LUBICANTS AND SEALANTS - Ideal Vac
LUBRICANTS AND SEALANTSSOLUTIONS YOU CAN TRUSTOils, Fluids, Sealants and GreasesMechanical Pump OilsMechanical Pump Oil Selection ChartVapour Pump FluidsEdwards Silicone FluidsVapour Pump Fluid Selection ChartGreases and WaxesShop online at shop.edwardsvacuum.com490491493495496498499Contact our customer service teamLubricantsand Sealants489.
Oils, Fluids, Sealants and GreasesWe strongly advise that you use only the recommended grades and qualities of fluids and sealants, tomaintain the high performance of Edwards products. If you use inferior materials, this can lead to a reduction inthe pump or system efficiency, partial or complete failure of the equipment, and excessive outgassing. We think it is a falseeconomy to use cheaper fluids and sealants which are untried for many demanding applications. All our fluids and sealantsare tested under formal laboratory conditions. In addition, we have gained considerable on-site experience through ourown use of these materials and by maintaining close contact with users who have specific problems. As many cases ofsuspected equipment under-performance are eventually traced to the use of unsuitable or unsatisfactory fluids andsealants, we are pleased to advise on the correct selection of fluids and sealants for your application.Mineral-based materialsThese materials include rotary pump oils, Diffstak anddiffusion pump oils and greases. They are available withor without various additives for different applications.Silicone-based materialsThese materials are used for Diffstak and diffusionpump fluids and greases. They compriseeither Tetramethyltetraphenyltrisiloxane c compoundsThese include various hindered esters, phenyl ethersand napthalene based compounds. They are offeredfor use in Diffstak and diffusion pumps, but they canalso be used as a rotary pump oils in certain uniqueapplications. Edwards can advise on the matching ofthe fluids to particular applications.Fluorinated materials (PFPE)These are perfluoropolyethers. Perfluoropolyether isa fully fluorinated material free from other halogensand from hydrogen, and so is of particular value wherefreedom from hydrocarbons is important. It is inert tomost reactive chemicals such as UF6, F2, O2, O3, andso on, and it does not polymerise when exposed toelectron and most ion bombardment.Perfluoropolyether fluid is available in grades suitablefor use in rotary pumps. A low vapour pressureFomblin grease (AR555) is available which combinesgood lubrication properties with superiorvacuum properties.PFPE for semiconductor applicationsThe major growth in the use of perfluoropolyether(PFPE) compounds has been in applications wherehostile process conditions quickly destroy normalhydrocarbon pump oils. This applies particularly insemiconductor processing. The corrosion resistantproperties and chemical inertness of PFPE resultLubricants490. and Sealantsin greatly increased operation times between oilchanges and pump maintenance, and this providesa cost effective solution to many difficultpumping applications.These are the basic properties of PFPE and theadvantages for use in vacuum systems: Chemically Inert Ideal for pumping aggressivematerials, particularly in semiconductor processes. High Oxidation Resistance Fluid is not damaged byrepeated exposure to air at operating temperatures. Non-Inflammable No fire risk. High Thermal Resistance No residual tar compoundsformed by overheating. Eventually reduced togaseous products. Oxygen Compatible Allows absolutely safe pumpingof oxygen (NASA approved for liquid oxygensystems). Maximum recommended operationtemperature and pressure for 100% oxygen is 250 Cand 91.4 kg cm-2 and 60 C, 175.75 kg cm-2. Non-polymerisation Does not polymerise onexposure to energetic particle bombardment(except hydrogen ions). This reduces the impact ofbackstreamed vapours, and is an important propertywhere polymers cannot be tolerated (for example,in electron microscopes). Miscible with most common solvents. Allows pumping of solvent even without gas ballast.Before charging with PFPE, thoroughly clean the pumpsto achieve maximum advantage. If you do not haveskilled technicians available, we recommend that youreturn the pumps to a Edwards Service Center to becleaned and filled. Some models of high vacuum rotarypumps and mechanical booster pumps adapted for usewith PFPE are available as standard and can be found inthe appropriate sections of this catalogue: these pumpsare assembled and tested with PFPE.Safety note Perfluoropolyether is a fluorinatedcompound and will give-off toxic vapours if exposedto temperatures above 280 C. Do not expose PFPE tonaked flames and prohibit smoking in work areas.
Mechanical Pump OilsMechanical pump oils Edwards supplies the widest range of oils of different viscosities and specifications to enablecustomers to obtain the best performance from mechanical pumps under different application conditions.Mineral oils are manufactured by a hydro treatment process to reduce carcinogenic risk. All are specially preparedfor high vacuum use, having low vapour pressures even at high temperatures. The particular mechanical pumpspecification should be consulted to find which oil to use.Ultragrade mineral oilsEdwards offers a range of mineral oils, Ultragrade 15, 19, 20 and 70, which result from a new process. Mostmanufacturers use a solvent refining process, whereas these oils are produced by a unique hydrotreating process.This process eliminates nitrogen, sulphur and oxygen and the aromatic hydrocarbons, leaving a clear base stockessentially free of impurities. When combined with additives, the Ultragrade oils give improved vacuum performance,thermal and oxidation stability and rust inhibition. The anti-oxidants included in the oils enable the pump to withstandhigh operating temperatures without oil degradation, so extending intervals between oil changes.The properties of the oils allow them to be used in a wide range of applications. New Ultragrade 70 oils are thebest choice for large pumps used in heavy-duty, cycling applications. Contact Edwards or your local supplier fordetailed recommendations.Ultragrade oilUse inReplacesUltragrade 15E2M0.7, E2M1.5. Also suitable for cold start applicationsEdwards 8AUltragrade 19RV pumps, E2M18, E2M28Supergrade A, Edwards17 and 20Ultragrade 70E2M40 to E2M275–Ultragrade 20EH boostersEdwards 16 and 18Ordering informationProduct descriptionUltragrade 15Ultragrade 19Ultragrade 20Ultragrade 70Order no:1 litreH1102601512 1 litreH110260124 litreH110260134 4 litreH11026011205 litreH110260101 litreH1102501512 1 litreH110250124 litreH110250134 4 litreH11025011205 litreH110250101 litreH1102401512 1 litreH110240124 litreH110240134 4 litreH11024011205 litreH110240104 litreH110280134 4 litreH11028011205 litreH11028010Shop online at shop.edwardsvacuum.comContact our customer service teamLubricantsand Sealants491.
Edwards TW has been developed for applications where rotary pump oilsare likely to be exposed to reactive or corrosive gases. The oil is distilledhydrocarbon containing no additives, but unsaturates and aromatic linkshave been removed. The result is that the oil will last up to 20 times longer,depending on process, than refined mineral oils. Longer oil life significantlyextends the intervals between oil changes.Product descriptionEdwards TW mineral oilOrder no:EuropeN. America1 litreH11012015H02100001TW4 litreH11012013H02100002TW20 litreH11012026H02100003TW205 litre(55 US gal)N/AH02100004TWEdwards 45 oilEdwards 45 is a hydrocarbon synthetic polymer whose molecularstructure offers chemical inertness, high temperature stability and lowvapour pressure ( 10-7 mbar at 25 C). It is commonly used in massspectrometry applications because of its well defined peaks. Edwards45 oil is non-toxic, non-corrosive and reclaimable.Product descriptionOrder no:EuropeN. AmericaEdwards 45 oil1 litreH11022015H018000014 litreH11022013H01800003N/AH0180000512x 1 litreV-LubeThe V-Lube range of oils offer good thermal stability and oxidationresistance and have been selected for use with the Stokes range ofvacuum pumps. Choose from the following:V Lube OilApplicationV Lube B-V Lube FMicrovac piston pumpsV Lube GHot Microvac, 912H, 612MBV Lube HMB boostersProduct descriptionV-Lube B oilV-Lube G oilV-Lube H oilV-Lube F oilLubricants492. and SealantsOrder no:3.8 litres (1 US gal) North America only254-117-00119 litres (5 US gal) North America only254-539-001208 litres (55 US gal) North America only297-854-00119 litres (5 US gal) North America only262-461-003208 litres (55 US gal) North America only421-793-0013.8 litres (1 US gal) North America only424-051-00119 litres (5 US gal) North America only419-699-001208 litres (55 US gal) North America only419-698-0015 litres (1.3 US gal)H1103000125 litres (6.6 US gal)H11030002205 litres (54 US gal)H110300033.8 litres (1 US gal) North America only254-117-00219 litres (5 US gal) North America only254-539-002208 litres (55 US gal) North America only421-780-001
Fomblin 25/6Krytox 1525 Krytox 1514 Fomblin 16/6Ultragrade 70 Krytox 1506Ultragrade 20 Fomblin 06/6Ultragrade 19Mass spectrometersEdwards TWUltragrade 15Mechanical Pump Oil selection chartApplicationElectron microscopes Thin film sputtering Surface studies UHV systems Leak detection TV tubes Power valves Distillation Space studies Furnaces EB welders SemiconductorsImpregnation Chemical pumping Oxygen pumpingRadioactivePackaging Mechanical booster Metallisation Technical data1.3 10-76 10-53.9 10-54 10-81.3 10-42.6 10-71 10-33 10-65.2 10-71.3 10-34 10-65 10-31.3 ific gravity at 15 C0.860.860.860.860.8601.881.881.891.891.91.9at 20 C104.2143.73522221556470168140276250at 40 C3 10-3–2.1 10-72.1 10-73.0 10-31 10-81.0 10-3Molecular weight100 C3.0 10-220 C5.8 10-6Vapour pressure mbarViscosity cSt38.148.61037065252248488080Pour point C-18-16-12-12-12-50-45-45-40-35-35Flash point C220220220230243none*none*none*none*none*none*Auto ignition point 0000000Sulphur content % mass/massPropertiesEnergetic particle impactNo polymers formed (except with H2 ions)Conducting polymers formedThermal stabilitygoodgoodgoodgoodpoorExcellent – decomposes to gas only above 300 C1Oxidation resistancegoodgoodgoodgoodpoor tofairExcellentChemical resistancefairfairfairfairpoor togoodExcellentRadiation resistancefairfairfairfairfairGood – but reacts with electro-positive metals(for example, sodium)* WARNING – Perfluoropolyether is a fluorinated compound which will give off toxic vapours if exposed to temperatures above 280 C. The fluid should not beexposed to naked flames and smoking should be prohibited in the working area. Suitable for this application.Lubricants† Vapour pressure at 25 C.Shop online at shop.edwardsvacuum.comContact our customer service teamand Sealants493.
Perfluoropolyether oilsProduct descriptionOrder no:Fomblin YVAC 06/6Krytox 1506 fluidFomblin YVAC 16/6Krytox 1514 fluidFomblin YVAC 25/6Krytox 1525 fluidFomblin Drynert YVAC25/6 fluid1 kg (532 ml)H113010195 kgH113010208 kgH026004006*1 kg (532 ml)H113070185 kg (2660 ml)H113070201 kg (529 ml)H113060195 kgH113060208 kgH026001006*1 kg (529 ml)H113080185 kg (2646 ml)H113080201 kg (529 ml)H113120195 kg (2646 ml)H113120208 kgH026008006*50 kgH026008007*1 kg (526 ml)H113090185 kgH113090201 kg (529 ml)H113120215 kg (2646 ml)H11312025Edwards offers a range of Fomblin and Krytox ,perfluoropolyether oils for use in rotary vacuumpumps. Fomblin YVAC 06/6 and Krytox 1506 arerecommended for Edwards oil sealed rotary pumps andare practically a direct replacement for mineral oil interms of viscosity and vapour pressure. Krytox 1525is suitable for use in rotary pumps requiring a viscosityequivalent to Fomblin YVAC 25 fluid. Fomblin YVAC16/6 and Krytox 1514 are recommended for use inperfluoropolyether adapted mechanical booster pumps.Similar viscosity grades of Fomblin and Krytox areinterchangeable and miscible. Edwards, in conjunctionwith Ausimont UK, has developed Drynert fluid whichcontains anti-rust and antiwear additives soluble inFomblin . These additives cover metallic surfaces with aprotective, corrosion resistant film.* N. America only.Single stage and rough pump oil selection chartVapour pressure mbarLOWVAC 60V-Lube FV-Lube GV-lube H20 C7.5 10 -5 1.3 1.3 1.3100 C3.9 10 1.3 1.3 1.3Molecular weight485350-500350-500350-500Specific gravity at 20 C0.800.86-0.880.88-0.890.88-0.91Viscosity cSt at 40 C 059.195.5-100183-191208-220-2Pour point C-45-36-30-25Flash point C209223216220360TBC343343Auto ignition point CSulphur content % mass/mass0 0 0.281 0 0PropertiesEnergetic particle impactConducting polymers formedThermal stabilitygoodgoodgoodgoodOxidation resistancegoodgoodgoodgoodChemical resistancefairfairfairfairRadiation resistancefairfairfairfairLubricants494. and Sealants
Vapour Pump FluidsEdwards supplies a range of fluids of different vapour pressures andphysical properties. From this range, you can choose the optimumfluid for your applications. In general, the more volatile fluids are usedwith vapour booster pumps and for vapour diffusion pumps used onindustrial processes (for example, decorative coating and vacuumfurnaces) where high gas loads are encountered and high critical backingpressure is advantageous. The less volatile fluids are used for processesor experiments requiring more exacting high vacuum conditions. Theleast volatile fluids are used for clean or ultra high vacuum applications(mass spectrometry, electron probe apparatus, surface studies, and soforth). Fluid selection depends also on the particular physical and chemicalcharacteristics of the fluids (apart from vapour pressure).Edwards has a long history of co-operation with various fluidmanufacturers in the development of new pumping fluids and is wellplaced to advise in cases of uncertainty.AP201 Vapour booster pump fluidApiezon AP201 is a hydrocarbon fluid prepared by molecular distillationand protected against oxidation by a thermally stable additive of matchedvapour pressure. It has an auto ignition temperature of 305 C. It exhibitsa fair degree of resistance to chemical degradation (so that highthroughputs of air and water vapour can be pumped without damage tothe fluid) and it can withstand limited accidental admission of atmosphericair at operating temperature. The fluid has low viscosity which permitseasy filling and draining. It does not attack synthetic rubbers used forseals and gaskets in vacuum systems. It is non-irritant, non-toxic andenvironmentally non-polluting.Product descriptionOrder no:AP201 vapour booster pump fluid4 litresH0260105420 litresH02601052200 litresH02601050Edwards L9 diffusion pump fluidEdwards L9 fluid has been developed for use in Diffstak and diffusionpumps. It is a naphthalene based synthetic material which is ideal for usein applications where silicones (which form insulating films) cannot betolerated. L9 fluid is rugged, has a very good vacuum performance andgives an ultimate pressure of typically 5 10-9 mbar (at 20 C). In addition,the fluid is chemically stable and is resistant to acids, alkalis, halogens andoxides of nitrogen. It does not react with common engineering metals orelastomers. It is immiscible to the common solvents alcohol, acetone andtrichlorotrifluoroethane. The toxicity level of L9 is very low.Safety note: When changing to this fluid the pump should be cleanedusing a proprietary fluid. The pump should then be rinsed in acetone anddried prior to re-charging.Product descriptionOrder no:Edwards L9 fluid 1 litreH11501015Shop online at shop.edwardsvacuum.comContact our customer service teamLubricantsand Sealants495.
Edwards SiliconeThese synthetic fluids are organo-silicon oxide polymers and have exceptional chemical stability both at hightemperature and when in contact with most gases and vapours. They provide a range of general purpose fluids forultimate vacuum from about 10-5 to 10-9 mbar, and are particularly useful in industrial processing applications dueto their exceptional ruggedness. High throughputs of air, water vapour and corrosive gases can be pumped withoutfluid degradation. The fluids can withstand repeated admission of atmospheric air while at operating temperatureand are widely used in valveless quick-cycle pumping processes. They have low toxicity and good resistance togamma radiation.Fluid breakdown products (due to bombardment and so on) tend to be electrically insulating and so we do notrecommend these fluids for physical electronic applications such as mass spectrometers and surface analysissystems. The fluids are indifferent lubricants. Their decomposition is catalysed by traces of alkali metals (forexample, caesium) and their use should be avoided where possible.Silicone 704Silicone 705Description:Silicone 704 is a Tetramethyltetraphenyltrisiloxanebased fluid for producing high vacuums in the range10-7 to 10-8 mbar. This fluids exhibits extreme chemical,thermal, oxidation, hydrolysis and radiation resistance.It also has extremely low back-streaming properties.Description:Silicone 705 is a Pentaphenyltrimethyltrisiloxane basedfluid for producing ultra high vacuums in the range 10-9to 10-11 mbar due to extremely low vapour pressureand back-streaming rates It exhibits extreme chemical,thermal, oxidation, hydrolysis and radiation resistance.Applications:Silicone 704 is intended for use in particularly tough,rugged applications including vapour depositionof thin films by sputtering or evaporation, electronbeam operations and high vacuum furnaces, melting,degassing and sintering, refractory metals and thickfilm deposition.Applications:Silicone 705 is intended for use where ultrahigh andultraclean vacuum conditions are required. The UHVcharacteristics particularly useful for thin film, surfacetechnology, thermonuclear and plasma physicsapplications as well as electron microscopes.It is also suitable for all aspects of vacuum coatingsuch as optics and automotive components and theUHV characteristics are particularly useful for thinfilm, surface technology, thermonuclear and plasmaphysics applications.Technical dataTypical ultimate vacuum achievable at 20 C (mbar)Vapour pressure @ 25 C (mbar)Boiling temperature at 1.3 mbar ( C) (approx)Viscosity cSt @ 25 CExtreme stability and high spontaneous ignitiontemperature make it ideal for use in space-simulationchambers. Low vapour pressure and low backstreamingrate make cold and refrigeration traps unnecessaryfor pressures in the 10-8 mbar range. However with aliquid nitrogen trap ultimate pressures of 10-11 mbar canbe achieved.Technical data8.0 x 10-91 x 10-921537 - 42Typical ultimate vacuum achievable at 20 C (mbar)Vapour pressure @ 25 C (Pa)Boiling temperature at 1.3 mbar ( C) (approx)Viscosity cSt @ 25 CPour point C-34Flash point C 210Pour point C1.06 - 1.07Flash point CSpecific gravity at 25 CSpecific gravity at 25 CProduct description8.0 x 10-112 x 10-11245165 - 185-14 2431.09 – 1.10Order no:H02400060Product descriptionSilicone 704 oil 1 kg SSH02400061Silicone 705 oil 500 ml SSH02400070Silicone 704 oil 5 kg SSH02400062Silicone 705 oil 1 kg SSH02400071Silicone 704 oil 500 ml SSLubricants496. and SealantsOrder no:
Santovac 5 diffusion pump fluidThis synthetic fluid is a polyphenyl ether developedfrom fluids originally produced as lubricants for spacevehicles. It has exceptionally low vapour pressure,exceptional thermal stability and a tendency to wetsurfaces less readily and ‘creep’ to a lesser extent thanis common with most fluids. The fluid is employedfor the cleanest high vacuum and ultra high vacuumapplications down to less than 10-9 mbar (for example,electron microscopes, mass spectrometers and surfacephysics studies) where its excellent high vacuumperformance and low tendency to migrate into thepump system particularly recommend it. The fluid ischemically stable, non-corrosive, safe and non-toxicat normal operating temperatures. Fluid breakdownproducts (due to bombardment and so forth) tendto be electrically conducting. Lubricating qualitiesare good and the fluid finds application to lubricatemechanisms in vacuum systems.Product descriptionSantovac 5 fluidOrder no:EuropeN. America100 mlH11401001H02300045500 mlH11401002H02300046Shop online at shop.edwardsvacuum.comContact our customer service teamLubricantsand Sealants497.
Vapour Pump Fluid Selection ChartApiezon AP201Santovac 5L9Mass spectrometers Electron microscopes Thin film sputtering Surface studies UHV Systems Leak detection TV tubesPower valves Spaces studies Furnaces RadioactiveVapour booster MetallisationTypical ultimate6.5 10-51.3 10-95 10-95 10-62.6 10-107.8 10-10at 100 C2.4 10-26.5 10-62.6 10-5at 150 C6.5 104 102.3 10-316029525131044640720 C34240071.3100 C5.0125.6Vacuum achievable at 20 C (mbar)Vapour pressure(mbar) at 20 C-1-4Boiling temperatureat 1.3 mbar ( C) (average)Molecular weight (average)Viscosity cSt at150 C2.74.51.2-30 5-5Flash point ( C)196288241Fire point ( C) (approximate)204350281Auto ignition point ( C) (approximate)305590370Specific heat (cal/g/ C)0.46–0.46Pour point ( C) (approximate)Latent heat (cal/g)Specific gravity at 25 CCoefficient of expansion per ( C)Refractive index at room 042(10-30 C)(25-50 C)(25-50 C)1.4761.63061.5154(25 C)(25 C)Energetic particle bombardmentThermal stabilityconducting polymers formedpoorexcellentgoodOxidation resistancepoor to fairvery goodgoodChemical resistancepoorgood verygoodRadiation resistancefairvery goodfairLubricants498. and Sealants
Greases and WaxesSilicone greaseWaxes and sealing compounds (mineral based)A high vacuum grade grease, which is for use at systempressures lower than 10-6 mbar. Apiezon wax W is a low vapour pressure wax forsealing joints in high vacuum systems. This waxsoftens at 80-90 C and has a vapour pressureat 80 C of 10 -3 mbar and at 20 C of 10 -8 mbar.Apiezon wax W40 is similar to type W, but has alower softening point which makes it very suitablefor flow sealing in or around vacuum joints. It is notrecommended for use at temperatures above 30 C. It has a vapour pressure at 20 C of 10 -7 mbar.Apiezon sealing compound Q remains firm fortemperatures up to 30 C, but is sufficiently pliable topermit easy moulding into position. It is an excellentmaterial for shielding or blanking off sections ofapparatus. The compound is easily applied and canbe readily removed. It has a vapour pressure at 20 Cof 10 -4 mbar.Ordering informationProduct descriptionOrder no:Silicone, high vacuum grease, tube 50 gH02400036Silicone, high vacuum grease, pack 5 kgH11251015PFPE grease This grease is an excellent lubricant for slidingelastomer seals, and exhibits the chemical inertnesstypical of the PFPE range. It has a very low vapour pressure and is suitable foruse in the presence of gaseous and liquid oxygenunder severe conditions. The general purpose AR555 grease offered byEdwards has the basic properties of Fomblin PFPE,but the vapour pressure is not specifically controlled.The vapour pressure is 10-7 mbar at 20 C.Ordering informationProduct descriptionOrder no:AR 555 PFPE Vacuum Grease 100 gH11350013Ordering informationProduct descriptionApiezon W waxOrder no:20 x 25 gH02301014Apiezon W wax pack1 kgH11176007Apiezon W40 wax pack250 gH02301015Apiezon Q sealing compound tin1 kgH02300012Krytox greaseDuPont Krytox fluorinated greases are a family ofmultipurpose lubricants intended for use in specialityapplications at elevated temperatures or in aggressiveenvironments.Ordering informationProduct descriptionOrder no:N. AmericaKrytox 240AD, tube (57 g, 2 oz)U30002525Krytox 240AD, tube (226 g, 8 oz)U30002206Krytox 240AB, tube (57 g, 2 oz)U30002536Krytox 240AB, tube (226 g, 8 oz)U30002535Krytox 240AC, tube (57 g, 2 oz)U30002538Krytox 240AC, tube (226 g, 8 oz)U30002537Krytox LVP, tube (57 g, 2 oz)U30002075Krytox LVP, tube (226 g, 8 oz)U30002539Shop online at shop.edwardsvacuum.comContact our customer service teamLubricantsand Sealants499.
Apiezon greasesA range of Apiezon greases is offered for useon high vacuum systems and for many generalapplications in the laboratory. These high puritygreases are non-toxic, easy to apply, easy to cleanoff and have long shelf lives.Applications include: Lubrication of glass and metal taps invacuum systems Sealing polymer joints in vacuum systems Leak detection Protecting metal contacts invacuum-encapsulated relays Sealing polished and ground glass/metal surfaces Optical surfaces in vacuum systems and lasersystems – does not cause clouding (L and Mgreases only) Non vacuum uses include lubrication of glassand metal taps in laboratory, medical andindustrial applications Good ‘gettering’ qualities (absorbs greaseand chemical impurities) – ideal forelectronics industryChoice of grease depends largely on operatingtemperature (see below).Anti-sieze greasesAP100AP101Melting point47 C 200 CNoNoRadiation resistantVapour pressure at 20 C (mbar)Comments 10 10-5-10High vacuum; good lubrication, resistsalkali, acid and corrosive gas; easilyremoved by most solvents. Particularlygood for polished/ground glass joints.Medium vacuum, heavy duty grease;wide temperature base, ideal forlaboratory work.Lubricant (unmodified)Melting pointRadiation resistantLubricant (polymers added)Melting pointRadiation resistantVapour pressure at 20 C (mbar)CommentsM44 CYesYes 10-10 10 High vacuum, low temperature; nuclear,space industries; liquid gas chromatographySimilar to L grease, but stiffer;good gettering propertiesVapour pressure at 20 C (mbar)CommentsL47 CNTH43 C125 CN/A*NoNoNo 10 10 10-7Rubbery, tenacious;cushions glass matingsurfaces, ideal for burettetaps. Cryogenic.As N grease, but highertemperature; glass andgeneral lubrication.Very high temperature;becomes stiffer astemperature increases.-9-8*Grease H can withstand temperatures up to 250 C without meltingProduct descriptionApiezon L grease (50 g)Apiezon L grease (25 g)Order no:EuropeN. 01040Apiezon M grease (25 g)N/AH11151002Apiezon N grease (25 g)H02301011H02301011Apiezon T grease (25 g)H02301018H02301018Apiezon AP100 grease (50 g)H02300043H02300043Apiezon AP101 grease (50 g)H02301044H02301044Apiezon AP101 grease (4 kg)H02301045H02301045Apiezon H grease (25 g)H11150001H11150001Apiezon M grease (100 g)Lubricants500. and Sealants
Shop online at shop.edwardsvacuum.com Contact our customer service team 49. Lubricants and Sealants SOLUTIONS YOU CAN TRUST LUBICANTS AND SEALANTS Oils Fluids Sealants and Greases 490 Mechanical Pump Oils 491 . (5 US gal) North America only 254-539-001 208 litres (55 US gal) North Amer
Zero differential pressure type pilot operated 2 port diaphragm type 2.0 MPa (Resin body type 1.5 MPa) Aluminium, Resin, C37 (Brass), Stainless steel Note 1) NBR, FKM, EPDM Dust-tight, Water-jet-proof type (equivalent to IP65) Note 2) Location without corrosive or explosive gases 24 VAC, 48 VAC, 100 VAC, 110 VAC, 200 VAC, 220 VAC, 230 VAC, 240 VAC
IDEAL 4810-95 IDEAL 4850-95/EP IDEAL 5221-95EP IDEAL 6550-95EP B C A 4 x Only IDEAL 4810-95, IDEAL 4850-95/EP, IDEAL 6550-95EP Remove the stand from the wooden pallet. Only IDEAL 4810-95, IDEAL 4850-95/EP, IDEAL 6550-95EP 4 strong people are required to lift the machine from the pallet and place it on the stand. Secure with 4 .
IDEAL 4810-95 IDEAL 4850-95/EP IDEAL 5221-95EP IDEAL 6550-95EP B C A 4 x Only IDEAL 4810-95, IDEAL 4850-95/EP, IDEAL 6550-95EP Remove the stand from the wooden pallet. Only IDEAL 4810-95, IDEAL 4850-95/EP, IDEAL 6550-95EP 4 strong people are required to lift the machine from the pallet and place it on the stand. Secure with 4 .
1/16” dia . (1 .6 mm) Maximum Temperature Limits (diaphragm / ball / seat . A- Solenoid 120 VAC,110 VAC and 60 VDC B- Solenoid 12 VDC, 24 VAC and 22 VAC C- Solenoid 240 VAC, 220 VAC and 120 VDC . y PX01X-HDS-XXX are Groundable Acetal pumps: Use the pump ground lug provided. Connect to a
3. Check trailer brake lights and turn signals. 4. Check UTILITY VAC fuel level. 5. Make certain battery is charged and ready to start UTILITY VAC engine. 6. Make certain suction hose and suction tubes are stored on board UTILITY VAC UTILITY VAC SET UP PROCEDURE: 1. Position UTILITY VAC n
* May be used with Mini Clik II, Toro Rainswitch model 850-74, or other normally closed Rainswitch devices. Models 2510 2520 2514 Power In 110 VAC 220 VAC 110 VAC Power Out 110 VAC 220 VAC 24 VAC Relay Contactor rated up to 2 H.P. Relay Contactor rated up to 2 H.P. Built in Transformer K-Rain - Hydrotek Controllers Instructions Page 9 of 9
0.5 A @ 230 Vac - Inrush Current max, 35 A @ 115 Vac 65 A @ 230 Vac 35 A @ 115 Vac 60 A @ 230 Vac Efficiency 79% typ. 88% typ. 80% typ. Leakage Current 1 mA @ 240 Vac Power Factor Correction Meets EN61000-3-2 Class A Output Nominal Voltage 5 V24 V - Tolerance /-2% Voltage Adjustable Range
The themes of pilgrimage and welcome are central to The Canterbury Journey. A lasting part of its legacy will be the new free-to-enter Welcome Centre with dedicated community and exhibition spaces and viewing gallery. The journey to our new centre is underway, to open in 2019. A New Welcome In 2017, the face of the Cathedral has changed .
