SIMATIC HMI 3 - Siemens

Comfort Panels Preface1OverviewSIMATIC HMIHMI devicesComfort Panels2Safety instructionsMounting and connecting the3HMI device4Commissioning the device5Commissioning a projectOperating Instructions6Operating a project7Maintenance and care8Technical specificationsATechnical SupportBAbbreviations03/2012A5E03404994-02

Legal informationLegal informationWarning notice systemThis manual contains notices you have to observe in order to ensure your personal safety, as well as to preventdamage to property. The notices referring to your personal safety are highlighted in the manual by a safety alertsymbol, notices referring only to property damage have no safety alert symbol. These notices shown below aregraded according to the degree of danger.DANGERindicates that death or severe personal injury will result if proper precautions are not taken.WARNINGindicates that death or severe personal injury may result if proper precautions are not taken.CAUTIONwith a safety alert symbol, indicates that minor personal injury can result if proper precautions are not taken.CAUTIONwithout a safety alert symbol, indicates that property damage can result if proper precautions are not taken.NOTICEindicates that an unintended result or situation can occur if the relevant information is not taken into account.If more than one degree of danger is present, the warning notice representing the highest degree of danger willbe used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating toproperty damage.Qualified PersonnelThe product/system described in this documentation may be operated only by personnel qualified for the specifictask in accordance with the relevant documentation, in particular its warning notices and safety instructions.Qualified personnel are those who, based on their training and experience, are capable of identifying risks andavoiding potential hazards when working with these products/systems.Proper use of Siemens productsNote the following:WARNINGSiemens products may only be used for the applications described in the catalog and in the relevant technicaldocumentation. If products and components from other manufacturers are used, these must be recommendedor approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation andmaintenance are required to ensure that the products operate safely and without any problems. The permissibleambient conditions must be complied with. The information in the relevant documentation must be observed.TrademarksAll names identified by are registered trademarks of Siemens AG. The remaining trademarks in this publicationmay be trademarks whose use by third parties for their own purposes could violate the rights of the owner.Disclaimer of LiabilityWe have reviewed the contents of this publication to ensure consistency with the hardware and softwaredescribed. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, theinformation in this publication is reviewed regularly and any necessary corrections are included in subsequenteditions.Siemens AGIndustry SectorPostfach 48 4890026 NÜRNBERGGERMANYA5E03404994-02 04/2012 Technical data subject to changeCopyright Siemens AG 2012.All rights reserved

PrefacePurpose of the operating instructionsThese operating instructions contain information based on the requirements defined by DINEN 62079 for mechanical engineering documentation. This information relates to the place ofuse, transport, storage, mounting, use and maintenance.These operating instructions are intended for: Users Commissioning engineers Maintenance personnelRead especially the information in the chapter "Safety instructions" (Page 25).You can find more information such as operating instructions, examples and referenceinformation in the online help of WinCC.Basic knowledge requiredGeneral knowledge of automation technology and process communication is needed tounderstand the operating instructions. Knowledge of personal computers and the Microsoftoperating systems is required to understand this manual.Scope of the operating instructionsThe operating instructions apply to the following HMI devices in conjunction with theWinCC software package: KP400 Comfort (4" Key Panel) KTP400 Comfort (4" Key&Touch Panel) KP700 Comfort (7" Key Panel) TP700 Comfort (7" Touch Panel) KP900 Comfort (9" Key Panel) TP900 Comfort (9" Touch Panel) KP1200 Comfort (12" Key Panel) TP1200 Comfort (12" Touch Panel) KP1500 Comfort (15'' key panel) TP1500 Comfort (15'' touch panel) TP1900 Comfort (19'' touch panel) TP2200 Comfort (22'' touch panel)Comfort PanelsOperating Instructions, 03/2012, A5E03404994-023

PrefaceCAUTIONManual belongs to HMI deviceThe supplied manual belongs to the HMI device and is also required to repeatcommissioning. Keep all supplied and supplementary documentation for the entireservice life of the HMI device.Provide all stored documents to subsequent owners of the HMI device.TrademarksThe following designations marked with the symbol are registered trademarks ofSiemens AG: HMI SIMATIC WinCC Style conventionsStyle ConventionScope"Add screen" Terminology that appears in the user interface, for example,dialog names, tabs, buttons, menu commands Required input, for example, limits, tag values. Path information"File Edit"Operational sequences, for example, menu commands, shortcutmenu commands. F1 , Alt P Keyboard operationPlease observe notes labeled as follows:NoteA note contains important information about the product described in the manual and its use,or a specific section of the manual to which you should pay particular attention.Comfort Panels4Operating Instructions, 03/2012, A5E03404994-02

PrefaceNaming conventionsTermApplies toPlant System Machining center One or more machinesComfort HMI device KP400 Comfort KP1500 ComfortHMI device KTP400 Comfort TP1500 Comfort KP700 Comfort TP1900 Comfort TP700 Comfort TP2200 Comfort KP900 Comfort TP900 Comfort KP1200 Comfort TP1200 ComfortKey model KP400 Comfort KP1500 ComfortKey HMI device KP700 Comfort KP900 Comfort KP1200 ComfortTouch model KTP400 Comfort TP1500 ComfortTouch HMI device TP700 Comfort TP1900 Comfort TP900 Comfort TP2200 Comfort TP1200 ComfortDeviceWinCCWinCC V11 (TIA Portal) orWinCC V11 SP2 HSP Comfort (TIA Portal)higher for configuring theor higher for configuring15" and largerdevices up to and including the devices12" deviceFiguresThis manual contains illustrations of the described devices. The illustrations can deviate fromthe particularities of the delivered device.Comfort PanelsOperating Instructions, 03/2012, A5E03404994-025

PrefaceComfort Panels6Operating Instructions, 03/2012, A5E03404994-02

Table of contentsPreface . 3123Overview. 131.1Product description .131.2Product package .151.31.3.11.3.21.3.3Configuration of the devices .16KP400 Comfort and KTP400 Comfort .16KP700 Comfort to KP1500 Comfort, TP700 Comfort to TP2200 Comfort .18Ports.191.4Accessories.211.5The HMI device in the operating process .221.6Software options .23Safety instructions . 252.1General safety instructions .252.2Security information .262.3Notes about usage.27Mounting and connecting the HMI device . 293.13.1.13.1.23.1.33.1.43.1.53.1.6Preparation for mounting .29Checking the package contents.29Checking the operating conditions.30Selecting a mounting position .30Checking clearances.32Preparing the mounting cutout.33Labeling the function keys .343.2Mounting the .83.3.93.3.10Connecting the device .41Notes on connection .41Connecting the equipotential bonding circuit .42Connecting the power supply.44Connecting the configuration PC .46Connecting the PLC.48Connecting a USB device .49Connecting a printer.50Connecting an audio device.51Switching on and testing the HMI device.52Securing the cables .53Comfort PanelsOperating Instructions, 03/2012, A5E03404994-027

Table of contents4Commissioning the device . 554.14.1.14.1.24.1.3Overview . 55Backup design. 55Changing memory cards . 58Front operator controls. 604.24.2.14.2.24.2.3Using the service concept . 62Enabling the service concept . 62Replacing HMI device . 63Disabling the service concept . 644.34.3.14.3.24.3.34.3.44.3.54.3.6Operating the device . 65Loader . 65Control Panel . 67Installed programs. 68Reference for system keys. 69Entering values with system keys . 73Using the screen keyboard . ring the device . 79Reference for functions . 79Changing settings for operation . 80Configuring the screen keyboard . 80Setting the character repeat. 82Setting the double-click . 83Calibrating the touch screen . 83Changing password protection . 86Changing HMI device settings . 87Setting the date and time . 87Changing regional settings. 89Backup registry information. 90Changing monitor settings . 91Setting the screen saver . 94Changing the printer properties . 96Enabling sound and setting sound volume . 97Assigning sound to an event . 98Restarting the HMI device. 99Displaying information about the HMI device. 101Displaying system properties . 102Displaying memory distribution . 103Setting storage location. 104Setting the delay time. 105Setting the uninterruptible power supply. 106State of uninterruptible power supply. 108Enabling PROFINET services. 109Synchronizing the time via the time server . 111Changing transfer settings . 113Configuring the data channel . 113Changing MPI/PROFIBUS DP settings . 115Comfort Panels8Operating Instructions, 03/2012, A5E03404994-02

Table of 4.4.144.4.154.4.165Configuring network operation .117Overview of network operation .117Setting the device name of the HMI device .118Changing the network configuration .119Changing the logon data.123Changing e-mail settings .124Configuring Telnet for remote control .125Changing Internet settings .126Changing general Internet settings.126Setting the proxy server .127Changing privacy settings.128Importing and deleting certificates .130Saving to external storage device (backup).131Restoring from external storage device .133Activate memory management .135Commissioning a project . 1375.1Overview .1375.2Operating modes .1385.3Using existing projects .1385.4Data transmission options.1395.55.5.15.5.25.5.3Transfer.140Setting transfer mode.140Start transfer .142Testing a project .1435.65.6.15.6.2Backup and restore.144Overview .144Backing up and restoring data of the HMI device .1455.75.7.15.7.2Updating the operating system .146Updating the operating system .146Updating the operating system of the HMI device .1475.85.8.15.8.25.8.3Managing add-ons and license keys .149Managing add-ons .149Transferring license keys .150Managing license keys.150Comfort PanelsOperating Instructions, 03/2012, A5E03404994-029

Table of contents678Operating a project . 1536.1Overview . 1536.2Function keys . 1566.3Direct keys. 1566.4Setting the project language . 1576.5Input of values. 1586.6Entering and editing numeric values. 1596.7Entering or changing alphanumeric values. 1606.8Displaying infotext . 1626.9Closing the project . 163Maintenance and care . 1657.1Maintaining and caring for the touch screen and keyboard overlay . 1657.2Clean screen for Touch HMI devices. 1667.3Spare parts and repairs. 1677.4Recycling and disposal . 167Technical specifications . 1698.1Certificates and approvals. 1698.28.2.18.2.2Directives and declarations . 172Electromagnetic compatibility . 172ESD guideline . 98.3.108.3.118.3.128.3.13Dimension drawings. 177Dimension drawings of the FKP400 Comfort. 177Dimension drawings of the KP700 Comfort . 178Dimension drawings of the KP900 Comfort . 179Dimension drawings of the KP1200 Comfort . 180KP1500 Comfort dimension drawings. 181Dimension drawings of the KTP400 Comfort. 182Dimension drawings of the TP700 Comfort . 183Dimension drawings of the TP900 Comfort . 184Dimension drawings of the TP1200 Comfort . 185Dimension drawings of TP1500 Comfort . 186Dimension drawings of TP1900 Comfort . 187Dimension drawings of TP2200 Comfort . 188Dimensions for labeling strips . 189Comfort Panels10Operating Instructions, 03/2012, A5E03404994-02