MANUAL - HiModel

SUPER-LINK 2.4GHz RADIO ADAPTERMANUALSUPER-LINK 2.4 GHz Module CW-8MANUALNotice：Notice：Please read the manual carefully before using itI

MANUALSUPER-LINK 2.4GHz RADIO ADAPTERCatalogueState . 2Support & service 2Specific symbol 2Flight safety . 2SUPER-LINK CW-8 module and accessories 3SUPER-LINK CW-8 compatible . 4Charging instruction . 5About SUPER-LINK system 5SUPER-LINK CW-8 parameter . 5SLink series receiver parameter . 5SUPER-LINK CW-8 layout instruction . 6Operation . 6SUPER-LINK CW-8 installation . 6Bind . . 6SUPER-LINK CW-8voltage calibrate . . 7SLink series receiver installation . 7Failsafe 8ID setting . 8Attach：Module LED indicate . 8www.super-link.cn-1-

MANUALSUPER-LINK 2.4GHz RADIO ADAPTERStateThanks for choosing SUPER-LINK 2.4GHz module CW-8 and its series receivers. Wesuggest you read the manual carefully before using this itemSupport and serviceIf you have any question on using the unit, please read the manual carefully. You can alsocontact with our dealers or visit www.super-link.com to get the customer service.Specific symbolPlease notice these symbols and read them carefully.Dangerous：：If you can’t operation as normal, it may be dangerous or bad to your life.Warning：：If you can’t operation as normal, it may be dangerous or bad to your life.Notice：：If you can’t operation as normal, it may be dangerous or bad to your life.Symbol：：ProhibitForceFlight safetyAny electronic may lose control, please set up failsafe correctly to avoid or reducelosses. If you find the unit with problem please don’t use it and contact us intime.Don’t use it in the rainy day or windy.For the operator itself operation error caused by damage to the product, or arederived from the other problems, it shall not with SUPER - LINK.Range is affected by the environment .Please test range in the open away fromany obstacles.Our range test is based on ground.Due to some receivers with high sensitivity, some of RX and TX may hasblocking(In general. The distance of RX wire and TX wire keeps within30CM).This won’t influence the normal workingPlease note the positive and negative charges on the voltage protector,don’tmake mistakewww.super-link.cn-2-

SUPER-LINK 2.4GHz RADIO ADAPTERMANUALSUPER-LINK CW-8 module and accessories for chooseCW-8 modulewww.super-link.cn-3-

MANUALSUPER-LINK 2.4GHz RADIO ADAPTERAccessories include：：CW8 module X1CW8 antenna X1S1 . X1S2 . X1SUPER-LINK CW-8 compatible4YF (72MHz), 4YBF, 6EX, 6J, 8J, 7C, 8FG, 9C, 10C &S1(included)12FGFutaba4VF, 5U, 6A, 6DA, 6H, 6YF, 6YG, 7NFK, 8U & 9ZS34YF (2.4GHz), 12Z, 14MZ & 18MZS1(included) &S6JRAll aircraft transmitters with trainer/DSC jackS2(included)S4 & S6WFLYWFT06II, WFT07II, WFT08, WFT08X, WFT08,WFT09, WFT09IIWFT06X-A, FT06-A, FT06-CS5 & S6HitecNeon, Flash 4sx, 5, 5sx, Focus 4, 6, Laser 4, 6, Optic 5(72MHz), Optic 6 (72MHz, 2.4GHz), Eclipse 7S3(72MHz), Prism 7 & Prism 7XAurora 9Optic 5, Optic 6 Sport & Eclipse 7 (2.4GHz)S5 & S6DX6, DX6i & DX7S2(included)DX4e, DX5e, DX7s, DX8, DX10t & DX18S5 & S64TH & 6XMS1(included)4FM & 6FMS3GraupnerMX-16S2 (included)FSFS-CT6B,S4 & S6WalkeraAll aircraft transmitters with trainer/DSC jackS5 & S6SpektrumTower HobbiesCharging instructionIf analog of radio with power, you can use S1or S3 to work with super-link CW8If analog of radio with power, but the charge port with power, you can use S2 to work withSUPER-LINK CW8.If analog and charge port without power, you can use S4or S5 to work with SUPER-LINKCW8, and meantime use S6 to supply power for SUPER-LINK CW8 module.www.super-link.cn-4-

MANUALSUPER-LINK 2.4GHz RADIO ADAPTERAbout SUPER-LINK SYSTEMSUPER-LINK CW-8 module and receivers with the standard of Frequency-Hopping SpreadSpectrum (FHSS), so in actual use, the surrounding environment of the interference signalis difficult to interference signals from the transmitter and receiver. This ensure safe, stable.The system has high reliability, good compatibility, the better control, more agileidentification control and lower power consumption. It adopts DC power; the normalworking current is less than 30 mA, which saves electricity. At the same time, the SUPER LINK CW8 module will supply the firmware to users for updating.SUPER-LINK CW8 module and Slink series receiver features Long Range, light weight Easy to bind and operation Receiver is small and light Failsafe. You can set the receiver to default to a pre-set position on all channels in theunlikely event of signal loss. Scan the clear frequency channel and then make signal transmission. Ultra-low power design.SUPER-LINK CW-8 mAOperatingVoltage3.7 4.2V(connect with 1S battery)4 12.6V(power supplied by Transmitter)Power 100mWResolution1µsSlink receivers specificationsItem ��Dimension(mm)17X15.1X5.624 15.1 5.634.2 18.4 8.7Weight1.1g2.2g9gControl range400m800m800mOperating Voltage3.7V 6.0V3.7V 6.0V4.8V 6.0Vwww.super-link.cn-5-

SUPER-LINK 2.4GHz RADIO ADAPTERMANUALSUPER-LINK CW-8 version instructionSUPER-LINK CW-8 installation1.2.3.4.5.6.7.Inserting the simulated line to the analog port of SUPER-LINK CW8;Screw the 2.4G antenna and ensure antenna tightening;Reference to “Slink receivers bind” to operate the bind of module and receiver;Reference to "SUPER - LINK CW8 voltage calibration" to make the calibration voltage;Reference to “Failsafe setting” to set the failsafe of receiver;Reference to “ ID setting” to change the ID;After finished above, please find the suit place for the module on the transmitter andplease avoid the antenna touched with metal;Kindly inform: SUPER-LINK CW8 had finished calibration voltage, ID setting, if thereis no special need, please don’t do the operate.Slink receivers Bind1. Press the button on the TX module and turn on the transmitter. The LED on the modulewill light red and green for 1s, please remove your hand during the green light 1s.Thebuzzer will sound one , the LED on the module will flash between red and green ,getsinto bind state.www.super-link.cn-6-

MANUALSUPER-LINK 2.4GHz RADIO ADAPTER2、SLink4RC reference to Slink 4rc(Bind way 1)；SLink4R、SLink7Rreference to bind way2.Bind way1 （suit to SLink4RC）Bind way 2（suit to SLink4R、SLink7R）After SUPER-LINK gets into bind,connect the receiver to the battery;The LED on the receiver will light.The LED will flash quickly and goout. This shows that the receiverhas bound to the module. Turn offthe power to the receiver and turnoff the transmitter.After bind of SUPER-LINK CW8,press and holdthe button on the receiver. Connect the receiver tothe battery. The LED on the receiver will light(LED will light 1s, please make sure to releasedyour hand within 1s), The LED will flash quicklyseveral times and go out. Turn off the power to thereceiver. If you do not want to bind more receiversat this time, turn off the transmitter.Don’t press any button on the module. Turn the transmitter on. The module LED should begreen. Connect the receiver to the battery. The red LED on the receiver will flash threetimes (now it is searching for the frequency) and light on for long, indicating the receiver isoperating properly. If not bind successful, the red LED on the receiver will put off or flash.The receiver will not be initialized; it is also the most safe test model boundary.SUPER-LINK CW8 voltage calibratePress the button the module and turn on the transmitter (supply power to module), The LEDon the module will light red and green for 1s, please remove your hand during the greenlight 1s.The buzzer will sound two, gets into voltage calibrate, In the battery outlet connectthe correct 4.2 V standard voltage, press the button until the buzzer gave a short sound,voltage calibration finished.SLink receivers installationwww.super-link.cn-7-

MANUALSUPER-LINK 2.4GHz RADIO ADAPTERFailsafe setting:Any electronic may lose control, please set up failsafe correctly to avoid or reduce losses.1. after initial binding, turn on the transmitter.2. Press and hold the button on the receiver (under the symbol of “Thumb”). Connect thereceiver to the battery. The LED on the receiver will light（about 1s） and then go out(for about 1s）. At this time (when the LED off) remove your hand from the receiverbutton. The LED on the receiver will go on.3. Move the joystick on your transmitter to where you want the surfaces / motor etc to bein the event of lost signal. Press the button on the receiver .The LED will flash severaltimes; this shows the receiver has remembered the position which you have set. In therare event that your system losses signal, all channels will return to the position whichyou have set.4. Turn off the power to the receiver. Failsafe is now set.5. Check that failsafe works, by turning on the transmitter then the receiver / model. Turnoff the transmitter. The controls should go to their preset position. They will return tothose on the transmitter when power is restored.ID SettingPress the button on the module and turn on the transmitter, the red and green LED willlight for 1s,then green and red light for 1s again, please released the button within1s, thebuzzer will sounds three and gets into ID mode. During accounting ID, buzzer will sound ashort, one ID one sound, now press the button and buzzer will sound a long, and it meansID was saved.If you don’t released the button in time or the time press the button is long, the modulewill gets into normal working.Attach: Instruction of LED on the TX moduleGreen LED light onNormal workingYellow LED stay onrange testingLED flash between red and greenBind codeFlash red LEDChange TX module ID conditionIf you have any questions please do not hesitate to contact us or visit our website:www.super-link.cnOr contact with your local supplier.www.super-link.cn-8-

NoticeNotice： ：：：Please read the manual carefully before using itPlease read the manual carefully before using itPlease read the manual carefully before using it . 6J, 8J, 7C, 8FG, 9C, 10C & 12FG S1(included) Futaba 4VF, 5U, 6A, 6DA, 6H, 6YF, 6YG, 7NFK, 8U & 9Z S3 4YF (2.4GHz), 12Z, 14MZ & 18MZ S1(included) & S6 JR All aircraft .