R&S TSMA6B Battery Pack Getting Started
R&S TSMA6B-BPBattery Pack UnitGetting Started(a0èÊ2)4900906002Version 01
This document describes the following R&S TSMA6B accessory: R&S TSMA6B-BP Battery Pack Unit (4900.9001.20) R&S MNT-BP99WH Batteries (3660.9109.02) for R&S TSMA6B-BP 2021 Rohde & Schwarz GmbH & Co. KGMühldorfstr. 15, 81671 München, GermanyPhone: 49 89 41 29 - 0Email: info@rohde-schwarz.comInternet: www.rohde-schwarz.comSubject to change – data without tolerance limits is not binding.R&S is a registered trademark of Rohde & Schwarz GmbH & Co. KG.Trade names are trademarks of the owners.4900.9060.02 Version 01 R&S TSMA6B-BPThroughout this manual, products from Rohde & Schwarz are indicated without the symbol, e.g.R&S TSMA6B is indicated as R&S TSMA6B.
R&S TSMA6B-BPContentsContents1 Safety Information. 52 Documentation Overview.62.1 Getting Started Manual.62.2 Basic Safety Instructions. 62.3 Li-Ion Batteries Safety Instruction. 62.4 Data Sheets and Brochures. 63 Key Features. 84 Preparing for Use.94.1 Unpacking the Instrument.94.1.1 Hardware. 104.1.2 Standard Accessory. 114.1.3 Optional Accessory. 114.2 Connecting with External Power Supply. 124.3 Charging the Batteries. 134.4 Connecting R&S TSMA6B-BP with R&S TSMA6/6B. 154.5 Connecting R&S TSMA6B-BP with R&S TSME6 andR&S TSMExxDC. 174.6 Connecting the R&S TSMA6B-BP with Multiple Devices. 194.7 Disconnecting the R&S TSMA6B-BP from R&S TSMx Devices. 255 Instrument Tour. 275.1 Front Panel View. 275.2 Rear Panel View. 276 Operation.296.1 Operation Modes.29Getting Started 4900.9060.02 013
R&S TSMA6B-BPContents6.2 Power On/Off. 306.2.1 Auto Power On.306.2.2 Standby / Power On/Off. 306.3 Battery Charging.306.4 Automatic Power Path Switching.316.5 Monitoring Battery Charge State.316.5.1 Battery Charge Display. 316.5.2 Rear Panel LEDs. 336.5.3 R&S TSMA6/6B web-GUI / Tray Icon (Only Host-Controlled Mode). 346.6 Battery Exchange - Hot Swapping. 347 Contacting Customer Support. 36Index. 37Getting Started 4900.9060.02 014
R&S TSMA6B-BP1Safety InformationSafety InformationThe product documentation helps you use the R&S TSMA6B-BP safely and efficiently. Follow the instructions provided here and in the printed "Basic SafetyInstructions". Keep the product documentation nearby and offer it to other users.Intended useThe R&S TSMA6B-BP is intended for the development, production and verification of electronic components and devices in industrial, administrative, and laboratory environments. Use the R&S TSMA6B-BP only for its designated purpose.Observe the operating conditions and performance limits stated in the data sheet.Where do I find safety information?Safety information is part of the product documentation. It warns you about thepotential dangers and gives instructions how to prevent personal injuries or damage caused by dangerous situations. Safety information is provided as follows: The printed "Basic Safety Instructions" provide safety information in many languages and are delivered with the R&S TSMA6B-BP. Throughout the documentation, safety instructions are provided when youneed to take care during setup or operation.Getting Started 4900.9060.02 015
R&S TSMA6B-BPDocumentation OverviewData Sheets and Brochures2Documentation OverviewThis section provides an overview of the R&S TSMA6B-BP user documentation.Unless specified otherwise, you find the documents on the R&S TSMA6B-BPproduct page at:www.rohde-schwarz.com/manual/tsmx2.1Getting Started ManualIntroduces the R&S TSMA6B-BP and describes how to set up and start workingwith the product. Includes basic operations, typical measurement examples, andgeneral information, e.g. safety instructions, etc. A printed version is deliveredwith the instrument.2.2Basic Safety InstructionsContains safety instructions, operating conditions and further important information. The printed document is delivered with the instrument.2.3Li-Ion Batteries Safety InstructionContains safety instructions, operating conditions and further important information. The printed document is delivered with the instrument.2.4Data Sheets and BrochuresThe data sheet contains the technical specifications of the R&S TSMA6B-BP. Italso lists optional accessories.The brochure provides an overview of the instrument and deals with the specificcharacteristics.Getting Started 4900.9060.02 016
R&S TSMA6B-BPDocumentation OverviewData Sheets and BrochuresSee ng Started 4900.9060.02 017
R&S TSMA6B-BP3Key FeaturesKey FeaturesThe R&S TSMA6B-BP enhances the R&S TSMA6/6B device to a portable measurement solution based on a battery powered system.Key Features Power supply for R&S TSMA6/6B in portable applications Power supply for up to 4 additional devices (mobile network scanner R&STSME6 resp. downconverter R&S TSMExxDC*) Usage as a power buffer for connected devices in scenarios with cracking orshortly interrupted external DC power supplies / (e.g. in vehicles) Dual battery bay for hot-swap support and endless portable mode In-bay charging via smart battery controller Charge indicator LED for each individual battery bay Batteries (R&S MNT-BP99WH) have worldwide approval SMBus interface with connected R&S TSMA6/6B* R&S TSMExxDC includes the device types R&S TSME30DC and R&STSME44DC.Getting Started 4900.9060.02 018
R&S TSMA6B-BPPreparing for UseUnpacking the Instrument4Preparing for UseRisk of injury and instrument damageThe instrument must be used in an appropriate manner to prevent electricshock, fire, personal injury, or damage. Do not open the instrument casing. Read and observe the "Basic Safety Instructions" delivered as a printedbrochure with the instrument.In addition, read and observe the safety instructions in the following sections. Notice that the data sheet may specify additional operating conditions.Risk of instrument damage during operationAn unsuitable operating site or test setup can cause damage to the instrument and to connected devices. Ensure the following operating conditionsbefore you switch on the instrument: The instrument is dry and shows no sign of condensation. The instrument is positioned as described in the following sections. Signal levels at the input connectors are all within the specified ranges.4.1Unpacking the InstrumentRisk of instrument damage due to inappropriate operating conditionsSpecific operating conditions are required to ensure accurate measurements and to avoid damage to the instrument. Observe the information onappropriate operating conditions provided in the basic safety instructionsand the instrument's data sheet.Getting Started 4900.9060.02 019
R&S TSMA6B-BPPreparing for UseUnpacking the InstrumentCheck the equipment for completeness using the delivery note and the accessorylists for the various items. Check the instrument for any damage. If there is damage, immediately contact the carrier who delivered the instrument. Make sure notto discard the box and packing material.Packing materialRetain the original packing material. If the instrument needs to be transported or shipped later, you can use the material to protect the control elementsand connectors.4.1.1Hardware R&S TSMA6B-BPThe batteries are shipped separately with max. 30% of charge.NOTE: Before first usage, the batteries must be fully charged in theR&S TSMA6B-BP or with an external charger. Battery for R&S TSMA6B-BP (R&S MNT BP99WH, R&S No. 3660.9109.02)Getting Started 4900.9060.02 0110
R&S TSMA6B-BPPreparing for UseUnpacking the InstrumentFigure 4-1: R&S MNT-BP99WH4.1.2Standard AccessoryThe following items are included with shipment of the R&S TSMA6B-BP: DC power cable with a cigarette lighter adapter 4 x collar screws M2.5 for connecting R&S TSMA6/6B resp. R&S TSME6 /TSMExxDC Getting Started Manual (Printed) Safety instruction booklet Safety instruction Li-Ion batteries4.1.3Optional AccessoryThe following items are optional and must be ordered separately: R&S TSMA6-Z1 R&S No. 4901.0550.02AC power supply Additional Li-Ion battery (R&S MNT BP99WH, R&S No. 3660.9109.02 (seeFigure 4-1) External charger for batteries– R&S TSMA-BC2Dual charger for R&S TSMA6B-BP batteriesGetting Started 4900.9060.02 0111
R&S TSMA6B-BPPreparing for UseConnecting with External Power SupplyNOTE: Customer must provide country-specific power supply cable forIEC60320 / C6 socket.– R&S TSMA6-BC4, R&S No. 3630.7708.024-bay charger for R&S TSMA6B-BP batteries Collar screws (as a spare part) (R&S No. 4900.0804.00)To power TSMEx devices (scanner, downconverter), the following accessorycables are necessary. R&S TSMA6-BPPT (single TSMEx power cable, R&S No. 4900.1730.02) R&S TSMA6-BP2T (dual TSMEx power cable, R&S No. 4901.0566.02)4.2Connecting with External Power SupplyRisk of instrument damage during operationRead and observe the "Safety Instruction for rechargeable Li-Ion batteries"delivered as a printed brochure with the instrument.The DC power supply connector is on the rear panel. It has a wide range DCinput voltage from 11 V to 28 V.Figure 4-2: DC power supply connector DC power supply via cigarette lighter using the accessory DC power cable DC power supply from a vehicle terminal block with a modified DC powercableDemount the cigarette lighter adapter from the supplied power cable and connect the open ends of the cable to the proprietary power supply. Be sure torespect the correct polarity.Getting Started 4900.9060.02 0112
R&S TSMA6B-BPPreparing for UseCharging the BatteriesFigure 4-3: Supplied power cable with cigarette lighter adapter AC power supply via R&S TSMA6-Z1 (optional accessory)4.3Charging the BatteriesThe batteries are not charged on delivery. Before initial operation, the batteries must be fully charged without connected load (R&S TSMA6/6B, R&STSME6 reps. R&S TSMExxDC).For charging the batteries, users have two possibilities:In-bay charging in the R&S TSMA6B-BPInsert the batterie(s) in the correct way (charge indicator facing up). Take care ofthe nut in the battery and the pin inside the battery bay (see Chapter 6.6, "BatteryExchange - Hot Swapping", on page 34).Getting Started 4900.9060.02 0113
R&S TSMA6B-BPPreparing for UseCharging the BatteriesCharging starts automatically when DC power is connected. For checking thecharging state, see Chapter 6.5.2, "Rear Panel LEDs", on page 33.Charging with an external battery charger (optional accessory)The external recharging of the batteries is only allowed via the followingcharger types: R&S TSMA6-BC4, 4-bay charger R&S TSMA-BC2, 2-bay chargerTo check, if the batteries are fully charged, refer to Chapter 6.5.1, "Battery ChargeDisplay", on page 31.Then insert the batteries into the R&S TSMA6B-BP.Getting Started 4900.9060.02 0114
R&S TSMA6B-BPPreparing for UseConnecting R&S TSMA6B-BP with R&S TSMA6/6B4.4Connecting R&S TSMA6B-BP withR&S TSMA6/6BBefore initial operation, the batteries must be fully charged without anR&S TSMA6/6B connected (see Chapter 4.2, "Connecting with ExternalPower Supply", on page 12).To connect the R&S TSMA6/6B with the R&S TSMA6B-BP, the following stepsmust be performed.1. Remove the cover cap from the docking connector of the R&S TSMA6/6B.2. Screw the collar screws on the top of the R&S TSMA6B-BP with a Torx 8screw driver. Torque: 0.66 Nm 0.05 NmGetting Started 4900.9060.02 0115
R&S TSMA6B-BPPreparing for UseConnecting R&S TSMA6B-BP with R&S TSMA6/6BFigure 4-4: Collar screws1 Collar screws3. Align the collar screws with the snap-in holes on the bottom of anR&S TSMA6/6B and press the device down.Figure 4-5: Aligning R&S TSMA6B-BP and R&S TSMA6/6BGetting Started 4900.9060.02 0116
R&S TSMA6B-BPPreparing for UseConnecting R&S TSMA6B-BP with R&S TSME6 and R&S TSMExxDC1 R&S TSMA6B-BP2 Collar screws3 R&S TSMA6/6B4 Snap in holes on the bottom pane of R&S TSMA6/6B4. Move the R&S TSMA6/6B to the rear side (2) until you hear a click when thecollar screws are locked in.Figure 4-6: Connected R&S TSMA6B and R&S TSMA6-BP1 Attach R&S TSMA6/6B to R&S TSMA6B-BP2 Move R&S TSMA6/6B to the rear side3 Power connection established (docking connector is snapped in)4.5Connecting R&S TSMA6B-BP with R&S TSME6and R&S TSMExxDCThe following steps are valid for R&S TSME6 and downconverterR&S TSMExxDC.For the cabling of the devices, the accessory cables R&S TSMA6-BPPT orR&S TSMA6-BP2T are necessary.Getting Started 4900.9060.02 0117
R&S TSMA6B-BPPreparing for UseConnecting R&S TSMA6B-BP with R&S TSME6 and R&S TSMExxDCAdditional cabling may be necessary for proper operation. For completecabling instructions, refer to the R&S TSME6 User Manual and theR&S TSMExxDC Getting Started.1. Screw the collar screws (1) on the top of the R&S TSMA6B-BP with a Torx 8screw driver. Torque: 0.66 Nm 0.05 Nm1 Collar screws for connecting R&S TSME62 Aux 1 / Aux 2 (auxiliary power out for connecting R&S TSME6/TSMExxDC via powercable R&S TSME-ZYC)2. Align the collar screws with the snap-in holes on the bottom of an R&STSME6/TSMExxDC and press the device down.Figure 4-7: Example: Aligning R&S TSMA6B-BP and R&S TSME6Getting Started 4900.9060.02 0118
R&S TSMA6B-BPPreparing for UseConnecting the R&S TSMA6B-BP with Multiple Devices1 R&S TSMA6B-BP2 Collar screws3 R&S TSME6/TSMExxDC4 Snap-in holes on the bottom pane of R&S TSME6/TSMExxDC3. Move the R&S TSME6/TSMExxDC to the back side, until you hear a clickwhen the collar screws are locked in.Figure 4-8: Connected R&S TSME6/TSMExxDC and R&S TSMA6B-BP1 R&S TSMA6B-BP2 R&S TSME6/TSMExxDC4. Connect the power cable R&S TSMA6-BPPT resp. R&S TSMA6-BP2T fromAUX1 resp. AUX2 to DC IN of R&S TSME6/xxDC (see Figure 4-10).4.6Connecting the R&S TSMA6B-BP with MultipleDevicesAdditional cabling may be necessary for proper operation. For completecabling instructions, refer to the R&S TSME6 User Manual and theR&S TSMExxDC Getting Started.The R&S TSMA6B-BP can be connected with several devices at the same time.In the following, examples for such multiple device combinations are shown.The connection of up to 4 R&S TSME6/TMSExxDC devices is possible. For up to 2 devices, 1 x R&S TSMA6-BP2T dual power cable or 2 x R&STSMA6 BPPT single power cables are required.Getting Started 4900.9060.02 0119
R&S TSMA6B-BPPreparing for UseConnecting the R&S TSMA6B-BP with Multiple Devices For up to 4 devices, 2 x R&S TSMA6-BP2T dual power cables are required.Per device, 4 collar screws are required.4 collar screws are part of the standard accessory of the R&S TSMA6B-BP.Additional collar screws are part of the R&S TSME6/TSMExxDC accessoryor can be ordered as spare parts (R&S no. 4900.0804.00).Setup with TSMA6B-BP TSMA6/6B Downconverter TSMExxDCFigure 4-9: TSMA6B-BP TSMA6/6B downconverter TSMExxDCSetup with TSMA6B-BP TSME6 TSMExxDCConnect up to two R&S TSME6/TSMExxDC. Use one of the following solutions. Connect the devices with 2 x R&S TSMA6-BPPT single power cables toAUX1 and AUX2 port of the R&S TSMA6B-BP (see Figure 4-10). Connect the devices with 1 x R&S TSMA6-BP2T dual power cable to AUX1 orAUX2 port of the R&S TSMA6B-BP (see Figure 4-16).Getting Started 4900.9060.02 0120
R&S TSMA6B-BPPreparing for UseConnecting the R&S TSMA6B-BP with Multiple DevicesFigure 4-10: TSMA6B-BP TSME6 TSMExxDCTo connect the R&S TSME6 and the R&S TSMExxDC with the R&S TSMA6B-BP,the following steps must be performed.4 collar screws are part of the standard accessory of the R&S TSMA6B-BP.Additional collar screws are part of the R&S TSME6/TSMExxDC accessoryor can be ordered as spare parts (R&S no. 4900.0804.00).1. Screw the collar screws on the top of the R&S TSMA6B-BP with a Torx 8screw driver. Torque: 0.66 Nm 0.05 NmGetting Started 4900.9060.02 0121
R&S TSMA6B-BPPreparing for UseConnecting the R&S TSMA6B-BP with Multiple DevicesFigure 4-11: Collar screws1 8 x Collar screws (R&S No.4900.0804.00)2. Align the collar screws with the snap-in holes on the bottom of the R&STSME6 and R&S TSMExxDC and press these devices down.Figure 4-12: Aligning R&S TSMA6B-BP, R&S TSME6 and R&S TSMExxDCGetting Started 4900.9060.02 0122
R&S TSMA6B-BPPreparing for UseConnecting the R&S TSMA6B-BP with Multiple Devices1 R&S TSMA6B-BP2 Collar screws3 R&S TSME64 Snap-in holes on the bottom pane of R&S TSME6 and R&S TSMExxDC5 R&S TSMExxDC3. Connect DC power cable R&S TSMA6-BPP1 resp. R&S TSMA6-BP2T fromAUX1 / AUX2 to the DC IN socket of the devices (see Figure 4-13).Setup with TSMA6B-BP 2 x TSME6 TSMExxDCFigure 4-13: TSMA6B-BP 2 x TSME6 TSMExxDCTo connect 3 and 4 R&S TSME6/TSMExxDC devices, proceed as follows.1. Mount the devices 1 and 2 according to steps described in Chapter 4.5, "Connecting R&S TSMA6B-BP with R&S TSME6 and R&S TSMExxDC",on page 17.2. For the devices 3 and 4, screw the additional collar screws on top of thealready mounted devices.Getting Started 4900.9060.02 0123
R&S TSMA6B-BPPreparing for UseConnecting the R&S TSMA6B-BP with Multiple DevicesFigure 4-14: Aligning R&S TSMA6B-BP, 2x R&S TSME6 and R&S TSMExxDC1 Collar screws3. Align the collars with the snap-in holes on the bottom of the additional devicesand press these devices down.Figure 4-15: Aligning R&S TSME6/TSMExxDCs1 1st R&S TSME6/TSMExxDC2 Collar screws3 2nd R&S TSME6/TSMExxDC Snap-in holes on the bottom pane of R&S TSME6/TSMExxDCGetting Started 4900.9060.02 0124
R&S TSMA6B-BPPreparing for UseDisconnecting the R&S TSMA6B-BP from R&S TSMx Devices4. Connect DC power cable R&S TSMA6-BPP1 resp. R&S TSMA6-BP2T fromAUX1 / AUX2 to the DC IN socket of the devices (seeFigure 4-13 ).Setup with TSMA6B-BP TSMA6/6B TSME6 TSMExxDCFigure 4-16: TSMA6B-BP TSMA6/6B TSME6 TSMExxDC4.7Disconnecting the R&S TSMA6B-BP from R&STSMx DevicesTo disconnect the R&S TSMA6B-BP and R&S TSMx d
Getting Started 4900.9060.02 01 11 Figure 4-1: R&S MNT-BP99WH 4.1.2 Standard Accessory The following items are included with shipment of the R&S TSMA6B-BP: DC power cable with a cigarette lighter adapter 4 x collar screws M2.5 for connecting R&S TSMA6/6B resp. R&S TSME6 / TSMExxDC Getting Started Manual (Printed)
Learning About the Reader’s Batteries 2-34 Lithium Backup Battery 2-34 NiCad Battery Pack 2-35 Installing the Battery Pack 2-35 Removing the Battery Pack 2-36 Checking the Power Remaining in the NiCad Battery Pack 2-38 Charging the Battery Pack 2-39 Disposing of the NiCad Battery Pack 2-39 Recognizing a Low or Discharged Battery 2-40
INSTALLING OR REMOVING BATTERY PACK TO REMOVE BATTERY PACK: Depress the battery pack release button (6) and pull the battery pack (7) out of tool. TO INSTALL BATTERY PACK: Push the battery pack (7) onto tool until it locks in place. INSTALLING SOCKETS Always follow the procedure below to install a socket. 1. Insert a socket into the anvil (1). 2.
The maximum ambient temperature in which a Battery System should be operated is 104 F (40 C). The nominal battery voltage for the battery cabinet is as follows: Model Voltage H3B-BC-1825 288 VDC Table 1 Battery Pack Information Battery Pack Data Battery Packs Designed for battery acid leakage containment with (6) batteries per pack.
2. Tighten the Battery Pack Mounting Clamps with a screw driver. Remove excess tail from the clamp. 3. Place the battery in the holder. Secure the battery to the base with the nylon strap. 4. 4.Attach the power cord from the battery to the power input on the lift. Operation Before using the battery pack for the first time, verify that the
paws. Family, friends, neighbors, co-workers, and anyone who believes in the humane treatment of animals can be a part of YOUR PACK! Determine a Pack Leader & Pack Name: The Pack Leader will be responsible for coordinating all Pack paperwork, keeping the Pack informed, motivating the Pack to FUNdraise, and ensuring the minimum 1,000 is collected.
Battery Status: To check the battery charge status, turn on the battery power by switching “On” the Battery Power Switch. Please do not let the battery fully die, this severly shortens the life of the battery. Battery Recharge: It will take about 4 hours to reach full charge. To recharge the battery, plug the supplied power supply into the
On-Battery - The Back-UPS is supplying battery power. Low Battery - The Back-UPS is supplying battery power and the battery is near a total discharge state. Replace Battery Detected - The battery needs to be charged, or is at end of life. Low Battery Shutdown - During On Battery operation Back-UPS BX Series 750VA, 950VA, 1200VA, 1600VA, 2200VA
ANIMAL NUTRITION Tele-webconference, 27 November, 10 and 11 December 2020 (Agreed on 17 December 2020) Participants Working Group Members:1 Vasileios Bampidis (Chair), Noël Dierick, Jürgen Gropp, Maryline Kouba, Marta López-Alonso, Secundino López Puente, Giovanna Martelli, Alena Pechová, Mariana Petkova and Guido Rychen Hearing Experts: Not Applicable European Commission and/or Member .
