4P-4M-A2 Product Specification - CommScope
4P-4M-A24-port sector antenna, 4x 1695–2690 MHz, 65 HPBW.Uses the 4.3-10 connector which is 40 percent smaller than the 7-16 DIN connectorWith tilt indicators and integrated pluggable RETWind Loading: Frontal / Lateral / Rear – 346 / 94 / 436 N @ 150km/hConforms to RoHS 2011/65/EUGeneral SpecificationsAntenna TypeSectorBandSingle bandColorLight grayGrounding TypeRF connector body grounded to reflector and mounting bracketPerformance NoteOutdoor usageRadome MaterialPVC, UV resistantRadiator MaterialAluminumReflector MaterialAluminumRF Connector Interface4.3-10 FemaleRF Connector LocationBottomRF Connector Quantity, high band4RF Connector Quantity, total4Remote Electrical Tilt (RET) Information, GeneralRET HardwareRET-PMOD-A20-2RET Interface2x 8 pin connector as per IEC 60130-9 Daisy chain in: Male / Daisy chainout: Female Pin3: RS485A(AISG B), Pin5: RS485B(AISG A), Pin6: DC10 30V, Pin7: DC ReturnDimensionsWidth307 mm 12.087 inLength1377 mm 54.213 inDepth118 mm 4.646 inArray LayoutPage 1 of 5 2020 CommScope, Inc. All rights reserved. All trademarks identified by or are registered trademarks,respectively, of CommScope. All specifications are subject to change without notice. See www.commscope.com for themost current information. Revised: May 21, 2020
4P-4M-A2Port ConfigurationPage 2 of 5 2020 CommScope, Inc. All rights reserved. All trademarks identified by or are registered trademarks,respectively, of CommScope. All specifications are subject to change without notice. See www.commscope.com for themost current information. Revised: May 21, 2020
4P-4M-A2Electrical SpecificationsImpedance50 ohmOperating Frequency Band1695 – 2690 MHzPolarization 45 Total Input Power, maximum500 WRemote Electrical Tilt (RET) Information, ElectricalProtocol3GPP/AISG 2.0 (Single RET)Power Consumption, idle state, maximum2WPower Consumption, normal conditions, maximum10 WInput Voltage10–30 VdcInternal RETHigh band (2)Page 3 of 5 2020 CommScope, Inc. All rights reserved. All trademarks identified by or are registered trademarks,respectively, of CommScope. All specifications are subject to change without notice. See www.commscope.com for themost current information. Revised: May 21, 2020
4P-4M-A2Electrical SpecificationsFrequency Band, n, dBi17.818.218.518.3Beamwidth, Horizontal, degrees64626257Beamwidth, Vertical, degrees6.96.25.35.1Beam Tilt, degrees0–100–100–100–10USLS (First Lobe), dB20181817Front-to-Back Ratio, Copolarization180 30 , dB30292930Isolation, Cross Polarization, dB28282828Isolation, Inter-band, dB28282828VSWR Return loss, dB1.5 14.01.5 14.01.5 14.01.5 14.0PIM, 3rd Order, 2 x 20 W, dBc-150-150-150-150Input Power per Port, maximum,watts250250250250Electrical Specifications, BASTAFrequency Band, n by all Beam Tilts, average, dBi17.517.918.217.8Gain by all Beam Tilts Tolerance, dB 0.6 0.3 0.5 0.6Beamwidth, Horizontal Tolerance,degrees 3.7 2.5 2.7 3.2Beamwidth, Vertical Tolerance,degrees 0.6 0.5 0.3 0.3Front-to-Back Total Power at 180 30 , dB24262525CPR at Boresight, dB21242222CPR at Sector, dB111399Mechanical SpecificationsWind Speed, maximum241 km/h 149.75 mphPackaging and WeightsWidth, packed400 mm 15.748 inDepth, packed238 mm 9.37 inLength, packed1557 mm 61.299 inNet Weight, without mounting kit10.7 kg 23.589 lbPage 4 of 5 2020 CommScope, Inc. All rights reserved. All trademarks identified by or are registered trademarks,respectively, of CommScope. All specifications are subject to change without notice. See www.commscope.com for themost current information. Revised: May 21, 2020
4P-4M-A2Weight, gross16.2 kg 35.715 lbRegulatory pliant with the relevant CE product directivesCHINA-ROHSBelow maximum concentration valueISO 9001:2015Designed, manufactured and/or distributed under this quality management systemREACH-SVHCCompliant as per SVHC revision on cluded ProductsBSAMNTB95-01—Wide Profile Antenna Downtilt Mounting Kit for 2.4 - 4.5 in (60 - 115 mm) OD round members. Kit contains one scissortop bracket set and one bottom bracket set.* FootnotesPerformance NoteSevere environmental conditions may degrade optimum performancePage 5 of 5 2020 CommScope, Inc. All rights reserved. All trademarks identified by or are registered trademarks,respectively, of CommScope. All specifications are subject to change without notice. See www.commscope.com for themost current information. Revised: May 21, 2020
4P-4M-A2 2020 CommScope, Inc. All rights reserved. All trademarks identified by or are registered
Universal Serial Bus Revision 3.2 Specification Universal Serial Bus Revision 3.2 Specification. xxxx and xxxx xxxx and xxxx. Uni-versal Serial Bus Specification Universal Serial Bus Revision 3.2 Specification I2C-Bus Specification I2C-Bus Specification Sys-tem Management Bus Specification
HPKB Design Specification Document Data Mining Design Specification Document Non-Traditional Data Design Specification Document HMI Design Specification Document System Integration Design Specification Document 1.4. Software Design Specification Document Development Gui
Digital speed controller installation direction (left)*2 DR Digital speed controller installation direction (right)*2 G5 Designated grease specification NM Non-motor end specification PN PNP specification*1 TMD2 Split motor and controller power supply specification WA Battery-less absolute encoder specification WL Wireless communication specification WL2 Wireless axis operation specification
This specification is to be applied in conjunction with the supporting data sheet, quality requirements specification (QRS) and information requirements specification (IRS) as follows. IOGP S-740: Specification for Batteries (IEC) This specification
formal specification is an excellent way of discovering specification errors and presenting the system specification in an unambiguous way. . The Cleanroom method of software development (Prowell, et al., 1999), relies on formally based arguments that code conforms to its specification. Because
recognized industry standard API Specification 2C 7th Edition, 2012including Errata 2013, Offshore Pedestal-mounted Cranes, which is indispensable for the application of this specification. Following agreement of the relevant JIP33 work group and approval by the JIP33 Steering Committee, the IOGP Management Committee has agreed to the publicat ion of this specification by IOGP. Where adopted .
Specification Section 26 05 16 - Wire and Cable: 600 Volt and Below. 6. Specification Section 40 91 10 - Primary Elements and Transmitters. 7. Specification Section 40 97 00 - Control Auxiliaries. 8. Specification Section 40 98 00 - Control Panels and Enclosures. 9. Specification Section 40 99 00 - Surge Protection Devices (SPD) for Instrumentation
requirements specification, software requirements specification, software design specification, software test specification, software integration specification, etc. Requirements A requirement is a need, expectation, or obligation. It can be stated or implied by an
