CARTRIDGE VALVES / IN-LINE VALVES
CARTRIDGE VALVES / IN-LINE VALVESTechnical CatalogueJanuary2019web edition
Cartridge valves / In-line valves Section index iIndex and technical information .iPressure relief valves .1Sequence, pressure reducing and unloading valves .2Double cross relief valves .3One-way check valves.4Pilot check valves .5Manual and pneumatic operated valves .6End-off stroke valves.7Solenoid valves 2-way .8Solenoid valves 3-4 way .9Diverter valves .10Soft start valves .11Flow control valves .12Hand pumps .13Valve housings .14Cavities.15Standard plugs .16Coils.17Connectors .18 2018 Dana Brevini S.p.A. all rights reserved. Hydr-App, SAM Hydraulik, Aron, Brevini Hydraulics, BPE Electronics, VPS Brevini, OT Oiltechnology, logos aretrademarks or are registered trademarks of Dana Brevini S.p.A. or other companies Dana in Italy and other countries.The technical features supplied in this catalogue are non binding and no legal action can be taken against such material. Dana Brevini will not be held responsible for information and specifications which may lead to error or incorrect interpretations. Given the continuous technical research aimed at improved technicalfeatures of our products, Dana Brevini reserves the right to make change that are considered appropriate without any prior notice. This catalogue cannot bereproduced (in while or in part) without the prior written consent of Dana Brevini. This catalogue supersedes all previous ones.Use of the products in this catalogue must comply with the operating limits given in the technical specifications. The type of application and operating conditions must be assessed as normal or in malfunction in order to avoid endangering the safety of people and/or items.IE/NDX/003/2016TECHNICAL INFORMATION1
Cartridge valves / In-line valvesi1PRESSURE RELIEF VALVES (PAGE 13)CodeThreadFlow(l/min)Symbol DescriptionPagePCMP-HPVM14x1.55TDIRECT ACTING PRESSURE RELIEF VALVES(FOR HPV VALVES)14DIRECT ACTING PRESSURE RELIEF VALVES(FOR POWER PACKS SERIES MR/MW)15DIRECT ACTING PRESSURE RELIEF VALVES16DIRECT ACTING PRESSURE RELIEF VALVES17DIRECT ACTING PRESSURE RELIEF VALVES WITH ONEWAY CHECK VALVE18DIRECT ACTING PRESSURE RELIEF VALVES WITHLOGIC VALVE20DIRECT ACTING PRESSURE RELIEF VALVES WITH ONEWAY CHECK VALVE22DIRECT ACTING HIGH PRESSURE RELIEF VALVES WITHONE-WAY CHECK VALVE23DIRECT ACTING PRESSURE RELIEF VALVES24DIRECT ACTING PRESSURE RELIEF VALVES (FOR POWERPACKS SERIES MC/MS)25DIRECT ACTING PRESSURE RELIEF VALVES26DIRECT ACTING PRESSURE RELIEF VALVES27DIRECT ACTING PRESSURE RELIEF VALVES28PILOT OPERATED PRESSURE RELIEF VALVES29DIRECT ACTING PRESSURE RELIEF VALVESIN-LINE MOUNTING30DIRECT ACTING PRESSURE RELIEF VALVESIN-LINE MOUNTING31DIRECT ACTING PRESSURE RELIEF VALVESIN-LINE -16UNF30TCMPR04(serie 2)U13/4-16UNF30UTPPCPMK043/4-16UNF10CMPR04(serie 21/4” BSP30TPPPMVMP063/8” BSP50TPMVMP103/8” BSP40T2TECHNICAL INFORMATIONIE/NDX/003/2016
Cartridge valves / In-line valves1PRESSURE RELIEF VALVES (PAGE 13)CodeThreadFlow(l/min)SymbolDescription iPagePMVMP201/2” BSP80VALVOLE DI MASSIMA PRESSIONE AD AZIONE DIRETTAMONTAGGIO IN LINEA33VALVOLE DI MASSIMA PRESSIONE AD AZIONE PILOTATAMONTAGGIO IN LINEA34VALVOLE DI MASSIMA PRESSIONE AD AZIONE PILOTATAMONTAGGIO IN LINEA35TPMVMP303/4” BSP100TPVMP12BSP:3/4” - 1”P150T2SEQUENCE, PRESSURE REDUCING AND UNLOADING VALVES (PAGE onPage1CSQ04SEQUENCE VALVES - DIRECTLY OPERATED38SEQUENCE VALVES - DIRECTLY OPERATED(FOR MK3 SERIES POWER PACKS)39SEQUENCE VALVES - PILOT OPERATED40PRESSURE REDUCING VALVES WITH RELIEVING - DIRECTOPERATED41PRESSURE REDUCING VALVES WITH RELIEVING - PILOTOPERATED42SEQUENCE VALVES43PRESSURE REDUCING AND SEQUENCE VALVESIN-LINE MOUNTING4422CSMK043/4-16UNF101 /2” BSPCRC190MT3PPR TDOUBLE CROSS RELIEF VALVES (PAGE 45)CodeThreadFlow(l/min)SymbolA1VADILBSP:1/4” - 3/8”PageB1DOUBLE CROSS RELIEF VALVES DIRECT ACTINGIN-LINE MOUNTING30AIE/NDX/003/2016Description46BTECHNICAL INFORMATION3
Cartridge valves / In-line valvesi4ONE-WAY CHECK VALVES (PAGE ption211 PageONE-WAY CHECK VALVES48ONE-WAY CHECK VALVES49ONE-WAY CHECK VALVES50ONE-WAY CHECK VALVES51ONE-WAY CHECK VALVES(FOR POWER PACKS SERIES FP)52ONE-WAY CHECK VALVES53ONE-WAY CHECK VALVES54ONE-WAY CHECK VALVESIN-LINE MOUNTING55CHECK VALVES FOR PIPES56SHUTTLE VALVES58SHUTTLE VALVES59SHUTTLE VALVES60SHUTTLE VALVES61PUMP UNLOADING U067/8-14UNF60CRI043/4-16UNF202121TUPVR063/8” BSP30VUIBSP:1/4” - 3/8” - 1/2”20 - 50 - 80VRUBSP: 1/4” - 3/8”1/2” - 3/4 - 1”1” 1/4 - 1” 1/220 - 35 - 5080 - 140200 - 310VUBABSP: 1/4” - 3/8”1/2” - 3/44 - 6.316 - 25SH01M8x12U12121A1AAA1312SH021/8” BSP318231SH031/4” BSP522RVLV0M16x1.57RVLV1M27x1.5140311X24TECHNICAL INFORMATIONIE/NDX/003/2016
Cartridge valves / In-line valves5PILOT CHECK VALVES (PAGE 63)CodeThreadFlow(l/min)VRS1/4” BSPBSP: 1/4”-3/8”1/2”-3/4”12 - 3045 - 85VBPSA-VBPDABSP: 1/4” - 3/8”1/2” - 3/4”9/16-18 UNF20 - 2545 - 85BSP: 1/4” - 3/8”20 - AA1BB1AA1BB1A6 ABSINGLE ACTING PILOTED CHECK VALVES64SINGLE AND DOUBLE ACTING PILOT CHECK VALVES65SINGLE AND DOUBLE ACTING PILOT CHECK VALVES-DIN2353 PORTS67BMANUAL AND PNEUMATIC OPERATED VALVES (PAGE ption221115PageLEVER OPERATED VALVES70BUTTON OPERATED VALVES71PNEUMATIC OPERATED FF STROKE VALVES (PAGE 73)CodeThreadFlow(l/min)VFC3/8” BSP40X1SymbolDescriptionPageBAEND-OFF STROKE VALVESIN-LINE MOUNTING74DECELERATION VALVESIN-LINE MOUNTING75PYVD401/2” BSP40AIE/NDX/003/2016TECHNICAL INFORMATION5
Cartridge valves / In-line valvesi8SOLENOID VALVES 2-WAY (PAGE PILOTED OPERATED CARTRIDGE SOLENOID VALVEBIDIRECTIONAL78PILOTED OPERATED CARTRIDGE SOLENOID VALVEUNIDIRECTIONAL78HIGH PRESSURE PILOTED OPERATED CARTRIDGESOLENOID VALVE80VALVES IN ACCORDANCE WITH ATEX 94/9/CE DIRECTIVE82DIRECT OPERATED CARTRIDGE SOLENOID VALVE84CARTRIDGE SOLENOID VALVES 2 WAY 2 POSITIONS8623011CRP04XPage22CRB04 2211202CRD043/4-16UNF15 - 3013/4-16UNFC2V049221115SOLENOID VALVES 3-4 WAY (PAGE onPage2C3V0422SOLENOID VALVES 3-WAY/2-POSITION88SOLENOID VALVES 3-WAY/2-POSITION89SOLENOID VALVES 3 WAY 2 POSITIONS90SOLENOID VALVES 4 WAY 2 POSITIONS91SOLENOID VALVES 4 WAY 3 POSITIONS921 32C3V04273/4-16UNF201 3C3V03C4V0422*27/8-14UNF3/4-16UNF221 31 1S224S2631243131S124S1S231S1TECHNICAL INFORMATIONIE/NDX/003/2016
Cartridge valves / In-line valves 11 DIVERTER VALVES (PAGE 93)ThreadFlow(l/min)MR1/4” BSP1/4”BSPT—RBSBSP: 1/8” - 1/4”3/8”- 1/2” - 3/4”1” - 1”1/4 - 1”1/25 - 10 - 2540 - 100 - 150BK3BSP: 1/8” - 1/4”3/8” - 1/2” - 3/4”1” - 1”1/4 - 1”1/2CodeSymbolA B12PABPDDFBSP: 1/4” - 3/8”1/2” - 3/4 - 1”60 - 90120 - 20094HIGH PRESSURE - 2 WAY BALL VALVESIN-LINE MOUNTING95HIGH PRESSURE - 3 WAY BALL VALVESIN-LINE MOUNTING96DIVERTER VALVESIN-LINE MOUNTING97APA1PRESSURE GAUGE SHUT-OFFIN-LINE MOUNTING2PBiPageA B15 - 10 - 2570 - 100 - 150DescriptionPBA21BP212 SOFT START VALVES (PAGE 41/4” BSP20SINGLE-PHASE MOTOR START VALVEIN-LINE MOUNTING100SOFT START VALVEIN-LINE MOUNTING101TP0.2-0.5 barVAMS041/4” BSP80.4TIE/NDX/003/2016TECHNICAL INFORMATION7
Cartridge valves / In-line valves 13 FLOW CONTROL VALVES (PAGE 103)iCodeThreadFlow(l/min)SU/SBM10x1151/4” BSP20CSB043/4-16UNF40CSC043/4-16UNF291VSC041/4” BSP11,712VSC063/8” ageUNIDIRECTIONAL AND BIDIRECTIONAL FLOW REGULATORVALVES104FIXED UNIDIRECTIONAL FLOW CONTROL VALVE105BIDIRECTIONAL NOT COMPENSATED FLOW CONTROLVALVE106UNIDIRECTIONAL COMPENSATED FLOW CONTROL VALVE107FIXED PRESSURE COMPENSATED FLOW CONTROL VALVE108PRESSURE COMPENSATED FLOW CONTROL VALVES109PRIORITARY FLOW CONTROL VALVE110PRESSURE COMPENSATOR VALVE111TWO-WAY PRESSURE COMPENSATOR UPIPUPIXXVSR/VSBBSP: 1/4” - 3/8”1/2” - 3/4” - 1”15 - 3045 - 85 - 100AA1AA1SLEEVE FLOW CONTROL VALVES UNIDIRECTIONAL ANDBIDIRECTIONAL - IN-LINE MOUNTING113STU/STBBSP: 1/4” - 3/8”1/2” - 3/4” - 1”20 - 3050 - 85 - 150AA1AA1UNIDIRECTIONAL AND BIDIRECTIONAL FLOW REGULATORVALVES - IN-LINE MOUNTING1143/8” BSP29PRESSURE COMPENSATED FLOW UNIDIRECTIONAL FLOWREGULATOR VALVES - IN-LINE MOUNTING115STCA1A14 HAND PUMPS (PAGE 043/4-16UNF1cc - 2ccHAND PUMP11818TECHNICAL INFORMATIONIE/NDX/003/2016
Cartridge valves / In-line valvesVALVEPAGEBK3 . 96C2V04 . 86C3V03 . 90C3V0422 . 88C3V0427 . 89C4V0422*2 . 91C4V0422*3 . 92CCI06 . 111CCP20.112CMF04 . 70CMP02. 16CMP04. 17CMP06. 26CMP20. 28CMP30. 29CMP-HPV . 14CMPHR04. 23CMP-MC/MS . 25CMP-MR/MW . 15CMPR04 (serie 1) . 22CMPR04 (serie 2) . 18CP06 . 27CPE04 . 71CPM04.118CPMC04 . 24CPMK04 . 20CRB04 / CRP04 . 78CRC1 . 44CRD04 . 84CRD04P . 72CRF06 .110CRI04 . 52CRP04HP . 80CRP04X . 82CRU04 . 50CRU06 . 51CRU-MC/MS . 49CRU-MR . 48CSB04. 106CSC04. 107CSMK04 . 39CSQ04 . 38CVE06 . 43CVR06. 41CVR20. 42CVS20 . 40IE/NDX/003/2016VALVE PAGEDDF . 97MR . 94RBS. 95RVLV0 . 61RVLV1 . 62SH01 . 58SH02 . 59SH03 . 60STC .115STU/STB .114SU/SB . 104VADIL. 46VAM04 . 100VAMS04.101VBPSA-VBPDA. 65VBPSA-VBPDA DIN . 67VD40 . 75VFC .74VMP02 . 30VMP06 . 31VMP10 . 32VMP12 . 35VMP20 . 33VMP30 . 34VR06 . 53VRS . 64VRU . 55VSC04 . 108VSC06 . 109VSR/VSB .113VSU. 105VUBA . 56VUI . 54Section index . 1Technical information . 10Valve housings . 120Cavities . 124Standard plugs . 132Coils . 136Connectors . 142TECHNICAL INFORMATION9i
Technical informationINTRODUCTIONi OIL VISCOSITY ACCORDING TO TEMPERATURERead this instructions carefully before installation. All operations must becarried out by qualified personnel following the instructions. E1000The user must periodically inspect, based on the conditions of use and thesubstances used, the presence of corrosion, dirt, the state of wear and correctfunction of the valves.Always observe first the operating conditions given in datasheet ofthe 1001000800600704004030020020HYDRAULIC FLUID150100108640VG3042225VISCOSITY3Observe the recommendations given in the data sheet of the valve.The oilviscosity must be in the range of 10 mm²/s to 500 mm²/s.Recommended oil viscosity 46 mm2/s (32 mm2/s for Cartridge valves)ISOVGIS O V100IS O V G 6OG8VG 4632IS706050OISObserve the recommendations given in the data sheet of the valve. Use onlymineral oil (HL, HLP) according to DIN 51524. Use of other different fluids maydamage the good operation of the valve.2017151312111021.89Table 1: ISO viscosity grades7Kinematic-viscositylimitsmm²/s @ 40 CAveragekinematicviscositymm²/s @ 40 Cmin.max.ISO VG 10109.0011.0ISO VG 151513.516.5ISO VG 222219.824.2ISO VG 323228.835.2ISO VG 464641.450.6ISO VG 686861.274.8ISO VG 01.2-20 Values used in the chart “Oil viscosity according to temperature”-15 -10-50510015 207025 30401005013060140708090100200210 C110 FCONTAMINATIONOil contamination is the main cause of faults and malfunction in hydraulicsystems. Abrasive particles in the fluid erode or block moving parts, leadingto system malfunction.The valves we are offering do not require filtering characteristics any higherthan those needed for usual hydraulic components such as pumps, motors,etc.CONVERSION TABLE SSU / E / 4053035020SSU10504100Hydraulic fluid must also be cleaned properly before filling the hydraulic circuit, especially when commissioning a new system, as this is when the oilcontamination generally peaks due to its flushing effect on the components,and the running-in of the pump.Maximum contamination level is required on datasheet of the valve according to ISO 4406:1999.1003002002002010150400However, accurate filtering does guarantee reliability and a long life to all thesystem’s hydraulic parts. Reliable performance and long working life for alloil-pressure parts is assured by maintaining the level of fluid contaminationwithin the limits specified in the data sheet of the valve.1 E20100mm²/sIn the following table there is the correspondence between ISO 4406:1999and old standard NAS 1638 for information purpose:The standard ISO 4406:1999 defines the contamination level with three numbers that relate with the number of particles of average dimension equal orgreater than 4 μm, 6 μm e 14 μm, in 1 ml of fliuid.In following table there is a reference to reccomended contamination leveland correspondence with old NAS 1638 standard.TECHNICAL INFORMATIONIE/NDX/003/2016
Technical informationTable 2: Reccomanded contamination level.Oil filtration recommendationsCleanliness classAbsoluterecommendedfiltrationNAS 1638 micron ratingISO 4406 : 1999(*)( ** )Type of systemType of valveSystems or components operating atHIGH PRESSURE 250 bar (3600 psi)HIGH DUTY CYCLE APPLICATIONSSystems or components with LOWdirt toleranceSystems or components operating atMEDIUM / HIGH PRESSURESystems and components withmoderate dirt toleranceSystems or components operating atLOW PRESSURE 100 bar (1500 psi)LOW DUTY CYCLE APPLICATIONSSystems and components with GOODdirt tolerance18 / 16 / 137-8519 / 17 / 1491020 / 18 / 1510 - 1120* Contamination class NAS 1638: it is determined by counting the total particles ofdifferent size ranges contained in 100 ml of fluid.** Absolute filtration: it is a characteristic of each filter, it refers the size (in micron) ofthe largest sperical particle wich may pass through the filter.WORKING TEMPERATURESAmbient temperature range: -25 C to 60 CFluid temperature range (NBR seals): -25 C to 75 CThermal shocks can affect the performance and the expected life of the product, hence it is necessary to protect the product from these conditions.SEALSO-rings made in Acrylonitrile Butadiene (NBR) are normally fitted on thevalves. The backup rings that protect the O-rings are also made in NBR, orsometimes PTFE. Both the O-rings and the backup rings are suitable for theworking temperatures mentioned above.In the case of fluid temperatures 75 C, FKM seals must be used (identifiedwith “V1” variant).ELECTRICAL POWER SUPPLY nents in original-equipment quality.Before removing a coil, voltage must be disconnected.When replacing the coil, be aware to insert O-Rings in order to avoid theentrance of water.INSTALLATIONThe mounting surface must feature surface quality specified in data sheet ofthe valve: for example for Cetop valves generally is required Ra d 1.6μm andflatness d 0.03 mm over 100 mm length. Normally in cartridge valve for sealing diameters of the cavities, is required roughness Ra d 1.6μm. The surfacesand openings in the assembly plate must be free from impurity or dirt.Make sure the O-Rings fit correctly in their seats.Fixing screws must comply with the dimensions and the strength class specified in the data sheet and must be tightened at the specified tighteningtorque.Complete the electrical wiring. For circuit examples and pin assignments, seethe relevant datasheet.USE AND MAINTENANCEObserve the functional limits indicated in the technical catalogueOn a periodic basis and based on the conditions of use, check for cleanliness,state of wear or fractures and correct performance of the valve.If the O-rings are damaged, replace them with those supplied by the manufacturer.To assure the best working conditions at all time, check the oiland replace it periodically (after the first 100 working hours and then afterevery 2000 working hours or at least once every year).Attention: all installation and maintenance intervention must be performedby qualified staff.TRANSPORT AND STORAGEThe valve must be handled with care to avoid damage caused by impact,which could compromise its efficiency.In the case of storage, keep the valves in a dry place and protect against dustand corrosive substances.When storing for periods of more than 6 months, fill the valve with preservingoils and seal it.Solenoid valves coils are designed to operate safely in the voltage range of 10% of nominal voltage at max. 60 C ambient temperature. The combinationof permanent overvoltage and very hot temperatures can stress the solenoid.Therefore always a good heat dissipation and voltage level has to be assured.Faulty coils may only be replaced by new, interchangeable, tested compo-CONVERSION CHARTTypeSI unitsNewton(N) [kgm/s²]TorquemillimetermeterkilometerNewton meter(mm) [10 m](km) [1000 m](km) [1000 m](Nm)PowerkiloWatt (kW)[1000 Nm/s]PressureMegaPascal(MPa) [ N/mm²]Flow rateliter/min(l/min)TemperatureDegrees Celsius( C)ForceLengthIE/NDX/003/2016Alternative unitsKilogram forcepound forceinchyardmilepound force.feethorsepowermetric horsepowerbarpsi (lbf/ln²)ton/f/ln²UK gal/minUS gal/minFarenheitTECHNICAL INFORMATION(kgf)(lbf) [lbf/s²](in)(yd) [3ft](mile) [1760 yd](lbf.ft)(hp)(CV)( F)Conversion factor1 kgf 9.807 N1 lgf 4.448 N1 in 25.4 mm1 m 1.0936 yd1 mile 1.609 km1 lbf.ft 1.356 Nm1 kW 1.341 hp1 kW 1.36 CV1 MPa 10 bar1 MPa 145 psi1 ton/f/ln² 15.45 MPa1 UK gal/min 4.546 l/min1 US gal/min 3.785 l/min1 F 1.8 C 3211i
i12TECHNICAL INFORMATIONIE/NDX/003/2016
1PRESSURE RELIEF VALVESIE/C1/001/2011PRESSURE RELIEF VALVES13
CMP-HPVDIRECT ACTING PRESSURE RELIEF VALVES (FOR HPV VALVES)121.8 max3The direct acting relief valve limits the pressure in a hydraulic circuit to withinthe specified calibration range.It has a galvanised steel body. The tapered poppet is in tempered steel.39710616 18 Nmmax 5 Nm000120015 6 NmSpare seals kitHYDRAULIC SYMBOLPTORDERING CODEM10x1PM14x1.5Ø 17THYDRAULIC FEATURESMax. working pressure400 barMax. Flow5 l/minHydraulic fluidDIN 51524 Mineral oilsFluid viscosity10 500 mm2/sFluid temperature-25 C 75 CAmbient temperature-25 C 60 CMax. contamin. level class with filterISO 4406:1999 - class 19/17/14Weight0.038 kgTightening torquesee drawCavity (M14x1.5)CN032005 (See section 17)MIN.SETTING PRESSUREPRESSURE-FLOW RATE400CodeDescriptionRKVL1130002Direct acting relief 010505000123Q (l/min)450123Q (l/min)45Fluid used: mineral based oil with viscosity 46 mm²/s at 40 C.14PRESSURE RELIEF VALVESIE/CMP-HPV/001/2011
CMP-MR/MW DIRECT ACTING PRESSURE RELIEF VALVES (FOR POWER PACKS SERIES MR/MW)34 max1419The direct acting relief valve limits the pressure in a hydraulic circuit.It raises the safety level by making it impossible for the plant operators to seta higher pressure rating, than that specified in the catalogue. It has a packspring with a mechanical stop.It has a galvanised steel body. The guided ball poppet is in tempered andground steel.1PM15 x1AØ 12T31000012002HYDRAULIC FEATURES17Pressureidentificationmax 5 Nm16 19 NmSpare seals kitPHYDRAULIC SYMBOLTORDERING CODE220 barHydraulic fluidDIN 51524 Mineral oilsFluid viscosity10 500 mm2/sFluid temperature-25 C 75 CAmbient temperature-25 C 60 CMax. contamin. level class with filterISO 4406:1999 - class 19/17/1425 80 bar75 220 bar5 30 bar6 l/minWeight0.05 kgTightening torquesee drawCavity (M15x1)CN033001 (See section 17)The minimum permissible setting pressure depending on the spring: see curves below(see draw)SettingrangePressure increasing ateach turn of screw21000010.000A25 80 bar17 bar 10%21000011.000B75 220 bar45 bar 10%21000009.000C5 30 bar7 bar 10%IdentificationCodeMax. working pressureSetting range:Spring ASpring CSpring CMax. FlowPRESSURE-FLOW RATE75 220 bar5 30 bar367525030602002445P(bar)300P(bar)P(bar)25 80 bar9015018301001215506000123Q (l/min)4560123456Q (l/min)00123456Q (l/min)Fluid used: mineral based oil with viscosity 32 mm²/s at 50 C.IE/CMP MR-MW/001/2011PRESSURE RELIEF VALVES151
CMP02 DIRECT ACTING PRESSURE RELIEF VALVESThe direct acting relief valve limits the pressure in a hydraulic circuit.It raises the safety level by making it impossible for the plant operators to seta higher pressure rating, than that specified in the catalogue. This is limitedby a pack spring with a mechanical stop (only standard screw and nut), whichprevents temporary P closures caused by pressure peaks.It has a galvanised steel body. The guided ball poppet is in tempered andground steel.10 max 5 Nm1955 6 Nm13 18 NmPM10 x1CØ6.6Ø 22TM16 x1114.849.5 max30.8Ø 34.5HYDRAULIC FEATURESM48.5 maxQ25830021O-ring spare partPHYDRAULIC SYMBOLTPRESSURE-FLOW RATE4280260240220250 barHydraulic fluidDIN 51524 Mineral oilsFluid viscosity10 500 mm2/sFluid temperature-25 C 75 CAmbient temperature-25 C 60 CMax. contamin. level class with filterISO 4406:1999 - class 19/17/14Weight0.1 kgTightening torquesee drawCavity (M16x1)CN036001 (See section 17)max 30 barmax 90 barmax 180 barmax 250 bar20 l/minThe minimum permissible setting pressure depending on the spring: see curves SETTING PRESSUREMax. working pressureSetting range:Spring 1 (white)Spring 2 (yellow)Spring 3 (green)Spring 4 (orange)Max. Flow1008060402060502401302010000246810 12 14 16 18 20Q (l/min)0246810 12 14 16 18 20Q (l/min)1 CMP02C1. - 2 CMP02C2. - 3 CMP02C3. - 4 CMP02C4.Fluid used: mineral based oil with viscosity 46 mm²/s at 40 C.ORDERING CODECMPCMP Pressure relief valve02 M16 x 1C ScrewM Plastic knob1602****11 Serial RE RELIEF VALVES00 No variantsV1 Viton1 Max 30 bar (white spring)2 Max 90 bar (yellow spring)3 Max 180 bar (green spring)4 Max 250 bar (orange spring)IE/CMP02/002/2012
New!CMP04 DIRECT ACTING PRESSURE RELIEF VALVESThe direct acting relief valve limits the pressure in a hydraulic circuit.It raises the safety level by making it impossible for the plant operators to seta higher pressure rating, than that specified in the catalogue. It has a packspring with a mechanical stop.It has a galvanised steel body. The guided ball poppet is in tempered andground steel.82.352.3TØ 22C3Ø 7.225 30 NmØ 12.7243/4-16 UNF3025.936.53PHYDRAULIC FEATURES10max 5 Nm55.25Ø 26TPP55.25Ø 26TSP632max 0.5 NmMØ 35TPMax. working pressureSetting range:Spring 0 (white)Spring 1 (green)Spring 2 (yellow)Spring 3 (red)Max. Flow350 barHydraulic fluidDIN 51524 Mineral oilsFluid viscosity10 500 mm2/sFluid temperature-25 C 75 CAmbient temperature-25 C 60 CMax. contamin. level class with filterISO 4406:1999 - class 19/17/14Weight0.15 kgTightening torque25 30 NmCavity (3/4 - 16 UNF)CD018006 (See section 17)max 50 barmax 110 barmax 220 barmax 350 bar30 l/minThe minimum permissible s
SOLENOID VALVE VALVES IN ACCORDANCE WITH ATEX 94/9/CE DIRECTIVE DIRECT OPERATED CARTRIDGE SOLENOID VALVE CARTRIDGE SOLENOID VALVES 2 WAY 2 POSITIONS Code Thread Flow . STC 3/8” BSP 29 115 CPM04 3/4-16UNF 1cc - 2cc 118 2 1 2 3 1 TECHNICAL INFORMATION Cartridge va
Cartridge Valves Catalogue 2020 Content Page Preface Flyer Cartridge Valves Chapter 1 – Flow Preventing Check Valves 2 Pilot Actuated Check Valves 2-3 . position of a cylinder (e.g. outrigger cylinders) BH-Cartridge . BH Portfoliomanagment Cartridge Valves C
MANUAL VALVES PVC-U The PVC-U manual valves line consists of a comprehensive range of ball valves, butterfly valves, diaphragm valves, check valves, sediment strainers, air release valves, foot valves and angle seat valves for use in the construction of process and service lines fo
12. Hold the ink cartridge by its sides with the contacts toward the printer, insert the ink cartridge into its slot, and then gently push the ink cartridge until it snaps into place. 13. Repeat these steps to clean and reinsert the other ink cartridge. 14. Close the ink cartridge access door. 15.
Move the cartridge stem to the on position. The leak should stop draining out from around the cartridge stem. 3. Shut off the water supply. Remove the bonnet by turning it counterclockwise. Lift out the cartridge valve. Inspect the larger O-ring on the cartridge bonnet and the smaller O-ring on the cartridge stem. Remove any debris from the O .
Speichermedien - Band & Cartridge - RDX: HPE HPE RDX 4TB REMOVABLE DISK CARTRIDGE 1155950 Q2048A 456.00 HPE RDX 4TB USB EXT DISK BACKUP SYS IN 1155949 Q2R33A 579.00 Speichermedien - Band & Cartridge - RDX: Tandberg Data RDX 1TB INDUSTRIAL SSD CARTRIDGE (SINGLE) 1151621 8877-RDX 1519.00 RDX 2TB CARTRIDGE (SINGLE) 114058 8731-RDX 213.00
4 Section Pages Argus Atomac Automax Deutsche Audco Durco McCANNA 3-Piece Ball Valves 6 - 9 One Piece Threaded Valves 9 Flanged Ball Valves 10 - 14 One-Piece Butt Weld Valves 15 Top Entry Valves 15 Butterfly Valves 16 Non-lubricated Plug Valves 17 - 19 Lined Valves and Accessories 20 - 24 Check Valves 25 Gate Valves 25 Rotary Contro
FC & FL valves, WKM type valves, Shaffer type valves, Flocon type valves, check valves, cup testers, pulsation dampeners: www.mcmoiltools.com o’Drill / mCm Centrifugal pumps, cyclone pump, skid packages, gate valves, shear relief valves, reset relief valves, float valves, butterfly valves, plug
FSA ELA Reading Practice Test Questions Now answer Numbers 1 through 5. Base your answers on the passages “Beautiful as the Day” and “Pirate Story.” 1. Select the sentence from Passage 1 that supports the idea that the children are imaginative. A “‘Father says it was once,’ Anthea said; ‘he says there are shells there thousands of years old.’” (paragraph 2) B “Of course .
