SPEC-00385L763.422.2211763.422.2600 DiSConneCt StainleSS Steel HeaVY .
Free-Stand Stainless Steel Preferred-Cutout Disconnects Stainless Steel Heavy Duty DisconnectsDISCONNECTFREE-STAND STAINLESS STEEL PREFERRED-CUTOUT DISCONNECTSSTAINLESS STEEL HEAVY DUTY NLESS STEEL HEAVY-DUTY FREE-STAND ENCLOSURES FOR FLANGE-MOUNT DISCONNECTS, TYPE 4Xpetroleum and chemical processing industries. Designed to housethe most popular disconnect switches and circuit breakers.SPECIFICATIONS anufactured from 12 gauge Type 304 stainless steelM S eams continuously welded and ground smooth Body stiffeners in larger enclosures for extra rigidity Body flange trough collar excludes liquids and contaminants Heavy-duty lifting eyes anchor into reinforced top Removable centerposts permit easy panel installation Heavy-gauge continuous hinges Heavy-duty 3-point latching mechanism operated by Type 316Lstainless steel POWERGLIDE padlocking handle on all doors P anel supports Data pocket is high-impact thermoplastic S eamless foam-in-place gasket provides oil-tight and dust-tightseal against contaminants Removable 10 gauge steel panels mount on collar studs Master door is far right-hand door on all enclosures Type 316 stainless steel handle with defeater on master door Type 316 stainless steel handle (non-defeater) on slave door Mechanical interlock activated by master door prevents slavedoors from being opened first. Doors can be closed in any order. Preferred cutout on right flange provides mounting for mostdisconnect operators Bonding provision on doors; grounding studs on body Accessory mounting channel provided in enclosure topFINISHStainless steel enclosures are unpainted. Sides and body havesmooth #4 brushed finish. White mild steel panels are furnishedwith enclosure. Optional conductive panels are available.ACCESSORIESINDUSTRY STANDARDSUL 508A Listed 508; Type 3R, 4, 4X, 12; File No. E61997cUL Listed per CSA C22.2 No. 94; Type 3R, 4, 4X, 12; File No.E61997NEMA/EEMAC Type 3R, Type 4, 4X, 12CSA File No. 42186: Type 4, 4X, 12IEC 60529, IP66Meets NEMA Type 3RX requirementsAPPLICATIONMODIFICATION AND CUSTOMIZATIONHoffman excels at modifying and customizing products to yourspecifications. Contact your local Hoffman sales office or distributorfor complete information.This disconnect enclosure is designed to house electronic controlsand components. It provides protection from noncorrosive or mildlycorrosive elements in both indoor and outdoor environments.Typical applications are in the food and beverage, packaging, water,1DisconnectSee also Accessories.Electric HeaterCompact Cooling FansFloor Stand KitPANELITE Enclosure Lights OverviewOperator Adapters for Preferred CutoutsAn operator adapter for a preferred cutout must be ordered separately.PATENTSUS 5,634,357D 385,7683BULLETIN: A28S4SUBJECT TO CHANGE WITHOUT NOTICEEQUIPMENT PROTECTIONSpec-00385 L
Free-Stand Stainless Steel Preferred-Cutout Disconnects Stainless Steel Heavy Duty DisconnectsStandard Product One-Door EnclosuresCatalog XM4024SSN4AxBxC in.72.12 x 28.25 x 18.1272.12 x 34.25 x 18.1272.12 x 40.25 x 18.1284.12 x 40.25 x 18.1290.12 x 40.25 x 18.1290.12 x 40.25 x 20.1284.12 x 40.25 x 24.1290.12 x 40.25 x 24.12AxBxC mm1832 x 718 x 4601832 x 870 x 4601832 x 1022 x 4602137 x 1022 x 4602289 x 1022 x 4602289 x 1022 x 5112137 x 1022 x 6132289 x 1022 x A84PM40A90PM40Conductive 40GA84PM40GA90PM40GPanel Size (in.)60.00 x 21.7560.00 x 27.7560.00 x 33.7572.00 x 33.7578.00 x 33.7578.00 x 33.7572.00 x 33.7578.00 x 33.75Panel Size (mm)1524 x 5521524 x 7051524 x 8571829 x 8571981 x 8571981 x 8571829 x 8571981 x 857White mild steel panels are furnished with enclosure. Purchase conductive panels separately.All 24.12-in. (613-mm) and deeper enclosures using short connecting rods in the following models require a Hoffman platform assembly, catalog number ADSCPA, purchased separately. ABB Controls flange-operateddevices Cutler-Hammer C361 devices Cutler-Hammer C371 mechanisms which use C371E, F, G, K operating mechanism General Electric Type TDA devices (see next paragraph for option) Square D Class 9422 devices(see next paragraph for option)The platform assembly can be omitted if long connecting rods are ordered in place of short connecting rods. For Cutler-Hammer operating mechanisms C371E and C371F order catalog number C371CS1 connecting rod.For C371G and C371K order catalog number C371CS2 connecting rod. For General Electric devices, order catalog number TDSR extended length drive rod For Square D devices, order catalog number 9422-R2 extra longoperating rod(s). Some devices require two rods. Consult factory for space occupied on panel when platform is used.EQUIPMENT PROTECTIONSpec-00385 LPH 763.422.2211 FAX 763.422.2600 pentairprotect.comDisconnect2
Free-Stand Stainless Steel Preferred-Cutout Disconnects Stainless Steel Heavy Duty DisconnectsStandard Product Two-Door EnclosuresCatalog XM7824SSN4A90XM7824SSN4AxBxC in.72.12 x 54.50 x 18.1272.12 x 66.50 x 18.1272.12 x 78.50 x 18.1284.12 x 78.50 x 18.1290.12 x 78.50 x 18.1290.12 x 78.50 x 20.1272.12 x 78.50 x 24.1284.12 x 78.50 x 24.1290.12 x 78.50 x 24.12AxBxC mm1832 x 1384 x 4601832 x 1689 x 4601832 x 1994 x 4602137 x 1994 x 4602289 x 1994 x 4602289 x 1994 x 5111832 x 1994 x 6132137 x 1994 x 6132289 x 1994 x A72PM78A84PM78A90PM78Conductive 78GA72PM78GA84PM78GA90PM78GPanel Size (in.)60.00 x 48.0060.00 x 60.0060.00 x 72.0072.00 x 72.0078.00 x 72.0078.00 x 72.0060.00 x 72.0072.00 x 72.0078.00 x 72.00Panel Size (mm)1524 x 12191524 x 15241524 x 18291829 x 18291981 x 18291981 x 18291524 x 18291829 x 18291981 x 1829White mild steel panels are furnished with enclosure. Purchase conductive panels separately.3DisconnectSUBJECT TO CHANGE WITHOUT NOTICEEQUIPMENT PROTECTIONSpec-00385 L
Free-Stand Stainless Steel Preferred-Cutout Disconnects Stainless Steel Heavy Duty DisconnectsStandard Product Three-Door EnclosuresCatalog 4XM3EW24SSN4A90XM3EW24SSN4AxBxC in.72.12 x 100.75 x 18.1272.12 x 118.75 x 18.1284.12 x 118.75 x 18.1284.12 x 118.75 x 24.1290.12 x 118.75 x 24.12AxBxC mm1832 x 2559 x 4601832 x 3016 x 4602137 x 3016 x 4602137 x 3016 x 6132289 x 3016 x A90PM78GNumber ofLargePanels11111Size ofLargePanels (in.)60.00 x 60.0060.00 x 72.0072.00 x 72.0072.00 x 72.0078.00 x 72.00Size ofLargePanels (mm)1524 x 15241524 x 18291829 x 18291829 x 18291981 x GA90PM40GNumber ofSmallPanels11111Size ofSmallPanels (in.)60.00 x 27.7560.00 x 33.7572.00 x 33.7572.00 x 33.7578.00 x 33.75Size ofSmallPanels (mm)1524 x 7051524 x 8571829 x 8571829 x 8571981 x 857White mild steel panels are furnished with enclosure. Purchase conductive panels separately.EQUIPMENT PROTECTIONSpec-00385 LPH 763.422.2211 FAX 763.422.2600 pentairprotect.comDisconnect4
Free-Stand Stainless Steel Preferred-Cutout Disconnects Stainless Steel Heavy Duty DisconnectsStandard Product Four- and Five-Door EnclosuresCatalog BxC in.72.12 x 158.00 x 18.1284.12 x 158.00 x 18.1284.12 x 197.75 x 24.12AxBxC mm1832 x 4013 x 4602137 x 4013 x 4602137 x 5023 x 613Number ofDoors445PanelA72PM78A84PM78A84PM78 and A84PM40Numberof Panels222 and 1Size ofPanels (in.)60.00 x 72.0072.00 x 72.0072.00 x 72.00 and 72.00 x 33.75Sizes ofPanels (mm)1524 x 18291829 x 18291829 x 1829 and 1329 x 857White mild steel panels are furnished with enclosure. Optional conductive panels are available.All 24.12-in. (613-mm) and deeper enclosures using short connecting rods in the following models require a Hoffman platform assembly, catalog number ADSCPA, purchased separately. ABB Controls flange-operateddevices Eaton Cutler-Hammer C361 devices Eaton Cutler-Hammer C371 mechanisms which use C371E, F, G, K operating mechanism General Electric Type TDA devices (see next paragraph for option) SchneiderSquare D Class 9422 devices (see next paragraph for option)The platform assembly can be omitted if long connecting rods are ordered in place of short connecting rods. For Eaton Cutler-Hammer operating mechanisms C371E and C371F order catalog number C371CS1 connectingrod. For C371G and C371K order catalog number C371CS2 connecting rod. For General Electric devices, order catalog number TDSR extended length drive rod For Schneider Square D devices, order catalog number 9422R2 extra long operating rod(s). Some devices require two rods. Consult factory for space occupied on panel when platform is used.5DisconnectSUBJECT TO CHANGE WITHOUT NOTICEEQUIPMENT PROTECTIONSpec-00385 L
Free-Stand Stainless Steel Preferred-Cutout Disconnects Stainless Steel Heavy Duty DisconnectsEQUIPMENT PROTECTIONSpec-00385 LPH 763.422.2211 FAX 763.422.2600 pentairprotect.comDisconnect6
Free-Stand Stainless Steel Preferred-Cutout Disconnects Stainless Steel Heavy Duty DisconnectsDISCONNECT MOUNTING SPACEDisconnects will occupy space on panel shown by dimensionsE1, F1 and G1 in the diagram. Wiring space W1 is available whendisconnect is installed in the enclosure.See the Technical Information section for E1 Spacing by EnclosureHeight for various disconnect switch manufacturers.Refer to National Electrical Code , 2005 article 430-10(b) forwiring space required for line side conductors to be connected todisconnect.Verify your application to determine if wiring space is adequate.A Complete Assembly Consists of:1. An enclosure2. A panel3. An operator adapter (see Disconnect Enclosure Accessoriesin this publication to select the proper operator adapter forthe brand and type of disconnect being used). Door hardwareis furnished with enclosure.4. A disconnect device.All 24.12-in. (613-mm) and deeper enclosures using shortconnecting rods by the following manufacturers require a Hoffmanplatform assembly, catalog number ADSCPA, purchased separately. A BB Controls flange-operated devices E aton Cutler-Hammer C361 devices E aton Cutler-Hammer C371 mechanisms which use C371E, F, G,K operating mechanism (see Disconnect Enclosure Accessories) G eneral Electric Type TDA devices (see Disconnect EnclosureAccessories) S chneider Square D Class 9422 devices (see DisconnectEnclosure Accessories)The platform assembly can be omitted if long connecting rods areordered in place of short connecting rods. For Eaton Cutler-Hammer operating mechanisms C371E andC371F order catalog number C371CS1 connecting rod. For C371Gand C371K order catalog number C371CS2 connecting rod. For General Electric devices, order catalog number TDSRextended length drive rod For Schneider Square D devices, order catalog number 9422-R2extra long operating rod(s). Some devices require two rods.Consult factory for space occupied on panel when platform is used.7DisconnectSUBJECT TO CHANGE WITHOUT NOTICEEQUIPMENT PROTECTIONSpec-00385 L
tOverviewPREFERRED-CUTOUT OVERVIEWFREE-STAND PREFERRED-CUTOUT STAINLESS STEEL DISCONNECT OVERVIEW ulletin 140U flexible cable operating mechanisms for 140UBmolded case circuit breakers Bulletin 140G flexible cable and variable depth flange-mountmolded case circuit breakers Bulletin 1494C cable-operated disconnect switches with flangemount handles Bulletin 194RC cable-operated flange-mount handles for use withthe NFPA 79 compliant 194R IEC rotary disconnect switchesAllen-Bradley Bulletin 1494V-R1, -R2 and -W2 operating handles andAllen-Bradley Bulletin 1494F disconnect devices or Bulletin 1494D circuitbreaker operators will NOT fit these enclosures. ABB Controls flange-mount variable-depth operating mechanismsfor disconnect switches and circuit breakers. Also the cable versionfor circuit breakers.Eaton Cutler-Hammer Type C361 flange-mount variable-depthoperating mechanisms with disconnect switches and Type C371flange-mount variable-depth operating mechanisms for circuitbreakers.APPLICATIONEnclosures having the preferred cutout are sized for use withup to 200A disconnect switches and up to 400A circuit breakersunless otherwise specified. The preferred cutout accepts thesmaller operating handle whose mounting hole centers are 4.688in. apart. Preferred cutouts are standard in mild steel wall-mountenclosures, modular enclosures and some select large mild steelenclosures. They are also present on all standard stainless steelofferings. 400 A (or greater) disconnect switches and 600 A (orgreater) circuit breakers require the “Large” or “High Amp” cutout.This cutout accepts the larger operating handle whose mountinghole centers are 6.500-in. apart. This large cutout is only availableon PROLINE-DD Disconnect Packages and Type 1 Free-StandEnclosures.Operator adapter for preferred cutouts must be ordered separatelyto be used with A21S, A28S4, A4S and WS2D enclosures. Preferredcutouts are designed to house the following:Allen-Bradley Bulletin 1494V disconnect switches with flange-mount variabledepth operating mechanisms and Bulletin 1494V flange-mountvariable-depth operating mechanisms for circuit breakersEQUIPMENT PROTECTIONSpec-00385 LGeneral Electric Type STDA flange handles and variable-depthoperating mechanisms for disconnect switches and circuitbreakers. Also SPECTRAFLEX cable operators for circuit breakers.Siemens ITE MAX FLEX flange-mount variable-depth operatinghandles for circuit breakers.Schneider Square D Class 9422 disconnect switches with flangemount variable-depth operating mechanisms or cable mechanismsand Class 9422 flange-mount variable-depth operating mechanismsor cable mechanisms for circuit breakers.These enclosures will NOT accept Square D Class 9422 bracketmounted disconnect devices, Class 9422TG1 or TG2 devices.ORDERINGOrder the disconnect switch, operating handle and operatingmechanism separately. See Technical Information in the HoffmanSpecifier’s Guide for wire bend space available when variousmanufacturers’ disconnect switches are installed or DisconnectOrdering Information at pentairprotect.com for disconnect orderingguidelines and wire bend space available. Check the enclosuredimension drawings to verify the chosen disconnect switch will fit inthe enclosure.PH 763.422.2211 FAX 763.422.2600 pentairprotect.comDisconnect8
Free-Stand Stainle SS Steel PreFerred-Cutout d iSConneCtS StainleSS Steel Heavy Duty Di SconnectS Spec-00385 L 1 diSConneCt SuBJeCt to CHanGe WitHout notiCe eQuiPMent ProteCtion SPEC-00385L763.422.2211763.422.2600 . All 24.12-in. (613-mm) and deeper enclosures using short connecting rods in the following models require a Hoffman platform .
Spec-00583G763.422.2211763.576.3200 cooling Accessories controllers ThermosTAT conTroller . These easy-to-install thermostats regulate and monitor air temperature in enclosures that contain heat-emitting equipment. Thermostats prolong heater and fan life expectancy by controlling
Spec-00583H763.422.2211763.576.3200 Therm Al mAn gemenT Accessories controllers ThermosTAT conTroller . These easy-to-install thermostats regulate and monitor air temperature in enclosures that contain heat-emitting equipment. Thermostats prolong heater and fan life expectancy by control
Spec-00724 E Wall-Mount Cabinets PROTEK Singl E-DOOR anD DOublE-HingED CabinETS 3 netWorking SUBJECT TO CHANGE WITHOUT NOTICE EQUIPMENT PROTECTION SOLUTIONS Standard Product Protek Double-Hinged Window Door, t ype 1 (indoor only) Catalog Number AxBxC in./mm Rack Units P in./mm Q in./mm Optional Steel Panel Optional Wood Panel Additional Rack Anglesa .
Sealed encloSure cooling Air Conditioners Spec-01233 E 1 Thermal managemen T SUBJECT TO CHANGE WITHOUT NOTICE PEntair ElEctrical SPEC-01233E763.422.2211763.576.3200 Thermal managemen SEALED ENCLOSURE COOLING AIR CONDITIONERS SPecTracool corroSion ProTecTion oVerVieW
eQUiPMenT ProTecTion PH 763.422.2211 FAX 763.576.3200 HOFFMANONLINE.COM cooling 8 HAZArDoUs locATion HeATer inDUsTrY sTAnDArDs CE Conformity Certificate LCIE (Laboratoire Central des Industries Electriques) LCIE 01 ATEX 6073 EEx d IIC T4/II 2 GD, IP6x T135 C IEC 60529, IP65/I (grounded) APPlicATion
EmC shielding Clear plated components (exterior painted) and a conductive fabric-over-foam gasket provide an HF2 level of shielding. door Bars Door bars are included inside all PROLINE doors taller than 700 mm and wider than 400 mm (except window doors). These sturdy door bars provide maximum rigidity and can be used for mounting accessories.
Sealed encloSure cooling Air Conditioners Spec-00733 D 1 cooling SuBJecT To cHange WiTHouT noTice eQuipmenT proTecTion Spec-00733D763.422.2211763.576.3200 cooling . elecTrical daTa rated Voltage 100/115 220/230 Frequency (Hz) 50/60 50/60 Operating Range /- 10% /- 10% Max. Power Consumption (W at 50/60 Hz) 360/403 330/345
4 ASTM D 4255 Two-Rail Shear Test 4 5 ASTM D 4255 Three-Rail Shear Test 5 6 Iosipescu (V-Notched) Shear Test Fixture and Specimen 6 7 Compact Shear Test Fixture and Specimen 6 8 Orientation of Finite Element Model 8 9 Initial Rectangular Specimen Investigated 10 10 Initial Trapezoidal Specimen Investigated 10 11 Standard Tab Specimen Configuration 12 12 Extended Tab Specimen Configuration 12 .
