Chipkin Automation Systems

ES PanelProgrammer’s Manual574-849Rev. U

Copyrights and TrademarksCopyright 2003-2011 SimplexGrinnell LP. All rights reserved.Specifications and other information shown were current as of publication and are subject to change withoutnotice. No part of this document may be reproduced or transmitted in any form or by any means, electronic ormechanical, for any purpose, without the express written consent of Tyco Safety Products.Simplex, the Simplex logo, MAPNET II, IDNet, TrueAlarm, SmartSync, InfoAlarm, WALKTEST, MINIPLEX, andTrueAlert are trademarks of Tyco International Ltd. and its affiliates and are used under license. VESDA is atrademark of Vision Products Pty Ltd.Simplex fire alarm technology is protected by the following U.S. Patent Numbers:TrueAlarm analog smoke detection: 5,155,468; 5,173,683 and 5,543,777. IDNet andMAPNET II addressable communications; 4,796,025. TrueAlert addressable notification;6,313,744 and 6,426,697. SmartSync horn/strobe control; 6,281,789.ii

Cautions and WarningsCautionsandWarningsREAD AND SAVE THESE INSTRUCTIONS- Follow the instructions in this installation manual. These instructions must befollowed to avoid damage to this product and associated equipment. Product operation and reliability depend upon properinstallation.DO NOT INSTALL ANY SIMPLEX PRODUCT THAT APPEARS DAMAGED- Upon unpacking your Simplex product,inspect the contents of the carton for shipping damage. If damage is apparent, immediately file a claim with the carrier and notifyan authorized Simplex product supplier.ELECTRICAL HAZARD - Disconnect electrical field power when making any internal adjustments or repairs. All repairs shouldbe performed by a representative or authorized agent of your local Simplex product supplier.STATIC HAZARD - Static electricity can damage components. Handle as follows: Ground yourself before opening or installing components. Prior to installation, keep components wrapped in anti-static material at all times.EYE SAFETY HAZARD - Under certain fiber optic application conditions, the optical output of this device may exceed eyesafety limits. Do not use magnification (such as a microscope or other focusing equipment) when viewing the output of this device.FCC RULES AND REGULATIONS – PART 15 - This equipment has been tested and found to comply with the limits for a Class A digitaldevice pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when theequipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installedand used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.SYSTEM REACCEPTANCE TEST AFTER SOFTWARE CHANGES - To ensure proper system operation, this product must be tested in accordancewith NFPA 72 after any programming operation or change in site-specific software. Reacceptance testing is required after any change, addition ordeletion of system components, or after any modification, repair or adjustment to system hardware or wiring.All components, circuits, system operations, or software functions known to be affected by a change must be 100% tested. In addition, to ensurethat other operations are not inadvertently affected, at least 10% of initiating devices that are not directly affected by the change, up to a maximum of50 devices, must also be tested and proper system operation verified.IMPORTANT: Verify FACP System Programmer, Executive, and Slave Software compatibility wheninstalling, or replacing system components. Refer to the Technical Support Information andDownloads website for compatibility information.iii

iv

Table of ContentsCopyrights and Trademarks .Cautions and Warnings.How to Use this Publication .Introduction.General Conventions.Keyboard Conventions .Using the Mouse .iiiiixxxxxxxxxxiChapter 1Installing the PC Programmer . 1-1Introduction.1-1In this Chapter .1-1System Requirements . 1-2System Requirements .1-2Other Required Components.1-2Attaching the Software Key . 1-3Overview.1-3Installation .1-3Installing the Programmer . 1-4Introduction.1-4Installation Procedure.1-4Chapter 2Overview . 2-1Introduction.2-1In this Chapter .2-1Notice to Users, Installers, Authorities Having Jurisdiction, and Other Involved Parties.2-1Programming Overview . 2-2Typical Programming Process.2-2Interface Overview. 2-3Introduction.2-3Tabs.2-4Icons .2-5Chapter 3Basic Operations . 3-1Introduction.3-1In this Chapter .3-1Starting the Programmer . 3-2Procedure .3-2Creating a New Job . 3-3Starting a New Job .3-3Importing an OASYS Transfer File .3-5Opening an Existing Job. 3-6Guidelines.3-6Procedure .3-6Entering the Panel CPU Number . 3-7Entering the Panel CPU Serial Number .3-7Building a Job . 3-8Overview.3-8Procedure .3-8Saving a Job. 3-10Save Option.3-10v

Table of ContentsUsing the Save As Option .3-11Archiving, Backing Up, and Restoring Jobs. 3-12Introduction.3-12Archiving a Job .3-12Backing Up a Job .3-13Restoring a Backed Up or Archived Job.3-13Converting a 4100 Job to an ES Panel Job . 3-15Guidelines.3-15Converting a Job .3-15Reviewing and Verifying the Job .3-16Entering Notes/Setting Preferences . 3-18Entering Notes.3-18Setting Preferences .3-18Chapter 4Panel Information, System Options, and Restricting Access to DisplayFunctions. 4-1Introduction.4-1In this Chapter .4-1Entering General Information . 4-2Open General Information Screen.4-2Enabling and Disabling System Options. 4-3Introduction.4-3Detailed System Option Descriptions .4-4Restricting Access to Operator Interface Functions. 4-12Introduction.4-12Step 1. Edit Access Levels .4-12Step 2. Edit Passcodes .4-13Chapter 5Specifying Hardware Components . 5-1Introduction.5-1In this Chapter .5-1Overview. 5-2Introduction.5-2Hardware Tab Window .5-2Adding and Editing Units. 5-4Introduction.5-4Adding a Unit .5-4Editing Unit Properties.5-4Adding and Editing Boxes and Bays . 5-5Introduction.5-5Adding a Box .5-5Editing/Viewing Box and Bay Properties .5-5Adding Cards . 5-7Introduction.5-7Adding Option Cards .5-7Annunciator Numbers.5-8Annunciator Number Sharing Rules .5-8Annunciator Number Sharing Examples .5-9Card Manipulation Considerations .5-9Editing Basic Card Properties.5-10vi

Table of ContentsChapter 6Editing Non-Audio Card Properties . 6-1Introduction.6-1In this Chapter .6-1Editing RUI-Specific Property Settings . 6-2Accessing the RUI-Specific Settings .6-2Editing Settings.6-2Editing Service Port-Specific Settings . 6-3Accessing the Service Port.6-3Setting Communication Settings .

iii Cautions and Warnings Cautions and Warnings READ AND SAVE THESE INSTRUCTIONS- Follow the instructions in this installation manual. These instructions must be followed to avoid