CSN-A2 Micro Panel Printer's User Manual
1/70CSN-A2 User manualCSN-A2 Micro panel printer'sUser ManualVersion4.0
2/70CSN-A2 User manualContentCAUTIONS . 31 General Specifications. 42 Features . 43 Printer outline pictures and dimension . 53.1 Outline pictures . 53.2 Dimension. 54 Operation specifications and print test . 64.1 Operation specifications . 64.2 Printing test . 75 Connector . 75.1 TTL or RS232 connector . 75.2 Parallel connector . 85.3 USB connector . 95.3.1 J3 Power supply connector . 95.3.2 CN4 TTL connector . 95.3.3 CN3 USB /MINID connector. 95.3.4 J2 Integrated Keyboard functions: . 106 printer functions . 107 Using attention . 118 ESC/POS Printing Command Set . 118.1 Command list . 118.2 Command Detail. 138.2.1 Print Commands . 138.2.2 Line spacing setting commands. 168.2.3 Character Setting Commands . 188.2.4 Bit Image Command . 298.2.5 Init command . 408.2.6 Status Command. 408.2.7 Bar Code Command. 428.2.8 Miscellaneous Function Command. 478.2.9 New commands . 49Appendix 1 Code page . 54Appendix 2 International character set: . 69
CSN-A2 User manual3/70CAUTIONS1. This document shall apply only to the product(s) identified herein.2. No part of this document may be reproduced, stored in a retrieval system, ortransmitted in any form or by any means, electronic, mechanical, photocopying, recording,or otherwise, without the prior written permission of Kashino Technology Limited.3. The contents of this document are subject to change without notice. Please contact usfor the latest information.4. While every precaution has been taken in the preparation of this document, KashinoTechnology Limited assumes no responsibility for errors or omissions.5. Neither is any liability assumed for damages resulting from the use of the informationcontained herein.6. Kashino Technology Limited shall be not liable to the purchaser of this product or thirdparties for damages, losses, costs, or expenses incurred by the purchaser or third partiesas a result of: accident, misuse, or abuse of this product or unauthorized modifications,repairs, or alterations to this product, or failure to strictly comply with Kashino TechnologyLimited 's operating and maintenance instructions.7. Kashino Technology Limited shall not be liable against any damages or problemsarising from the use of any options or any consumable products other than thosedesignated as Original Kashino Products or Kashino Approved Products by KashinoTechnology Limited.
4/70CSN-A2 User manual1 General SpecificationsITEMSPECIFICATIONPrint methodthermal direct line printingPaper loading methodeasy paper loadingPaper width58mmPrint width48mmResolution ration8dots/mm(384dots/line)Life of printing head50kmPrinting speed60mm/sec.; Max.:80MM/sec.(voltage 8.5V）Character sizeANK: 9x17,12 24; GBK: 24 24Chinese character fontsGB18030: 12x24 or 24x24dotsOutline dimension（WxHxD mm)111x65x57Installation(WxH mm):103x57Embedded depth50 mmPaper roll specification(width:58mm, Max. t powerDC5-9V or 12VOperating temperature5 C 50 CStorage temperature-20 C 60 COperating humidity10 C 80 CStorage humidity10 C 90 C2 Features Low-noise direct thermal printing methodPrinter control panel built-in ANK character or GB18030 Chinese character,thoroughly remove the uncommon words of anguishFast printing speed, low noiseCan support Max.39mm (diameter) paper roll, which is biggest paper roll of the samemodels.Optional serial interface (RS232C/TTL)/parallel/USB portRich of graphics / curves / characters print functionEasy paper loading structureSupport 5V-9V/12V wide power voltage
CSN-A2 User manual3 Printer outline pictures and dimension3.1 Outline pictures Outline dimension: 111W*65D*57H mmFront panel Size: 103 W*57H mmEmbedded depth: 50 mmMax diameter of paper roll: 39 mm3.2 DimensionOutline is as follows:5/70
CSN-A2 User manual6/70The installation method:Put the panel printer into the front of the device as per Fig.1 and Fig.2,and then installfixed block and screwing as per Fig.3Note: have 1 to 6mm variation in thickness.4 Operation specifications and print test4.1 Operation specificationsA. the instruction of indicator lightPower on, the indicator light will flash 2 times, interval 1sec, it say the startness is OK, and
7/70CSN-A2 User manualthen the instructions for the indicator light as below: Blink once:Work well (Stay lit for some customized board) Blink twice:Printer mechanism is ununited or temperature is too low. Blink three times:No paper is detected Blink four times:Cutter is wrong (Just for board with cutter) Blink five times:Printer mechanism is overheat Blink six times:Roller didn't press well. (Just for board with roller detection. Blink ten times:Flash device is wrong for the boardB. key instructionThe key on the panel printer is FEED keyC. how to change new paper rollerBefore changing, turn up the switch, and put into the paper roller4.2 Printing testPower on, press the [feed] key, for a while, relax the key, it will print out one testingsample.Power on, press key per time, it will feed the paper.5 ConnectorThe user has option of RS232, TTL, USB and LPT interface.5.1 TTL or RS232 connectorThe define of the PIN of the interface for RS232, TTL as the following:PinnumberSignal name1GND(Ground)2NULL
8/70CSN-A2 User manual3VH(input voltage ，5V-9V)4GND(Ground)5RXD(receive data)6TXD( send data)5.2 Parallel connectorThe define of the Pin of LPT interface as below:1GND， Ground2VH，input voltage，5V-9V3 5V，input voltage (general condition, only use 5Vm VH not input )4the definition of the Pin of LPT interface as below:1. STROBE2-9. DATA0-DATA710. ACKNLG11. BUSY12. PEpaper out13. SLCT selection14. AUTO FEED auto change line15. ERROR16. INIT17. SLCT IN18-26. GND
9/70CSN-A2 User manual30.00mm6.00mm37.00mm5.3 USB connector5.3.1 J3 Power supply connectorPin numberSignal name1VH2GND5.3.2 CN4 TTL connectorPin numberSignal name1 3.3V2Transmit data (TXD, printer output)3Receive data (RXD, printer input)4GND5.3.3 CN3 USB /MINID connectorPin numberSignal name1VUSB2D-3D 4NC5GND
10/70CSN-A2 User manual5.3.4 J2 Integrated Keyboard functions:Pin numberSignal name1LED2 3.3V3 3.3V4KEY FEED6 printer functionsCN1Pin numberSignal nameFPC30/1.0Function1PHKCathode of photo interruptor2VSENPhoto-sensor power3PHEEmittor for photo interruptor4MT/B--Step motor excitation signal5MT/BStep motor excitation signal6MT/AStep motor excitation signal--7MT/AStep motor excitation signal8VHHead driver power9VHHead driver power10DIData input11CLKAynchronous clock for communication12GNDGround power supply for thermal head13GNDGround power supply for thermal head14STB6Thermal head energizing control signal15STB5Thermal head energizing control signal16STB4Thermal head energizing control signal17VDDLogic power18TMThermally sensitive resistor input terminal 119TMThermally sensitive resistor input terminal 220STB3Thermal head energizing control signal21STB2Thermal head energizing control signal22STB1Thermal head energizing control signal23GNDGround power supply for thermal head24GNDGround power supply for thermal head25\LATData Latch26DOData output27VHPower supply for thermal head28VHPower supply for thermal head29N.C(101)SW1(103)Platen release switch30N.C(101)SW2(103)Platen release switch
11/70CSN-A2 User manual7 Using attention7.1 Please notice, the ESD wrist ring and the humidity manufatures ETC, when using theprinter, to protect the inner elctrontic parts of the printer from the damage of ESD, becausethe TPH of the Printer and photoelectric sensor are ESD Sensitive parts.7.2 For protecting plastic shaft, don’t smear any oil or others on the rubber parts.7.3 Don’t touch the TPH, TPH having the palm oil, will induce the usage of the printer.Ifany oil or others in the TPH, pls using an alcohol cotton stick clean the area betweenplastic shaft and printer head at once.PS,Don’t strike the TPH.7.4 Due to the printer is easy-paper structure,you need pick up the rubber stick only pushthe rubber stick.So,if the paper jam,push harder will cause the rubber stick gearwheeldamaged.so pls don’t push the paper harder, pls do open the cover and re-fill the paper7.5 The temperature of the TPH protection must be below 65 , if you printcontinously,Because the exterior of the temperature of the IC protection & motor can’t notover 90 to protect the motor thread ring.7.6 Pls use the good quality paper, because the sensetive of the paper will infuence printeffect, meanwhile, rough paper will incease the excessive wear to the printer head, andreduce the life of the printer.8 ESC/POS Printing Command Set8.1 Command listTypePrint CommandsCommandNameLFCRHTFFESC DPrint and line feedESC J nPrint and Feed n dots paperESC d nESC nESC 2ESC 3 nLine spacing settingESC a nCommandsGS L nL nHESC nL nHPrint and carriage returnHorizontal tabPrint the data in bufferSet horizontal tab positionsPrint and Feed n linesSet peripheral deviceSelect default line spacingSet line spacingSelect justificationSet left marginSet absolute print position
12/70CSN-A2 User manualESC B nESC ! nGS ! nGS B nESC V nESC G nESC E nESC SP nESC SO nESC DC4 nCharacter SettingESC { nCommandsESC - nESC % nFS &FS .FS ! nESC &ESC ? nESC R nESC t nESC *GS *GS / nGS vBitImageDC2 *CommandsDC2 VDC2 vFS p n mFS q nInit CommandsESC @GS r nGS a nStatus CommandsESC v nESC u nGS H nGS h nBarCodeGS w nCommandsGS kGS x nESC 7 n1 n2 n3MiscellaneousESC 8 n1 n2function commands ESC 9 nDC2 # nSet Left SpaceSelect print mode(s)Select character sizeTurn white/black reverse printing modeTurn 90 clockwise rotation mode on/offTurn on/off double-strike modeTurn emphasized mode on/offSet right-side character spacingSelect Double Width modeDisable Double Width modeTurns on/off upside-down printing modeSet the underline dots(0,1,2)Select/Cancel user-defined charactersSelect Kanji character modeCancel Kanji character modeSet print mode for Kanji charactersDefine user-defined charactersCancel user-defined charactersSelect and international character setSelect character code tableSelect bit-image modeDefine downloaded bit imagePrint downloaded bit imagePrint raster bit imagePrint the bitmapPrint MSB bitmapPrint LSB bitmapPrint NV bitmapDefine NV bitmapInitialize printerTransmit statusEnable/Disable Automatic Status Back(ASB)Transmit paper sensor statusTransmit peripheral device status (For drawer)Select printing position for HRI charactersSet bar code heightSet bar code widthPrint bar codeSet barcode printing left spaceSetting Control Parameter CommandSelect sleeping parameterSelect Chinese code formatSet printing density
13/70CSN-A2 User manualDC2 TFS t nDC2 EDC2 m d lL lHESC C nGS FFNew commandsPrinting test pageSelect Time out (for CB105B)Feed Paper to MarkSet Mark paper lengthSet BM Max (For BM)Feed marked paper to print starting position(For BM)ESC iESC mCut Paper (For cut)GS VESC p mESC c 5GS ( FFS CFS SFS sFS dSelect cut mode and cut paper (For cut)Partial Cut Paper (For cut)Generate pulse (For drawer)Enable/disable panel buttons (For button)Set adjustment values(s) (For 701BM)Start receive buffer count (For cb65c)Send receive buffer count(For cb65c)save print parameter (for XBLY)Load default leaving factory set (for XBLY)8.2 Command Detail8.2.1 Print nce]Print and line feedASCII:LFDecimal:10Hexadecimal:0APrints the data in the print buffer and feeds one line, based on the currentline spacing.This command sets the print position to the beginning of the line.ESC 2, ESC int and carriage returnASCII:CRDecimal:13Hexadecimal:0DWhen automatic line feed is enabled, this command functions the sameas LF; when automatic line feed is disabled, this command is ignored. This command line feed is ignored with a serial interface model. Sets the print starting position to the beginning of the line.LF
14/70CSN-A2 User al tabASCII:HTDecimal:9Hexadecimal:09Moves the print position to the next horizontal tab position. This command is ignored unless the next horizontal tab position hasbeen set. If the next horizontal tab position exceeds the printing area, theprinter sets the printing position to [printing area width 1]. Horizontal tab positions are set with ESC D. [Reference]If this command is received when the printing position is at [printingarea width 1], the printer executes print buffer-full printing of thecurrent line and horizontal tab processing from the beginning of thenext line.ESC DFF[Name][Format]Print the data in buffer and locate to the next black markASCII:FF[Description]Decimal:12Hexadecimal:0c Print the data in the buffer. Locate to the black mark.Only board with black mark function support this command.[Note]ESC D n1.nk NUL[Name][Format][Range][Description][Note]Set horizontal tab positionsASCII:ESC D n1.nk NULDecimal:27 68 n1 nk 00Hexadecimal:1B 44 n1 nk 001 n 2550 k 32Set horizontal tab positions. n specifies the column number for setting a horizontal tab positionfrom the beginning of the line. k indicates the total number of horizontal tab positions to be set. The horizontal tab position is stored as a value of [character width n]measured from the beginning of the line. The character widthincludes the right-side character spacing, and double-width
15/70CSN-A2 User manual characters are set with twice the width of normal characters.This command cancels the previous horizontal tab settings.When setting n 8, the print position is moved to column 9 bysending HT.Up to 32 tab positions (k 32) can be set. Data exceeding 32 tabpositions is processed as normal data.Transmit [n]k in ascending order and place a NUL code 0 at the end.When [n]k is less than or equal to the preceding value [n]k-1, tabsetting is finished and the following data is processed as normaldata.ESC D NUL cancels all horizontal tab positions. [Default][Reference]The previously specified horizontal tab positions do not change,even if the character width changes. The character width is memorized for each standard mode.The default tab positions are at intervals of 8 characters (columns 9, 17,25.) for Font A (12 24).HTESC J n[Name][Format][Range][Description][Notes]Print and feed paperASCII:ESCJnDecimal:27 74 nHexadecimal:1B 4A n0 n 255Prints the data in the print buffer and feeds the paper [n 0.125 mm(0.0049”)]. After printing is completed, this command sets the print startingposition to the beginning of the line. The paper feed amount set by this command does not affect thevalues set by ESC 2 or ESC 3. In standard mode, the printer uses the vertical motion unit (y).ESC d n[Name][Format]Print and feed n linesASCII:[Range][Description]Decimal:27 100 nHexadecimal:1B64 n0 n 255Print the data in the buffer and feed paper n lines.ESCdn
16/70CSN-A2 User manual[Notes][Reference] This command sets the print starting position to the beginning of theline. This command does not affect the line spacing set by ESC 2 or ESC3. The maximum paper feed amount is 1016 mm (40 inches). If thepaper feed amount (n line spacing) of more than 1016 mm (40inches) is specified, the printer feeds the paper only 1016 mm (40inches).ESC 2, ESC 3ESC n[Name][Format][Description]Set peripheral deviceASCII:ESCDecimal:Hexadecimal:Set peripheral device:271B 613dnnnBitOff/OnHexDecimal Function0Off000Printer offline, not receive print data.On011Printer online, receive print data.---Undefined.1-78.2.2 Line spacing setting commandsESC 2[Name][Format]Select default line spacingASCII:ESC 2[Description][Note][Reference]Decimal:27 50Hexadecimal:1B 32Selects 3.75 mm (30 0.125 mm) line spacing.The line spacing can be set independently in standard mode.ESC 3 nESC 3 n[Name][Format][Range][Description][Note]Set line spacingASCII:ESC 3 nDecimal:27 51 nHexadecimal:1B 33 n0 n 255Sets the line spacing to [n 0.125 mm]. The line spacing can be set independently in standard mode. In standard mode, the vertical motion unit (y) is used.
17/70CSN-A2 User manual[Default][Reference]n 30ESC 2ESC a n[Name][Format][Range][Description]Select justificationASCII:Decimal:27 97 nHexadecimal:1B 61 n0 n 2, 48 n 50Aligns all the data in one line to the specified position.n selects the justification as follows:nJustification0,48Left justification1, 49Centering2, 50Right justification[Note] [Default][Example]ESC a nThe command is enabled only when processed at the beginning ofthe line in standard mode.This command executes justification in the printing area.This command justifies the space area according to HT, ESC .n 0Left justificationABCABCDABCDECenteringRight justificationABCABCDABCDEGS L nL nH[Name][Format][Range][Description]Set left marginASCII:GS L nL nHDecimal:29 76 nL nHHexadecimal:1D 4c nL nH0 nL 2550 nH 255Sets the left margin using nL and nH.The left margin is set to [(nL nH 256) 0.125 mm].ABCABCDABCDE
18/70CSN-A2 User manual [Note][Default]This command is effective only when processed at the beginning ofthe line in standard mode. If the setting exceeds the printable area, the maximum value of theprintable area is used.nL 0, nH 0ESC B n[Name][Format][Range]Set left blank char numbersASCII:ESC B nDecimal:Hexadecimal:Default is 00 m 4727 66 n1B 42 nESC nL ce]Set absolute print positionsASCII:ESC nL nHDecimal:27 36 nL nHHexadecimal:1B 24 nL nH0 nL 2550 nH 255Set the distance from the beginning of the line to the position at whichsubsequent are to be printed.The distance from the beginning of the line to the print position is[(nL nH 256) 0.125 mm] Settings outside the specified printable area are ignored. In standard mode, the horizontal motion unit (x) is used.ESC \, GS , GS \8.2.3 Character Setting CommandsESC ! n[Name][Format]Select print modeASCII:[Range][Description]Decimal:2733 nHexadecimal:1B21 n0 n 255Selects print mode(s) using n as racter Font A (12 24).
19/70CSN-A2 User manual1234567On011Character Font B (9 17).Off000Turn white/black reverse printing mode not selected.On022Turn white/black reverse printing mode selected.Off000Turn on/off upside-down printing mode not selected.On044Turn on/off upside-down printing mode selected.Off000Emphasized mode not selected.On088Emphasized mode selected.Off000Double-height mode not selected.On1016Double-height mode selected.Off000Double-width mode not selected.On2032Double-width mode selected.Off000Turn Deleteline mode on/off not selected.On4064Turn Deleteline mode on/off selected.---Undefined.GS ! n[Name][Format]Select character sizeASCII:[Range][Description]GS ! nDecimal:29 33 nHexadecimal:1D 21 n0 n 255(1 vertical number of times 8, 1 horizontal number of times 8)Selects the character height using bits 0 to 2 and selects the characterwidth using bits 4 to 7, as follows:BitOff/OnHexDecimalFunction0Character height selection. See Table 2.1234Character width selection. See Table 1.567Table 1Character Width SelectionTable 2Character Height )203230223304840334406450445
20/70CSN-A2 User manual5080605566096706677011280778[Note] [Default][Reference]This command is effective for all characters (alphanumeric andKanji), except for HRI characters.If n is outside the defined range, this command is ignored.In standard mode, the vertical direction is the paper feed direction,and the horizontal direction is perpendicular to the paper feeddirection. However, when character orientation changes in 90 clockwise-rotation mode, the relationship between vertical andhorizontal directions is reversed.When characters are enlarged with different sizes on one line, all thecharacters on the line are aligned at the baseline.The ESC ! command can also turn double-width and double-heightmodes on or off. However, the setting of the last received commandis effective.n 0ESC !GS B Turn white/black reverse printing modeASCII:GS B nDecimal:29 66 nHexadecimal:1D 42 n0 n 255Turns on or off white/black reverse printing mode. When the LSB of n is 0, white/black reverse mode is turned off. When the LSB of n is 1, white/black reverse mode is turned on. Only the lowest bit of n is valid. This command is available for built-in characters and user-definedcharacters. When white/black reverse printing mode is on, it also applies tocharacter spacing set by ESC SP. This command does not affect bit images, user-defined bit images,bar codes,HRI characters, and spacing skipped by HT, ESC . This command does not affect the space between lines. White/black reverse mode has a higher priority than underline mode.Even if underline mode is on, it is disabled (but not canceled) whenwhite/black reverse mode is selected.n 0
21/70CSN-A2 User manualESC V n[Name][Format][Range][Description]Turn 90 clockwise rotation mode on/offASCII:ESC V nDecimal:27 86 nHexadecimal:1B 56 n0 n 1, 48 n 49Turns 90 clockwise rotation mode on/off.n is used as follows:nFunction0,48Turns off 90 clockwise rotation mode1,49Turns on 90 clockwise rotation mode[Note] [Default][Reference]This command affects printing in standard mode. However, thesetting is always effective.When underline mode is turned on, the printer does not underline90 clockwise-rotated characters.Double-width and double-height commands in 90 rotation modeenlarge characters in the opposite directions from double-height anddouble- width commands in normal mode.n 0ESC !, ESCESC G [Reference]Turn on/off double-strike modeASCII:ESC G nDecimal:27 71 nHexadecimal:1B 47 n0 n 255Turns double-strike mode on or off. When the LSB of n is 0, double-strike mode is turned off. When the LSB of n is 1, double-strike mode is turned on. Only the lowest bit of n is enabled. Printer output is the same in double-strike mode and in emphasizedmode.n 0ESC E nESC E n[Name][Format]Turn emphasized mode on/offASCII:ESC E nDecimal:27 69 n
CSN-A2 User e]22/70Hexadecimal:1B 45 n0 n 255Turns emphasized mode on or off When the LSB of n is 0, emphasized mode is turned off. When the LSB of n is 1, emphasized mode is turned on. Only the least significant bit of n is enabled. This command and ESC ! turn on and off emphasized mode in thesame way. Be careful when this command is used with ESC !n 0ESC !ESC SP Set right-side character spacingASCII:ESC SP nDecimal:27 32 nHexadecimal:1B 20 n0 n 255Sets the character spacing for the right side of the character to [n 0.125mm (n 0.0049”)]. The right-side character spacing for double-width mode is twice thenormal value. When characters are enlarged, the right-side characterspacing is n times normal value. This command does not affect the setting of Kanji characters This command sets values independently in standard mode.n 0ESC SO n[Name][Format][Description]Select Double Width modeASCII:ESC SO nDecimal:27 14 nHexadecimal:1B 0E nSelect Double Width modeTo turn double width off, use LF or DC4 command.ESC DC4 n[Name][Format]Disable Double Width modeASCII:ESC DC4 n[Description]Decimal:27 20 nHexadecimal:1B 14 nDisable Double Width mode
CSN-A2 User manual23/70ESC { [Example]Turns on/off upside-down printing modeASCII:ESC { nDecimal:27 123 nHexadecimal:1B 7B n0 n 255Turns upside-down printing mode on or off. When the LSB of n is 0, upside-down printing mode is turned off. When the LSB of n is 1, upside-down printing mode is turned on. Only the lowest bit of n is valid. This command is enabled only when processed at the beginning of aline in standard mode. In upside-down printing mode, the printer rotates the line to beprinted by 180 and then prints it.n 0ESC - n[Name][Format]Turn underline mode on/offASCII:ESC - n[Range][Description]Decimal:27 45 nHexadecimal:1B 2D n0 n 2, 48 n 50Turns underline mode on or off, based on the following values n：nFunction0, 48Turns off underline mode1, 49Turns on underline mode (1 dot thick)2, 50Turns on underline mode (2 dots thick)[Note] The printer can underline all characters (including right-sidecharacter spacing), but cannot underline the space set by HT.
CSN-A2 User manual24/70 [Default][Reference]The printer cannot underline 90 clockwise rotated characters andwhite/black inverted characters. When underline mode is turned off by setting the value of n to 0 or48, the following data is not underlined, and the underline thicknessset before the mode is turned off does not change. The defaultunderline thickness is 1 dot. Changing the character size does not affect the current underlinethickness. Underline mode can also be turned on or off by using ESC !. Note,however, that the last received command is effective.n 0ESC !ESC % [Reference]Enable/Disable User-defined CharactersASCII:ESC % nDecimal:27 37 nHexadecimal:1B 25 n0 n 255Selects or cancels the user-defined character set. When the LSB of n is 0, the user-defined character set is canceled. When the LSB of n is 1, the user-defined character set is selected. When the user-defined character set is canceled, the built-incharacter set is automatically selected. n is available only for the least significant bit.n 0ESC &, ESC ?FS t Kanji character modeASCII:FS &Decimal:28 38Hexadecimal:1C 26Selects Kanji character modeFor Kanji model: When the Kanji character mode is selected, the printer processes allKanji code as two bytes each. Kanji codes are processed in the order of the first byte and secondbyte. Kanji character mode is not selected when the power is turned on.FS .
25/70CSN-A2 User manualFS.[Name][Format]Cancel Kanji character :28 46Hexadecimal:1C 2ECancels Kanji character mode.For Kanji model: When the Kanji character mode is not selected, all character codesare processed one byte at a time as ASCII code. Kanji character mode is not selected when the power is turned on.FS &FS ! n[Name][Format]Set print mode(s) for Kanji charactersASCII:FS !n[Range][Description]Decimal:28 33 nHexadecimal:1C21 n0 n 255Sets the print mode for Kanji characters, using n as ined.1－－－Undefined.2Off000Double-width mode is OFF.On044Double-width mode is ON.Off000Double-height mode is ��－－Undefined.7Off000Underline mode is OFF.On80128Underline mode is ON.3[Note] Double-height mode is ON.When both double-width and double-height modes are set (includingright- and left-side character spacing), quadruple-size characters areprinted.Th
CSN-A2 User manual 4/70 1 General Specifications 2 Features Low-noise direct thermal printing method Printer control panel built-in ANK character or GB18030 Chinese c
ČSN ISO 21940-12 . 011449 : Vibrace - Vyvažování rotorů - Část 12: Postupy . (ruší ČSN EN ISO 13850:2016) 211 Kč . 501556 . ČSN EN ISO 16993. 838225 . Tuhá biopaliva - Přepočet výsledků analýz pro různé stavy biopaliv (ruší ČSN EN ISO . 16993:2015) 211 Kč. 501529 . ČSN EN ISO 16994 .
5. To set the printer as the default, in the printer window, right-click on the printer, and then select Set as default printer. If successful, the printer is displayed with a green checkmark next to it. Your default printer has been set. Canon Printer To add a print code and set a Canon printer as your default printer: 1. Select the Windows .
504657 ČSN ISO 21940-2 011449 Vibrace - Vyvažování rotorů - Část 2: Slovník ruší ČSN ISO . na horská a závodní jízdní ruší ČSN EN ISO 4210-2:2016 kola 405 Kč . ruší ČSN EN 61000-4-12
Skoda Heavy Duty Live Centres - CSN 243324/CSN 243324M Features The rotating spindle is extended right through the tapered shank Two specially designed adjustable needle-roller bearings carry all radial loads A heavy duty ball thrust bearing takes all axial thrust Complete protection of bearings form the ingress of coolant,
Skoda Heavy Duty Live Centres - CSN 243324/CSN 243324M Features The rotating spindle is extended right through the tapered shank Two specially designed adjustable needle-roller bearings carry all radial loads A heavy duty ball thrust bearing takes all axial thrust Complete protection of bearings form the ingress of coolant,
To set up ReadySHARE Printer: Step 1: Connect the USB printer to the router’s USB port with a USB printer cable. Step 2: Install the USB printer driver software on each computer that will share the printer. If you do not have the printer driver, contact the printer manufacturer to find and download the most recent printer driver software.
Contains a brief overview of the printer. It contains information about the printer's features and what is included with the printer. Front View of Printer Contains a view of the front of the printer showing the location of the printer's consumable items. Printer Connections Shows all the connections to the printer: power, parallel .
Perfusionists certified by the American Board of Cardiovascular Perfusion through December 31, 2021. LAST FIRST CITY STATE COUNTRY Al-Marhoun Sarah New Orleans LA Alouidor Benjamin Los Angeles CA Alpert Bettina P. Marlborough MA Alpha Debra Reynolds Zionville IN Alshi Hanin Nooraldin H. Jeddah MA Saudi Arabia
