2018 OWNER S MANUAL FOR LB S S TAINLESS TEEL SPREADER
2018OWNER'S MANUAL FOR 135LBSTAINLESS STEEL SPREADERSNOWRATORAESL. T. RICH PRODUCTS11/2/2018
135lb Stainless Steel Spreader InstallationREV5TABLE OF CONTENTS1.0SHIPPING CONTENTS . 22.0IMPORTANT INFORMATION . 32.12.22.32.42.53.0TOOLS & EQUIPMENT .6INSTALLATION . 74.14.24.34.44.55.0OVERVIEW .3SAFETY .3MAINTENANCE . 4RELATED DOCUMENTS . 4INSTALLATION . 53.14.0ABOUT THIS MANUAL . 3FERTILIZER BOXES .7SPREADER .11SPEED CONTROL UNIT .14AUX CONTROL PANEL .15TEST .17OPERATION . 185.15.25.3OPERATIONAL CONTROLS .18SPREAD PATTERN ADJUSTMENT CONTROLS .20SPREAD PATTERN SET-UP .246.0TROUBLESHOOTING . 267.0PARTS LIST . 298.0AUX ELECTRICAL WIRING HARNESS DIAGRAM . 33For any questions please contact us at toll free (877) 482-2040 Mon-Fri 8 a.m. to 4:30 p.m.1
REV5135lb Stainless Steel Spreader Installation1.0 SHIPPING CONTENTSSR-HOPPER KIT (135) SHIPPING LISTLTR P/NToro P143-0539AUX ELECTRICAL HARNESS1EA90205142-0216SPINNER SPEED CONTROLLER1EACB-381SS126-0980CARRIAGE BOLT, 3/8" x 1"4EACB-5161SSHDW17294CARRIAGE BOLT, 5/16" x 1"4EACB-51634SS126-0695CARRIAGE BOLT, 5/16" x 3/4"2EAFWSS-516HDW14535WASHER, 5/164EAHFNCS-10S142-0542SERRATED FLANGE LOCK NUT, 10-324EAHFNCS-38S135-2882HEX FLANGE NUT, 3/84EAN/AN/ARED ROCKER SWITCH ASSEMBLY1EAN/AN/AAUX CONTROL PANEL ASSEMBLY1EAN/AN/A135LB STAINLESS STEEL SPREADER1EASC1-0500-SS142-14501/2" SPLIT SHAFT COLLAR2EASM10193 TSSR143-0090HOPPER MOUNTING LATCH2EASM10401143-0366LEFT FERTILIZER BOX PLATFORM1EASM10402143-0367LEFT FERTILIZER BOX UPRIGHT1EASM10402-R143-0368RIGHT FERTILIZER BOX UPRIGHT1EASM10403143-0369RIGHT FERTILIZER BOX PLATFORM1EATRCP-1012S143-0542TRUSS SCREW, 10-32 x 1/24EAZB200305-L135-5470LEFT FERTILIZER BOX1EAZB200305-RW142-1953RIGHT FERTILIZER BOX1EAFor any questions please contact us at toll free (877) 482-2040 Mon-Fri 8 a.m. to 4:30 p.m.2
135lb Stainless Steel Spreader InstallationREV52.0 IMPORTANT INFORMATION2.1ABOUT THIS MANUALThe purpose of this manual is to assist you in properly and safely operating and maintaining the135lb Stainless Steel Spreader. Read and understand this entire manual before attempting to setup, operate, adjust, perform maintenance on, or store this attachment. This manual providesessential information and instructions, which will help you enjoy years of dependableperformance.The designed and tested safety of the 135lb Stainless Steel Spreader is dependent upon itsoperations within the parameters and limitations explained in this manual. Be familiar with andfollow all safety rules in this manual as well all safety rules for any related equipment, includingthe Snowrator.Although these instructions have been complied through extensive field experience andengineering data, some information presented herein may be generated in the nature due tounknown and/or varying operating conditions. However, these instructions, combined with yourincreased experience with the Snowrator, will enable you to develop procedures suitable to yourparticular application.The illustrations and data used in the manual were current at the time of printing, but theSnowrator and 135lb Stainless Steel Spreader may vary slightly due to ongoing engineeringchanges. L. T. Rich Products, Inc reserves the right to implement engineering and designchanges to the Snowrator as may be necessary without prior notification.2.2OVERVIEWThe 135lb Stainless Steel Spreader is an optional attachment that can be mounted to theSnowrator and used to spread salt/granular product. It has a variable speed electric motor whichallows variable spread distances from 6 to 25 feet. This depends on volume/density, particle sizeand rate of travel, and weather conditions. The pattern can be increased or decreased whilespreading depending on needs. Travel at a constant speed for consistent results.The 135lb Stainless Steel Spreader Attachment features stainless steel construction, electronicspeed control, vibrator, rate control and directional control.2.3SAFETYSafety is a primary concern in the design and manufacturing of all L. T. Rich Products.Unfortunately, our extensive efforts to provide safe equipment can be negated by a singlecareless act of an operator. In addition to the design and configuration of the 135lb StainlessSteel Spreader, hazard control and accident prevention are also dependent upon the awareness,condition, maintenance, and storage of the Snowrator and all optional attachments. This sectionis only for the 135lb. Stainless Steel Spreader. Please refer to the Owner's Manual for applicablesafety information for the Snowrator. Additional safety tips are provided throughout thisdocument.For any questions please contact us at toll free (877) 482-2040 Mon-Fri 8 a.m. to 4:30 p.m.3
135lb Stainless Steel Spreader InstallationREV5Safety Cont 2.3.1 Safety EquipmentWhen using or performing maintenance on the 135lb Stainless Steel Spreader, it is recommendedthat the operator wear gloves and safety glasses.2.3.2 Mounting and DismountingTwo people using proper lifting techniques are required to mount and dismount the 135lb.Stainless Steel Spreader. The risk of injury and/or damage to the unit is significantly increased ifonly one person is performing this activity.2.3.3 SpinnerTurn off the spinner before adjusting spread pattern settings. ALWAYS keep fingers, hands,loose clothing, etc. clear of this area when it is in use.2.3.4 OperationAlways scan the environment to ensure the product being spread does not come into contact withother people and animals. Do not spread within 25 feet of people or animals. Follow allguidelines provided in the Snowrator Owner's Manual.2.4MAINTENANCEFollow all safety guidelines when performing maintenance on the 135lb Stainless Steel Spreader.In order to ensure the 135lb. Stainless Steel Spreader is kept in optimum condition, perform thefollowing maintenance activities on a regular basis.DO NOT USE WATER WHEN CLEANING HOPPERDaily Clean debris and product from Hopper daily USING COMPRESSED AIR ONLY, toeliminate build up.Check daily to make sure guides (4) are not damaged to allow the hopper door to slidefreely.Weekly 2.5Lubricate Hopper cables with Silicone Spray weekly.RELATED DOCUMENTS Snowrator Owner’s ManualInstallation Guide for 135lb Stainless Steel Spreader Conversion Kit (SRA-10020)For any questions please contact us at toll free (877) 482-2040 Mon-Fri 8 a.m. to 4:30 p.m.4
135lb Stainless Steel Spreader InstallationREV53.0 INSTALLATIONWARNINGBefore Working on This Machine Switch Engine to OFF Please note that this installation guide is for a standard machineonly. The hose and electrical harness routing may be different depending onthe attachments that may already be installed on your machine. A SNOWRATOR machine is shown for all assembly photos. For any questions please contact us at toll free (877) 482-204 Mon-Fri8 a.m. to 4:30 p.m.For any questions please contact us at toll free (877) 482-2040 Mon-Fri 8 a.m. to 4:30 p.m.5
135lb Stainless Steel Spreader Installation3.1REV5TOOLS & EQUIPMENTITEMQTYDESCRIPTION11DRILL21DRILL BIT, 3/8"31RATCHET41SOCKET, 13/16"51EXTENSION, SOCKET, 1-1/2"66WRENCH: 3/8", 1/2", 5/16", 7/16", 9/16", 13/16"71ALLEN WRENCH, 1/8"81SCREWDRIVER, PHILLIPS, NO. 291UTILITY KNIFE101JACK, 1 TONITEMQTY11GLOVES21SAFETY GOGGLESDESCRIPTIONPHOTOPHOTOFor any questions please contact us at toll free (877) 482-2040 Mon-Fri 8 a.m. to 4:30 p.m.6
135lb Stainless Steel Spreader InstallationREV54.0 INSTALLATION4.1FERTILIZER BOXES4.1.1 Remove Rear Tires.Raise the machine using a Jack and Jack Stands (not shown).Remove both Rear Tires.Tools:Ratchet with 13/16”SocketBB4.1.2 Remove Rear Light Bracket.Remove the two Bolts connecting the Rear Light Bracket to the Frame.Lay Rear Light Bracket gently on the Frame (not shown).Tools:Ratchet with 1/2” SocketAFor any questions please contact us at toll free (877) 482-2040 Mon-Fri 8 a.m. to 4:30 p.m.7
REV5135lb Stainless Steel Spreader InstallationFertilizer Boxes Cont 4.1.3 Remove Battery Box.Tools:Ratchet with 1/2” SocketRemove battery cover by unhooking strap.Detach the Negative (black) and Positive (red) Wires from battery.Remove bolts that attach the Battery Box Bracket to the Frame.Remove Battery Box Bracket from Frame.ABC3cDFor any questions please contact us at toll free (877) 482-2040 Mon-Fri 8 a.m. to 4:30 p.m.8
135lb Stainless Steel Spreader InstallationREV5Fertilizer Boxes Cont 4.1.4 Attach the Right Fert Box PlatformTools:Ratchet with 9/16” SocketAInsert (2) 3/8” x 1” Bolt into Footplate BracketLine up Slot in Fert Box Platform with BoltsFasten with (2) 3/8” Flange Nuts.BCHand Tighten4.1.5 Attach the Battery Box BracketTools:Wrench, 1/2”Wrench, 9/16AReplace 5/16” x ¾” Bolts in Battery Box Bracket with 5/16” x 1” BoltsAlign Fert Box Platform to Fender and Battery Box BracketTighten all (4) Bolts to Foot Plate Bracket and FenderRe-Connect the Red Battery Cable (not shown)*** DO NOT CONNECT NEGATIVE (BLACK) BATTERY CABLEUNTIL READY TO TEST! ***BCFor any questions please contact us at toll free (877) 482-2040 Mon-Fri 8 a.m. to 4:30 p.m.9
135lb Stainless Steel Spreader InstallationREV5Fertilizer Boxes Cont 4.1.6 Attach the Left Fert Box PlatformTools:Ratchet with 9/16” SocketAInsert (2) 3/8” x 1” Bolt into Footplate BracketLine up Slot in Fert Box Platform with BoltsFasten with (2) 3/8” Flange NutsCBHand Tighten4.1.7 Attach Rear Light BracketTools:Wrench, 1/2”Wrench, 9/16AInsert (2) 5/16” x 1” Bolt into Rear Light BracketAlign Fert Box Platform to Fender and Rear Light BracketTighten all (4) Bolts to Foot Plate Bracket and FenderBCFor any questions please contact us at toll free (877) 482-2040 Mon-Fri 8 a.m. to 4:30 p.m.10
REV5135lb Stainless Steel Spreader InstallationFertilizer Boxes Cont 4.1.8Tools:Ratchet with 13/16”SocketAttach Rear TiresAttach Rear Tires.Lower Machine and remove Jack.Fertilizer Boxes Cont 4.2SPREADERThis section requires TWO people in order to install it safely. Always use safe liftingtechniques. Take care not to pinch fingers or drop the spreader during installation.4.2.1 Mount 135lb Stainless Steel SpreaderTools:Drill, 3/8” bitDrill out the quick-release pin hole on the Mounting Plate of SnowratorWith one person on each side, lift the 135lb Stainless Steel Spreader by theBack Shield and the rear of the Hopper.ABBBackFor any questions please contact us at toll free (877) 482-2040 Mon-Fri 8 a.m. to 4:30 p.m.Front11
135lb Stainless Steel Spreader InstallationREV5Mount Spreader Cont.Rest the rear of base on the Mounting plate with the front at a slightly elevatedangle.Slide the Hopper Hinge Rods down into the rear Mounting Plate hooks.CDDSet the front of base down so the Hopper Latch Rods are in the front MountingPlate Hook.EEEAttach Latches to the Hopper Latch Mounting Rods.FFFFor any questions please contact us at toll free (877) 482-2040 Mon-Fri 8 a.m. to 4:30 p.m.12
REV5135lb Stainless Steel Spreader InstallationMount Spreader Cont.Tools:Allen Wrench, 1/8”GSecure both Latches with a 1/2” Split Shaft Collar.Align 1/2” Split Shaft Collar so it is flush with the outer edge of the HopperLatch Rod and tighten.GHInsert a 3/8” Bolt through Hopper Latch, Base and Mounting Plate on bothsides of the Hopper Base.Set the Hopper Cable, Vibrator, Connector and Spinner Motor Connectoroff to the side (Not shown). These will be connected in the next section.IIFor any questions please contact us at toll free (877) 482-2040 Mon-Fri 8 a.m. to 4:30 p.m.13
REV5135lb Stainless Steel Spreader Installation4.3SPEED CONTROL UNIT4.3.1 Speed Control Unit, MechanicalRub Slot Edges to reveal Cut locationCut into Main Control Panel using utility knife and use a Die Grinder withcut-off wheel to cut tabs.Tools:Utility KnifeABbTools:Ratchet with 11/32 SocketPhillips ScrewdriverCInsert Speed Control Unit in the Main Control Panel Cutout.Insert (4) 10-32 x 1/2” Phillips Screws in Mounting Holes on Speed ControlUnitFasten to Main Control Panel with (4) 10-32 Flange NutsDbEUnder Control PanelFor any questions please contact us at toll free (877) 482-2040 Mon-Fri 8 a.m. to 4:30 p.m.14
135lb Stainless Steel Spreader InstallationREV5Speed Control Unit cont 4.3.2 Speed Control Unit, ElectricalPower and Ground1. Attach the connector labeled POWER to the Power Ground HarnessConnector labeled SPINNER.2. Attach the connector labeled MOTOR to the Spinner Motor Connector4.4AUX CONTROL PANEL4.4.1 Aux Control Panel, MechanicalInsert (1) 5/16” x 3/4” Carriage Bolt in the top Aux Control Panel mountinglocation.Position the Aux Control Panel on the bolt.Fasten with (2) 5/16” Washers and (1) Hand Knob.Insert (1) 5/16” x 3/4” Carriage Bolt in the bottom Aux Control Panelmounting location.Fasten with (2) 5/16” Washers and (1) Hand Knob.A4aB4DECCompleted InstallationFor any questions please contact us at toll free (877) 482-2040 Mon-Fri 8 a.m. to 4:30 p.m.15
135lb Stainless Steel Spreader InstallationREV5Aux Control Panel Cont 4.4.2 Aux Control Panel, ElectricalSwitch Connector1. Connect the Switch Connector on the Electrical Harness to the connectoron the back of the Vibrator Switch.AAll BlackPower and Ground1. Attach the Vibrator Power & Ground Connector to the Power/GroundHarness Connector labeled VIBRATOR.Vibrator Switch Connector1. Connect the Vibrator Switch Connector from the Aux Electrical Harnessto the Vibrator Motor.DGreen TrimFor any questions please contact us at toll free (877) 482-2040 Mon-Fri 8 a.m. to 4:30 p.m.16
135lb Stainless Steel Spreader Installation4.5REV5TESTConnect the Negative (black) Battery Cable before testing. Refer to section 5 for OperatingInstructions.4.5.1 VibratorVerify the electrical connections have been made properly.Turn on the Vibrator. Listen for vibration.Turn off the Vibrator.4.5.2 Speed Control UnitVerify the electrical connections have been made properly.Press the top right button to start the spinner.Press the top left button to turn off the spinner.4.5.3 Plow ClearanceMove the lift cylinder lower pin to the upper hole in the A-Frame then, check for clearancebetween the plow and the Directional Control after each step. The plow should have clearancewhen the Directional Control is open at its minimum and maximum positions (See Section5.2.2). Refer to the Snowrator Owner’s Manual for instructions on moving the plow.Raise the plow to its maximum upward position.Adjust the plow all the way to the left.Adjust the plow all the way to the right.Return the plow to the center position.For any questions please contact us at toll free (877) 482-2040 Mon-Fri 8 a.m. to 4:30 p.m.17
REV5135lb Stainless Steel Spreader Installation5.0 OPERATION5.1OPERATIONAL CONTROLSThe 135lb Stainless Steel Spreader has four controls. These are the Vibrator Switch, SpinnerSwitch, Spinner Speed Control, and Hopper Cable. These controls can be operated while thespreader is in use.5.1.1 AUX Control PanelThe Hopper Cable is located to the left of the Vibrator Switch. This Cable opens the HopperDoor when pulled upward and closes the Hopper Door when pushed downward. The HopperCable will only open as far as the Rate Control setting will allow.The Vibrator Switch is located to the right of the Hopper Cable. It has a built-in light thatindicates when it is on. Pressing the top of the switch will turn on the Vibrator mounted behindthe Hopper. Pressing the bottom will turn it off.Figure 1. Hopper Door Cable and Vibrator Switch locationHopper Door CableVibratorFor any questions please contact us at toll free (877) 482-2040 Mon-Fri 8 a.m. to 4:30 p.m.18
REV5135lb Stainless Steel Spreader InstallationOperational Controls Cont 5.1.2 Main Control PanelThe Main Control Panel is where the Speed Control Unit for the Spinner Motor is located. Theunit has an ON/OFF button, speed adjustment controls and an LED indicator strip. The LEDindicators alert the operator of malfunctions when they flash in specific patterns. See thetroubleshooting section for more information.Power is applied to or removed from the unit by pressing the ON/OFF button. Speed Control isadjusted via the TURTLE and RABBIT buttons on the Speed Control Unit. Pressing theTURTLE button reduces Spinner speed and pressing the RABBIT button increases it. Seesection 5.2.2.In extreme cold the grease in the spinner motor gearbox may cause the controller to error out dueto too high of a current draw. The controller has a cold start sequence that will warm the motorup and allow the user to run the spreader normally in these conditions. If at any time you need toexit the COLD START SEQUENCE press the OFF button. The next time the controller isstarted it will be in normal operating mode.1.2.3.4.Close the feed gate to prevent material loss.Turn off the spreaderCheck to make sure there are no obstructions around the spinner disk.To activate the COLD START SEQUENCE, press and hold the turtle and rabbit thenpress the power button and release all three. The LED lights will scroll across thecontroller from left to right letting you
Snowrator and 135lb Stainless Steel Spreader may vary slightly due to ongoing engineering changes. L. T. Rich Products, Inc reserves the right to implement engineering and design changes to the Snowrator as may be necessary without prior notification. 2.2 OVERVIEW The 135lb Stainless Steel Spreader is an optional attachment that can be mounted .
Bruksanvisning för bilstereo . Bruksanvisning for bilstereo . Instrukcja obsługi samochodowego odtwarzacza stereo . Operating Instructions for Car Stereo . 610-104 . SV . Bruksanvisning i original
10 tips och tricks för att lyckas med ert sap-projekt 20 SAPSANYTT 2/2015 De flesta projektledare känner säkert till Cobb’s paradox. Martin Cobb verkade som CIO för sekretariatet för Treasury Board of Canada 1995 då han ställde frågan
service i Norge och Finland drivs inom ramen för ett enskilt företag (NRK. 1 och Yleisradio), fin ns det i Sverige tre: Ett för tv (Sveriges Television , SVT ), ett för radio (Sveriges Radio , SR ) och ett för utbildnings program (Sveriges Utbildningsradio, UR, vilket till följd av sin begränsade storlek inte återfinns bland de 25 största
Hotell För hotell anges de tre klasserna A/B, C och D. Det betyder att den "normala" standarden C är acceptabel men att motiven för en högre standard är starka. Ljudklass C motsvarar de tidigare normkraven för hotell, ljudklass A/B motsvarar kraven för moderna hotell med hög standard och ljudklass D kan användas vid
LÄS NOGGRANT FÖLJANDE VILLKOR FÖR APPLE DEVELOPER PROGRAM LICENCE . Apple Developer Program License Agreement Syfte Du vill använda Apple-mjukvara (enligt definitionen nedan) för att utveckla en eller flera Applikationer (enligt definitionen nedan) för Apple-märkta produkter. . Applikationer som utvecklas för iOS-produkter, Apple .
Test Name Score Report Date March 5, 2018 thru April 1, 2018 April 20, 2018 April 2, 2018 thru April 29, 2018 May 18, 2018 April 30, 2018 thru May 27, 2018 June 15, 2018 May 28, 2018 thru June 24, 2018 July 13, 2018 June 25, 2018 thru July 22, 2018 August 10, 2018 July 23, 2018 thru August 19, 2018 September 7, 2018 August 20, 2018 thru September 1
er's Manual and the following Owner's Man‐ uals: Integrated Owner's Manual in the vehicle. Online Owner's Manual. MINI Motorer’s Guide App. Notes on updates can be found in the appendix of the printed Owner's Manual for the vehicle. Owner's Manual for Navigation, Entertainment, Communication Owner's Manual for Navigation, Entertainment,
och krav. Maskinerna skriver ut upp till fyra tum breda etiketter med direkt termoteknik och termotransferteknik och är lämpliga för en lång rad användningsområden på vertikala marknader. TD-seriens professionella etikettskrivare för . skrivbordet. Brothers nya avancerade 4-tums etikettskrivare för skrivbordet är effektiva och enkla att
