Front & Rear Sway Bar Kit Installation Instructions
Audi S4 (‘04 )#22829Audi A4 (’02 )#22823Audi RS4 (’06 )#22832Front & Rear Sway Bar Kit Installation InstructionsTools Required:Included In Kit:1) 4-Post lift or floor ramps2) 13mm socket3) 16mm socket4) 16mm wrench5) 18mm wrench6) medium extension(not required, but handy)1)2)3)4)front and rear sway bars4 bushings & 4 brackets2 front bushing mounting platesgrease packsSTART WITH THE REAR BAR .1/Drive the vehicle onto a 4-post lift or floor ramps. THE CAR NEEDS TO BE ATYou cannot have the suspensionhanging while installing this bar!NORMAL RIDE HEIGHT FOR PROPER INSTALLATION.2/Once vehicle is raised, take a moment and observe the stock rear bar andthe way in which it is mounted.3/Release both sides of the exhaust from the two rubber hangers at the rearand let hang. (ok to use small amount of WD40 to loosen) or release themounting bolts with a 13mm socket.
4/Remove the two lower end link bolts (16mm wrench) which attach thesway bar ends to the end links. You may need to hold the wrench-flat with a17mm wrench.5/Remove the four bushing bracket bolts (13mm wrench) attaching the antiroll bar brackets to the sub-frame and save them.6/As you begin to remove the bar, gently free each end from the end linksleeves. Now that the bar is free, slightly lower the exhaust by applying pressureto the tips just enough to remove the bar towards the front or the rear of the car.
7/Repeat same pressure to the exhaust and position H-Sport bar (withoutthe bushings and brackets) in the stock location with the “H-Sport” sticker facingrearward, right side up.8/Apply supplied grease to inner-channeled portion of both rear bushings.(approx. half of one tube for rear bushings) Then install the bushings to the barat approx. the stock location. Position the bar in the stock location then installthe brackets over the bushings with the grease fittings pointing down.9/Re-install the four stock bracket bolts, include the four suppliedwashers, to the new brackets and leave loose while you insert the small end linksleeve to each end of the bar. Re-install the end link bolts and leave loose.Tighten the four bracket bolts, then tighten the end links bolts. Six bolts, all tight.
*Adjustability Note: choose the inner hole (2nd from bar end) for a moreaggressive feel and the outer for solid front-to-rear balance. Loosen thelower end link bolts(2 under cast arm each side) on the bottom side of thelower arm in order to adjust to desired hole.10/Finally, re-attach exhaust hangers to the metal tabs on both sides.YOU’RE DONE WITH THE REAR, NOW THE FRONT!!1/Drive the vehicle onto a 4-post lift or floor ramps. THE CAR NEEDS TO BE ATNORMAL RIDE HEIGHT FOR PROPER INSTALLATION. You cannot have the suspensionhanging while installing this bar!2/Once vehicle is raised, use a standard screwdriver and remove the aeropan fasteners. Then remove the pan entirely exposing the anti-roll bar.3/Take a moment and observe the stock front bar and the way inwhich it is mounted.4/Remove the lower end link bolts (16mm wrench) to the bar and save.Then, remove the four bracket nuts (13mm socket) and save. Remove the stockbar.5/Apply second tube of grease to each inner-channeled portion of the twonew front bushings and attach to H-Sport bar against the outside of the washers.Slip the new brackets over the bushings.
6/Lift the bar up to the vehicle with the two smaller H-Sport stickers at theends right-side-up. As you lift the bar up to the mounting points, you mustplace one mounting plate per side between the bushing and the mountingpoint. This relocates the bushing out of the stock bushing pocket. Re-install thebracket nuts and tighten. Re-install the end link bolts and tighten well usingmedium strength thread locker.**Note** If vehicle is raised using jack stands or other, the bar end and theend link may not align properly. Lower vehicle so that front suspension isnot at full droop and ends will align. Be sure to thread end link bolt byhand at first to prevent cross-threading.8/Re-install the aero pan.Enjoy your new tubular sway bar kit from H-Sport! If you need assistance withthe install or have any other questions, go to the ‘instructions’ button on our siteor call us at the number below.Thank you for choosing the best anti-roll bar kit available for your S4 and A4!H-SportMark Hotchkis562.907.7757 ext 227www.h-sport.com12035 Burke St. Suite 13Santa Fe Springs, CA 90670
Enjoy your new tubular sway bar kit from H-Sport! If you need assistance with the install or have any other questions, go to the ‘instructions’ button on our site or call us at the number below. Thank you for choosing the best anti-roll bar kit available for your S4 and A4! H-Sport Mark Hotch
H-Sport HIGHLY recommends that this sway bar set be installed by a professional, as the front sway bar can only be removed or installed by detaching the front subframe cradle and lowering it from the vehicle! INSTALLATION OF H-SPORT FRONT SWAY BAR » Drive the vehicle on a 4-
2 Valve body KIT M100201 KIT M100204 KIT M100211 KIT M100211 KIT M100218 KIT M300222 7 Intermediate cover (double diaphragm) - - - KIT M110098 KIT M110100 KIT M110101 4 Top cover KIT M110082 KIT M110086 KIT M110092 KIT M110082 KIT M110082 KIT M110082 5 Diaphragm KIT DB 16/G KIT DB 18/G KIT DB 112/G - - - 5 Viton Diaphragm KIT DB 16V/S KIT
rear front base pairs rear front 1-pc multi-slot bases ext multi-slot bases rear front rear front anschutz . rear front base pairs rear front 1-pc multi-slot bases ext multi-slot bases rear front rear front} topper 30, 22 jet & mod 158 (pre 1973) 18 60a (48064)} handy rifle 82 (48082) herters} j9 45 (48045) 46 (48046) 402 (48108) s45 (48226 .
Remove OE Front Bar. a) Disconnect the sway bar end links from the sway bar ends. b) Undo the bushing brackets by unfastening the 2 nuts for each bracket c) Bar should be loose from the vehicle. Note the OE orientation for reference. Installation of Hotchkis Front Sw
1 22810252 Front Sway Bar, 2003 Nissan 350Z/Infiniti G35 1 2 22910252 Rear Sway Bar, 2003 Nissan 350Z/Infiniti G35 1 3 15.12.06.39 Universal Sway Bar Bracket 2 4 U-62345-BL 1 3/8" Factory Z style bushing 2 5 5339G 15/16" bushing 2 13 9.11108 Grease Pack 2 14 n/a Instruction Set 1 Items Not Shown
pA Front Sway Bar The larger Cosworth Sierra 28.5mm factory front sway bar is a direct replacement for the standard 25mm bar. (H.D. bar clamp bushings are included) M407 NOTE: see price list for sway bar clamp bushings for XR & Scorpio pB Spring Sets see page 3 (spring section) for
Front Sway Bar. Our sway bar will help remove the vehicles tendency to overpower the front tires under hard cornering and minimize traction robbing body lean. The CorkSport Mazdaspeed 3 Front Sway Bar allows you to fine tune the handling. We hope you enjoy your new part! Pl
How to Create a Microsoft Sway Presentation . Text and Images . Enter the text and photos or graphics you want to use to create the bones of your Sway presentation. You can enhance your Sway by incorporating a range of content types from numerous sources. 1. Select the template title and replace it with the title you want to give your Sway .
