TRIMBLE TO 12D V8 - 12d Model
12d Model v8 interface to Trimble instruments2007These notes describe the interfacing of 12d version 8 with the Trimble surveying instruments.1) Installing Trimble linkTrimble link must be installed prior to attempting to upload or download data to the Trimble controller. Theuser will need to have access to the internet and have administrator rights1.1) Installing the softwarep2-41.2) Registering the softwarep5-71.3) Updating Data Transfer softwarep82) Uploading2.1)Point coordinates (Job file)p 9 – 112.2)Point coordinates (Linked file)p 12 - 142.3)DXF file for backgroundp 15 - 172.4)DXF file for stakeoutp 18 - 202.5)TINp 21 - 222.6)Road sections and strings (Simple Road) p 23 - 242.7)Road Strings (Complex Road)p 25 - 26Trimble linkp 27 - 313) Downloading3.1)Page 1
12d Model v8 interface to Trimble instruments1Trimble link1.1 Installing Trimble link (Administrator rights needed)Insert the 12d v8 installation cdSelect the Other Software tabPage 22007
12d Model v8 interface to Trimble instrumentsSelect Install to begin the install processSelect NextSelect Yes to accept the licence agreementPage 32007
12d Model v8 interface to Trimble instrumentsSelect Finish to end the installPage 42007
12d Model v8 interface to Trimble instruments1.22007Registering Trimble linkThe first time Trimble link is run you need to register the software. Ensure you are connected to the internetIn 12d select option Survey Setup to select the data collector typeSelect the data collector choice icon then select Trimble Link Feature StringSelect Set then FinishPage 5
12d Model v8 interface to Trimble instrumentsSelect option Survey Download RawSelect DownloadAn authorisation code is required. To register click on the link to the Trimble web pagePage 62007
12d Model v8 interface to Trimble instruments2007The registration page appears. Scroll down to the bottom of the page and fill in your details. Select SendRegistration NowA registration number will be sent straight away. Record this number for entry into the Registration panelExit the panel and return to the Registration panelType in the Registration number, Select Yes, I Agree to accept the licence then select OKSelect Close to exit the Tips panelTrimble Link is now registered. Proceed to the relevant chapter to upload / download dataPage 7
12d Model v8 interface to Trimble instruments1.32007Updating Data Transfer softwareAs the data transfer software is provided by Trimble any updates need to be downloaded from the TrimbleWeb page link belowhttp://www.trimble.com/datatransfer.shtmlor by selecting Trimble Data Transfer Utility in the Survey Data Download panelInstallation instructions are included on the Web PagePage 8
12d Model v8 interface to Trimble instruments22007Uploading from 12d to the Trimble controller2.1 Point coordinates (Job file)Create the point numbers for the setout points as per the Getting Started For Surveyors manual chapter11.1.5Connect the controller to the computer by an approved method then select optionSurvey Upload Create points upload file (new)Tick the check box to upload directly to the controllerSelect the data to upload using one of the sourcebox optionsTick the check box to only upload numericpoint numbers if you have no letters in the pointnumbers. This allows you to edit the numberrangeSelect WritePage 9
12d Model v8 interface to Trimble instrumentsSelect OK to accept the warning regarding the coordinate systemSelect the controller for uploading then select OpenType in the file name to create then select SavePage 102007
12d Model v8 interface to Trimble instruments2007The file can now be opened and viewed in the controllerTo create an upload of strings or to have the shape of the house along with the text see sections on creatingstring uploads and dxf file uploadsPage 11
12d Model v8 interface to Trimble instruments20072.2 Point coordinates (Linked file)A linked file of coordinates can be created and uploaded to the controller for setout. The benefit of a linked fileis that it is not included in the download of points from the controller.Create the point numbers for the setout points as per the Getting Started For Surveyors manual chapter11.1.5Create comma delimited (csv) file of point coordinatesSelect option File I/O Data Output Write xyz generalSelect data to listType in file nameSet Delimiter to commaSet up order of dataSelect Write
12d Model v8 interface to Trimble instrumentsCopy the csv file to the controller using Active Sync and Windows Explorer.Refer to Trimble documentation for target location of fileOn the controller open the job to setoutSelect Files Open Job then pick the required jobPage 132007
12d Model v8 interface to Trimble instrumentsSelect File Properties of current jobSelect Linked files then select csv file to linkThese points can then be set out in the stakeout menuPage 142007
12d Model v8 interface to Trimble instruments2.3 DXF file for backgroundA dxf file can be used as a background on the controllerSelect option File I/O Data Output DWG/DXF/DXBSelect data to listSelect dxf as formatType in file nameSet version Autocad 2004Select 2dType in scale for text appearance12d Model v7 interface to Trimble instruSelect Writements2007
12d Model v8 interface to Trimble instrumentsCopy the dxf file to the controller using Active Sync and Windows Explorer.Refer to Trimble documentation for target location of fileOn the controller open the job to setoutSelect Files Open Job then pick the required jobPage 162007
12d Model v8 interface to Trimble instrumentsSelect File Properties of current jobSelect Active map then select dxf file. The layers can be then toggled on or offThe strings and text can then be seen in the display along with the setout pointsPage 172007
12d Model v8 interface to Trimble instruments2.4 DXF file for setoutA dxf file can also be used for setout of stringsSelect option File I/O Data Output DWG/DXF/DXBSelect data to listSelect dxf as formatType in file nameSet version Autocad 2004Select 3d12d Model v7 interface to Trimble instruSelect Write2007
12d Model v8 interface to Trimble instrumentsCopy the dxf file to the controller using Active Sync and Windows Explorer.Refer to Trimble documentation for target location of fileOn the controller open the job to setoutSelect Files Open Job then pick the required jobPage 192007
12d Model v8 interface to Trimble instrumentsSelect File Properties of current jobSelect Active map then select dxf file. The layers can be then toggled on or offThe strings can then be seen in the display and used for 2d / 3d setoutPage 202007
12d Model v8 interface to Trimble instruments2.52007TIN uploadSelect option Survey Upload Create triangle upload fileSelect File Type Trimble binary *.ttmTick the check box to Use Trimble LinkTick check box to Upload directly to Trimble deviceType in a TIN name to create on the controllerType in the TTM output file nameSelect the TINSelect the polygon around the edge of the TINSelect WriteSelect Yes to confirm the number of trianglesPage 21
12d Model v8 interface to Trimble instrumentsSelect the controller then select OpenType in the file name and select appropriate file format version if applicableSelect SaveThe TIN can now be used for height when setting out using the controllerPage 222007
12d Model v8 interface to Trimble instruments2.6 Road sections and strings (Simple road)Create upload file for road alignment and associated sectionsSelect option Survey Upload Create Road upload file (new)Select File Type Trimble LinkTick check box to Upload directly to Trimble deviceSelect the Alignment stringType in the road nameTick check box to Report vertical alignmentTick check box to Report X-sectionsSelect the model for the cross sectionsSelect WriteSelect OK to accept the warningSelect the controller then select OpenPage 232007
12d Model v8 interface to Trimble instrumentsType in the Road name to create then select SaveThe road can now be set out using the controllerPage 242007
12d Model v8 interface to Trimble instruments20072.6 Road strings (Complex road)The genio format is used to create an upload file with alignment strings and design strings. This is done in two partsCreate genio file of alignmentSelect alignment stringType in file nameChange alignment/arc dimension to 6dTick check box for 77 formatSelect WriteDON’T FINISH PANEL YET!Select model for road stringsKeep previous file nameChange alignment/arc dimension to 3dSelect WriteSelect Yes to append to the existing filePage 25
12d Model v8 interface to Trimble instrumentsCopy the genio file to the controller using Active Sync and Windows Explorer.Refer to Trimble documentation for target location of fileOn the controller the genio file can be selected when in the Roads Stakeout menuPage 262007
12d Model v8 interface to Trimble instruments3Downloading3.1 Setting up data collectorSelect option Survey SetupSelect the Data collector choice icon then select Trimble Link Feature StringSelect Set then FinishPage 272007
12d Model v8 interface to Trimble instruments3.2 Downloading raw dataSelect Survey Download rawIf downloading data from gps file the data can be reduced as vectors from the base station or by tickingthe “Download as reduced coords” are reduced as coordinatesThe advantage of downloading as vector observations is the ability to change target heightsIf the controller software has been recently updated the Trimble link software should also be updated.To do this click on the hyper link Trimble Data Transfer Utility to go to the Trimble web page and followthe instruction2007
12d Model v8 interface to Trimble instrumentsSelect Download to start the download processSelect the Survey Controller then select OpenSelect the detail survey file then select OpenPage 292007
12d Model v8 interface to Trimble instruments2007The raw file can be edited here prior to creating the field fileTo finish the editing and convert to a field file select OKThe procedures for reducing the field file are given in chapter 9.4.5 of the Getting Started For Surveyors manualPage 30
12d Model v8 interface to Trimble instruments 2007 Page 9 2 Uploading from 12d to the Trimble controller 2.1 Point coordinates (Job file) Create the point numbers for the setout points as per the Getting Started For Surveyors manual chapter 11.1.5 Connect the controller
Trimble DiNi Digital Level . 20 Trimble Controllers Trimble CU . 22 Trimble Tablet . 24 Trimble TSC3 . 26 Trimble Imaging Solutions Trimble TX8 . Worldwide centimeter level positioning using Trimble
Al-Rajhi Advanced Construction L.L.C Trimble NetR9 CORS STATION 2012 Riyadh Geotechnique & Foundations Co Trimble NetR9 CORS STATION 2012 King Abdullah University of Science & Technology Trimble Products Dini Digital Level 2012 Madinah Municiplaity Trimble R6GNSS / Trimble S3 Total Station 2012 Al-Saa
12d Model Training 12d NZ Ltd Training Courses Page 1 1.0 TRAINING OVERVIEW 12d Model has been training users for over 25 years, and as such are committed to refining our training methods, not only as the product develops, but also from the feedback that we receive after every
trimble s5 total station. ТАХЕОМЕТР trimble s5. . Тахеометр trimble s5 является ЛАЗЕРНЫМ ПРИБОРОМ КЛАССА2. В данном инструменте имеются источники видимого и невидимого лазерного излучения,
Trimble Recon Handhelds (WM 5.0) From the Trimble Recon “Getting Started Guide” (pages 11-12) Note: These instructions are designed for the Trimble Recon running Windows Mobile 5. To reset Trimble Recon devices running an operating system other than Windows Mobile
Trimble solutions manage 1T in construction 70% of top 100 geospatial companies use Trimble 2M transportation assets managed with Trimble Solutions Overseeing 155M acres of agriculture Trimble solutions deliver millions of metric tons of avoided greenhouse gas emissions annually Top 10
Part Number Description Product Line RoHS Min Order Qty List Price (USD) Discount New York Net Price (USD) TRIMBLE Products 560580100 Instrument - Trimble 5605 (5'') Servo Total Station, DR Standard, w/Laserpointer 5600 SERIES Complies w/EU Directives 1 10,200.00 10% 9,180.00 560584100 Instrument - Trimble 5605 (5'') Autolock Total Station, DR Standard,
Abrasive Jet Micro Machining (AJMM) is a relatively new approach to the fabrication of micro structures. AJMM is a promising technique to three-dimensional machining of glass and silicon in order to realize economically viable micro-electro-mechanical systems (MEMS) It employs a mixture of a fluid (air or gas) with abrasive particles. In contrast to direct blasting, the surface is exposed .
