Introduction Thismanualidentifiespotentialhazardsandhassafety
Form No. 3400-717 Rev A22inRecycler Lawn MowerModel No. 20372—Serial No. 316000001 and UpModel No. 20374—Serial No. 316000001 and UpOperator's ManualReplacement parts are available from an Authorized Service Dealer or at www.shoptoro.com.IntroductionThis rotary-blade, walk-behind lawn mower is intended tobe used by residential homeowners. It is designed primarilyfor cutting grass on well-maintained lawns on residentialproperties. It is not designed for cutting brush or foragricultural uses.Read this information carefully to learn how to operate andmaintain your product properly and to avoid injury andproduct damage. You are responsible for operating theproduct properly and safely.You may contact Toro directly at www.Toro.com for productand accessory information, help finding a dealer, or to registeryour product.Whenever you need service, genuine Toro parts, or additionalinformation, contact an Authorized Service Dealer or ToroCustomer Service and have the model and serial numbers ofyour product ready. Figure 1 identifies the location of themodel and serial numbers on the product.Figure 21. Safety alert symbolThis manual uses 2 words to highlight information.Important calls attention to special mechanical informationand Note emphasizes general information worthy of specialattention.WARNINGCALIFORNIAProposition 65 WarningThis product contains a chemical or chemicalsknown to the State of California to cause cancer,birth defects, or reproductive harm.The engine exhaust from this productcontains chemicals known to the State ofCalifornia to cause cancer, birth defects,or other reproductive harm.It is a violation of California Public Resource CodeSection 4442 or 4443 to use or operate the engine on anyforest-covered, brush-covered, or grass-covered land unlessthe engine is equipped with a spark arrester, as defined inSection 4442, maintained in effective working order or theengine is constructed, equipped, and maintained for theprevention of fire.G017291Figure 11. Model and serial number plateWrite the product model and serial numbers in the spacebelow:Model No.Serial No. 2015—The Toro Company8111 Lyndale Avenue SouthBloomington, MN 55420This manual identifies potential hazards and has safetymessages identified by the safety alert symbol (Figure 2),which signals a hazard that may cause serious injury or deathif you do not follow the recommended precautions.Register at www.Toro.com.This spark ignition system complies with Canadian ICES-002.The enclosed Engine Owner's Manual is supplied forinformation regarding the US Environmental ProtectionAgency (EPA) and the California Emission ControlRegulation of emission systems, maintenance, andwarranty. Replacements may be ordered through theengine manufacturer.Original Instructions (EN)Printed in the USAAll Rights Reserved *3400-717* A
SafetyNet Torque: The gross or net torque of this engine waslaboratory rated by the engine manufacturer in accordancewith the Society of Automotive Engineers (SAE) J1940.As configured to meet safety, emission, and operatingrequirements, the actual engine torque on this class of mowerwill be significantly lower. Go to www.Toro.com to viewspecifications on your mower model.This machine has been designed in accordance with EN ISO5395:2013 and ANSI B71.1-2012.General SafetyThis product is capable of amputating hands and feet andof throwing objects. Always follow all safety instructions toavoid serious personal injury.ContentsIntroduction . 1Safety . 2General Safety. 2Safety and Instructional Decals . 3Setup . 41 Assembling and Unfolding the Handle . 42 Installing the Recoil-Starter Rope in the RopeGuide. 53 Filling the Engine with Oil. 54 Charging the Battery. 65 Assembling the Grass Bag . 6Product Overview . 7Operation . 8Before Operation . 8Before Operation Safety . 8Filling the Fuel Tank . 8Checking the Engine-Oil Level. 9Adjusting the Handle Height. 9Adjusting the Cutting Height . 9During Operation .10During Operating Safety.10Starting the Engine .10Using the Self-Propel Drive .11Stopping the Engine .11Recycling the Clippings .11Bagging the Clippings .12Side-Discharging the Clippings.13Operating Tips .13After Operation .14After Operating Safety .14Cleaning under the Machine.14Folding the Handle .14Maintenance .16Recommended Maintenance Schedule(s) .16Maintenance Safety.16Preparing for Maintenance.16Replacing the Air Cleaner .17Changing the Engine Oil .17Charging the Battery .18Replacing the Fuse.18Replacing the Blade .19Adjusting the Self-Propel Drive .20Storage .21Preparing the Machine for Storage .21Remove the Machine from Storage.21Using this product for purposes other than its intended usecould prove dangerous to you and bystanders. Read and understand the contents of this Operator’s Manualbefore you start the engine. Ensure that everyone usingthis product knows how to use it and understands thewarnings. Do not put your hands or feet near moving componentsof the machine. Do not operate the machine without all guards and othersafety protective devices in place and working on themachine. Keep clear of any discharge opening. Keep bystanders asafe distance from the machine. Keep children out of the operating area. Never allowchildren to operate the machine. Stop the machine and shut off the engine before servicing,fueling, or unclogging the machine.Improperly using or maintaining this machine can resultin injury. To reduce the potential for injury, comply withthese safety instructions and always pay attention to thesafety-alert symbol, which means Caution, Warning, orDanger—personal safety instruction. Failure to comply withthese instructions may result in personal injury or death.You can find additional items of safety information in theirrespective sections throughout this manual.2
Safety and Instructional DecalsImportant: Safety and instruction decals are located near areas of potential danger. Replace damaged decals.Manufacturer's Mark1. Indicates the blade is identified as a part from the originalmachine manufacturer.94-8072104-79531. Warning—read the Operator's Manual for information on charging the battery; contains lead; do not discard.2. Read the Operator's Manual.133–19001. Read the Operator’s Manual for more information on startingthe engine—1) Insert the key into the ignition; 2) Engage theblade-control bar; 3) Push the key to start the engine.2. Read the Operator’s Manual for more information on stoppingthe engine—1) Release the blade-control bar; 2) Remove thekey from the ignition.117–2718112-88671. Lock2. Unlock3
SetupImportant: Remove and discard the protective plasticsheet that covers the engine.1Assembling and Unfolding theHandleNo Parts RequiredProcedure1. Remove and save the 2 handle knobs and 2 carriagebolts from the handle brackets (Figure 3).131-0894Traction Adjustment1. Attention; read the Operator's Manual—1) Loosen theknob by turning it counter clockwise; 2) Pull the cable(s)away from the engine to decrease the traction, or pushthe cable(s) toward the engine to increase the traction; 3)Tighten the knob by turning it clockwise.Figure 31. Handle knob2. Carriage bolt2. Install the handle ends onto the mower housing so thatthe pin attached to each handle bracket is in the lowerhole of its related handle end (Figure 4).131–45141. Warning—read the Operator's Manual.2. Cutting/dismemberment hazard of hand or foot, mowerblade—stay away from moving parts; keep all guards andshields in place.3. Cutting/dismemberment hazard of hand or foot, mowerblade—disconnect the spark-plug wire and read theinstructions before servicing or performing maintenance.4. Thrown object hazard—keep bystanders a safe distancefrom the machine; stop the engine before leaving theoperating position; pick up any debris before mowing.5. Cutting/dismemberment hazard of hand or foot, mowerblade—do not operate up and down slopes; operate side toside on slopes; look behind you when backing up.Figure 41. Pin42. Handle end
Note: The pins will not show through the holes in thehandle ends when the handle is in the folded position.23. Unfold the handle to the operating position by rotatingit rearward (Figure 5).Installing the Recoil-StarterRope in the Rope GuideNo Parts RequiredProcedureImportant: To start the engine safely and easilywhenever you use the machine, install the recoil-starterrope in the rope guide.Figure 51. Folded positionHold the blade-control bar to the upper handle and pull therecoil-starter rope through the rope guide on the handle(Figure 7).2. Operating position4. Insert the carriage bolt (with the bolt head towardthe inside) through the upper or lower square hole inhandle bracket and the upper hole in the handle end(Figure 6).Figure 71. Recoil-starter rope2. Rope guide3Filling the Engine with OilFigure 61. Handle knobNo Parts Required2. Carriage boltProcedure5. Loosely install the handle knobs onto the carriage bolts.Important: Your machine does not come with oil inthe engine. Before starting the engine, fill the enginewith oil.6. Refer to steps 3 through 5 of Adjusting the HandleHeight (page 9).1. Move the machine to a level surface.2. Remove the dipstick (Figure 8) and pour about 3/4 ofthe crankcase capacity of oil into the oil-fill tube.Note: Max. fill: 0.53 L (18 oz), type: SAE 30 or SAE10W-30 detergent oil with an API service classificationof SF, SG, SH, SJ, SL, or higher.5
4Charging the BatteryNo Parts RequiredProcedureElectric-start model onlyRefer to Charging the Battery (page 18).G0173235Figure 81. The oil level is at itsmaximum.3. The oil level is toolow—add oil to thecrankcase.Assembling the Grass Bag2. The oil level is toohigh—remove oil fromthe crankcase.No Parts Required3. Wipe off the dipstick end with a clean cloth.Procedure4. Insert the dipstick into the oil-fill tube, but do notscrew it in.1. Slip the grass bag over the frame as shown in Figure 9.5. Remove the dipstick and read the oil level on thedipstick (Figure 8).1 If the oil level is too low, add a small amount ofoil slowly to the oil-fill tube, and then repeat steps3 through 5 until the oil level on the dipstick iscorrect. If the oil level is too high, drain the excess oil untilthe oil level on the dipstick is correct. To drain theexcess oil, refer to Changing the Engine Oil (page17).g027257Important: If the oil level in the crankcase istoo low or too high and you run the engine,you may damage the engine.26. Install the dipstick securely.3Figure 9Important: Change the engine oil after the first 5operating hours; change it yearly thereafter. Referto Changing the Engine Oil (page 17).1. Handle3. Grass bag2. FrameNote: Do not slip the bag over the handle (Figure 9).2. Hook the bottom channel of the bag onto the bottomof the frame (Figure 10).6
Product OverviewFigure 11g027258Figure 101. Handle8. Cutting-height lever (4)2. Blade-control bar9. Spark plug3. Adjustment knob for theself-propel drive10. Side-discharge deflector4. Ignition button(electric-start model only)11. Bag-on-demand lever5. Oil fill/dipstick12. Handle knob (2)6. Fuel-tank cap (not shown) 13. Recoil-start handle7. Air filter3. Hook the top and side channels of the bag onto the topand sides of the frame, respectively (Figure 10).Figure 121. Grass bag2. Side-discharge chute73. Battery charger(electric-start model only)
Filling the Fuel TankOperation For best results, use only clean, fresh (less than 30 daysBefore Operationold), unleaded gasoline with an octane rating of 87 orhigher ((R M)/2 rating method). Oxygenated fuel with up to 10% ethanol or 15% MTBEBefore Operation Safetyby volume is acceptable. Ethanol: Gasoline with up to 10% ethanol (gasohol)General Safetyor 15% MTBE (methyl tertiary butyl ether) by volumeis acceptable. Ethanol and MTBE are not the same.Gasoline with 15% ethanol (E15) by volume is notapproved for use. Never use gasoline that contains morethan 10% ethanol by volume, such as E15 (contains 15%ethanol), E20 (contains 20% ethanol), or E85 (containsup to 85% ethanol). Using unapproved gasoline maycause performance problems and/or engine damagewhich may not be covered under warranty. Become familiar with the safe operation of the equipment, operator controls, and safety signs.Check that all guards and safety devices, such as deflectorsand/or grass catcher, are in place and working properly.Always inspect the machine to ensure that the blades,blade bolts, and cutting assembly are not worn ordamaged.Inspect the area where you will use the machine andremove all objects that the machine could throw.Adjusting the cutting height may bring you into contactwith the moving blade, causing serious injury.– Shut off the engine and wait for all moving parts tostop.– Do not put your fingers under the housing whenadjusting the cutting height. Do not use gasoline containing methanol. Do not store fuel either in the fuel tank or in fuelcontainers over the winter unless a fuel stabilizer is used. Do not add oil to gasoline.Fill the fuel tank with fresh unleaded regular gasoline from amajor name-brand service station (Figure 13).Important: To reduce starting problems, add fuelstabilizer to the fuel all season, mixing it with gasolineless than 30 days old.Fuel SafetyDANGERFuel is extremely flammable and highly explosive.A fire or explosion from fuel can burn you andothers and can damage property. To prevent a static charge from igniting the fuel,place the container and/or machine directly onthe ground before filling, not in a vehicle or onan object. Fill the fuel tank outdoors, in an open area, whenthe engine is cold. Wipe up any fuel that spills. Do not handle fuel when smoking or around anopen flame or sparks. Store fuel in an approved container and keep itout of the reach of children.G017304Figure 13WARNINGFuel is harmful or fatal if swallowed. Long-termexposure to vapors can cause serious injury andillness. Avoid prolonged breathing of vapors. Keep your hands and face away from the nozzleand the fuel-tank opening. Keep fuel away from your eyes and skin.8
Checking the Engine-Oil LevelAdjusting the Handle HeightService Interval: Before each use or dailyYou can raise or lower the handle in 1 of 2 positions that ismore comfortable for you (Figure 15).Max. fill: 0.59 L (20 oz), type: SAE 30 or SAE 10W-30detergent oil with an API service classification of SF, SG, SH,SJ, SL, or higher.1. Move the machine to a level surface.2. Remove the dipstick (Figure 14).Figure 151. Loosen both handle knobs until you can push thesquare edges of the carriage bolts out of the squareholes in the handle brackets.G0173232. Push the knobs until they are loose.Figure 141. The oil level is at itsmaximum.3. Move the handle to the upper or lower height position.3. The oil level is toolow—add oil to thecrankcase.4. Pull the knobs until the square edges of each carriagebolt fits into its related square hole.2. The oil level is toohigh—remove oil fromthe crankcase.5. Tighten the handle knobs as tight as you can.Adjusting the Cutting Height3. Wipe off the dipstick end with a clean cloth.Adjust the cutting height as desired. Set the front wheels tothe same height as the rear wheels (Figure 16).4. Insert the dipstick into the oil-fill tube, but do notscrew it in.Note: To raise the machine, move the front cutting heightlevers rearward and the rear cutting height levers forward.To lower the machine, move the front cutting height leversforward and the rear cutting height levers rearward.5. Remove the dipstick and read the oil level; refer toFigure 14. If the oil level is too low, add a small amount ofoil slowly to the oil-fill tube, and then repeat steps3 through 5 until the oil level on the dipstick iscorrect. If the oil level is too high, drain the excess oil untilthe oil level on the dipstick is correct. To drain theexcess oil, refer to Changing the Engine Oil (page17).Important: If the oil level in the crankcase istoo low or too high and you run the engine,you may damage the engine.6. Install the dipstick securely.9
Use extreme care when approaching blind corners,shrubs, trees, or other objects that may block your view. Watch for holes, ruts, bumps, rocks, or other hiddenobjects. Uneven terrain could cause a slip-and-fallaccident. Stop the machine and inspect the blades after striking anobject or if there is an abnormal vibration in the machine.Make all necessary repairs before resuming operation. Before leaving the operating position, shut off the engine,remove the key, and wait for all moving parts to stop. If the engine has been running the muffler will be hot andcan severely burn you. Keep away from the hot muffler. Check the grass catcher components and the dischargeguard frequently and replace them with the manufacturer’srecommended parts when necessary. Use accessories and attachments approved by the TheToro Company only.g027908Figure 161. Raise the machineSlope Safety2. Lower the machine Mow across the face of slopes; never up and down. Useextreme caution when changing direction on slopes.Note: The cutting height settings are 25 mm (1 inch); 35 mm(1-3/8 inches); 44 mm (1-3/4 inches); 54 mm (2-1/8 inches);64 mm (2-1/2 inches); 73 mm (2-7/8 inches); 83 mm (3-1/4inches); 92 mm (3-5/8 inches); and 102 mm (4 inches). Do not mow on excessively steep slopes. Poor footingcould cause a slip-and-fall accident. Do not mow near drop-offs, ditches, or embankments.You could lose your footing or balance.During OperationStarting the EngineDuring Operating Safety1. Hold the blade-control bar against the handle (Figure17).General Safety Wear appropriate clothing, including eye protection;slip-resistant, substantial footwear; and hearingprotection. Tie back long hair, secure loose clothing, anddo not wear jewelry. Do not operate the machine while ill, tired, or under theinfluence of alcohol or drugs. The blade is sharp; contacting the blade can result inserious personal injury. Shut off the engine and wait forall moving parts to stop before leaving the operatingposition. When you release the blade-control b
FormNo. 3400-717RevA 22inRecycler LawnMower ModelNo.20372—SerialNo.316000001andUp ModelNo.20374—SerialNo.316000001andUp Operator'sManual .
Advertise Monetize CPS 소개서 TNK CPS Introduction 매체소개서 Monetize Introduction About Us TNK Factory Introduction 회사소개서 DSP 소개서 TNK DSP Introduction 퍼포먼스 소개서 Performance Introduction 코드뱅크 소개서 Codebank Introduction TNK Factory는 안전하고 빠르며 쉬운 플랫폼입니다.
An Introduction to Modal Logic 2009 Formosan Summer School on Logic, Language, and Computation 29 June-10 July, 2009 ; 9 9 B . : The Agenda Introduction Basic Modal Logic Normal Systems of Modal Logic Meta-theorems of Normal Systems Variants of Modal Logic Conclusion ; 9 9 B . ; Introduction Let me tell you the story ; 9 9 B . Introduction Historical overview .
Partie 1 : Introduction et fonctions 1-1-1 Section 1 : Introduction Surveillance STEPS de l'OMS Section 1: Introduction Présentation générale Introduction Cette section constitue une introduction au Manuel de l'OMS pour la surveillance STEPS. Objectif L'objectif du Manuel est de proposer des lignes directrices et de fournir des
1.1 Introduction 1.2 Context 1.3 Purpose and scope 1.4 Language and terms Chapter 1: Introduction to essential health services 1.1 Introduction 1.2 Purpose & scope 1.3 Language and terms Chapter 1: Introduction to essential justice and policing services 1.1 Introduction 1.2 Purpose & scope 1.3 Language and terms Chapter
(Text from Modern Biology, Holt, Rinehart, and Winston) 1 Chapter Eighteen (Introduction to Ecology)Chapter Eighteen (Introduction to Ecology) SECTION ONE: INTRODUCTION TO ECOLOGYSECTION ONE: INTRODUCTION TO ECOLOGYONE: INTRODUCTION TO ECOLOGY EcologyEcologyEcology is the study
General introduction to Unreal Engine - 3 days 100.1 Introduction to Unreal Engine (self-paced learning video) 1. 100.2 Quick Start: Your First Project in Unreal Engine 2. 101.1 Materials - Introduction 3. 103.1 Lighting - Introduction 4. 102.1 Blueprint - Introduction 5. 102.2 Blueprint - Introduction to UMG and Creating Simple User .
CSC266 Introduction to Parallel Computing using GPUs Introduction to Accelerators Sreepathi Pai October 11, 2017 URCS. Outline Introduction to Accelerators GPU Architectures . An Evaluation of Throughput Computing on CPU and GPU" by V.W.Lee et al. for more examples and a comparison of CPU and GPU. Outline Introduction to Accelerators GPU .
An Introduction to Random Field Theory Matthew Brett , Will Penny †and Stefan Kiebel MRC Cognition and Brain Sciences Unit, Cambridge UK; † Functional Imaging Laboratory, Institute of Neurology, London, UK. March 4, 2003 1 Introduction This chapter is an introduction to the multiple comparison problem in func-
