Installation Instructions - Belmont Dental Equipment Company
INSTALLER’S GUIDEBDS-0050: SWING MOUNTED ASSISTANT VAC PAC FORBEL-50 AND BEL-20N DENTAL CHAIRSLocation for all the incoming utilities should be in accordance with the cabinetinstallation instructions.BDS-0050CAUTIONTools Required:Phillips Screwdriver, 1/8” & 5.5 mm Hex Key Wrench1. Remove plastic dome casting cover from chair.Gently pry off decorative white plastic screw headcovers. Please refer to figure 1 & 2. Remove (4)Phillips head screws and plastic countersink washers(one from each side and two from the top surface).Caution must be used in this step to avoid possibleinjury and damage to part.NOTE: Seat may be unlocked & rotated for improvedscrewdriver access to screws on top surface.PHILLIPSSCREWDRIVERFigure 1. Remove caps and screws from side of domecasting cover. (Right side/Front view)Figure 2. Removing top screw, dome casting cover.(Rear view)2. Remove rear access panel from the dome casting cover. Please refer to figure 3 & 4.Using a Phillips screwdriver, remove small screw located inside of the dome casting cover. Remove rear mount accesspanel cover. Access panel cover is not needed again unless Vac Pac is removed at a future time.Figure 3. Removing rear access panel screw.(Screw located inside of the dome casting cover).A DIVISION OF TAKARA BELMONT USA, INC.101 Belmont Drive Somerset, NJ 08873Phone: (800) 223-1192 Fax: (732) 356-1035Figure 4. Rear access panel with cover removed.Page 1 of 609-23-16 Rev. -0097-370
INSTALLATION & ASSEMBLY (BELMONT BDS-0050)3. Attaching the Vac Pac to the chair. Please refer to figure 5, 6 & 7.5.5 mm HEX1/8” HEXFigure 5. Remove the umbilical retainingclamp from the bottom of the Vac Pacmounting bracket.Figure 6. Slide plastic dome casting coverover the end of the mounting bracketand arm linkage.Figure 7. Secure the mounting bracketto the chair using the (3) M8 cap headscrews provided.4. Re-attach the dome casting cover.Slide the dome casting cover back over arm linkage and mounting bracket andre-attach to the chair using the hardware removed in step 1.5. Re-attach the umbilical retaining clamp.Re-attach the umbilical and clamp to the bottom of the Vac Pac mounting bracket,using the screw removed in step 3 (Figure 5).6. Routing the Vac Pac umbilical underneath the seat area. Please refer to figure 8, 9 & 10.From the back side of the chair, feed the umbilical upward and underneath seat area,along the outside of the spring area.Route the umbilical upward and underneath seat area. (Figure 8 & 9).Figure 10. Top view of seat area. Left is back ofseat / Right is front of seat.Figure 8. View is from rear of chair.Figure 9. View is from rear of chair.Page 2 of 6For Bel-20N Chairs: Please refer to figure 10.Pull the umbilical upward and route along theoutside of the spring area.09-23-16 Rev. -0097-370
INSTALLATION & ASSEMBLY (BELMONT BDS-0050)Bel-50 Chairs: Please refer to figure 11.Figure 11. Pull the umbilical upward androute along the outside of the spring area.(View shown: front/right)Use Phillips screwdriver to remove screws from plastic seat housing cover shroud onone side of the seat. Please refer to figure 12, 13 & 14.Figure 12. Remove screw underneaththe plastic cover in front of the chair.(One side only).Figure 13. Remove screw on the outside plastic cover, adjacent to armrestcasting. (One side only).Page 3 of 6Figure 14. Remove screw from innerplastic cover, adjacent to armrest casting. (One side only).09-23-16 Rev. -0097-370
INSTALLATION & ASSEMBLY (BELMONT BDS-0050)7. Routing the Vac Pac umbilical into the umbilical duct hose. Please refer to figure 15 & 16.Pull umbilical out through the notched cut-out, in front of the seat. Vac Pac umbilical and deliverysystem umbilical are both fed together into the outer umbilical duct hose and connected to the J-box.Figure 15. Vac Pac umbilical tubing exits throughnotched cut-out in front of the seat.Figure 16. Delivery system umbilical shown herein black.8. Connections.Vac Pacs are shipped without Air and Water Regulator/Filter/Valve assemblies or J-Box cover and frame. Syringeair, syringe water, outlet water supply should be connected to delivery system floor utilities. Connect vacuum drainage line to suction source in floor.9. Verification.Verify that all connections to Air, Water and Vacuum are leak-free. Verify that HVE and SE suction are adequate,syringe air and water are satisfactory and that the adjustable water outlet is functional.Page 4 of 609-23-16Rev. -0097-370
INSTALLATION & ASSEMBLY (BELMONT PARTNUMBERDESCRIPTIONQTY.V1513GPlastic Knob, Grey (only)100162900010383Bumper, Belmont20020092200236160011026Washer, 1/4 ID x 9/16 OD x .02 THKDESCRIPTIONQTY.Quick Disconnect, 1/4 " ID1Solids Collector, 2 - 1/8” ODCover, Vacuum Arm110011106Spacer, 1/4"10023786Base Plate, Vacuum Arm10012033Screw, 6-32 x .625, Button Socket, SS4FASA85B0Assistant's Holder, Belmont1001212810-32 x 5/16 socket set sup pt1V1511GNeedle Control Valve, WITH Knob1001214410-32 x 3/8 socket cap screw 18-821100130Flow Restrictor100122631/4-20 x 1 1/2 Button Socket Head Screw18-81S1100HVE, Universal W/QD1S1200SE W/ QD100122781/4-20 x 3/16 Socket set screw, brass tip1D3439Syringe, Quick Clean, DCI10012615Screw, 6-32 x 3/8" Button Socket CapScrew, SS51110623Bent Arm Weldment, Upper, Rear SwingMount1Barb, 10-32 X 1/811110793Arm, Assistant Instrument Holder111400017Plug HVE Port, Central Vacuum1P1053P1062Sleeve, 1/4", Plastic (Not Shown above)P1856Plastic Elbow, 1/8" ID Barb, 10-3221400133Locking CV Ass'y 5/8 Rear Drain1P1055Washer, Plastic, 10-32360130101/4-20 Nylon Insert Locknut1BDS-0050 Rear Assistants Vac Pac (Upper Arm Assembly)Scale: 1:4.25Page 5 of 609-23-16Rev. -0097-370
INSTALLATION & ASSEMBLY (BELMONT 013012000603700121340012389PART NUMBERDESCRIPTIONQTY.0006037Pivot Bushing2Spacer, Nylon600110270011062001104100110413/8 in SAE Flat Washer, Zinc Roh10011062Washer, 2 x 3/8 x .031, Nylon30011063Plastic Washer1001213410-32 x 5/8 Butt Soc Cap SS20012136Screw, 10-32 x 3/8" Button Socket Cap, SS100122781/4-20 x 3/16 Socket set screw, brass tip100123603/8-16 x 1 1/2 Flat Socket Cap Screw100123893/8-16 x 3 Hex Cap Screw Zinc10012718M8 x 30mm, Socket Cap Screw, Painted30016004Sleeve, 1/4", Plastic100190871" Heavy Duty Cable Clamp11100130Flow Restrictor11110438Swing Link11110594Mounting Bracket, BDS-005011110963Bent Arm, Lower, Rear Swing11110964Collar, Pivot Screw11400133Locking CV Ass'y 5/8 Rear Drain160130123/8-16 Thin Nylon Insert Locknut2BDS-0050 Rear Assistants Vac Pac (Lower Arm Assembly)Scale: 1:4.25Page 6 of 609-23-16Rev. -0097-370
BEL-50 AND BEL-20N DENTAL CHAIRS Location for all the incoming utilities should be in accordance with the cabinet installation instructions. BDS-0050 A DIVISION OF TAKARA BELMONT USA, INC. 101 Belmont Drive Somerset, NJ 08873 Phone: (800) 223-1192 Fax: (732) 356-1035 Tools Required:
DENTAL SCIENCES 1 Chapter 1 I Dental Assisting— The Profession 3 The Career of Dental Assisting 4 Employment for the Dental Assistant 4 The Dental Team 6 Dental Jurisprudence and Ethics 12 Dental Practice Act 12 State Board of Dentistry 12 The Dentist, the Dental Assistant, and the Law 13 Standard of Care 13 Dental Records 14 Ethics 14
Cigna Dental Care DMO Patient Charge Schedules 887394 09/15 CDT 2016 Covered under Procedure Code1 Dental Description and Nomenclature Cigna Dental 01 and 02 PCS Cigna Dental 03 PCS Cigna Dental 04 PCS Cigna Dental 05 PCS Cigna Dental 06 PCS Cigna Dental 07 PCS Cigna Dental 08 PCS Chair Time Per Y/N Minutes Code # (if different) Y/N Code # (if .
1 manatee dr sunrise lakes conyers 1 milam dr entrance sign left side ellenwood 1 simmons way poole's mhp ellenwood 10 aiken way lt 33 cotton fi covington 10 alley cir lt 78f the fall covington 10 amberwood ct lt 41 crown for mcdonough 10 belmont cv ll lt 109 belmont covington 10 belmont farms dr belmont farms s ellenwood
is a detailed list of dental services provided by a dental office and given to Delta Dental for payment. Delta Dental means Delta Dental Plan of Michigan, Inc., a service provider for dental benefits under the Michigan Dental Program. Delta Dental ID Card is a permanent (not monthly) card. We send
Mid-level dental providers, variously referred to as dental therapists, dental health aide therapists and registered or licensed dental practitioners, work as part of the dental team to provide preventive and routine dental services, such as cleanings and fillings. Similar to how nurse practitioners work alongside physicians, mid-level dental .
Such dentists or dental staffs should instruct and/or assist the patients to approach to and leave . please contact Takara Belmont offices or your dealers. Do not disassemble or attempt to repair. . Attempts at disassembly, repair or modifications may lead to abnormal operation and accidents. In case
Jun 14, 2016 · active duty Soldiers treated at any of five dental clinics on Fort Bragg. These clinics included Davis Dental Clinic, Joel Dental Clinic, LaFlamme Dental Clinic, Pope Dental Clinic, and Smoke Bomb Hill Dental Clinic. For each appointment the appointment type, date, and dental wellness class
to AGMA 9 standard, improved the quality and performance of the QE range. Today, the QE Vibrator not only meets industry expectations, but will out-perform competitive models when correctly selected and operated in line with the information given in this brochure. When a QE Vibrator is directly attached to a trough it is referred to as a “Brute Force” design. It is very simple to calculate .
