Owner's Manual And Installation Instructions
Owner's Manual andInstallation Instructions Two-SpeedAUTOMATICWASHERSI\\IMPOR'FANT:Read and follow all safetyand operating instructionsbefore first use of this product.Sears,RoebuckPART NO. 3950146and Co., HoffmanRev. BPRINTEDYour washer may look differentfrom the washer shown.Estates,IN U.S.A.IL 60179 U.S.A.
BEFOREUSING YOUR NEW WASHERSEARS RYCARINGWASHERWARRANTYINSTRUCTIONS20YOUR WASHER28TIPS3OFOR YOUR WASHERMAINTENANCE31AGREEMENTPlease read this manual. It will helpyou install and operate your newKenmore washer in the safest andmost economical way.For more information4INSTRUCTIONSTROUBLESHOOTINGSEARS335Use the space below to record the modelnumber and serial number of your newKenmore Washer.about the careand operation of Kenmore appliancescall your nearest Sears store. You willneed the complete model and serialnumbers when requesting information.Your washer's model and serial numbersare located on the Model and SerialNumber Plate.Model No.Serial No.Date of PurchaseII\Model and SerialNumber Plate .Keep this book and your SearsSalescheck(receipt) in a safeplace for future reference.
LIMITED10-YEARWARRANTYFULl. 1-YEAR WARRANTYON MECHANICALANDELECTRICALPARTSON PLASTICFor one year from the date of purchase,when the washer is installed and operatedin accordance with the instructions inthe Owner's Manual, Sears will repair orreplace any mechanical or electrical partsin this washer, if .defective in material orworkmanship.manship. You will be charged for labor.LIMITED 5-YEAR WARRANTYON GEARCASE PARTSAfter one year and until five years fromthe date of purchase, Sears will furnishreplacement part, for any defective gearcase parts. You will be charged for labor.TUBAfter one year and until ten years fromdate of purchase, Sears will furnish areplacement plastic tub for any plastictub which is defective in material or workIf the washer is subjected to other thanprivate family use, the above warrantycoverage is effective for only 90 days.WARRANTY SERVICE IS AVAILABLEBY CONTACTINGTHE NEARESTSEARS SERVICE CENTER IN THEUNITED STATES.This warranty applies only while thisproduct is in use in the United States.This warranty gives you specific legalrights, and you may also have otherrights which vary from state to state.Sears Roebuck and Co., Dept. 817WA,Hoffman Estates, IL 60179.bur safety and the safety of others is very important.We have provided many important safety messages in this manualand on your' appliance. Always read and obey all safety messages.This is the safety alert symbol. This symbol alertsyou to hazards that can kill or hurt you and others.All safety messages will be preceded by the safetyalert symbol and the word "DANGER"or "WARNING"These words mean:You will be killed or seriouslyinjured if you don't followinstructions.You can be killed or seriouslyinjured if you don't followinstructions.All safety messages will identify the hazard, tell you how to reduce theclhance of injury, and tell you what can happen if the instructions arenot followed.
YOURSAFETYIS IMPORTANTTO USWARNING:Toreduce the risk of fire,electric shock, or injury to personswhen using your washer, follow basicprecautions, including the following: Read all instructionsthe washer.before using Do not wash articles that have beenpreviously cleaned in, washed in, soakedin, or spotted with gasoline, dry-cleaningsolvents, other flammable or explosivesubstances as they give off vapors thatcould ignite or explode. Do not add gasoline, dry-cleaningsolvents, or other flammable or explosivesubstances to the wash water. Thesesubstances give off vapors that couldignite or explode. Under certain conditions, hydrogen gasmay be produced in a hot water systemthat has not been used for 2 weeks ormore. HYDROGEN GAS IS EXPLOSIVE.If the; hot water system has not beenused for such a period, before using awashing machine, turn on all hot waterfaucets and let the water flow from eachfor several minutes. This will release anyaccumulated hydrogen gas. As the gas isflammable, do not smoke or use an openflame during this time. Do not allow children to play on or in thewasher. Close supervision of children isnecessary when the washer is used nearchildren. Before the washer is removed fromservice or discarded, remove the lid. Do not reach into the washer if the tubor agitator is moving. Do not install or store this washer whereit will be exposed to the weather. Do not tamper with controls. Do not repair or replace any part of thewasher or attempt any servicing unlessspecifically recommended in the Owner'sManual or in published user-repairinstructions that you understand andhave the skills to carry out.SAVE THESE INSTRUCTIONSIMPORTANT:Observeall governingcodes and ordinances.
INSTALLATIONOVERVIEWFor a complete list of tools and partsneeded, see pages 6-8.A. SELECT LOCATIONFOR YOUR WASHER (pgs. 10-12)Recessed Area/Closet Installation Instructions (p. 10)Laundry Tub Drain System(p. 11)II39"StandpipeDrain System (p. 12)Floor Drain System (p. 12)5
B. RE!MOVESHIPPINGSTRAP(p. 13)Tools Needed:ScissorsC. CONNECTFlashlight (optionaldepending oninstallation)DRAIN HOSE (pgs. 14-15)' TWISTANDPUSHParts Needed:Tools Needed:Pliers that opento 19/le inchesFlashlight (optionaldepending oninstallation)i1 yellow, single-wirehose clamp (top ofdrain hose)1 silver, doublewire hose clamp(bottom of drainhose)
D. CONNECTINLET HOSES TO WASHERTools Needed:(pgs. 15-16)Parts Needed:2 water inlet hosesPliers that opento 1 /18inchesFlashlight (optional dependingon installation)E. CONNECTINLET HOSES TO WATERTools Needed:4 flat water inlet hose washersFAUCETS(p. 16)Parts Needed:Pliers that open to 19/16inchesthosesuc et(optionaldepending oninstallation)Flashlight (optionaldepending oninstallation)7
F. SECUREDRAIN HOSE (p. 17);.,:Tool.,; Needed:Parts Needed:ShippingFlashlight (optionaldepending oninstallation)G. LI-VEL WASHERstrap with fastener(p. 18)hTools Needed:%6-Inch openend wrenchFlashlight (optionaldepending on installation)Parts Needed:Level2 front leveling legs with nutsWood block
Selecting the proper location for yourwasher will improve its performanceand minimizeconcerns like washerwalk or noise.ELECTRICALREQUIREMENTS120-Volt, 60-Hz., AC-only,20-ampere fused electricalrequired. (Time-delay fusebreaker is recommended.)individual branch circuit.15- orsupply isor circuitConnect toWARNING: Improper connection ofthe equipment grounding conductor canresult in.a risk of electric shock. Checkwitha qualified electricianor servicemanGROUNDINGINSTRUCTIONSif you are in doubt as to whether theappliance is properly grounded. Do notmodify the plug provided with the appliance - if it will not fit the outlet, havea proper outlet installed by a qualifiedelectrician.For your personal safety, this washermust be grounded. In the event ofmalfunction or breakdown, groundingwill reduce the risk of electric shockElectricalShock HazardPlug into a groundedoutlet.3-prongDo not remove groundDo not use an adapter.Do not use an extensionprong.cord.Failure to follow these instructionscarl result in death, fire, orelectrical shock.by providing a path of least resistancefor electric current.This washer is equipped with a powersupply cord having a 3-prong groundingplug. To minimize possible shock hazard,you must plug the power supply cordinto a mating 3-prong grounding-typewall receptacle, grounded in accordancewith National Electrical Code, ANSI/NFPA70-latest edition and all local codes andordinances.3-ProngGrounding-TypeWall Receptacle3-ProngGroundingPlugIG rounding.)ProngPower SupplyCord- .
A. SELECTLOCATIONFOR YOUR WASHERRECESSEDAREA/CLOSETINSTALLATIONThis washer may be installed-INSTRUCTIONSin a recessedarea or closet.3"48 sq. in.minimumventilationareaOO,T19"fooooD024 sq. in.minimumventilationarea"1"3'"1 - View(DoorWithVent)*Additionalclearancefor wall, doorandfloormoldingsmay berequired.Toreducetransferof washersounds,a clearanceof 1 inchon the sidesof lhe washeris recommended.**Washer widthcan be 24" or 27"dependingon modelselected. The installation spacing is in inchesand is the minimum allowable. Allow additional space if other appliances are to be installed in the area.10 If closet door is installed, the minimum air openings in top and bottomare required. Louvered doors withequivalent air openings in top andbottom are acceptable.
LAUNDRYTUBDRAINSYSTEMCheck location where washer will beinstalled. This washer can be installedusing one of three, systems: Laundry tub drain system Standpipedrain system Floor drain system(below)(p. 12)(p. 12)Grounded receptacle: Mustbe within 4 feet of where thepower cord is attached to theback of the washer.Support:Floor must be sturdyenough to support a total weightof 315 pounds (including washer,water, and load weight).Do not store or operate washer at orbelow 32 F (some water may remain inwasher). See page 30 for WinterizingInformation.Proper installation is your responsibility.Make sure you have everything necessaryfor correct installation including thefollowing points:Hot and cold water faucets:Must be within 4 feet of thehot and cold water fill valvesattached to the back of thewasher and provide waterpressure between5-100 P.S.I.Water heater: To get thebest washing results, setwater heater to deliver140 F water to washer.Laundry tub drain system:Needs a minimum 20-gallonlaundry tub.Level floor: Maximumallowable slope under entirewasher- 1 inch.Top of tub must be atleast 39 inches highand no higher than96 inches from bottomof washer.11s-
AL']i'ERNATE LOCATIONSSTANDPIPE AND FLOOR DRAIN SYSTEMSSiphon break: Must be purchasedseparately. See chart below.Standpipe drain system: Needsminimum diameter standpipe withcarry-away capa(;ity of 17 gallonsTop of standpipe must be at leasthigh and no higher than 96 inchesbottom of washer.a two-inchminimumper minute.39 inchesfromFloor drain system: Requires a siphonbreak, see chart below. A minimum carryaway capacity of 17 gallons per minute isrequired.If you have:You will need to buy:Laundry tub or standpipehigher than 96 inchesSump pump system(if not already available)1-inch diameter2-inch diameter to 1-inch diameterstandpipe adapter, Part No. 3363920OverheadFloor drainsewerstandpipeStandard 20 gallon, 39-inch high draintub or utility sink and sump pump(available from local plumbing suppliers)Siphon break, Part No. 285320;additional drain hose, Part No. 3357090;and Connector Kit, Part No. 285442Parts listed are available from your local Sears store or Sears ServiceCall 1-800-366-PART (1-800-366-7278).12Center.
B. REMOVESHIPPINGSTRAPRemoving the shipping strap isnecessary for smooth operation.If the shipping strap is notremoved, the washer will makeexcessive noise.STEP 3. Pull firmly to removeend of the shipping strap thatpinned to the back of washer.release the rear self-levelingtheremainsThis willlegs.To prevent floor damage, set washer ontocardboard before moving across floor.Move washer close to its final location.STEP 1. Read, then remove the labelover the electrical plug and shipping strap.STEP 2. Pull the yellow shipping strapcompletely out of the washer. Thereshould be three cotter pins on the endof the shipping strap when it is pulledout of the washer. ]he electrical plug isattached to this shipping strap.PinPULLSTEP 4. Cut the shipping strap about16 inches from plug end. Look for thewords "CUT HERE" Remove shippingstrap from the electricalplug.Electrical plug0ShippingstrapPinNOTE: For use in securing the drainhose, save the end of the shipping strapthat does not have the three cotter pins.Discard the rest.13
C. CONNECTDRAINHOSEmProper connection of the drain hosewill protect your floors from damagedue to water leakage.TWISTANDPUSHSTEP 1. To prevent the drain hose fromcoming off or leaking, it must be installedper the following instructions:IMPORTANT: This procedure must befollowed to ensure proper installation.a. Wet the inside of the straight end ofthe drain hose with tap water. DONOT USE ANY OTHER LUBRICANT.b. Squeeze ears ofclamp with pliersover the straight1/4inch from thesilver, double-wireto open. Place clampend of the drain hoseend.d. Place clamp over area marked"CLAMP." Release clamp.1/4"DrainHose\\c. Open clamp. Twist hose back andforth while pushing down onto drainconnector at the bottom of the washer.Continue until hose contacts theribbed stop on the cabinet.If you have:You will need to buy:Drain hose that is too shortDrain hose, Part No. 388423 andhose kit, Part No. 285442Drain hose that is too longHose kit, Part No. 285442A problem with lint cloggingyour drainDrain protector,Part No. 367031Parts listed are available from your local Sears store or Sears Service Center.Call 1-800-366-PART(1-800-366-7278).14
For standpipesystems:or laundry tub drainSTEP 2. Open yellow, single-wire clampwith pliers and slide over hooked endof drain hose to secure the rubber andcorrugatedsections together.HookedEndD. CONNECT INLET HOSESTO WASHERProper connection of your inlet hoseswill allow hot and cold water to enteryour washer properly. It also helpsprevent water damage due to leaks.Drain HoseSlip and Fall HazardUse new water inlet hoses.STEP 3. Put hooked end of drain hoseinto laundry tub or standpipe. Checkfor proper length of drain hose. Rotatehook to eliminate kinks.To prevent drain water from going backinto the washer: Do not straighten hooked end of drainhose and force excess drain hose intostandpipe. Do not lay excess drain hose in bottomof laundry tub.1Failure to do so can result in headinjury or broken bones.NOTE: Replace inlet hoses after fiveyears of use to reduce the risk of hosefailure. Periodically inspect and replaceinlet hoses if bulges, kinks, cuts, wear,or leaks are found. When replacingyour inlet hoses, mark the date ofreplacement on the label with apermanent marker.STEP 1. Insert one new, flat washer(from the parts bag) into each end ofthe inlet hoses. Check that washersare firmly seated in couplings.0COUPLINGWASHER15
STI-P 2. Attach the hose with the redcoupling to the hot water (bottom) inletvalve. Attaching the red coupling firstmakes it easier to tighten connectionwith pliers. Screw on coupling by hand.Make an additional two-thirds turn withpliers to tighten coupling. DO NOTOVI--RTIGHTEN; this could damagethe valves.ColdWaterInlet ValveE. CONNECTTO WATERINLET HOSESFAUCETSSTEP 1. Make sure washer basket isempty. Run water through both faucetsinto a bucket or laundry tub to get rid ofparticles in the water lines that mightclog hoses. Determine which faucet ishot and which is cold. Mark the hot waterfaucet.HotWaterInletValveSTEP 3. Attach the hose with the bluecoupling to the cold water (top) inletvalve. Screw on coupling by hand. Makean additional two-thirds turn with pliersto tighten coupling. DO NOT OVERTIGHTEN; this could damage valves.STEP 2. Attach the hose with the redcoupling to the hot water faucet. Screwon coupling by hand. Make an additionaltwo-thirds turn with pliers to tighten coupling. DO NOT OVERTIGHTEN;thiscould damage the coupling.STEP 3. Attach the hose with the bluecoupling to the cold water faucet.Screw on coupling to faucet by hand.Make an additional two-thirds turn withpliers to tighten coupling. DO NOTOVERTIGHTEN;this could damagethe coupling.STEP 4. Turn on water faucets andcheck for leaks. A small amount ofwater may enter the washer. You willdrain this later.If you have:You will need to buy:Water faucets beyond thereach of water fill hoses2 longer water fill hoses: 6 ft. hoses,Part No. 76314 or 10 ft. hoses,Part No. 350008Parts listed are available from your local Sears store or Sears ServiceCall I-800-366-PART(1-800-366-7278).16YCenter.
SECUREDRAINHOSESecuring the drain hose properly willprotect your floors from damage dueto water leakage.STEP 1. Move washer to its finallocation.-4If the water faucets and drain standpipeare recessed, put hooked end of drainhose in standpipe. Tightly wrap theshipping strap around the drain hoseand water inlet hoses (not the handlesor stems). Push fastener into thenearest hole in the shipping strapI1iJSTEP 2. Use the shipping strap you cutand removed (without the three cotterpins) and tightly wrap it around the drainhose and laundry tub or standpipe. Pushfastener into the nearest hole in theshipping strap.iiFastener17I.
G. LEVEL WASHERLeveling your washer properly prevents excessive noise and vibration.To install front legs:STI-P 1. Prop front of4 iP,ches). Use a woodobject that will supportwasher. If washer waswall, move the washertipping it up.STI-Pscrewof leginitialwasher up (aboutblock or anotherthe weight of theplaced against aout slightly before2. With one of the legs in hand,lock nut onto leg % inch from topbase. This is the recommendedsetting.STEP 5. Move washer to its finallocation.STEP 6. Tilt washer forward until rearof washer is at least 3 inches off floor.You may hear the self-adjusting rearlegs click into place. Lower washer tofloor. Check levelness of the washerby placing a level on top of the washer,first side-to-side; then front-to-back.3/8"rhiSTEP 3. Screw' leg into washer base byhand until nut reaches washer base.Repeat for other leg.vISTEP 7. If washer is not level, propup the front of the washer and adjustthe legs up or down as necessary. Lowerwasher and reset self-adjustingrear legs(as in Step 6). Repeat Step 7 until thewasher is level.STEP 8. When washer is in its finallocation and level, use a 9/18-inch openend wrench to turn nuts on front legstightly against washer cabinet. If nuts arenot tight against washer cabinet, thewasher may vibrate.STEP 4. Tilt washer backward untilfront of washer is off the wood block.Remove wood block. Gently lowerwasher to floor.18
:iEVIEW INSTALLATIONTake a few minutes to completethis checklist. It will help assure youthat you have a proper installationand increase your satisfaction withyour Kenmore washer.[] Check electrical requirements.Be sure you have correct electricalsupply and recommended groundingmethod.[] Check that: The washer is level. The nuts on the front legs are tight.[][] Check that you have:Check that the water faucets areturned on. All the tools you started with. Removedall packaging Removed shippingthree cotter pins.materials.strap with Installed all parts listed onpages 6-8.FINAL STEPS[] Plug power supply cord intogrounded outlet.[]Remove the blue protective film onthe console and any tape remainingon washer.[] Take a few minutes and read theOperating Instructions (pages 20-27)to fully understand your new washer.Then, start the washer and allow itto complete the NORMAL Cycle.19
STARTING WASHERTo get the maximum cleaning andfabric care from your washer, pleaseread and follow these instructions.NOTE: The drawings in this sectionshow the basic features of all modelscovered by this manual. Refer to thesu#plied "Feature Sheet" for yourwasher's particular features.STEP 1. Add measured detergentdirectly into washer basket Then placea load of sorted clothes in the washer.STEP 2. (OPTIONAL STEP) If desired,add measured liquid chlorine bleach tothe liquid bleach dispenser (if available);(see page 25).STEP 3. (OPTIONAL STEP) If desired,add measured liquid fabric softener tothe fabric softener dispenser (if available'j(see page 26).STEP 4. Close washerlid.STEP 5. Set WATER LEVEL Control Obased on the size of your wash load.STEP 6. Set the WATER TEMPERATUREControl.ExplosionHazardSTEP 7. Set RINSE OPTIONSNever place items in the washerthat are dampened with gasolineor other flammable fluids.No washer can completelyremove oil.Do not dry anything that has everhad any type of oil on it (includingcooking oils).Failure to follow these instructionscan result in death, explosion,or fire.(if available);Control(see page 23).STEP 8. Push the Cycle Selector Control(Timer) Knoband turn to the right. Setcycle and time according to the type offabric in the load (see page 22).STEP 9. Pull the Cycle Selector Con
out of the washer. ]he electrical plug is attached to this shipping strap. STEP 3. Pull firmly to remove the end of the shipping strap that remains pinned to the back of washer. This will release the rear self-leveling legs. Pin PULL Electrical plug 0 STEP 4. Cut the shipping strap about 16 inches from plug end. Look for the words "CUT HERE .
er's Manual and the following Owner's Man‐ uals: Integrated Owner's Manual in the vehicle. Online Owner's Manual. MINI Motorer’s Guide App. Notes on updates can be found in the appendix of the printed Owner's Manual for the vehicle. Owner's Manual for Navigation, Entertainment, Communication Owner's Manual for Navigation, Entertainment,
Owner's Manual and the Integrated Owner's Manual in the vehicle. Notes on updates can be found in the ap-pendix of the printed Owner's Manual for the vehicle. Owner's Manual for Navigation, Entertainment, Communication The Owner's Manual for Navigation, Enter-tainment, and Communication can be ob-tained as printed book from the service cen-ter.
p/n: IM-1JD4120 INSTALLATION & OWNER’S MANUAL The contents of this envelope are the property of the owner. Be sure to leave with the owner when installation is complete. CAB INSTALLATION INSTRUCTIONS JOHN DEERE 4000 SERIES (4500/4600/4700)
Independent Personal Pronouns Personal Pronouns in Hebrew Person, Gender, Number Singular Person, Gender, Number Plural 3ms (he, it) א ִוה 3mp (they) Sֵה ,הַָּ֫ ֵה 3fs (she, it) א O ה 3fp (they) Uֵה , הַָּ֫ ֵה 2ms (you) הָּ תַא2mp (you all) Sֶּ תַא 2fs (you) ְ תַא 2fp (you
Owner's Manual & Installation Manual IMPORTANT NOTE: Read this manual carefully before installing or operating your new air conditioning unit. Make sure to save this manual for future reference. Please check the applicable models, technical data, F-GAS(if any) and manufacturer information from the "Owner's Manual - Product Fiche "
DuoDiner DLX 6-in-1 Highchair Chaise haute 6 en 1 DuoDiner DLX Silla alta 6 en 1 DuoDiner DLX Owner'Owner's Manual Manual du propriétaire s Manual Manual del propietario
5.3. STAFInst Uninstall 6. Platform Installation Notes 6.1. Linux installation 6.2. AIX installation 6.3. HP-UX IA64 64-bit installation 6.4. IBM i 32-bit (previously known as i5/OS or OS/400) installation 6.5. z/OS installation 6.6. FreeBSD installation 6.7. Mac OS X installation 6.8. Solaris installation 7. Environment Variable Settings 7.1.
193 M/s. Murugappa Morgan Thermal Ceramics Ltd., Brand Owner 194 M/s. Abbott India Ltd., Brand Owner 195 M/s. RPG Life Sciences Ltd., Brand Owner 196 M/s. Endurance Technologies Ltd., Brand Owner 197 M/s. Modi Distillery, Brand Owner 198 M/s. Kohinoor Speciality Foods India Pvt. Ltd., Brand Owner 199 M/s. Keventer Agro Ltd., Brand Owner 200 M/s.
