Synergy TRU-Balance INSTALLATION AND CARE INSTRUCTIONS Synergy Shape .
Synergy TRU-Balance INSTALLATION AND CARE INSTRUCTIONS Power Tilt Shape Back Synergy Synergy Shape Back TM ACN# 088 609 661 ACN# 088 609 661
SAFETY GUIDELINES WARNING! A Quantum Rehab Specialist or a qualified technician must perform the initial setup of this product and must perform all of the instructions in this manual. The symbols below are used throughout this owner's manual and on the product to identify warnings and important information. It is very important for you to read them and understand them completely. WARNING! Indicates a potentially hazardous condition/ situation. Failure to follow designated procedures can cause either personal injury, component damage, or malfunction. On the product, this icon is represented as a black symbol on a yellow triangle with a black border. MANDATORY! These actions should be performed as specified. Failure to perform mandatory actions can cause personal injury and/or equipment damage. On the product, this icon is represented as a white symbol on a blue dot with a white border. PROHIBITED! These actions are prohibited. These actions should not be performed at any time or in any circumstances. Performing a prohibited action can cause personal injury and/or equipment damage. On the product, this icon is represented as a black symbol with a red circle and a red slash. NOTE: These instructions are compiled from the latest specifications and product information available at the time of publication. We reserve the right to make changes as they become necessary. Any changes to our products may cause slight variations between the illustrations and explanations in this manual and the product you have purchased. The latest/current version of this manual is available on our website. 088 609 661 Copyright 2007 Pride Mobility Products Corporation INFMANU2873/Rev C/June 2007 Synergy Shape Back www.quantumrehab.com
TABLE OF CONTENTS LABEL INFORMATION . 4 INTRODUCTION . 5 THE SYNERGY SHAPE BACK . 7 MOUNTING BRACKET COMPONENTS . 9 INSTALLATION AND USE . 10 COMFORT ADJUSTMENTS . 12 REMOVING THE SYNERGY SHAPE BACK . 17 CLEANING . 17 STORAGE . 19 CARE AND MAINTENANCE . 19 WARRANTY . 19 www.quantumrehab.com Synergy Shape Back
4 Installation and Care Instructions LABEL INFORMATION PRODUCT SAFETY SYMBOLS The symbols below are used on the product to identify warnings, mandatory actions, and prohibited actions. It is very important for you to read and understand them completely. Read and follow the information in the owner’s manual. Synergy Shape Back www.quantumrehab.com
Installation and Care Instructions 5 INTRODUCTION WELCOME to Quantum Rehab, a division of Pride Mobility Products Corporation (Pride). The product you have purchased combines state-of-theart components with safety, comfort, and styling in mind. We are confident that the design features will provide you with the conveniences you expect during your daily activities. Understanding how to safely use and care for this product should bring you years of trouble free operations and service. Read and follow all instructions, warnings, and notes in this manual and all other accompanying literature before attempting to use this product for the first time. In addition, your safety depends upon you, as well as your provider, caretaker, or healthcare professional in using good judgement. This manual is to be used in addition to the owner’s manual that came with your chair. If there is any information in this manual which you do not understand, or if you require additional assistance for setup or operation, please contact your Quantum Rehab Specialist. Failure to follow the instructions, warnings, and notes in this manual and those located on your Pride product can result in personal injury and/or product damage and will void Pride’s product warranty. PURCHASER’S AGREEMENT By accepting delivery of this product, you promise that you will not change, alter, or modify this product or remove or render unusable or unsafe any guards, shields, or other safety features of this product; fail, refuse, or neglect to install any retrofits kits from time to time provided by Pride to enhance or preserve the safe use of this product. INFORMATION EXCHANGE We want to hear your questions, comments, and suggestions about this manual. We would also like to hear about the safety and reliability of your new Pride product, and about the service you received from your Quantum Rehab Specialist. Please notify us of any change of address, so we can keep you apprised of important information about safety, new products, and new options that can increase your ability to use and enjoy your Pride product. www.quantumrehab.com Synergy Shape Back
6 Installation and Care Instructions Please feel free to contact us at the address below: Pride Mobility Products Corporation Attn: Customer Care Department 182 Susquehanna Avenue Exeter, PA 18643-2694 NOTE: If you ever lose or misplace your product registration card or your copy of this manual, contact us and we will be glad to send you a new one immediately. My Quantum Rehab Specialist Is: Name: Address: Phone Number: Purchase Date: Synergy Shape Back www.quantumrehab.com
Installation and Care Instructions 7 THE SYNERGY SHAPE BACK The Synergy Shape Back is a unique seatback cushion that is available in standard, tall, and low versions and is fully adjustable for user comfort and positioning needs. Figures 1 and 2 provide information on the Synergy Shape Back components and cushions. Use this diagram to familiarize yourself with the function and location of each component before using the Synergy Shape Back. RELEASE LEVER HANDLE Used to quickly unlock your Synergy Shape Back mounting blocks from the mounting brackets. CARRYING HANDLE Used for ease in carrying your Synergy Shape Back. LATERAL SUPPORTS Optional lateral supports can be adjusted for both width and depth. SYNERGY SHAPE BACK LOW Lower version of Synergy Shape Back. SYNERGY SHAPE BACK TALL Higher version of Synergy Shape Back. MOUNTING BLOCKS Receivers for the mounting brackets; can also be used to adjust the width of your Synergy Shape Back. MOUNTING BRACKETS AND T-SLOT ADAPTERS Used to mount Synergy Shape Back to the back canes of your chair. Can also be used to adjust the height, depth, and recline angle of your Synergy Shape Back. Figure 1. Synergy Shape Back Components www.quantumrehab.com Synergy Shape Back
8 Installation and Care Instructions Synergy Shape Back Cushion Synergy Shape Back Tall Cushion Figure 2. Synergy Shape Back Cushions Synergy Shape Back www.quantumrehab.com Synergy Shape Back Low Cushion
Installation and Care Instructions 9 MOUNTING BRACKET COMPONENTS The mounting bracket components consist of a mounting pin, a positioning screw, and a safety setscrew. See figures 3 and 4. Moving the Mounting Pin The mounting pin can be used in either the front or back of the mounting bracket and works with the positioning screw to set the Synergy Shape Back at the desired recline angle and seat depth. The safety setscrew must be removed before the mounting pin can be removed and must be reinstalled once the mounting pin is in place. To maximize seat depth, position the mounting pins in the back of the mounting bracket. See figure 3. To minimize seat depth, position the mounting pins in the front of the mounting brackets. See figure 4. To maximize recline, position the top mounting pins in the back of the mounting bracket and the bottom mounting pins in front of the mounting bracket. For more information regarding seat adjustments, see “Comfort Adjustments.” WARNING! Make sure the safety setscrew is tightly in place before using the Synergy Shape Back. NOTE: There will be some resistance when removing the safety setscrew. POSITIONING SCREW POSITIONING SCREW MOUNTING BRACKET MOUNTING PIN MOUNTING PIN MOUNTING BRACKET SAFETY SETSCREW Figure 3. Back Mounting Pin Location SAFETY SETSCREW Figure 4. Front Mounting Pin Location www.quantumrehab.com Synergy Shape Back
10 Installation and Care Instructions INSTALLATION AND USE WARNING! Make sure the safety setscrew is tightly in place before using the Synergy Shape Back. NOTE: Seatback recline angle, depth, width, and height may be set prior to mounting the Synergy Shape Back on the chair. See “Comfort Adjustments.” To install the Synergy Shape Back on chairs with solid back canes: WARNING! Prolonged exposure to the mounting band may cause skin irritation. Avoid prolonged contact. 1. Locate the “L” or “R” label on the mounting bracket. The bracket marked “L” is for use on the left side and the bracket marked “R” is for use on the right side. The right bracket is shown in figure 5 for reference. 2. Hold the Synergy Shape Back up to the desired height on the seat canes and make note of where the mounting brackets will be located. 3. Starting on one side, wrap the mounting band of the top bracket around the back cane so the mounting band is on the bottom. Fasten the mounting screw into the receiver. See figure 5. 4. Wrap the bottom mounting band marked for that side around the back cane so the mounting band is on the bottom. Fasten the mounting screw into the receiver. See figure 5. 5. Repeat for the other side. WARNING! Ensure the hardware is tight. Synergy Shape Back www.quantumrehab.com RECEIVER MOUNTING BAND SEAT CANE MOUNTING SCREW TIGHTEN MOUNTING SCREW Figure 5. Mounting Bracket Installation on Solid Canes
Installation and Care Instructions 11 6. Once the mounting brackets are in place, stand behind the chair and align the bottom mounting block on the seatback with the mounting pin on the bottom mounting bracket. Make sure to angle the seatback forward. See figure 7. Rotate the seatback backwards until it clicks into place. NOTE: The zipper on the cushion will face the rear of the seat. To install the Synergy Shape Back on chairs with T-slotted back canes: WARNING! Prolonged exposure to the mounting band may cause skin irritation. Avoid prolonged contact. 1. Locate the “L” or “R” label on the mounting bracket. The bracket marked “L” is for use on the left side and the bracket marked “R” is for use on the right side. The right bracket is shown in figure 6 for reference. 2. Hold the Synergy Shape Back up to the desired height on the seat canes and make note of where the mounting brackets will be located. 3. Install the T-slot adapter as shown in figure 6. 4. Starting on one side, wrap the mounting band of the top bracket around the back cane so the mounting band is on the bottom. Fasten the mounting screw into the receiver. See figure 6. 5. Wrap the bottom mounting band marked for that side around the back cane so the mounting band is on the bottom. Fasten the mounting screw into the receiver. See figure 6. 6. Repeat for the other side. WARNING! Ensure the hardware is tight. www.quantumrehab.com T-SLOT ADAPTER RECEIVER MOUNTING BAND SEAT CANE MOUNTING SCREW TIGHTEN MOUNTING SCREW Figure 6. Mounting Bracket Installation on T-slotted Canes Synergy Shape Back
12 Installation and Care Instructions 7. Once the mounting brackets are in place, stand behind the chair and align the bottom mounting block on the seatback with the mounting pin on the bottom mounting bracket. Make sure to angle the seatback forward. See figure 7. Rotate the seatback backwards until it clicks into place. CLICK MOUNTING BLOCK MOUNTING PIN SEAT CANE Figure 7. Installing the Synergy Shape Back COMFORT ADJUSTMENTS Once you are familiar with the operation of your chair, there are adjustments you can make to your Synergy Shape Back to increase your comfort, like seatback depth, recline angle, width, and height. See figures 8, 9, 10, and 11. WARNING! If your Synergy Shape Back was configured by your Quantum Rehab Specialist, please consult your healthcare professional before changing the position of your Synergy Shape Back. WARNING! Never make adjustments while the chair is occupied. Synergy Shape Back www.quantumrehab.com
Installation and Care Instructions 13 Seatback Depth The seatback depth adjustment range is 4 in. (10.16 cm). To increase the seatback depth: 1. Ensure the mounting pins are located in the back of the mounting bracket. 2. Loosen the safety setscrew. See figure 3 or 4. 3. Loosen the positioning screws in both the top and bottom mounting brackets. 4. Slide the mounting pin out. See figure 8. 5. Retighten the positioning screws. 6. Retighten the safety setscrew. To decrease the seatback depth: 1. Ensure the mounting pins are located in the front of the mounting bracket. 2. Loosen the safety setscrew. See figure 3 or 4. 3. Loosen the positioning screws in both the top and bottom mounting brackets. 4. Slide the mounting pin in. See figure 8. 5. Retighten the positioning screws. 6. Retighten the safety setscrew. WARNING! When adjustments are complete, be sure to tighten all of the positioning screws and the safety setscrew if you moved the mounting pins. POSITIONING SCREW MOUNTING PIN POSITIONING SCREW MOUNTING PIN Figure 8. Seatback Depth Adjustment www.quantumrehab.com Synergy Shape Back
14 Installation and Care Instructions Recline Angle The recline angle can be adjusted from -33 to 57 . To increase the recline angle: 1. Loosen the safety setscrew. See figure 3 or 4. 2. Loosen the positioning screws on the top mounting brackets. 3. Move the mounting pins out. 4. If necessary, loosen the positioning screws on the bottom mounting brackets and move the mounting pins in. See figure 9. It may be necessary to move the mounting pins to the front location. See figure 4. 5. Retighten the positioning screws. 6. Retighten the safety setscrew. To increase the precline angle: 1. Loosen the safety setscrew. See figure 3 or 4. 2. Loosen the positioning screws on the top mounting brackets. 3. Move the mounting pins in. 4. If necessary, loosen the positioning screws on the bottom mounting brackets and move the mounting pins out. It may be necessary to move the mounting pins to the back location. See figure 3. 5. Retighten the positioning screws. 6. Retighten the safety setscrew. WARNING! When adjustments are complete, be sure to tighten all of the positioning screws and the safety setscrew if you moved the mounting pins to the front or rear position. POSITIONING SCREW -33 57 MOUNTING PIN POSITIONING SCREW MAXIMUM RECLINE MOUNTING PIN MAXIMUM PRECLINE Figure 9. Maximum Recline and Precline Angle Adjustment Synergy Shape Back www.quantumrehab.com
Installation and Care Instructions 15 Seatback Width The seatback width adjustment range is 2 in. (5.08 cm) to accommodate different chair widths. To adjust for different chair widths: 1. Loosen the positioning screws in the lateral supports. 2. Slide the mounting blocks closer to the edge of the seatback for wider chairs and closer to the middle of the seatback for narrower chairs. See figure 10. WARNING! When adjustments are complete, be sure to tighten all of the positioning screws LOOSEN POSITIONING SCREWS MOUNTING BLOCKS LOOSEN POSITIONING SCREWS Figure 10. Lateral Support Adjustment www.quantumrehab.com Synergy Shape Back
16 Installation and Care Instructions Seatback Height The seatback height adjustment range depends on the length of your seat canes. To raise the seatback height: 1. Loosen all four mounting screws. 2. Reposition all four mounting brackets higher on the seat canes. See figure 11. 3. Tighten all four mounting screws. To lower the seatback height: 1. Loosen all four mounting screws. 2. Reposition all four mounting brackets lower on the seat canes. See figure 11. 3. Tighten all four mounting screws. WARNING! When adjustments are complete, be sure to tighten all of the mounting screws. MOUNTING SCREW MOUNTING SCREW Figure 11. Seatback Height Adjustment Synergy Shape Back www.quantumrehab.com
Installation and Care Instructions 17 REMOVING THE SYNERGY SHAPE BACK Your Synergy Shape Back can easily be removed using the quick-release system. To remove the Synergy Shape Back: 1. Set the park brake or turn the controller off, if equipped. 2. Lift the quick-release handle on the back of the seatback and push the seat forward and up with one sweeping motion. See figure 12. WARNING! Do not attempt to remove the Synergy Shape Back when the chair is occupied. QUICK-RELEASE HANDLE SEAT CANE Figure 12. Removing the Synergy Shape Back www.quantumrehab.com Synergy Shape Back
18 Installation and Care Instructions CLEANING The Synergy Shape Back can be easily cleaned. To clean the Synergy Shape Back: 1. Locate the zipper on the back side of the outer cover. See figure 13. 2. Unzip the cover and pull out the inner cushion. 3. Wash the outer cover in a washing machine on the COLD setting. WARNING! Do not use bleach when washing the cover. WARNING! Never submerge the inner cushion of your Synergy Shape Back in water. The inner cushion is protected by a fluid-resistant cover, but it is not intended for direct exposure to water. 4. Allow the outer cover to air dry. WARNING! Do not attempt to put the outer cover in a dryer. This may cause shrinking. 5. Once dry, put the inner cushion back inside the cover. Zip the cover closed, and replace the Synergy Shape Back onto the seat of your chair. INNER CUSHION ZIPPER OUTER COVER Figure 13. Synergy Shape Back Cover Removal Synergy Shape Back www.quantumrehab.com
Installation and Care Instructions 19 STORAGE The Synergy Shape Back should not be stored in extremely hot or cold temperatures. WARNING! Extreme temperatures can affect the temperature of your seating system components and may cause skin irritation. Use caution when your power chair has been used or stored in an extremely hot or cold environment. CARE AND MAINTENANCE Refer to your power chair owner’s manual for proper disposal instructions. Be aware of safety issues while smoking. WARNING! Pride strongly recommends that you do not smoke cigarettes while seated in your seating system although the seating system has passed the necessar y testing requirements for cigarette smoking. You must adhere to the following safety guidelines if you decide to smoke cigarettes while seated in your seating system ! Do not leave lit cigarettes unattended. ! Keep ashtrays a safe distance from the seating system. ! Always make sure cigarettes are completely extinguished before disposal. All hardware on the Synergy Shape Back should be checked monthly to ensure that it is tight. WARNING! Tighten any hardware immediately to prevent personal injury or property damage. WARRANTY The Synergy Shape Back cushion is designed and produced to the highest of standards. Our Synergy Shape Back cushion is guaranteed to be free of defects in material and workmanship for a period of 24 months. The outer cover is guaranteed to be free of defects in material and workmanship for a period of 90 days. If any defect in material or workmanship is found, Pride Mobility Products will repair or replace, at our discretion, the Synergy Shape Back cushion. This warranty does not apply to cushions abused or misused by the user and deemed such by Pride Mobility Products. Claims and repairs should be processed through the nearest Quantum Rehab Specialist. www.quantumrehab.com Synergy Shape Back
www.pridemobility.com www.prideservice.com www.quantumrehab.com Pride Mobility Products Corporation 182 Susquehanna Avenue Exeter, PA 18643-2694 USA Pride Mobility Products Company 380 Vansickle Road Unit 350 St. Catharines, Ontario L2R 6P7 Canada Pride Mobility Products Ltd. Unit 106, Heyford Park Camp Road Upper Heyford, Oxfordshire OX25 5HA Pride Mobility Products Australia Pty. Ltd. 21 Healey Road Dandenong, 3175 Victoria, Australia Pride Mobility Products Italia S.r.l. Via del Progresso - ang. Via del Lavoro Loc. Prato della Corte 00065-Fiano Romano (RM) Pride Mobility Products Europe B.V. Tijnmuiden 28 1046 AL Amsterdam The Netherlands www.pridemobility.com www.prideservice.com *INFMANU2873* www.quantumrehab.com
The Synergy Shape Back is a unique seatback cushion that is available in standard, tall, and low versions and is fully adjustable for user comfort and positioning needs. Figures 1 and 2 provide information on the Synergy Shape Back components and cushions. Use this diagram to familiarize yourself with the function and location of
Therma Tru S296 ( ) Therma Tru S607 (Std NC Front Door) Therma Tru S255 ( ) Therma Tru S206 ( ) Exterior Doors Cont. 15 Therma Tru S262 ( ) Std Rear Door NC Therma Tru S118 ( ) Therma Tru S108 ( ) Therma Tru S161 ( ) Therma Tru S6082 ( ) Exterior Door Side Lites 16 S293 Sideli
Figures 1, 2, 3, and 4 provide informat ion on the TRU-Balance 2 Power Tilt, TRU-Balance 2 Power Recline, TRU-Balance 2 Power Tilt and Recline, and TRU-Balance 2 Lift a nd Tilt components. Use th ese diagrams to famil-iarize yourself with the function and location of each component before using the TRU-Balance 2 Power Positioning System.
May 05, 2018 · 10 Standard Arc S -3 11 Standard Arc S -6 12 Satin Glide Stainless 13 Tru -Core FC 70T 14 Tru -Core FC 71T 15 Tru -Core FC 71T -12C 16 Tru -Core FC 71T -12M 17 Tru -Core FC 71T -AG 18 Tru -Core FC 71T -CG 19 Tru -Core FC 81T -Ni1 20 Tru
This User Manual is a guide for use during the installation, normal operation and maintenance of a Synergy System or Synergy UV Water Purification System. 'Synergy' is used in this manual to refer to either the Synergy or the Synergy UV System unless otherwise noted. It is highly recommended to completely read this manual and to
The Harvey/Therma-Tru Partnership Certified distributor Harvey Building Products is a Certified Distributor of Therma-Tru products. We use only Therma-Tru and Therma-Tru-specified components to build door systems. All door units are set up to Therma-Tru specifications so you will receive what you’ve come to expect from Harvey—
synergy and evolution. Our synergy and evolution elevators combine state-of-the-art technology with flexible design. Immerse yourself in the design world of these two elevator families and choose the design that suits your taste and requirements. 4 synergy and evolution. With its compact dimensions, the synergy series is perfect for
three new synergy measures: the expected total cost synergy, the relative risk reduction synergy, and the absolute risk reduction synergy for the assessment of the potential strategic advantages. We illustrate the analytical framework with two sets of numerical examples
Automotive Hose and Fittings CONTENT 6 6.1 6.2 6.3 Hose and Fittings 634 G-Line Hose and Fittings 634 Quick Release Couplings 645 600 - 700 Series Hose and Fittings 648 200 Series Hose and Fittings 673 Push Fit Hose and Fittings 679 Adaptors 683 Air Conditioning Hose and 695 Fittings . 634 www.pirtek.com 6. 1 Series Page Hose 910 910 636 Hose 811 811 636 Hose 910 FC 910 FC 636 (Fuel Cell) G .
