Walterscheid Australia Ph: 1300 WALTER
Agricultural Product Catalogue Walterscheid Australia Ph: 1300 WALTER www.walterscheid.com.au
DISCLAIMER Disclaimer The information and dimensions listed in these catalogues is correct to the best of our knowledge and belief, having been compiled from reliable and official sources of information. However Walterscheid Australia (HS Company Pty Ltd) accepts no responsibility for possible errors, omissions or unsuitable parts being listed or fitted to any vehicle. Dimensions listed are nominal throughout. Due to our continuous product and range development we reserve the right to alter the specification without prior notice. We welcome any feedback re suspected errors or omissions to the information enclosed. We can be contacted via email walterscheid@walterscheid.com.au Or via Ph 03 9580 7300 or Fax 03 9580 0379 Alternatively via mail at PO Box 4262, Dandenong South, Vic. 3164. www.walterscheid.com.au Document No: SABRECAT 2 Issue: Issue Date: B:7-II 17/08/2020 This catalogue is the copyright of HS Company Pty Ltd
AGRICULTURAL CONTENTS DESCRIPTION: QUICK REFERENCE GUIDE.B:7-3 COMPARISON GUIDE.B:7-7 EUROPEAN PTO SHAFTS SINGLE JOINT ASSEMBLIES.B:7-8 COMPLETE SHAFTS.B:7-9 ‘T’ SERIES SHAFT PARTS.B:7-14 ‘V’ SERIES SHAFT PARTS.B:7-16 ‘E’ SERIES SHAFT PARTS.B:7-18 ‘AGC’ SERIES SHAFT PARTS.B:7-20 WIDE ANGLE ‘V’ SERIES SHAFT PARTS.B:7-22 QUICK RELEASE END YOKES.B:7-24 WIDE ANGLE QUICK RELEASE END YOKES.B:7-26 PINCH BOLT END YOKES.B:7-28 PLAIN BORE & KEY END YOKES.B:7-34 TUBE YOKES.B:7-36 WIDE ANGLE TUBE YOKES.B:7-40 DRIVE TUBE.B:7-42 FRICTION CLUTCH LININGS.B:7-46 CLUTCH - FM DISC TYPE.B:7-47 CLUTCH - DISC TYPE.B:7-48 SHEAR BOLT TORQUE LIMITER.B:7-50 OVERLOAD RATCHET CLUTCH.B:7-52 OVERRUNNING CLUTCH.B:7-53 COVER SETS.B:7-54 NORTH AMERICAN PTO SHAFTS NORTH AMERICAN SERIES SHAFT PARTS.B:7-56 NORTH AMERICAN COVER SETS.B:7-58 NORTH AMERICAN SHAFT OPTIONS.B:7-59 QUICK RELEASE END YOKES.B:7-60 PINCH BOLT END YOKES.B:7-61 PLAIN BORE & KEY END YOKES.B:7-62 NORTH AMERICAN SHEAR CLUTCH.B:7-64 NORTH AMERICAN OVERRUNNING CLUTCH.B:7-65 WIDE ANGLE SHAFT PARTS.B:7-66 www.walterscheid.com.au Document No: SABRECAT 2 Issue: Issue Date: GEARBOXES SLASHER.B:7-71 RIGHT ANGLE.B:7-72 MULTIPLIERS.B:7-73 SLASHER KITS (GEARBOX, PTO & CLUTCH).B:7-73 17/08/2020 This catalogue is the copyright of HS Company Pty Ltd # INDENT ITEM ONLY B:7-1
CONTENTS LINKAGE TOP LINK.B:7-74 RATCHET ARM.B:7-74 LINKAGE PINS.B:7-74 DRAWBAR HITCH PIN.B:7-76 CONVERSION BUSHES.B:7-76 DRAWBARS.B:7-76 SAFETY LOCKING PINS AND ACCESSORIES.B:7-77 WELD ON BALLS.B:7-78 A FRAME QUICK HITCH.B:7-79 FRONT LINKAGE FRONT LINKAGE SYSTEMS.B:7-80 FRONT LINKAGE APPLICATIONS CASE-IH / STEYR.B:7-81 CLAAS.B:7-83 JOHN DEERE.B:7-84 KUBOTA.B:7-85 MASSEY FERGUSON.B:7-86 NEW HOLLAND.B:7-88 RENAULT.B:7-89 VALTRA.B:7-90 ZETOR.B:7-91 BALER EMERGENCY RELEASE SYSTEM.B:7-92 HYDRAULIC CYLINDERS.B:7-93 www.walterscheid.com.au Document No: SABRECAT 2 Issue: # INDENT ITEM ONLY B:7-2 Issue Date: 17/08/2020 This catalogue is the copyright of HS Company Pty Ltd
Issue Date: Issue: Document No: 17/08/2020 46.80 60.30 46.04 25.40 25.40 26.99 70.00 36.80 24.60 27.00 38.10 36.80 23.80 24.60 62.00 23.80 38.10 55.00 22.00 23.80 54.00 22.00 37.70 47.00 18.00 B2 23.80 B1 C 2 SABRECAT www.walterscheid.com.au This catalogue is the copyright of HS Company Pty Ltd B:7-3 77.00 60.00 60.00 70.00 63.00 62.00 56.00 A Approx. (K5-A590) 4B32070 (RUJ-1788) 4122000 (114.2101) ASS-223 (RUJ-1798) ASS-222 4062000-1X (114-1004) 4062000 RUJ-0601 (5-170X) 4702000 RUJ-0600 (K5-A64) 4222000 (K5-A589) 4212000 (K5-A588) 4B12054 (K5-A587) 19.00.00 U/Joint Part No. B1 C Comments COMER 30 WALTERSCHEID W1 BYPY SERIES 3 WEASLER 12 ROCKWELL 12N NEAPCO 1200 JAYBEN 3AG JAYBEN 2AG Grease Nipple in Cap WEASLER 6 JAYBEN 1AG NEAPCO L600 ROCKWELL L6N NEAPCO 0600 TO ROCKWELL L6N/JAYBEN 1AG NEAPCO N1000, SPICER 1000 NEAPCO 0600 COMER 20 HARDY SPICER 1140 WALTERSCHEID W200/W2200 BYPY SERIES 2 WALTERSCHEID W100/W2100 COMER 10 BYPY SERIES 1 T30-023-001 12-102-1206 3YB9-1375/6 2YB9-1375/6 06-100-0606 T20-022-001 T10-021-001 1 3/8 x 6 12-102-1221 3YB9-1375/21 2YB9-1375/21 06-100-0621# T20-022-002 T10-021-002 1 3/8 x 21 1 3/4 x 6 1 3/4 x 20 SPLINED QUICK RELEASE YOKES QUICK REFERENCE GUIDE C B2 WALTERSCHEID W2000 B1 A T20-012-002 V20-012-320# T10-011-002 INNER # INDENT ITEM ONLY T20-012-003 V20-012-319# T10-011-003 OUTER TUBE YOKES
Issue Date: Issue: Document No: 17/08/2020 74.60 81.76 91.20 85.80 66.67 107.95 81.76 80.00 92.03 101.40 95.35 106.30 27.00 27.00 27.00 28.58 31.75 28.58 30.20 30.20 30.20 30.20 28.58 B1 C 2 SABRECAT www.walterscheid.com.au 65.88 B2 This catalogue is the copyright of HS Company Pty Ltd B:7-4 120.00 101.00 95.00 91.00 73.00 88.00 84.00 A Approx. (K5-A536) 23.00.00 K5-A735 (5-178-4X) 4622000-1X 4622000-4X (K5-A18R) 4622000 4B52079-1X (K5-A591) 4B52079 (114-3105) ASS-225 (K5-A798) 4352800 (CPL14N-1X) 4142000-1X (CPL14N) 4142000 K5-A734 5-433-1X K5-A13XR (K5-LGB36R) 4232000 U/Joint Part No. B1 C Comments COMER 70 HARDY SPICER 1410 WALTERSCHEID W230 BYPY SERIES 7 COMER 60 WIDE ANGLE COMER 60 HARDY SPICER 1350 WALTERSCHEID W220 BYPY SERIES 6 Grease Nipple in Cap 4 x Grease Nipple in Cap HARDY SPICER 3R JAYBEN 5AG COMER 50 BYPY SERIES 5 Grease Nipple in Cap WEASLER 35 SERIES WIDE ANGLE WEASLER 14 ROCKWELL 14N NEAPCO 2000 Grease Nipple in Cap COMER 40 WIDE ANGLE Grease Nipple in Cap T70-027-001 T60-026-230 T60-026-001 T50-025-001 35-113-3506# Collar Type 5YB9-1375/6 14-100-1406 Collar Type T40-024-261# 2-4-A3641 T40-024-001 1 3/8 x 6 T60-026-504 Collar Type T70-027-002 T60-026-002 T50-025-002# 35-113-3521# Collar Type 5YB9-1375/21 14-100-1421 Collar Type T40-024-272# 2-4-A4221 T40-024-002 1 3/8 x 21 T60-026-003 1 3/4 x 6 T60-026-505 Collar Type T70-027-004 T60-026-008 35-113-3520# Collar Type 5YB9-1750/20 1 3/4 x 20 SPLINED QUICK RELEASE YOKES QUICK REFERENCE GUIDE C B2 COMER 40 HARDY SPICER 1300 WALTERSCHEID W210/W2300 BYPY SERIES 4 JAYBEN 4AG HARDY SPICER 1310 B1 A V60-026-391 T60-026-249 T70-017-006 T60-016-029 V60-016-389 T50-015-012 V40-024-434# T40-024-269# T40-014-007 V40-014-428 INNER # INDENT ITEM ONLY V60-026-390 T60-026-229 T70-017-007 T60-016-028 V60-016-388 T50-015-011 V40-024-433# T40-024-263# T40-014-006 V40-014-427 OUTER TUBE YOKES
Issue Date: Issue: Document No: 17/08/2020 106.30 113.80 35.00 118.00 90.00 116.00 86.00 90.00 A Approx. K5-A765 (K5-A730W-4X) 4B82006-1X 4B82006-4X (K5-A730W) 4B82006HD (K5-A538) 4B82006 (RUJ-3004) 12.00.00 (114-5109) ASS-228 (K5-A800) 4552800 (RUJ-3009) 4442000 AGC35.06.00 (K5-A592) 4242000 (K5-A799) 4442800 (CP35N-4) 4352000-1X (CP35N-3) 4352000 U/Joint Part No. B1 C WEASLER 55 SERIES WIDE ANGLE WEASLER 44 ROCKWELL 44R SERIES WALTERSCHEID W2480 WALTERSCHEID W2400 WEASLER 44 SERIES WIDE ANGLE COMER 80 WIDE ANGLE Grease Nipple in Cap 4 x Grease Nipple in Cap COMER 80 HEAVY DUTY COMER 80 HARDY SPICER 1480 WALTERSCHEID W240 BYPY SERIES 8 WALTERSCHEID W11 JAYBEN 8AG A T80-028-358 Collar Type T80-028-001 8YB9-1375/6 55-111-5506 Collar Type 44-101-4406 Collar Type AGC35.10.10 AGC35.10.00 44-111-3506# Collar Type 35-101-3506 Collar Type 1 3/8 x 6 T80-028-359 Collar Type T80-028-002 8YB9-1375/21 55-111-5521# Collar Type 44-101-4421 Collar Type AGC35.10.12 AGC35.10.02 44-111-3521# Collar Type 35-101-3521 Collar Type 1 3/8 x 21 T80-028-361# Collar Type T80-028-003 35-102-3528# 1 3/4 x 6 T80-028-360 Collar Type T80-028-004 8YB9-1750/20 55-111-5520 Collar Type 44-101-4420 Collar Type 44-111-3520# Collar Type 35-101-3520 Collar Type 1 3/4 x 20 SPLINED QUICK RELEASE YOKES QUICK REFERENCE GUIDE C B2 Comments Grease Nipple in Cap WEASLER 35 NEAPCO 2200 ROCKWELL 35R B1 Many other parts not listed above are available on request. 106.30 56.00 34.00 35.00 84.15 33.35 79.77 76.00 94.00 32.00 27.00 94.46 76.00 32.00 33.33 38.89 81.76 109.54 31.75 31.75 70.84 81.36 31.75 B2 33.35 B1 C 2 SABRECAT www.walterscheid.com.au This catalogue is the copyright of HS Company Pty Ltd B:7-5 V80-028-249 T80-028-165 T80-018-134 V80-018-242 INNER # INDENT ITEM ONLY V80-028-248 T80-028-152 T80-018-133 V80-018-241 OUTER TUBE YOKES
Issue Date: Issue: Document No: 17/08/2020 94.00 89.00 89.00 106.00 109.60 115.90 108.00 118.00 104.00 107.50 126.21 135.00 118.00 140.00 125.00 35.00 36.00 36.00 32.00 38.89 39.70 41.00 41.00 42.00 42.00 45.24 49.00 50.00 50.00 52.00 B2 140.00 120.00 120.00 135.00 125.00 100.00 105.00 A Approx. K5-A780 4120K0001 (K5-A752) 27.00.03 (K5-A704) 4B01220-4X 4772000 4B0SH20-4X (K5-A595) 4262000 (K5-A594) 41210 (K5-A665) 41209 (K5-A725) 25.00.00 (CP55N) 4552000 AGC36.06.00 (K5-A593) 4252000 (K5-A693) 4B72094 U/Joint Part No. B1 C Comments WALTERSCHEID W2580 COMER 120 BYPY SERIES SK 2 x Grease Nipple in Cap WALTERSCHEID W2700 BYPY SERIES 12 (4 X LUBE IN CAP) WEASLER 77 SERIES COMER SERIES VP9 BYPY SERIES SH (4 x LUBE IN CAP) WALTERSCHEID W2600 BYPY SERIES 10 COMER 90 BYPY SERIES 9 WALTERSCHEID W250 WEASLER 55 ROCKWELL 55N NEAPCO N55 A 5720N0355 Collar Type AGC26.10.00 572100351# Collar Type T90-029-319 Collar Type 55-101-5506 Collar Type AGC36.10.10 AGC36.10.00 T7N-027-001 1 3/8 x 6 5720N3755 Collar Type AGC26.10.02 572103751# Collar Type T90-029-320 Collar Type 55-101-5521 Collar Type AGC36.10.12 AGC36.10.02 T7N-027-002 1 3/8 x 21 D120-220-005# 5720N0455 Collar Type 572100451 Collar Type T90-029-317# Collar Type 55-101-5528# Collar Type 1 3/4 x 6 D120-220-001 507203852 5720N3855 Collar Type AGC26.18.02 572103851 Collar Type T90-029-318 Collar Type 55-101-5520 Collar Type AGC36.18.12 AGC36.18.02 1 3/4 x 20 SPLINED QUICK RELEASE YOKES QUICK REFERENCE GUIDE C B2 WALTERSCHEID W2500 BYPY SERIES N7 B1 Many other parts not listed above are available on request. B1 C 2 SABRECAT www.walterscheid.com.au This catalogue is the copyright of HS Company Pty Ltd B:7-6 AGC26.13.00 204106852 T90-019-128 V90-019-167 AGC36.13.100 T7N-017-011 INNER # INDENT ITEM ONLY AGC26.14.00 204106851 T90-019-127 V90-019-166 AGC36.14.100 T7N-017-012 OUTER TUBE YOKES
Issue Date: Issue: Document No: NOTE: Sabre AGC2400 AGC2500 AGC2600 Sabre T10 T20 T40 T60 T80 T90 Bareco W2400 W2500 W2600 Heavy Duty Range Comer Bypy Walterscheid V60 406 P400 V80 408 P500 V90 409 P600 Sabre AGC2480 AGC2580 Sabre 1. These comparisons are for ratings only. Parts are not interchangeable between all sizes. Bareco 1 2 4 6 8 9 WB6 Bareco WB4 WB6 Bareco # INDENT ITEM ONLY Wide Angle Shafts (2 x CVJ) Comer Bypy Walterscheid T20 or V20-2CV 672 WWZ2280 T40 or V40-2CV 674 WWZ2380 T60 or V60-2CV 676 WWZ2480 T80 or V80-2CV 678 WWZ2580 Wide Angle Range Wide Angle Shafts (1 x CVJ) Comer Bypy Walterscheid T20 or V20-CV 652 or 662 WWE2280 T40 or V40-CV 654 or 664 WWE2380 T60 or V60-CV 656 or 666 WWE2480 T80 or V80-CV 658 or 668 WWE2580 COMPETITOR COMPARISON GUIDE Standard Range Hardy Spicer Bypy Walterscheid 101 W2100 1140 102 W2200 1310 104 W2300 1350 106 W2400 1480 108 W2500 109 W2600 17/08/2020 2 SABRECAT www.walterscheid.com.au This catalogue is the copyright of HS Company Pty Ltd B:7-7
Issue Date: Issue: Document No: 17/08/2020 2 SABRECAT www.walterscheid.com.au 25.40 25.00 SKA-10100 SKA-10250M 0.984 1.000 0.875 0.750 22.23 25.40 25.00 1AGS-YM-YM-7/8 1AGS-YM-YM-3 1AGS-YM-YM-25 0.984 1.000 0.875 0.750 8.00 6.35 4.78 4.78 8.00 6.35 6.35 4.78 0.315 0.250 0.188 0.188 Key 41.28 41.28 41.28 41.28 1.625 1.625 1.625 1.625 Hub O.D. 127.00 127.00 127.00 127.00 5.000 5.000 5.000 5.000 Length L 27.00 27.00 27.00 27.00 1.063 1.063 1.063 1.063 Length Thru Hole 60 60 60 60 Angle 47.50 47.50 47.50 47.50 1.870 1.870 1.870 1.870 Hub O.D. 127.00 127.00 127.00 127.00 5.000 5.000 5.000 5.000 Length L 27.00 27.00 27.00 27.00 1.063 1.063 1.063 1.063 Length Thru Hole 60 60 60 60 Angle 1AGS SERIES SINGLE JOINT ASSEMBLY 0.315 0.250 0.250 0.188 Key 1000 SERIES SINGLE JOINT ASSEMBLY Note: More options and configurations in 1AGS series are available on request, contact your local branch for more information. 19.05 1AGS-YM-YM-3/4 Hole Dia A 22.23 SKA-10875 Part Number 19.05 Hole Dia A SKA-10750 Part Number This catalogue is the copyright of HS Company Pty Ltd B:7-8 # INDENT ITEM ONLY Comments Comments
Issue Date: Issue: Document No: 17/08/2020 @ 1000 RPM 25HP / 18kW 42hp / 31kW 60HP / 45kW 60HP / 45kW 100HP / 74kW 139HP / 103kW 16HP / 12kW 27HP / 20kW 38HP / 28kW 38HP / 28kW 64HP / 47kW 90HP / 67KW AG1 AG2 AG3 AG3H AG4 AG5 Horsepower Ratings @ 540 RPM Series 2 SABRECAT www.walterscheid.com.au This catalogue is the copyright of HS Company Pty Ltd B:7-9 1210mm 1610mm 1910mm 1410mm 1010mm 1510mm 1910mm 1410mm 1010mm 1510mm 1910mm 1410mm 1010mm 1510mm 1950mm 1450mm 1010mm 1510mm 1450mm 710mm 510mm 1010mm Extended mm Compressed mm Length C - C of U/Joints AG5-1210-SC2 AG4-1510-SC2 AG4-1010-SC2 AG3H-1510-SC2 AG3H-1010-SC2 AG3-1510-SC2 AG3-1010-SC2 AG2-1510-SC2 AG2-1010-SC2 AG1-1010-SC2 AG1-510-SC2 1 3/8 x 6 QR Both Ends (Collar Type) AG5-1210-SC1 AG4-1510-SC1 AG4-1010-SC1 AG3H-1510-SC1 AG3H-1010-SC1 AG3-1510-SC1 AG3-1010-SC1 AG2-1510-SC1 AG2-1010-SC1 AG1-1010-SC1 AG1-510-SC1 1 3/8 x 6 QR One End Only (Collar Type) No End Yokes COMPLETE SHAFTS AG SERIES COMPLETE SHAFTS # INDENT ITEM ONLY Uses Star Tube S4 / S5 Uses 1b/2a Tube Uses 1b/2a Tube Uses 0v/1 Tube Uses 0v/1 Tube Notes
Issue Date: Issue: Document No: 17/08/2020 @ 1000 RPM 25HP / 18kW 31hp / 23kW 55HP / 40kW 100HP / 74kW 150HP / 110kW 16HP / 12kW 21HP / 15kW 35HP / 26kW 64HP / 47kW 95HP / 70kW T10 T20 T40 T60 T80 Horsepower Ratings @ 540 RPM Series 2 SABRECAT www.walterscheid.com.au This catalogue is the copyright of HS Company Pty Ltd B:7-10 1910mm 1410mm 1010mm 1510mm 1910mm 1410mm 1010mm 1510mm 1910mm 1410mm 1010mm 1510mm 1950mm 1450mm 1010mm 1510mm 1450mm Extended mm 1010mm Compressed mm Length C - C of U/Joints T80-1510F112112 T80-1010F112112 T60-1510F112112 T60-1010F112112 T40-1510F112112 T40-1010F112112 T20-1510F112112 T20-1010F112112 T10-1010F112112 1 3/8 x 6 QR (Pin Type) Both Ends T80-1510F112000 T80-1010F112000 T60-1510F112000 T60-1010F112000 T40-1510F112000 T40-1010F112000 T20-1510F112000 T20-1010F112000 T10-1010F112000 1 3/8 x 6 QR (Pin Type) One End Only T80-1510F000000 T80-1010F000000 T60-1510F000000 T60-1010F000000 T40-1510F000000 T40-1010F000000 T20-1510F000000 T20-1010F000000 T10-1010F000000 No End Yokes COMPLETE SHAFTS ‘T’ SERIES COMPLETE SHAFTS # INDENT ITEM ONLY T80-1010F112100 1 3/8 x 6 QR Flange to suit Howard Friction Clutch
Issue Date: Issue: Document No: 17/08/2020 @ 1000 RPM 103HP / 77kW 151HP / 113kW 188HP / 140kW 67HP / 50kW 99HP / 74kW 118HP / 88kW V60 V80 V90 Horsepower Ratings @ 540 RPM Series 2 SABRECAT www.walterscheid.com.au This catalogue is the copyright of HS Company Pty Ltd B:7-11 2010mm 1480mm 1010mm 1510mm 2010mm 1510mm 1010mm 1510mm 1910mm 1410mm 1010mm 1510mm Extended mm Compressed mm Length C - C of U/Joints V901510ENC12C12# V901010ENC12C12 V801510ENC12C12 V801010ENC12C12 V601510ENC12C12 V601010ENC12C12 1 3/8 x 6 QR (Collar Type) Both Ends COMPLETE SHAFTS ‘V’ SERIES COMPLETE SHAFTS V801510ENCVC12 V801010ENCVC12# V601510ENCVC12 V601010ENCVC12 1 3/8 x 6 QR (Collar Type) Both Ends # INDENT ITEM ONLY WIDE ANGLE COMPLETE SHAFTS
Issue Date: Issue: Document No: 17/08/2020 1010mm Compressed mm 1650mm Extended mm Length C - C of U/Joints D121010ENC25000 1 3/4 x 20 QR On One End Only COMPLETE SHAFTS @ 540 RPM 117HP / 87kW 1917mm 179HP / 134kW @ 1000 RPM Horsepower Ratings 55-38-60222 1 Clutch Yoke Only 50 CV Clutch Yoke 1 3/8 x 21Spl Clamp Bolt 57112000 2 Clutch Pack Only Clutch Pack 55-14605589 1 3/8 x 21Spl CB 1 3/8 x 21Spl CB Complete Shaft Part Number 3 # INDENT ITEM ONLY Note: Other end yokes are available on request. 55-857-5521 3 End Yoke Only 50 CV Yoke 1 3/8 x 21Spl Clamp Bolt Complete Double 50 CV PTO Shaft with Friction Overrun Clutch Compressed mm Length C - C of U/Joints 1 300hp / 221kW 196HP / 144kW 2 @ 1000 RPM @ 540 RPM Horsepower Ratings ‘D’ SERIES COMPLETE SHAFTS Note: Clutch pack # 57112000 utilizes M10 mounting holes. The four flange holes on the CV clutch yoke are 5/16”. To accommodate clutch pack # 57112000, the flange holes need to be drilled out to suit 10mm bolts. 5550 Series D120 Series 2 SABRECAT www.walterscheid.com.au This catalogue is the copyright of HS Company Pty Ltd B:7-12
Issue Date: Issue: Document No: 47 82 90 48 67 64 110 120 64 90 AGC2400 AGC2500 AGC2600 AGC2480 AGC2580 139 99 166 150 100 HP 104 74 124 112 74 kW 1850mm 1550mm 1210mm 1510mm 1575mm 1210mm 1780mm 1380mm 1010mm 1410mm 1910mm 1410mm 1010mm 1510mm 1910mm 1410mm 1010mm 1510mm Extended mm Compressed mm AGC2600-SS-141 AGC2600-SS-101 AGC2500-SS-151 AGC2500-SS-101 AGC2400-SS-151 AGC2400-SS-101 No Yokes Fitted COMPLETE SHAFTS ‘AGC’ SERIES COMPLETE SHAFTS Length C - C of U/Joints A selection of AGC Series Yokes and Clutches are available in the relevant sections of the Walterscheid DLS and Sabre AG catalogues. kW @ 1000 RPM Horsepower Ratings HP Series @ 540 RPM 17/08/2020 2 SABRECAT www.walterscheid.com.au This catalogue is the copyright of HS Company Pty Ltd B:7-13 Triangular tubing # INDENT ITEM ONLY Note: Other end yokes are available on request. AGC2580-SS-151 AGC2580-SS-121 AGC2480-TT-121 1 3/8 x 6 QR Both Ends 80 WIDE ANGLE COMPLETE SHAFTS
‘T’ SERIES OUTER SHAFT PARTS 2 1 3 5 Shaft Identification Series 1 2 4 5 6 7 7N 8 9 10 U/Joint Nominal Size Yoke Width 22.00 Universal Joint Outer Tube Yoke Outer Tube Outer Roll Pin 1 2 3 4 5 T10-021-001 4B12054 T10-011-003 191-110-200 190-000-011 50 x 8 T20-012-003 191-120-200 190-000-012# 55 x 8 T40-014-006 191-130-200 191-000-014 65 x 8 T50-015-011 191-150-200 190-000-016 70 x 10 T60-016-028 191-160-200 190-000-018 80 x 10 T70-017-007 191-160-200 190-000-018 80 x 10 62.00 (K5-A588) 54.00 23.80 68.00 T20-022-001 61.30 26.99 83.00 T40-024-001 95.00 T50-025-001 106.00 T60-026-001 119.00 T70-027-001 23.00.00 (K5-A536) 106.30 35.00 4622000 (K5-A18R) 92.08 30.20 4B52079 (K5-A591) 80.00 30.20 4232000 (K5-LGB36R) 74.61 30.20 4222000 (K5-A64) 109.00 T7N-027-001 4B72094 T7N-017-012 191-160-200 190-000-018 T80-028-001 4B82006 T80-018-133 191-198-850 190-000-243 90 x 12 T90-019-127 191-198-850 190-000-243 90 x 12 94.00 34.93 119.00 (K5-A538) 106.30 41.00 122.00 108.00 41.00 T90-029-319 41209 Collar Type (K5-A665) 131.00 118.00 # INDENT ITEM ONLY B:7-14 QR Yoke 1 3/8 x 6 European PTO 4 www.walterscheid.com.au 572100351 41210 Collar Type (K5-A594) 204106851# Document No: SABRECAT 2 Issue: Issue Date: 17/08/2020 This catalogue is the copyright of HS Company Pty Ltd
‘T’ SERIES INNER SHAFT PARTS 7 6 8 2 European PTO 1 Shaft Identification Series 1 2 4 5 6 7 7N 8 9 www.walterscheid.com.au Document No: SABRECAT 2 Issue: Issue Date: 17/08/2020 This catalogue is the copyright of HS Company Pty Ltd 10 U/Joint Nominal Size Yoke Width 22.00 Inner Roll Pin Inner Tube Inner Tube Yoke 6 7 8 Complete Shaft 1 3/8x6 QR both Ends 62.00 T10-1010F112112 190-000-010# 191-110-100 T10-011-002 45 x 8 54.00 23.80 1010mm C-C 68.00 T20-1010F112112 190-000-011 191-120-100 T20-012-002 50 x 8 61.30 26.99 1010mm C-C 83.00 T40-1010F112112 T40-1510F112112 190-000-012 191-140-100 T40-014-007 55 x 8 74.61 30.20 1510mm C-C - - 95.00 190-000-394# 191-150-100 T50-015-012 65 x 10 80.00 30.20 1010mm C-C 106.00 T60-1010F112112 T60-1510F112112 190-000-016 191-150-100 T60-016-029 70 x 10 92.08 30.20 1510mm C-C - - 119.00 190-000-016 191-170-100 T70-017-006 70 x 10 106.30 35.00 1010mm C-C 109.00 T7N-1010F112112 190-000-016 191-170-100 T7N-017-011 70 x 10 94.00 34.93 1010mm C-C 119.00 T80-1010F112112 T80-1510F112112 190-000-271 191-190-300 T80-018-134 80 x 10 106.30 41.00 1510mm C-C - - - - 122.00 190-000-243 191-190-300 T90-019-128 90 x 12 108.00 41.00 1010mm C-C 131.00 - - 204106852 118.00 # INDENT ITEM ONLY B:7-15
‘V’ SERIES OUTER SHAFT PARTS 2 1 3 5 Shaft Identification Series 1 2 4 5 6 7 8 9 U/Joint Nominal Size Yoke Width 22.00 QR Yoke 1 3/8 x 6 Universal Joint Outer Tube Yoke Outer Tube Outer Roll Pin 1 2 3 4 5 T20-022-001 4222000 62.00 54.00 23.80 68.00 (K5-A64) 61.30 26.99 83.00 T40-024-001 191-140-800 190-000-014 65 x 8 4B52079 V50-015-361# 191-160-800 190-000-016 70 x 10 V60-016-388 191-160-800 190-000-018 80 x 10 V80-018-241 191-190-800 190-000-243 90 x 12 V90-019-166 191-190-800 190-000-243 90 x 12 (K5-A591) 80.00 106.00 T60-026-001 4622000 (K5-A18R) 92.08 30.20 V40-014-427 95.00 T50-025-001 30.20 4232000 (K5-LGB36R) 74.61 30.20 V20-012-319# 191-120-800# 190-000-012# 55 x 8 119.00 106.30 34.93 119.00 T80-028-001 4B82006 (K5-A538) 106.30 41.00 European PTO 4 122.00 108.00 T90-029-319 41209 Collar Type (K5-A665) www.walterscheid.com.au Document No: SABRECAT 2 Issue: # INDENT ITEM ONLY B:7-16 Issue Date: 17/08/2020 This catalogue is the copyright of HS Company Pty Ltd
‘V’ SERIES INNER SHAFT PARTS 7 6 8 2 European PTO 1 Shaft Identification Series 1 2 4 5 6 7 8 9 U/Joint Nominal Size Yoke Width 22.00 Inner Roll Pin Inner Tube Inner Tube Yoke 6 7 8 - - - Complete Shaft 1 3/8x6 QR both Ends Collar Type Yokes 62.00 54.00 23.80 68.00 190-000-011 191-120-700#V20-012-320# 50 x 8 61.30 26.99 83.00 V401010ENC12C12 V401510ENC12C12 190-000-012# 191-140-700 V40-014-428 55 x 8 74.61 30.20 1510mm C-C 95.00 190-000-394# 191-160-700 V50-015-362# 65 x 10 80.00 30.20 1010mm C-C 106.00 V601010ENC12C12 V601510ENC12C12 190-000-016 191-160-700 V60-016-389 70 x 10 92.08 30.20 1010mm C-C 1510mm C-C 119.00 - - - 106.30 34.93 119.00 V801010ENC12C12 V801510ENC12C12 190-000-271 191-190-700 V80-018-242 80 x 12 106.30 41.00 1010mm C-C 1510mm C-C 122.00 V901010ENC12C12# 108.00 190-000-243 191-190-700 V90-019-167 90 x 12 1010mm C-C www.walterscheid.com.au Document No: SABRECAT 2 Issue: Issue Date: 17/08/2020 This catalogue is the copyright of HS Company Pty Ltd # INDENT ITEM ONLY B:7-17
‘E’ SERIES OUTER SHAFT PARTS 1 2 3 Shaft Identification Series 4 6 8 9 U/Joint Nominal Size Yoke Width 26.99 QR Yoke 1 3/8 x 6 Universal Joint Weld-in Tube Yoke Outer Tube Splined Sleeve 1 2 3 4 5 4232000 E40-014-003# 50X4MM E40-014-249# E60-016-035# - E60-016-032# E80-018-144 60X5MM E80-018-014 83.00 T40-024-001 (K5-LGB36R) 74.61 30.20 106.00 T60-026-001 119.00 T80-028-001 4B82006 (K5-A538) 106.30 41.00 4622000 (K5-A18R) 92.08 34.93 5 122.00 108.00 T90-029-319 41209 Collar Type (K5-A665) E90-019-055 63.5X5.5MM E90-019-056 European PTO 4 www.walterscheid.com.au Document No: SABRECAT 2 Issue: # INDENT ITEM ONLY B:7-18 Issue Date: 17/08/2020 This catalogue is the copyright of HS Company Pty Ltd
‘E’ SERIES INNER SHAFT PARTS 7 6 8 2 European PTO 1 Shaft Identification Series 4 6 8 9 U/Joint Nominal Size Yoke Width 26.99 108.00 - - 190-000-016 E60-150-715# E60-016-031# 70 x 10 765mm - - 190-000-018 E80-170-688 80 x 10 735mm E80-018-145 - - 190-000-243 E90-190-617 730mm 90 x 12 E90-019-054 - - 8 119.00 106.30 41.00 190-000-012# E40-140-611# E40-014-250# 55 x 8 780mm 7 106.00 92.08 34.93 Complete Shaft 6 Inner Inner Splined Bar Tube Yoke 83.00 74.61 30.20 Complete Shaft Inner Roll Pin 122.00 www.walterscheid.com.au Document No: SABRECAT 2 Issue: Issue Date: 17/08/2020 This catalogue is the copyright of HS Company Pty Ltd # INDENT ITEM ONLY B:7-19
‘AGC’ SERIES OUTER SHAFT PARTS 2 1 3 5 Shaft Identification Series U/Joint Size Nominal Yoke Width 32.00 85.00 2400 QR Yoke 1 3/8 x 6 Universal Joint Outer Tube Yoke Outer Tube Outer Roll Pin 1 2 3 4 5 AGC35.10.00 76.00 36.00 AGC35.14.100 AGC75.45.00 61.05.08 AGC36.14.100 AGC75.45.00 61.05.12 AGC26.14.00 AGC75.46.00 61.06.08 100.00 2500 AGC36.10.00 4252000 (K5-A593) 89.00 42.00 4242000 (K5-A592) 117.00 2600 AGC26.10.00 104.00 4262000 (K5-A595) A selection of AGC Series Yokes and Clutches are available in the relevant sections of the Walterscheid DLS and Sabre AG catalogues. European PTO 4 www.walterscheid.com.au Document No: SABRECAT 2 Issue: # INDENT ITEM ONLY B:7-20 Issue Date: 17/08/2020 This catalogue is the copyright of HS Company Pty Ltd
‘AGC’ SERIES INNER SHAFT PARTS 7 6 8 2 European PTO 1 Shaft Identification Series U/Joint Size 32.00 Nominal Yoke Width Inner Roll Pin Inner Tube Inner Tube Yoke 7 8 Complete Shaft (No Yokes) Complete Shaft No Yokes 6 85.00 AGC2400-SS-101 AGC2400-SS-151 2400 61.05.08 AGC75.44.00 AGC35.13.100 1010mm 76.00 36.00 1510mm 100.00 AGC2500-SS-101 AGC2500-SS-151 2500 61.05.12 AGC75.44.00 AGC36.13.100 1010mm 89.00 42.00 1510mm 117.00 AGC2600-SS-101 AGC2600-SS-141 2600 61.06.08 AGC75.45.00 AGC26.13.00 104.00 1010mm 1410mm A selection of AGC Series Yokes and Clutches are available in the relevant sections of the Walterscheid DLS and Sabre AG catalogues. www.walterscheid.com.au Document No: SABRECAT 2 Issue: Issue Date: 17/08/2020 This catalogue is the copyright of HS Company Pty Ltd # INDENT ITEM ONLY B:7-21
WIDE ANGLE ‘V’ SERIES OUTER SHAFT PARTS 1 2 3 2 4 6 Shaft Identification 6 8 Universal Joint Coupling Yoke Outer Tube Outer Tube Yoke 1 2 3 T20-022-162# - T40-024-261 K5-A734 T40-024-259 V40-024-433 191-140-800 T60-026-230 K5-A735 T60-026-224 V60-026-390 191-160-850 T80-028-358 K5-A765 T80-028-157 V80-028-248 191-190-850 4 5 68.00 74.10 23.80 T20-022-160# V20-022-325# 191-120-800# 82.10 83.00 27.00 85.80 4 Nominal Yoke Width 91.20 106.00 30.20 95.35 2 U/Joint Size 101.40 119.00 34.93 106.30 Series QR Yoke 1 3/8 x 6 113.80 European PTO 5 www.walterscheid.com.au Document No: SABRECAT 2 Issue: # INDENT ITEM ONLY B:7-22 Issue Date: 17/08/2020 This catalogue is the copyright of HS Company Pty Ltd
WIDE ANGLE ‘V’ SERIES INNER SHAFT PARTS 8 7 9 2 3 2 European PTO 1 Shaft Id Series U/Joint Size 6 8 74.10 82.10 Rils
This catalogue is the copyright of HS Company Pty Ltd. Document No: Issue: Issue Date: SABEAT 2 17/08/2020. www.walterscheid.com.au. B:7-II. DISCLAIMER. Disclaimer . The information and dimensions listed in these catalogues is correct to the best of our . knowledge and belief, having been compiled from reliable and official sources of information.
WSDOT Design Manual M 22-01.15 Page 1300-1 July 2018 Chapter 1300 Intersection Control Type 1300.01 General. 1300.02 Intersection Control Objectives. 1300.03 Common Types of Intersection Control. 1300.04 Modal Considerations. 1300.05 Procedures. 1300.06 Do
Walter Cut tools 2 Tiger·tec Silver cutting tool material 12 Walter Cut geometries 16 20 Walter Cut inserts Designation key 20 Walter Select 23 SX inserts 26 . - Page A 246 in the 2012 Walter General catalogue 3. G1111 GX monoblock tool for axial grooving - Shank sizes 25 x 25 mm
Australia Post Travel Insurance, c/o Travel Insurance 1300 728 015 auspost-claims@travelinsurancepartners.com.au Australia Post Travel Insurance, c/o Travel Insurance 1300 728 015 Australia Post Travel Insurance, c/o Travel Insurance are cruising in Australia (e.g. on the Murray River) or in
Walter HSK40 // Shaft ø20 / Shaft ø32 mm // RS ø50 and ø60 mm Accessories Walter grinding wheel adapter HSK40 // Shaft ø20 and ø32 // RS ø50 and ø60 mm Accessories ø50 mm Accessories ø60 mm GWA HSK40 // ø20 / ø32 mm // RS ø50 / ø60 mm For Walter tool grinding machines wit
and simply to the correct cutting data. With Tools & More on their smartphone, users can make detailed calculations on cutting data and cost efficiency. . service.tr@walter-tools.com Walter Wuxi Co. Ltd. Wuxi, Jiangsu, P.R. China 86 (510) 8241 9399, service.cn@walter-tools.com Walter AG Singapore Pte. Ltd. 65 6773 6180, service.sg@walter .
Thursday: Chapter 13: Art of the Americas before 1300 The rise of civilizations in the Americas before 1300 Friday: Chapter 13: Art of the Americas before 1300 The rise of civilizations in the Americas before 1300 Response Paper II Due Week 5: Late Antiquity and Early Medieval Art Monday:
PRO-I 1300 PRO-I 1300 PRO-I 1300: max. Schweißstrom/-zeit: 3150 A/1500 mS max. Schweißdurchmesser 25 mm PRO-I 2200 PRO-I 1300: max. Schweißstrom/-zeit: 3150 A/1500 mS max. Schweißdurchmesser 25 mm » optional erhältlich für alle Geräte der Serie PRO-I » ermöglicht das Bolzenschweißen mit Schutzgas als Schweißbadschutz
APS 240 Interlude Ð Writing Scientific Reports Page 5 subspecies of an organism (e.g. Calopteryx splendens xanthostoma ) then the sub-species name (xanthostoma ) is formatted the same way as the species name. In the passage above you will notice that the name of the damselfly is followed by a name: ÔLinnaeusÕ. This is the authority, the name of the taxonomist responsible for naming the .
