place retaining ring on stud with slotaligned over left side of cross pin as shown on figure 1.2. Snap retainingring under cross pin using needlenose pliers, then rotate retaining ring 180 until ringis over right side of cross pin as shown on figures2 and 3.3. To complete installation, snap retaining ring overthe right side of cross pin.4. Completed installation is shown in figure 4.A-58Spring Steel(Cadmium Plated)4002 SGD4002 SND4002 SGF*4002 SNF*RivetHolesPlainDimpledPlain*Ejector P/N 4002 SNF is flat; i.e. no 4" radius bend.Notes: 1. Thru hole in Ejector Spring Part Numbers 4002SN, SND andSNF is formed to allow grommet to seat flush to top surfaceof Ejector Spring.2. When using Stud Ejector Springs, Retaining Ring/Retainedstyle grommets must be used.3. Maximum Service T emperature: 450 F.4. Add .021 to total material thickness “G” when using theseparts. See Page A-61.5. Weight per 100 pieces:Ejector Spring used with Flush Grommet: 1.84 lbs.Ejector Spring used with Plus Flush Grommet: 1.86 lbs.
QUICK OPERATING 1/4-TURN FASTENERS4002 SERIES4002 Series. Sealed Stud andGrommet Installation40S37 Series stud assembly contains an integral sealwhich is usually sufficient where only splash-proofAinstallation is required. For more complete sealing thefollowing procedure should be followed.Grommet Installation1. Select grommet from the table below .2. Prepare panel according to standard procedures.See table below for page reference.3. Install gasket onto grommet.4. Place grommet in prepared holeand complete installationfollowing standard procedure.Gr o m m et /Gas k et Selec t io nGrommetsGasketPart NumberAD i a.GasketMaterialInstallationInstructionsRing Retained:4002-G, H, N, O40G11-3.443.431S ee P agesA-54-A-56Flare Retained:4002-P2-P340G15, 40G1640G11-4.501.489VellumoidGasketMaterial perF e d . S p e c.HH-P-96S ee P ageA-57Stud Installation1. Install gasket P/N 40S39 over stud spring cup.2. Using 4P3 pliers, install stud into grommet followingstandard procedures. (See Page A-58.)3. For studs with dash numbers greater than -15, installretaining ring. For proced ures see Page A-58Notes: 1. Applications using this assembly are limited by the gasket material to 130 F. maximum temperature.2. Add .045 inch to “G” thickness to compensate for gasket thickness. (See Page A-61.)3. 40S37 Stud Assemblies are not available with dash numbers smaller than -4.A-59
QUICK OPERATING 1/4-TURN FASTENERS4002 SERIES4002 Series. Receptacle Installation DataStandard Mounting ReceptaclesTwo piece floating receptaclesSpot weld attachment1. Drill #30 (.1285) diameter pilot hole.2. Drill holes for .125 rivets using drill jig specified.3. Enlarge pilot hole to X diameter .4. Rivet receptacle in place.1. Form through hole to X diameter .2. Place receptacle element into cage.3. Locate receptacle assembly on center and spotweld in place.ReceptacleXD i a.(Ref.)HoleS awR RivetHole Spacing(Ref.)DrillJi g244-22 SeriesStandard Mount.812HS-8121.375T22ReceptacleAssemblyX D i a.(Ref.)R(Ref.)Hole SawAll OtherStandard Mount.688H-6871.00T11/16" Float Versions751, 751E/756W, 757W.6871.00HS-6871/8" Float Versions 701,701E/706W.8121.375HS-812Side Mounting ReceptacleOptional Installation ToolsDrill JigsProvide convenient means for accurately locating rivetholes relative to receptacle mounting hole.Drill JigAT16T221.0001.375Snap-in Receptacle (P/N 40R39-1-1AA)Hole SawsAccurately size mounting holes.Hole Saw Forms Hole Dia.HS-687.687HS-812.812When using hole saw, first drill #30 (.1285) pilot hole.A-60
QUICK OPERATING 1/4-TURN FASTENERS4002 SERIES4002 Series. Ordering Information/Stud Dash Number SelectionTo Select Stud Dash Number1. Stud dash number varies with receptacle used.This information must be known before proceeding.Select receptacle from Pages A-48 through A-50.A2. Determine “G” thickness.Notes:(a)(b)Increase “G” to allow for thickness of paint orother finishes and for the compressed thicknessof any gasket.When selecting stud dash number , “G” must beincreased for the following “Special” conditions.“Special” ConditionsIncrease “G” Thickness4002 Series EjectorSpring installedAdd .021 inchSnap-in Receptacle(P/N 40R 39-1-1AA)installedAllow .020 inch for receptacletop side protrusion.40R8 Series ReceptacleShims installedFor each shim used, add anamount equal to “A” max. shimthickness. (See Page a-48)Plus Flush GrommetsinstalledFor purposes of selecting studdash number only, add “D”max. protrusion of grommet.(See Pages A-51 and A-52)40S37 Stud Assemblyinstalled withsealing gasketsAdd .045 inch3. Locate “G” total thickness in the stud dashnumber table on the following page.4. Then find the corresponding stud dash number inthe column designated for the receptacle selected.How To OrderExample 1.Stud Assembly Used: 4002-[?]S“G” Total Thickness: .220 inchGrommet Used: 4002-0S (Plus Flush Style)Receptacle Used: 40R17-1Required Calculation*: G .029 .220 .029 .249Stud Dash Number Selected From Table: -7Completed Part Number: 4l002-7S*(Plus Flush grommets require that “D” max. dimensionfrom Pages A-51 and A-52 be added to “G” total thicknesswhen determining Stud Dash Number).Example 2.Stud Assembly Used: 40S5-[?]“G” Total Thickness: 1.520 inchGrommet Used: 4002-P2-625 (Flush Style)Receptacle Used: 244-16EStud Dash Number Selected From Table: -51 (See Note 2, Page A-62)Completed Part Number: 40S5-51A-61
QUICK OPERATING 1/4-TURN FASTENERS4002 SERIESStud Dash Number Selection -1.5201.521-1.550Gr o mmet ed St u d s23All 244-16All rec.ex-16Bnot tab.&-16BRat rightAll 5-45-46-46-47-47-48-48-49-49-50-50-5145All 244-16B244-16B-RAll rec.not tab.at -38-38-40-40-42-42-44-44-46-46-48-48-50Gr o mmet les s St u d s67All 244-16All 244-16Bex. 16B244-16B-R&-16BRAll nt Notes: 1.40S37 stud assemblies are not available with dash numbers smaller than -4. 2. If the total thickness “G”is very near the top of the thickness range, selection of the next greater dash number is recommended. For . “G” thicknesseslonger than those tabulated, contact Camloc Products Division. 3. “G” min. thickness specified on Pages. A-51 and A-52may be reduced. .030 inch when column 3 dash numbers apply and .060 inch when column 4 dash numbers apply .A-62
QUICK OPERATING 1/4-TURN FASTENERS4002 SERIES4002 Series.Weights for Flare Retained Grommets(Pounds per 100 pieces. All weights are approximate.)Dat a Tab le 1*Dat a Tab le 2*GrommetDash Numbers40G16-[ ]-140G16-[ ]-240G16-[ ]S40G15-[ ]40G15-[ ]S- 40- 4.46ADat a Tab le 3GrommetDash Numbers4002-P2-[ ]4002-P3-[ ]4002-P4-[ ]4002-P4-[ ]A4002-P4-[ ]B- 187- 250- 312- 375- 4000.480.510.530.560.570.490.520.550.58 0.790.810.840.87 - 437- 500- 625- 750- 812- 875-1000-1062-1125-1250-1375-1500-1562 0.620.670.72 0.780.83 0.890.941.001.05 09 0.920.981.03 1.091.14 1.201.251.301.36 * Data Table Numbers Correspond to those listed on Page A-53.A-63
QUICK OPERATING 1/4-TURN FASTENERS 4002 SERIES The 4002 Series fasteners utilize a variety of grommets designated to reinforce the panel for added strength. Certain 4002 series 1/4-turn fasteners are qualified to MIL-F-5591* specifications for sizes 5 and 7. To Order a Co
I4 Compressor 2 ready I5 Compressor 3 ready I6 Compressor 4 ready I7 MOS activated Q1 Turn on compressor 1 Q2 Turn on compressor 2 Q3 Turn on compressor 3 Q4 Turn on compressor 4 Q6 Turn off compressor 1 Q2 Turn off compressor 2 Q7 Turn off compressor 3 Q8 Turn off compr
investigate three left-turn control types including direct left-turn (DLT), right-turn followed by U-turn (RTUT), and U-turn followed by right-turn (UTRT). The geometric characteristics of each intersection are shown in Table I. In order to evaluate each left-turn control type, many scenarios were created by changing certain traffic parameters.
EZIZ Site: One-stop shop for all My Turn Resources (Link) YouTube Channel: My Turn Training Videos (Link) Video: My Turn Introduction Quick Sheet: Onsite Support Staff FAQs Quick Sheet: Tips & Tricks for using My Turn PowerPoint: End-to-End Process Flow *All
LOGIQ e GE Healthcare. 2 LOGIQ e Quick Card The Quick Card is a quick reference to operation. Please refer to Basic User Manual for detailed information. Control Panel 1 15 14 6 7 13 12 5 11 4 10 3 9 2 8. LOGIQ e Quick Card 3 The Quick Card is a quick reference to operation. Please refer to Basic User Manual for detailed information.
LOGIQ e Quick Card 10 11 LOGIQ e Quick Card The Quick Card is a quick reference and not does not replace the User Manual. Please refer to the Basic User Manual for complete safety and operation information. The Quick Card is a quick reference and not does not replace the User Manual. Please refer to the Basic User Manual for complete safety
4. Face police car, turn clockwise 3 right angles. 5. Face school bus, turn anticlockwise 1 right angle. 6. Face bicycle, turn anticlockwise 2 right angles. 7. Face thief, turn clockwise 1 right angle. 8. Face police car, turn anticlockwise 2 right angles. 9. Face thief, turn clockwise 3 right angles
Chapter 6 Geometric Design Page 6 of 12 Figure 5: Parallel type right-turn deceleration lane—for major or minor right-turn lanes. Figure: Taper type right-turn deceleration lane—for major right-turn lanes. Minor Right-Turn Lane Design A minor right-turn lane provides for deceleration from 30 mph on the mainline to the speed
Ketiga, hasil belajar Sejarah Kebudayaan Islam terlihat pada motivasi, aktivitas dan kreativitas siswa. Nilai akhir pembelajaran 70% di atas Kriteria Ketuntasan Minimum dan 30 % di bawah Kriteri Ketuntasan Minimum. Kata Kunci: e-learning, e-mail, upload, online, google clasrrom. Abstrac: This study aims to analyze the implementation of e-learning at Marasah Tsanawiyah. The study was conducted .
