MUSTANG FLOOR - Fender
MUSTANG FLOORADVANCED OWNER'S MANUALBYFENDER
MUSTANG FLOORcustomize the Mustang Floor in ways not available from theMustang Floor alone. Please download the latest version ofFender FUSE, free of charge from fuse.fender.com.ContentsGetting Started! . . . . . . . . . . . . . . . . 2Data Wheel . . . . . . . . . . . . . . . . . . 2Footswitch Modes . . . . . . . . . . . . . . . 3Tap/Tuner . . . . . . . . . . . . . . . . . . . 3Amplifier Menus . . . . . . . . . . . . . . . . 4Effects Menus . . . . . . . . . . . . . . . . . 4Data WheelTurn the big DATA WHEEL to select presets in play mode(press the EXIT button, if lit, to return to play mode):Expression Pedal . . . . . . . . . . . . . . . 5EXP-1 and MS-4 . . . . . . . . . . . . . . . . 6Saving Presets . . . . . . . . . . . . . . . . . 7Utility Menus . . . . . . . . . . . . . . . . . 7Output Jacks . . . . . . . . . . . . . . . . . . 8Aux/Phone Jacks . . . . . . . . . . . . . . . . 8Insert Loop . . . . . . . . . . . . . . . . . . . 9USB Port . . . . . . . . . . . . . . . . . . . . 9MIDI . . . . . . . . . . . . . . . . . . . . . . 9Press the DATA WHEEL to see basic information about the currentpreset, such as the current amplifier model and the effectsassigned under each of the four effect categories:Factory Restore & Firmware Update . . . . . . 9FAQ . . . . . . . . . . . . . . . . . . . . . . 9MIDI Appendix . . . . . . . . . . . . . . .10Getting Started!INSERT LOOPSENDRETURNAUX INPHONESUNBALANCED OUTRLLEVELRXLR OUTLGROUNDLIFTUSBEXP-1/MS-4MIDIOUTPush to view the Preset Information screenPOWERINPEDALIINPUTPEDAL034521The basic Mustang Floor setup:1. Plug the supplied power adapter into a grounded outlet.Press the DATA WHEEL a second time to see where each effect islocated in the guitar signal processing path:x2PEDAL2. Press the POWER switch to the "1" position to turn the MustangFloor on.3. Plug your guitar into the INPUT jack.4. Connect the input of your guitar amplifier or PA system to theL UNBALANCED OUT jack –OR– plug your headphones into thePHONES jack.5. Turn the LEVEL knob to at least halfway up.PEDALPush twice to view the Signal Path screenYou can change the order of effects in the signal path to createunique sounds using Fender FUSE software.The LEVEL knob controls the output level of all the analogoutputs on the Mustang Floor, including the UNBALANCEDOUT jacks, the XLR OUT jacks and the PHONES jack.6. Turn on your PA system or guitar amplifier –OR– put on yourheadphones and start exploring the Mustang Floor!7. Be sure to power off your amplifier (or PA) before poweringdown the Mustang Floor.The Mustang Floor is fully integrated with Fender FUSE software which allows you to configure and operate theMustang Floor with ease from your computer. You can useFender FUSE to download free presets from Fender artists;backup and restore presets for different occasions; and2The DATA WHEEL has many functions! Enter anyedit mode by pressing one of the buttons belowthe screen and the DATA WHEEL is used to navigateand edit in the menu currently being displayed.Depending on the menu, you will press or turn theDATA WHEEL to select items and adjust settings,as described in this manual and shown on screen.Using the DATA WHEEL is intuitive, but if you everget lost, just press EXIT to return to play mode.
MUSTANG FLOORFootswitch ModesTap / TunerPress the MODE button to switch between PRESET andFX SELECT modes:PRESETMModeU S TA N GFLOORUPPRESET / FX SELECTSelect Preset BanksFLOOR2M U S TA N G Tap in delay time or modulation rate effect settings Activate the on-board guitar tunerTAP/TUNERTMIn PRESET mode the green LED lights up and thebottom five footswitch buttons (0 5, 1 6, 2 7, 3 8, 4 9)are used to select presets from the current bank offive presets. Press the BANK/PRESET buttons to selectdifferent banks of five presets to choose from, thenMODEBANKpress one of the numberedfootswitch buttonsTAP/TUNERtoselect a preset from the bank as displayed on screen.1Use the TAP / TUNER button to:TM34TAP ButtonWhen either a delay or modulation effect is active, the LED next tothe TAP/TUNER button will blink in sync with the effect time/ratesetting (modulation rates can have up to 12 second intervals andthe LED may blink infrequently). If both a delay and modulationeffect are active simultaneously, the LED will blink in sync with thedelay effect and the TAP/TUNER button will only control the delaytime setting (you can bypass the delay effect temporarily if youwant to use the TAP/TUNER button to set the modulation OLD TO EDIT5You can use the effect settings menus or Fender FUSE to setdelay time and modulation rates more precisely.PRESET / FX SELECTMODEINSERTSTOMPMODDELAYTAP/TUNERBANK / PRESET0 51 62 73 84 9INSERTSTOMPMODDELAYREVERB1. Select a delay or modulation effect that causes the TAP/TUNERLED to blink, using the effects menus (see "Selecting Effects"under Effects Menus, page 4).2. Press the TAP/TUNER button rhythmically (twice minimum)in time with the desired interval. If you press the TAP/TUNERbutton only once, the interval will be set to the maximumvalue. You can see the maximum/minimum values for thecurrent effect in the effect settings menu (see page 5).Select Presets from the current BankFX SELECTModeMUS TA N GTMREVERBUsing TAP to set effect time/rate settings:FLOORIn FX SELECT mode the red LED lights up and thebottom five footswitch buttons (INSERT, STOMP,MOD, DELAY, REVERB) are used to select/bypasseffects for the current preset (the INSERT buttonselects/bypasses external effects connected to theMODETAP/TUNERINSERT LOOP jacks).BANKPress the BANK/PRESET buttonsto select presets up or down, one at a time.Watch the actual time/rate TAP values change while you aretapping them in, by opening the effect settings menu!UTILUPPRESET / FX SELECT1INSERTMODESelect2GPresetsFLOORM U S TA NTMSTOMPPRESET / FX SELECTBANK / PRESET34MODDELAYTAP/TUNER0 51 62 73 84 9INSERTSTOMPMODDELAYREVERBSAVETUNER ButtonEXITThe Mustang Floor has a built-in Tuner mode that displays achromatic guitar tuner on screen.AMPSTOMPMODDELAYHOLD TO EDITREVERBPEDALPUSHTo use the Tuner:51. Press and hold the TAP/TUNER button until the Tuner screenappears.2. Strike any single string on your guitar and watch the screen.The note of the string being tuned is displayed along with aREVERBfine tuning needle:Select / bypass EffectsEach FX Select footswitch button will function only when aneffect is assigned to that category for the current preset. SeeEffect Menus on page 4 to choose effects.3. Turn the tuning peg on your guitar until the fine tuning needleindicates the string is in tune, as shown above.4. Press EXIT or TAP/TUNER to exit from the Tuner.3
MUSTANG FLOORAmplifier MenusBypassing Amp SettingsEffects MenusBypassing EffectsYou can turn on or off (bypass) all amp settings thathave been selected for the current preset by pressingthe AMP button. The amp menus contain amplifier modelingselections, and settings for a variety of parameters such as tone,gain, volume, and speaker cabinet simulation.You can turn on or off (bypass) effects that have been selected forthe current preset by pressing the corresponding effect button.The Effect name is highlighted andthe Effect button lights up when aneffect is activeThe Amp name is highlighted andthe AMP button lights up whenAmp settings are activePreset Information screenPEDALEffects can also be bypassed (turned on-off) using thefootswitch buttons when in FX SELECT mode.Preset Information screenEffects that are shown on screen as "–EMPTY–" can not beactivated until an effect has been selected in that category (seeSelecting Effects, below).Selecting Amplifier Models1. Press and hold the AMP button until the amp menu opens.2. Turn the DATA WHEEL to select one of 13 amplifier models:'57 Deluxe'59 Bassman'57 Champ'65 Deluxe ReverbSelecting EffectsPEDALAMP MODELS'65 Princeton'65 Twin ReverbSuper-Sonic (Burn)British '60sBritish '70sBritish '80sAmerican '90sMetal 2000Studio Preamp3. Press EXIT to return to play mode.Adjusting Amplifier Settings1. Press and hold the AMP button until the amp menu opens.2. Press the DATA WHEEL one or more times until the setting thatyou want to adjust is highlighted, then turn the DATA WHEELto adjust the setting. (Press the DATA WHEEL repeatedly toaccess "Page 2" of the amplifier settings. )"PAGE 2" of the Amp settings— Stompbox effects— Modulation effects— Delay effects— Reverb effectsTo select Effects:1. Press and hold one of the four effects buttons to open theeffects menu.2. Turn the DATA WHEEL to select one of the OverdriveWahTouch WahFuzzFuzz Touch WahSimple CompressorCompressorSine ChorusTriangle ChorusSine FlangerTriangle FlangerVibratoneVintage TremoloSine TremoloRing ModulatorStep FilterPhaserPitch ShifterMono DelayMono Echo FilterStereo Echo FilterMultitap DelayPing Pong DelayDucking DelayReverse DelayTape DelayStereo Tape DelaySmall HallLarge HallSmall RoomLarge RoomSmall PlateLarge PlateAmbientArenaFender '63 SpringFender '65 Spring3. Press EXIT to return to play mode.Press the DATA WHEEL repeatedlyto select the next Amp settingYou can hold down the AMP button and turn the DATA WHEELto scroll through settings faster! To de-select a highlightedamp setting, press and hold the AMP button momentarily.3. Press EXIT to return to play mode.4You can switch to a different effects category at any time, evenwhile you are in the effects selection menus, by pressing andholding a different Effects button.Adjusting Effect Settings1. Press and hold one of the four effect buttons (STOMP, MOD,DELAY, REVERB) to open the corresponding effects menu.2. Turn the DATA WHEEL to select the effect you want to workwith.
MUSTANG FLOOR3. Press the DATA WHEEL one or more times until the setting thatyou want to adjust is highlighted, then turn the DATA WHEELto adjust the setting.You can also hold down an Effect button and turn the DATAWHEEL to scroll through settings faster!Pedal MenusPress the PEDAL button to configure the Mustang Floorexpression pedal as well as an external EXP-1 expressionpedal (optional) when connected. Press the PEDALbutton repeatedly to access each of the pedal menus describedbelow. Many menu items are dynamic and only appear under theappropriate conditions. For example, if Expression Behavior modeis set to "off," none of the parameter menus for Expression modewill appear. Likewise, all EXP-1 pedal parameters will appear onlywhen an EXP-1 pedal is connected to the Mustang Floor. Note:EXP-1 menu items are prefaced with "EXP‑1" instead of "FLOOR" onscreen.The current Volume or Expression mode state of the pedalis stored with the current preset when you save a preset. See"Pedal Default" under Utility Menus on page 7 to override.Press the DATA WHEEL repeatedlyto select the next Effect setting4. Press EXIT to return to play mode.You can bypass an effect at any time, even while you are inthe effect settings menus, by pressing the Effect button, orcorresponding footswitch button (when in FX SELECT mode).Expression PedalVOLUME MODE MENUS Volume Enable — (On/Off) Select "On" if you want the pedal tocontrol the master volume level in Volume mode, or select "Off" ifyou want the pedal to be off in Volume mode. Global Volume Heel / Global Volume Toe — (0–100%) Usethese menus to set the master volume level with the heel of thepedal in the fully down position (Heel Volume) and with the toeof the pedal in the fully down position (Toe Volume).The Global Volume Heel and Toe settings are stored globallyand affect all presets. Every other pedal parameter is storedlocally and affects an individual preset.EXPRESSION MODE MENUS Expression Behavior — (Off, Amp, Stomp, Mod, Delay, Reverb, Volume)Select the category that you want to control with the expressionpedal in Expression mode or select "Off" if you want the pedal tobe off in Expression mode.Your Mustang Floor is equipped with a dual-mode expressionpedal. Switch between Volume mode and Expression mode bypressing down hard on the toe end of the pedal. An icon in theupper right corner of the screen displays the current pedal mode."VOLUME OFF" or "EXP OFF" appears if the current pedal modeis set to "off" for the current preset in the Volume Enable orExpression Behavior pedal menus below.Volume mode iconExpression mode iconVolume mode is used to control master volume (or the pedalcan be set to off in Volume mode).Expression mode can be used to control almost any effect oramp parameter on the Mustang Floor (or the pedal can be setto off in Expression mode). Some common uses are to controlthe frequency parameter of a Wah effect or the rate/timeparameter of a modulation or delay effect.You must have an effect selected for the current preset onthe Mustang Floor to make that category of effect becomeavailable for selection in this menu. Expression Parameter — (Variable) Select the parameter thatyou want to control with the pedal in Expression mode. Youroptions will change depending on the category you selectedin the Expression Behavior menu above, and the effect moduleselected for the current preset. Expression Heel / Expression Toe — (Variable) Use these menusto set the level of the active parameter with the heel of the pedalin the fully down position (Heel Setting) and with the toe ofthe pedal in the fully down position (Toe Setting). Your optionswill change depending on the category you selected in theExpression Behavior menu, above. Expression Mode — (Capture, Live) If "Live" is selected, the current pedal position will override the stored preset setting forthe assigned expression pedal parameter when a preset is firstselected. If "Capture" is selected, the pedal is disabled until youmove the pedal after a preset has been selected.5
MUSTANG FLOOR Bypass Effect — (On/Off) Select "On" to bypass the effect currently selected in the Expression Behavior menu when switching thepedal to Volume mode or select "Off" to leave the effect active. Reset Parameter to Preset Value when Switching to VolumeMode — (On/Off) Select "On" to return the Expression ModeParameter to the stored preset value when switching to Volumemode. Select "Off" if you want the parameter be left set to theposition of the pedal when switching to Volume mode.To use the EXP-1 and MS-4 simultaneously, plug the EXP-1 intothe Mustang Floor and then plug the MS-4 into the second jackon the EXP‑1.EXP-1 Expression Pedal (P/N 2301050000)Pedal CalibrationOccasionally it may become necessary to calibrate the MustangFloor's expression pedal and/or an EXP-1 expression pedal connected to the Mustang Floor, to reset the parameter range of thepedal(s) to ensure consistent performance.To calibrate the expression pedal and EXP-1 pedal:1. (Optional) Plug an EXP-1 pedal into the "EXP-1 / MS-4" jack onthe back of the Mustang Floor using the included cable.2. Turn the Mustang Floor off.3. Press and hold the UTIL button on the Mustang Floor whileturning the Mustang Floor back on. Continue holding the UTILbutton down until it is no longer illuminated.4. Rock the Mustang Floor expression pedal (and the EXP-1, ifconnected), through the full range of motion between heeland toe positions.5. The Mustang Floor expression pedal and the EXP-1, if connected, have been calibrated!Configure the EXP-1 expression pedal through the pedal menus(see Pedal Menus, page 5). The EXP-1 only functions in Expressionmode when connected to the Mustang Floor. The green LED indicates when the EXP-1 pedal is powered on and the red LED indicates whether Expression mode is currently enabled.MS-4 Four-Button Footswitch (P/N 0080996000)The MS-4 footswitch display and LEDs show you much of the sameinformation as the Mustang Floor screen, so you can for example,tune your guitar and select presets by watching the footswitchwithout ever looking at the screen onboard the Mustang Floor!The MS-4 allows you to: Select Quick Access presets (QA1/QA2/QA3)Pedal Tension Select presets (up/down/bank)Occasionally it may become necessary to adjust the tension of theaxle nut on the expression pedal to increase or decrease the easeof pedal movement. Activate the Tuner Bypass effectsTo adjust pedal tension:Pry off the circular "F" cap from the right side of the pedal with asmall flat blade screwdriver, then use a 10 mm socket wrench toadjust the axle tension. Do not over-tighten the axle nut to avoiddamaging the pedal assembly.10 mmThe footswitch has three modes that are identified by the threeLEDs labeled MODE 1, MODE 2 and MODE 3. The footswitch alsohas a Tuner mode which is indicated when all of the mode LEDsare off.To switch between modes, press the MODE button. To activateTuner mode, press and hold the MODE button.EXP-1 & MS-4Your Mustang FloorMIDIPOWER gives you the option of adding anOUTINexternalEXP-1expression pedal and an MS-4 fourbutton footswitch for additional flexibility. Both theEXP-1 and MS-4 can be connected together through theEXP-1 / MS-4 jack on the back of the Mustang Floor.EXP-1/MS-4I0USB6 Mode 1—Select one of three Quick Access presets using the buttons labeled: QA1 / QA2 / QA3 (in line with the MODE 1 LED). Thenumber of the preset will appear in the display of the footswitch.You can assign any preset to be a Quick Access preset in theutility menus. (see Utility Menus, page 7). Mode 2—Select presets down/up, or in banks of 10, using thebuttons labeled: DOWN / UP / BANK (in line with the MODE 2LED). The number of the preset will appear in the display of thefootswitch.
MUSTANG FLOOR Mode 3—Bypass the Stompbox, Modulation or Delay effects,using the buttons labeled: STOMP / MOD / DELAY (in line withthe MODE 3 LED). The footswitch button LEDs indicate theeffects that are active. Tuner Mode—Press and hold the MODE button to activate theTuner. The screen on the Mustang Floor and the footswitch bothdisplay tuner information. The footswitch will display the nearestnote and the button LEDs will indicate sharp and flat. "In tune" isindicated when the green LED below the footswitch display lightsup. Press any footswitch button to exit Tuner mode.Saving PresetsYour Mustang Floor gives you the powerful ability to save everysetting on the unit as part of a preset. When you select a preset,every effect setting, amp setting and expression pedal parameteris instantly recalled to your pre-programmed settings.The SAVE button will light up red when you edit anysetting on the Mustang Floor. This indicates that youhave temporarily modified the current preset. You can undo yourmodifications simply by selecting a different preset and then backagain to the preset you started from.The EXIT button will not cancel temporary changes to thecurrent preset. Only by selecting a different preset using theDATA WHEEL, Footswitch, or Fender FUSE, will your temporarychanges be erased.To save your own custom presets:1. To save a custom preset, first modify an existing preset bychanging any setting(s) that you choose.2. Press the SAVE button. The SAVE and EXIT buttons should lightup. You can press EXIT at this point to cancel the save process.3. Turn the DATA WHEEL to select a preset destination tooverwrite.4. Press the DATA WHEEL if you want to edit the name ofyour new preset. Use the soft-key buttons to perform thecorresponding functions shown along the bottom of thescreen. Turn the DATA WHEEL to select characters.Utility MenusPress the UTIL button to activate the utility menus.Press the UTIL button repeatedly to step through eachof the utility menus. Turn the DATA WHEEL to make selections. AllUtility menu settings are stored globally and affect all presets. Someof the descriptions below cover multiple menus and are not in theexa
amp parameter on the Mustang Floor (or the pedal can be set to off in Expression mode). Some common uses are to control the frequency parameter of a Wah effect or the rate/time parameter of a modulation or delay effect. Pedal Menus Press the PEDAL button to configure the Mustang Floor expression pedal as well as an external EXP-1 expression
1. Amp Off When this switch is in OFF position you are using only the Guitar Models, therefore . 26 Fender Mustang Neck Neck 1 27 Fender Mustang Neck Neck 2 28 Fender Mustang Mid Mid 3 29 Fender Mustang Bridge Bridge 4 30 Fender Mustang Bridge Bridge 5 . In this instruction manual the lightning within a triangle means “Electrical caution!”.
Fender Super Champ X2 Manual. There are so many controls on this amp that there's no way you can't get the sound you want. Fender Super Champ X2 Manual. Fender X2 Features. Two separate . Fender Guitar Amplifier Owner's Manuals (Archive) – Fender Fender Super Champ x2 Review Part I - YouTube Fender Super-Sonic 2-Channel Tube Amp .
Fender Champ (Harvard ’58 model), Fender ’62 Brown Deluxe, Fender ’72 Princeton, Fender Custom Shop Vibroking, Fender Pro Junior, Fender Rumble 30 watt bassamp, Fender Vibroking 2x12”
Use Fender FUSE software to control your Mustang from your computer and access bonus amp features not available from the Mustang alone. Please see the Fender FUSE manual at www.fender. com/support for details. Record and edit Mustang
MUSTANG SKID STEER LOADER . PARTS MANUAL . Prior to serial #5476803 . PART #000-34884 Revised January 1994 Revised September 2008 . mus . Mustang Manufacturing Company, Inc. A GEHL Company . Printed in U.S.A. -----USE ONLY GENUINE MUSTANG REPAIR PARTS . If service and repairs are needed, see your MUSTANG dealer and always insist on GENUINE MUSTANG Parts, in order to receive the highest in .
210-hp Mustang V6 300-hp Mustang GT 500-hp Shelby GT500 . 4 Carpeted front floor mats with chrome badging 4 Mustang rocker stripes and Pony fender badges The Exterior Sport Appearance Package (shown righ
content; Ableton Live Lite 8 Fender Edition studio-quality recording software; and AmpliTube Fender LE software. # # # About Fender Musical Instruments Corporation Fender Musical Instruments Corporation
MAGAZINE 42 FENdER MAGAZINE FENdER.coM 5 08 Intro Green Day’s Mike Dirnt welcomes you to your brand-new window into the world of Fender 14 Visitor Center The ultimate Fender experience – see what’s inside the swanky new visitor facility in Corona, California 20 News Find out what guitars, amplifiers and effects
