LumaRail Free Stand Bed Assist Rail With IntelliBrite LED Night Light
LumaRail Free Stand Bed Assist Rail with IntelliBrite LED Night Light Assembly and Operation Instructions Thank you for investing in this premium Platinum Health product. Please carefully follow the assembly and use instructions outlined below. Preparation 1. Prepare a large unobstructed area to assemble the bed rail. Assembly is best performed on a large, sturdy, flat surface like a table or on the floor. 2. Unwrap all components and ensure that all pieces are accounted for. Ensure that there are a total of 4 metal tubing sections, one security strap and one IntelliBrite LED light. www.platinumhealthllc.com info@platinumhealthllc.com
Assembly 1. Insert one of the silver bars into the padded hand rail (bent tube with padding). Once inserted make sure the brass tab sets into place, securing the two pieces together. Repeat this process with other silver tube by inserting it into other side of the padded hand rail. 2. Insert the opposite end of the silver tube into the U-shaped white tubing. Repeat this process with the one on the opposite side. Make sure the brass tabs are locked into place. www.platinumhealthllc.com info@platinumhealthllc.com
3. The finished frame should look like the picture below. Mounting the bedrail to your bed 1. It is important to carefully follow the instructions outlined below to ensure a safe and secure installation. 2. Lift the mattress and slide the horizontal support bar under it while positioning the entire rail at the correct distance from the head of the bed to best suit your needs. 3. Lower the mattress and make any final adjustments to the positioning of the rail. 4. Anchor your bed rail to the frame of the bed by following the next steps. www.platinumhealthllc.com info@platinumhealthllc.com
Anchoring 1. To anchor the bed assist rail to the bed frame, use the attached anchor strap as shown. Attach the anchor strap to the bed frame on the OPPOSITE SIDE of the bed from where the vertical hand rail is installed. 2. Loop the anchor strap around center of the horizontal support bar closed end and in turn around the entire bed frame, forming one continuous loop. Tighten the loop so that the anchor strap is very tight with no play. 3. Test the hand rail section to ensure that it is not able to pull away from the bed. 4. Once secure, your bed assist rail is ready to use. Attaching and using the IntelliBrite LED Night Light. 1. Apply the double-sided tape to the back of the night light. 2. Attach the light to the Night Light mounting tab as shown here. 3. The night light may be mounted with the LED lens facing either up or down. Aiming the LED lens up will provide more overall light in the room while aiming the LED lens down will provide better floor lighting. Select the best mounting option for your environment. 4. Move the Night Light switch to the “sensor” position. 5. Your Night Light is now ready to use. This light features a built in light sensor and an infrared motion sensor. The light sensor recognizes ambient light and prevents the Night Light from turning on when there is sufficient light in the room. At night, when the room is dark, any movement in front of the light will turn the light on. You can activate the light by passing your hand in front of the sensor at anytime. The light will also automatically turn on as soon as it senses you exiting the bed. The light will stay on for approximately 20 seconds. www.platinumhealthllc.com info@platinumhealthllc.com
NIGHT LIGHT BATTERY REPLACEMENT The batteries in your IntelliBrite LED Night Light will eventually require replacement. As shown in the image here, battery replacement is quick and simple to perform. 1. With the thin, flat mounting plate on the underside of the night light held secure, slide the entire night light in the direction toward the word "unlock" found on the side of night light. The night light will easily slide approximately 1/4" and the light can then be lifted away from the mounting plate. 2. Open the two battery compartments using a small flat screwdriver by rotating the cap in the direction of the "open" arrow and remove the black plastic caps. 3. Remove the old batteries and replace them with new batteries. (Use lithium batteries model number CR2032). Make sure the positive or " " side of the battery faces up. 4. Replace the black plastic covers and secure them by rotating in the direction of the "close" arrow. 5. Place the night light back onto the mounting plate and slide the entire night light toward the word "lock" to secure the night light to the mounting plate. www.platinumhealthllc.com info@platinumhealthllc.com
4. Once secure, your bed assist rail is ready to use. Attaching and using the IntelliBrite LED Night Light. 1. Apply the double-sided tape to the back of the night light. 2. Attach the light to the Night Light mounting tab as shown here. 3. The night light may be mounted with the LED lens facing either up or down.
12 51-87 Kits for Ford Flareside 14 48-85 Kits for Dodge Stepside 15 Bed Parts Installation BED FLOOR 16 Bed Wood O ak/Pine 19 Specialty Bed Wood 21 Exotic Bed W ood 22 Standard Bed Strips 25 Angle Strips 28 Bed Bolt Kits 31 "No Bolts" Bed Parts 36 Aluminum Bump and Flat Bed Strips BED PARTS 42 Front Bed Panels 44 Cross Sills/Reinforcement Strips
Flat 1 Ground 4-bed 197 2,120 Flat 2 Ground 3-bed 161 1,733 Flat 3 1st 1-bed 45 484 Flat 4 1st 1-bed 50 538 Flat 5 1st 1-bed 56 603 Flat 6 1st 1-bed 50 538 Flat 7 2nd 1-bed 51 549 Flat 8 2nd 1 bed 50 538 Flat 9 2nd 1-bed 56 603 Flat 10 2nd 1-bed 50 538 Total 766 8,245 Scheme ref: P2017/2080/PRA Net Saleable Areas: UNIT FLOOR BEDS NSA SQ. M. NSA .
The time-tested Murphy bed mechanism with attractive hide-away bi-fold pocket doors that collapse into the bed cabinet sides. Presidential indeed, with ample storage for books or collectibles. The bookcase doors effortlessly glide open on sturdy tracks. style murphy bed murphy bed murphy bed
chest of drawers twin bed option b queen bed option a ohc night stand wardrobe tv twin bed 32 x 80 twin bed 32 x 80 34sbd wardrobe night stand ward-robe private toilet shower refer. sofa entry chair ohc ohc ohc wardrobe ohc pantry micro-wave tv ohc ohc ohc ohc opt. tv sky light ohc queen bed 60 x 74 booth dinette free standing .
Once in bed, does your child have difficulty staying in bed or remaining still in bed when instructed to do so? . TV or music turned off after a few hours) (D) Bed What type of bed does the child sleep in (e.g., bunk bed, bed with rails etc ) What is the mattress quality? (e.g., could it cause discomfort?) (E) Other Is there anything else .
1.800.975.8451 Shevlin Murphy Bed PART A: Assembling Wall Bed Step 1: Remove Wall Bed from packaging (package includes 6 bed pieces). Retrieve 2 blue-green Foam Pieces from Side Panel packaging to use in a later step. Determine where you want to position Wall Bed. Place Head of Bed 18" from wall. Lay out other pieces as shown below. e n d l l d d
bunk bed 29" x 74" opt. skylight opt. shirt ward opt. 066 garage door opt. 846 bunk bed dinette 40" x 72" . pegasus floor plans queen bed 60" x 74" refer shelf pass-through storage ward pedestal table night dinette stand 37" x 57" . and free standing dinette twin bed 36" x 74" double bed 48" x 74" storage ward refer tv cab. skylight dinette .
Pipe Size ASTM Designation (in) (mm) (D2310) (D2996) 2 - 6 50 - 150 RTRP 11FX RTRP 11FX-5430 8 - 16 200 - 400 RTRP 11FX RTRP 11FX-3210 Fittings 2 to 6-inch Compression-molded fiberglass reinforced epoxy elbows and tees Filament-wound and/or mitered crosses, wyes, laterals and reducers 8 to 16-inch Filament-wound fiberglass reinforced epoxy elbows Filament-wound and/or mitered crosses, wyes .
