TS-590S - Radiomanual.info
TS-590SADJUSTMENTUpdating the FirmwareThe firmware of the main MCU and DSP can be updatedusing the “TS-590 Update” update software. Update thefirmware according to the procedure displayed in updatesoftware.Refer to the help file of the update software for a detailed procedure.Download the latest “TS-590 Update” update softwarefrom the following /software download.html* The URL may change without notice.11. Audio Analyzer12. RF Dummy Load1) Impedance: 150 and 502) Dissipation: 150W or greater13. Linear Detector1) Frequency range: 60MHz or greater14. Power Meter1) Impedance: 502) Dissipation: 300W continuous or greater3) Frequency limits: 60MHz or greater15. Spectrum Analyzer1) Frequency range: 100kHz to 140MHz or greater2) Bandwidth: 1kHz to 3MHzNote: Update the firmware after replacing the main MCU orFlash memory.16. Tracking Generator17. Directional Coupler18. Monitor Receiver19. MicrophoneRequired Test Equipment20. Distortion Meter21. Double Signal Pad (50 )MC-43S or MC-60S81. DC Voltmeter (DC V.M)1) Input resistance: More than 1M2) Voltage range: 1.5 to 1000V AC/DCNote: A high-recision multimeter may be used. However,accurate readings can not be obtained for high- impedancecircuits.2. DC Ammeter1) Current range: 100mA, 1.5A, 30A, high-precision ammeter may be used.3. RF VTVM (RF V.M)1) Input impedance: 1M and less than 3pF, min.2) Voltage range: 10mV to 300V3) Frequency range: 10kHz to 500MHz4. AF Voltmeter (AF V.M)PreparationUnless otherwise specified, knobs and switches shouldbe set as follows.POWER .ONNOTCH . CenterAF . MINRF . MAXSQL . MIN Front panel1) Frequency range: 50Hz to 10kHz2) Input resistance: 1M or greater3) Voltage range: 10mV to 30V5. AF Generator (AG)1) Frequency range: 200Hz to 5kHz2) Output: 1mV or less to 1V, low distortion6. AF Dummy Load (DM. SP)1) Impedance: 82) Dissipation: 3W or greater7. OscilloscopeRequires high sensitivity, and external synchronizationcapability (150MHz or greater). Rear panel8. Standard Signal Generator (SSG)1) Frequency range: 50kHz to 60MHz2) Output: –133dBm/0.1µV to 7dBm/1V3) Output impedance: 504) AM and FM modulation can be possibleNote: Generator must be frequency stable.9. Frequency Counter (f. counter)1) Minimum input voltage: 50mV2) Frequency range: 150MHz or greater10. Noise Generator (Noise G.)Must generate ignition noise containing harmonics beyond 60MHz.67
TS-590SADJUSTMENTService Jig ACC 2 connector short plugUse the same adjustment jig as the TS-570.Menu No. How to use the ACC 2 connector short plugInsert the adjustment jig into the ACC 2 connector located on the rear panel of the transceiver.2. Select the adjustment mode Menu No.Turn the [MULTI/CH] knob to change the Menu No.3. Change the adjustment mode setting dataSetting data can be changed using the [ ] or [ ] key.4. Write the adjustment mode dataPress the [ ] or [ ] key on the main unit or the [UP] or[DWN] key on the microphone on Menu No. 60.5. Cancel the adjustment modePress the [CLR] key to return to normal VFO mode.Note: When the power is turned OFF during the adjustmentmode, adjustment mode is canceled. Adjustment Mode Menu (Menu No. 00 62)No.AdjustmentItem000110M 2.7kCAR Point02 Outline1. You can adjust the transceiver in service adjustmentmode (adjustment using the panel keys) or with manualadjustment (turning a coil and trimmer, etc). The serviceadjustment mode (hereinafter referred to as “adjustment mode”) has 63 items (Menu No. 00 to 62) and alladjustment data is stored in the EEPROM (X53-446 A/3:IC309).2. You can enter adjustment mode and change each settingdata.3. New data is written to the EEPROM by performingMenu No. 60 writing.1. How to start the adjustment mode Insert the adjustment jig into the ACC 2 connector located on the rear panel of the transceiver. Turn the transceiver ON while pressing the [MIC] keyand [NR] key, to enter adjustment mode and the MenuNo. appears on the Memory channel number display.Remove the adjustment jig from the transceiver whenthe Menu No. appears.681.81Mode73USB11M 2.7k1.8111USB11M 500H1.8111CWHF 11M IF GainHF11 GAIN14.211USB04HF 73M IF GainHF73 GAIN14.273USB0511M Mix BALHF11 BAL0.13611USB0673M Mix BALHF73 BAL0.10073USB07AGC ReferenceAGC 73USB50.273FM50.273FM73USB73CW09HF.SSB S1HF S-Meter10111213141517HF FM S-MeterHF FM Squelch50M IF Gain21222350M S-Meter26HF.FM.SFULHF.FM.SQ.THHF.FM.SQ.TI50. GAIN50.SSB S950.SSB SF50M FM S-Meter50M FM SquelchALC Reference2425HF.FM. S150.SSB S11819HF.SSB S9HF.SSB SF1620 Operation procedures in adjustment modeFrequency RX IF(MHz) (MHz)0308Adjustment ModeConditionDisplayPOC/Power Meter50.FM S150.FMSFUL50.FM.SQ.TH50.FM.SQ.TIALC REF14.1POC 100W14.1P.MTR 100W14.150M 100W50.1
TS-590SADJUSTMENTNo.AdjustmentItem2750P.M100W28POC 50W29P.MTR 50W3031P.MTR 25WPOC 10W33P.MTR 10W34POC 5W35P.MTR 5W3738Frequency RX IF(MHz) (MHz)50.1TX GainALC MeterTGC TGC 1.8M1.8341TGC 3.5M3.5142TGC 5M5.3043TGC 7M7.01TGC 10M10.145TGC 18M18.146TGC 21M21.147TGC 24M24.948TGC 28M29.149TGC 50M50.150PGC 50W5152PGC535455PGC 25WPGC 10W14.1FM PROSWR PRO14.159][]Panel CWPGC 5W5658]Main MCUChecksumdisplay[TGC LWTGCThe checksum of the main MCU, the panel MCU, andthe DSP can be confirmed using the [ ] key or [ ] key. The checksum value of the main MCU appears on the 7segment display while [M-CHKSUM] appears on the 13segment display. The checksum value of the panel MCU appears on the 7segment display while [P-CHKSUM] appears on the 13segment display. The checksum value of the DSP appears on the 7 segment display while [D-CHKSUM] appears on the 13 segment display.[3944ModePOC 25WPOC/Power Meter3236 MENU No.61 is a checksum confirmation modeConditionDisplaySWRHF SWR14.150M SWR50.1117373FMUSBUSB73USBUSB60WRITEWRITE ROM---61CHECKSUMM-CHKSUM---62Display check----69
TS-590S 67 Updating the Firmware The Þ rmware of the main MCU and DSP can be updated using the ÒTS-590 UpdateÓ update software. Update the firmware according to the procedure displayed in update software. Refer to the help file of the update software for a de-tailed procedure. Download the latest ÒTS-590 UpdateÓ update software
How To Connect the Kenwood TS-590S to the SDR-IQ Receiver by Ian Wade, G3NRW g3nrw-radio@ntlworld.com Version 1.0 2 September 2011 Introduction These brief notes explain how to connect the Kenwood TS-590S transceiver to an RFSPACE SDR-IQ software defined radio receiver. This lets y
Kenwood TS-590S. The Kenwood TS-590S is the exciter to my Tokyo Hy-power 1.5. Every once in a while my THP will "kick out" during a QSO with the Overdrive light coming on during transmit. So basically I
Mar 02, 2018 · The TS-590S employs DSP from the IF stage onward. Kenwood was the fi rst to offer DSP-based IF AGC in an Amateur radio (TS-870) and this DSP technology has been further enhanced for the TS-590S, resulting in the development of a unique approa
The TS-590S employs DSP from the IF stage onward. Kenwood was the fi rst to offer DSP-based IF AGC in an Amateur radio (TS-870) and this DSP technology has been further enhanced for the TS-590S, resulting in the development of a unique approa
When Restaurant Manager exports its batch sales transactions, the resulting data is in a "horizontal" structure, similar to the following: Ticket Info Employee Info Sale Info Sale Info Sale Info Sale Info Tender Info Member Info Tip Info For Club Office to be able to use the data, it must be converted into the vertical structure that
My first purchase was an Icom 718 Transceiver and AH-3 antenna tuner. This tuner allowed me to . I read all I could about a new Kenwood rig released in the spring of 2010 the TS-590s. The TS-590s . A type T-130 is a little larger than 1 inch and will dissipate 300 watts of power. This seemed like
Kenwood TS-590S HF and 6 Meter Transceiver It is easy to set up and start making QSOs. Only three connections are required: power . May 2011), ) and . 5
Invitation to Tender TfL/90711 – Bridge Design Consultancy Services Page 9 Closing date for return of ITT responses. 25 February 2013 at 12 noon ITT Evaluation 5 working days Notification of ITT results w/c 11 March 2013 Contract Award w/c 11 March 2013 Please note that TfL reserves the right to change the above dates and timings 13. DURATION OF CONTRACT The Contract will be awarded for 6 .
