Secure Seal - Security Chimneys
SSecure Seal Single-Wall, Double-Wall and Double-WallInsulated Special Gas Ventwww.securitychimneys.com800-361-4909 (US) 800-667-3387 (Canada)
Secure Seal SS, SSD, SSID,& FlexQUALITY AND DEPENDABILITYThe Secure Seal flue is manufactured from stainless steeldesigned for extreme resistance to chloride ion pitting,crevice corrosion and stress corrosion cracking, as wellas general corrosion in oxidizing and moderately reducingenvironments. AL29-4C is the standard choice, but alsoavailable in 316L, for withstanding the harmful effectsof corrosive condensates created by partially or fullycondensing high-efficiency natural gas and propane-firedheating appliances.The Canadian Gas Research Institute found that test resultsproved AL29-4C and 316L to be one of the two “mostcorrosion-resistant alloys of 20 candidate stainless steelsevaluated for resistance to chloride-induced corrosion incondensing and partially condensing gas-fired appliances.”STRINGENT STANDARDS FOR QUALITY ASSURANCETo guarantee a perfect fit every time and to avoid built-instress points or weak areas, tube ends are formed understringent guidelines and held to exacting standards.The casing (outer tube on Secure Seal SSD/SSID) ismanufactured from type 441 stainless steel to providelong-lasting performance and stability when exposed tothe outdoors.The air space between the flue and casing is 1” on SSDand 2” insulated on SSID, providing close clearances tocombustibles, reasonable outside dimensions and anadditional heat shield or margin of safety where needed.BUILT TO LASTSecure Seal features a smooth weld seam inside and out,which is completely shielded during the welding process.Contamination or molecular changes in the weld seam areavoided and no fillers are used in the welding process.The Secure Seal double-wall system is fully interchangeablewith our Secure Seal single-wall system. Both have beenconformed to UL1738 and certified to ULC-S636 safetystandards. When installed according to Security Chimneys’installation instructions, Secure Seal meets all testrequirements for horizontal and vertical, interior or exteriorinstallations. SSID features the same construction as SSD,but with 2” air space filled with mineral wool insulation.1 Security Chimneys www.securitychimneys.com
SECURITY CHIMNEYSSECURE SEALSINGLE WALL ANDDOUBLE WALLGAS VENTFeaturesBenefitsLaser butt-welding Reinforces strength Prevents leakage Increases durability and reliabilityBuilt-in Secure Lock system Provides quick and easy assembly and disassembly Requires less time on the job siteSecure Sealsealing gaskets S elf-sealing, so there’s no need to apply sealing material whenpieces are joined together Easier and faster installationStandard adjustable vent length P rovides vertical or horizontal adjustment for easysystem pitchingAL29-4C stainless steel standard or316L stainless steel alternative R esists the extreme corrosive environments found incondensing boilers Assures safe and trouble-free operationProven track record C onformed to UL1738 and certified to ULC-S636 T ype L: Listed to UL-641 and ULC-S609 (SSD/SSID) 15-year warrantyAll accessories made of stainless steel F or durability800-361-4909 (US) 800-667-3387 (Canada) 2
Secure Seal Single Wall (SS)Vertical InstallationEffective Length:When assembling two parts together,the joint will overlap 2-3/8”. So effectivelength is normal length minus 2-3/8”.Secure Seal Double Wall (SSD)Vertical Through-the-Roof InstallationSECURE SEAL SINGLE WALL (SS)Minimum Clearance to CombustiblesVertical Installation RequirementsDiameterRated operatingtemperatureMax flue Vertical1. The vent system must terminateat least 3 feet above the roof lineand at least 2 feet higher than anyportion of the building within 10 feet.This limitation can be removed if anengineering analysis demonstratesnormal and safe operation of appliance.3" to 12"480 F550 FN/AN/A2"2"14" to 24"480 F550 FN/AN/A4"4"2. When terminated at a height ofmore than 10 feet, the stack must besupported by a Guy Section.3. The vent system must terminate withone of the Secure Seal terminations.UnenclosedSECURE SEAL DOUBLE WALL (SSD/SSID)Minimum Clearance to CombustiblesDiameterRated operatingtemperatureMax flue HorizontalVertical3" to 12"480 F550 FN/A1"1"1"14" to 24"480 F550 FN/A1"3"1"3" to 12"(L-Vent)480 F570 FN/A2"2"2"14" to 24"(L-Vent)480 F570 FN/A2"3"2"Material ThicknessDiameterInner Wall Material ThicknessOuter Wall Material Thickness3" - 9"AL29-4C - .015"316L - .015”AL29-4C - .015"316L - .015”10" - 16"AL29-4C - .020"316L - .019”ALl29-4C - .020"316L - .019”18" - 24"AL29-4C - .024"316L - .024”AL29-4C - .024"316L - .024”3 Security Chimneys www.securitychimneys.com
PART NUMBERSThese instructions identify major modelSS-SSD-SSID parts by name and partnumber.Material Code DesignationsExample:SSD 36” length with inside diameter14” made of AL29-4C inner flue and SS441outer casting.SSD14L36UKModelDia.PartMaterialBType 316 Stainless SteelHType 430 Stainless SteelSS 30 elbow with inside diameter 22”KType 441 Stainless Steelmade of 316L.PType 439 Stainless SteelUType AL29-4C Stainless SteelSS22E30BModelDia.PartMaterialSSD wall support for 8” diameter chimney made of stainless 439.InstallationEach Secure Seal vent length and componentfeatures our Secure Lock system and Viton o-ringgasket, which insure a gas- and water-tight system.Parts are easily pushed and fastened togetherinstantly and effortlessly.Secure Seal can be taken apart and easilyreassembled, making inspection, maintenanceor rerouting of Secure Seal systems simpleand straightforward.Secure Seal provides an extensive range ofcomponents and accessories, made of stainlesssteel, allowing any type of installation. On top of thecommon components, we also offer special partsthat help simplify installation, such as the 2-degreeelbow and 43-degree tee (simplifying pitching ona horizontal vent) or the 18” and 36” adjustablelengths (to help maximize ease of installation).Connecting the SSD to a heater is effortless withone of the many adaptors approved by heatingappliance manufacturers. Heating equipmentcan be operated immediately upon completing aSecure Seal installation, as no cure time or cleanupis required.Note: If viton caulking is used at the boiler adaptoror an adjustable length, there is a cure time of24 hours.SSD8WSHDPModelDia.PartMaterialWhen venting Category I, II, III, or IV appliances or type L vented apliances,Secure Seal must be used for the entire length of the system. Do not mixpipe, fittings, or joining methods from different manufacturers. Everyvent system must be planned and installed for optimum performance andsafety. The venting system must be free to expand and contract and mustbe supported in accordance with these instructions. (Check for unrestrictedvent movement through walls, ceilings, and roof penetrations). Referto the gas appliance manufacturer’s instructions to determine ventingrequirements and limitations with respect to installation and use of theappliance. It is the responsibility of the installer to contact local buildingand fire officials concerning any installation restrictions and/or inspectionrequirements that may apply. Permits may be required before starting andinstallation. If required by the appliance manufacturer, a Drain Tee Cap must belocated as close as possible to the appliance flue outlet. Depending on thearrangement of the vent, more than one drain may be required. Unless aDrain Tee Cap is supplied with the appliance, install a Secure Seal DrainTee Cap. More than one Category II, III, or IV appliance may not be connectedinto the same vent system unless the appliance manufacturer specificallyapproved such a system and the appliance is designed for multiple venting. Secure Seal must not come in contact with plumbing orelectrical systems. Maintain rated clearances to combustibles over the entire length of thevent system. Secure Seal shall not be routed into, through, or within any vent, suchas an existing masonry or factory-built chimney that is connected toanother appliance.800-361-4909 (US) 800-667-3387 (Canada) 4
SSD & SSID Venting LengthsSSD & SSID LengthsUse to vent category II, III and IV appliances.ØEffective LengthProduct Code SSDProduct Code SSID3” to 24”6-5/8”SSDØL9SSIDØL93” to 24”9-5/8”SSDØL12SSIDØL123” to 24”15-5/8”SSDØL18SSIDØL183” to 24”21-5/8”SSDØL24SSIDØL243” to te: SSID 3”, 9” and 24” not available.SSD & SSID Adjustable LengthsUse to add length to straight length of Secure Seal pipe. Adds 2”–14”of length. Requires at least 4” overlap for a secure connection. Available inCustom Lengths.ØEffective LengthProduct Code SSDProduct Code SSID3” to 24”2” to 6-5/8”SSDØAL9SSIDØAL93” to 24”2” to 15-5/8”SSDØAL18SSIDØAL18EFFECTIVELENGTHØNote: SSID 3”, 9” and 24” not available.SSD & SSID Test Port LengthsUse to test for proper appliance operation without penetrating the ventwall. Easy access to perform flue gas analysis. Test port plug included.Effective LengthProduct Code SSDProduct Code SSID3” to e: SSID 3”, 9” and 24” not available.3 5/8”ØSSD & SSID Drain LengthsEffective LengthProduct Code SSDProduct Code SSIDK Factor3” to in plug not included.Drain Ø4–Ø10, 1/4 NPT, 1/2 O.DDrain 12–Ø24, 1/2 NPT, 5/8 O.DNote: SSID 3”, 9” and 24” not available.ØSSD & SSID Damper LengthsØEffective LengthProduct Code SSDProduct Code SSIDK Factor3” to 24”21-5/8”SSDØDAMPSSIDØDAMP0.60-9999PLATE FORACTUATOREFFECTIVELENGTHNote: SSID 3”, 9” and 24” not available.Ø5 Security Chimneys www.securitychimneys.com3 1/4”Ø
SSD & SSID Venting LengthsSSD & SSID Damper Lengths ShortØEffective LengthProduct Code SSDProduct Code SSIDK Factor3” to 24”6-5/8”SSDØDAMPSSSIDØDAMPS0 to 99996 5/8”4”Note: SSID 3”, 9” and 24” not available.Ø INT.SSD K&W Fixed Blade Damper LengthsØEffective LengthProduct Code SSD6” to 18”18”SSDØKWDAMP18"CSSD Motorized Damper LengthsØEffective LengthProduct Code SSD3” to 18”18”SSDØMOTDAMPNote: SSD 5”, 7”, 9”, 11”, 13”,15”, and 17” not available.18ØSSD & SSID Vent Flow RegulatorØEffective LengthProduct Code SSDProduct Code SSIDK Factor3” to 24”5-7/8”SSDØVFRSSIDØVFR0 to 99997 5/8”4 3/4”Ø INT.Note: SSID 3”, 9” and 24” not available.SSD Telescopic LengthsTelescopic lengths do not require cutting to fit dimension.ØEffective LengthProduct Code3” to 24”14” to 20”SSDØLAT203” to 24”20” to 32”SSDØLAT32EFFECTIVELENGTHMAXNote: SSID 3”, 9” and 24” not available.Ø800-361-4909 (US) 800-667-3387 (Canada) 6
SSD & SSID Venting ElbowsSSD 2-Degree ElbowOffsetRiseProduct Code SSDK Factor3” to 5”1/8”7-3/4”SSDØE2.046” to 8”1/8”7-7/8”SSDØE2.049” to 2.0316” to 18”1/8”8-1/4”SSDØE2.0320” to D24E2.03OFFSETRISEØ2ºUse to facilitate the 2 pitch required in horizontal runs. Offsets obstructions as needed.Allows for better condensate management and less back pressure.ØSSID 2-Degree ElbowOffsetRiseProduct Code SSIDK Factor1/8”7-3/4”SSIDØE2.046” to 8”1/8”7-7/8”SSIDØE2.0410” to 4E2.0416” to 18”1/8”8-1/4”SSIDØE2.0420” to 22”1/8”8-3/8”SSIDØE2.04RISEØ4” to 5”OFFSET2ºUse to facilitate the 2 pitch required in horizontal runs. Offsets obstructions as needed.Allows for better condensate management and less back pressure. 9” and 24” not available.ØSSD 15-Degree ElbowOffsets obstructions as needed. Allows for better condensate management and less backpressure.OffsetRiseProduct Code SSDK ”SSD24E15.267 Security Chimneys www.securitychimneys.comOFFSET15 ØRISEØ
SSD & SSID Venting ElbowsSSID 15-Degree ElbowOffsets obstructions as needed. Allows for better condensate management and less backpressure. 9” and 24” not available.ØOffsetRiseProduct Code SSIDK 50.2615 OFFSETRISEØSSD 30-Degree ElbowOffsets obstructions as needed. Allows for better condensate management and less backpressure.RiseProduct Code SSDK 800-361-4909 (US) 800-667-3387 (Canada) 8
SSD & SSID Venting ElbowsSSID 30-Degree ElbowOffsets obstructions as needed. Allows for better condensate management and less backpressure. 9” and 24” not available.RiseProduct Code SSIDK 2E300.51OFFSETRISEOffset30ºØØSSD 45-Degree ElbowOffsets obstructions as needed. Allows for better condensate management and less backpressure.RiseProduct Code SSDK Factor10-1/8”SSD3E45.304” to �SSD24E45.089 Security Chimneys www.securitychimneys.comOFFSETRISEOffset3-7/8”45 Ø3”Ø
SSD & SSID Venting ElbowsSSID 45-Degree ElbowOffsets obstructions as needed. Allows for better condensate management and less backpressure. 9” and 24” not available.RiseProduct Code SSIDK E450.08OFFSETRISEOffset45 ØØSSD 88-Degree ElbowUse to transition from a vertical to a horizontal run. Stabilizes a 2 pitch towards thecondensate drain for good condensate management.OffsetRiseProduct Code SSDK Factor3”8-3/8”9-1/4”SSD3E88.604” to 09 (US) 800-667-3387 (Canada) 10
SSD & SSID Venting ElbowsSSID 88-Degree ElbowUse to transition from a vertical to a horizontal run. Stabilizes a 2 pitch towards thecondensate drain for good condensate management. 9” and 24” not available.OffsetRiseProduct Code SSIDK Factor4” to �SSID22E88.21OFFSET88ºRISEØØSSD 90-Degree ElbowUse to go from horizontal to vertical runs or vertical to horizontal runs. Use to turn vent90 .OffsetRiseProduct Code SSDK Factor3”8-1/2”9-1/8”SSD3E90.604” to �27-1/2”28-1/8”SSD24E90.2011 Security Chimneys www.securitychimneys.comOFFSET90 ØRISEØ
SSD & SSID Venting ElbowsSSID 90-Degree ElbowUse to go from horizontal to vertical runs or vertical to horizontal runs. Use to turn vent90 . 9” and 24” not available.OffsetRiseProduct Code SSIDK /2”28-1/8”SSID22E900.21OFFSET90 RISEØØSSD & SSID Venting TeesSSD 43-Degree TeeUse in place of any tee for a 43 angle instead of 90 ; can be used as a manifold connectionto gang multiple boilers into a common vent.OffsetRiseProduct Code SSDK �Available with smaller snout and custom height.800-361-4909 (US) 800-667-3387 (Canada) 12
SSD & SSID Venting TeesSSID 43-Degree TeeUse in place of any tee for a 43 angle instead of 90 ; can be used as a manifold connectionto gang multiple boilers into a common vent. 9” and 24” not available.OffsetRiseProduct Code SSIDK SID22T430.4OFFSET43ºRISEHeightHEIGHTØØAvailable with smaller snout and custom height.SSD 45-Degree TeeUse in place of any tee for a 45 angle instead of 90 ; can be used as a manifold connectionto gang multiple boilers into a common vent.OffsetRiseProduct Code SSDK 3/4”SSD24T450.4Available with smaller snout and custom height.13 Security Chimneys www.securitychimneys.comOFFSET45 ØRISEHeightHEIGHTØ
SSD & SSID Venting TeesSSID 45-Degree TeeUse in place of any tee for a 45 angle instead of 90 ; can be used as a manifold connectionto gang multiple boilers into a common vent. 9” and 24” not available.OffsetRiseProduct Code SSIDK 2T450.4OFFSET45 RISEHeightHEIGHTØØAvailable with smaller snout and custom height.SSD 88-Degree TeeUse for a 88 offset, or to combine connections from two or more appliances into acommon vent. Can also use as a condensate management point when used in conjunctionwith drain fitting. All Standard Tees are completely welded.OffsetRiseProduct Code SSDK ��88ºØAvailable with smaller snout and custom height.800-361-4909 (US) 800-667-3387 (Canada) 14
SSD & SSID Venting TeesSSID 88-Degree TeeUse for a 88 offset, or to combine connections from two or more appliances into acommon vent. Can also use as a condensate management point when used in conjunctionwith drain fitting. All Standard Tees are completely welded. 9” and 24” not available.OffsetRiseProduct Code SSIDK HTØ88ºØAvailable with smaller snout and custom height.SSD 90-Degree TeeUse for a 90 offset, or to combine connections from two or more appliances into acommon vent. Can also use as a condensate management point when used in conjunctionwith drain fitting. All Standard Tees are completely welded.OffsetRiseProduct Code SSDK 2”SSD24T901.21Available with smaller snout and custom height.15 Security Chimneys ºØ
SSD & SSID Venting TeesSSID 90-Degree TeeUse for a 90 offset, or to combine connections from two or more appliances into acommon vent. Can also use as a condensate management point when used in conjunctionwith drain fitting. All Standard Tees are completely welded. 9” and 24” not available.OffsetRiseProduct Code SSIDK ØAvailable with smaller snout and custom height.SSD 90-Degree Tee YOffsetRiseProduct Code SSDK ��SSD4TY900.65” and 6”5-5/8”11-1/8”SSDØTY900.67” and 8”6-3/8”11-3/4”SSDØTY900.69” 2-1/2”SSD24TY900.6OFFSETRISEØØ45ºAvailable with smaller snout.800-361-4909 (US) 800-667-3387 (Canada) 16
SSD & SSID Venting TeesSSID 90-Degree Tee YØOffsetRiseProduct Code SSIDK Factor4”5-5/8”11-1/8”SSID4TY900.65” to 6”6-3/8”11-3/4”SSIDØTY900.67” to ��22-1/2”SSID22TY900.6RISEOFFSETØ45ºAvailable with smaller snout. 9” and 24” not available.SSD Lateral SecureTEEUse to transition from horizontal to vertical with improved flue gas flow.Product Code SSDK �SSD24BT0.55Available with smaller snout and custom height.17 Security Chimneys www.securitychimneys.comOFFSETRISERise4 to 8”OFFSETRISEOffsetHEIGHTHeightHEIGHTØ9 to 24”
SSD & SSID Venting TeesSSID Lateral SecureTEERiseProduct Code SSIDK SSID22BT0.554 to Use to transition from horizontal to vertical with improved flue gas flow. 9” and 24” notavailable.10 to 22”Available with smaller snout and custom height.SSD Lateral SecureTEE 88-DegreeUse to transition from horizontal to vertical with improved flue gas flow.Product Code SSDK 884 to 8”OFFSETRISEOffsetHEIGHTHeightHEIGHTغ889 to 24”Available with smaller snout and custom height.800-361-4909 (US) 800-667-3387 (Canada) 18
SSD & SSID Venting TeesSSD Lateral SecureTEE 88-DegreeRiseProduct Code SSIDK 884 to HEIGHTØ4”RISEOFFSETUse to transition from horizontal to vertical with improved flue gas flow. 9” and 24” notavailable.º8810 to 22”SSD Barometric TeeOffsetRiseProduct Code SSDK able with smaller snout and custom height.19 Security Chimneys ØØ
SSD & SSID Venting TeesSSID Barometric TeeOffsetRiseProduct Code SSIDK SSID22BMT0.2OFFSETRISEHeightHEIGHTØØAvailable with smaller snout and custom height. 9” and 24” not available.SSD & SSID Venting AccessoriesSSD & SSID Tee CapUse to cap Standard Tee, Branch Tee or Boot Tee. Remove Tee Cap to inspect the system;clean out debris or collected condensate.HeightProduct Code SSDProduct Code SSID3” to 24”4-1/8”SSDØTCSSIDØTC4 1/8”ØØNote: SSID 3”, 9” and 24” not available.SSD & SSID Drain Tee CapHeightProduct Code SSDProduct Code SSID3” to 24”4-1/8”SSDØDTCSSIDØDTCø4 1/8”ØDrain plug not included.Drain Ø4 – Ø10, 1/4 NPT, 1/2 0.DDrain Ø12 – Ø24, 3/8 NPT, 5/8 0.DNote: SSID 3”, 9” and 24” not available.DRAIN NPTSSD & SSID Barometric Tee CapØHeightProduct Code SSDProduct Code SSID3” to 24”3-1/2”SSDØBMTCSSIDØBMTC800-361-4909 (US) 800-667-3387 (Canada) 20
SSD & SSID Venting AccessoriesSSD & SSID Tapered IncreaserUse to increase vent diameter. Creates a smooth transition for an undisruptive flow.Available in custom size combinations.ØBAvailableHeightProduct Code SSDProduct CodeSSIDK Factor3” to 9”Ø 1”127/16”SSDØTIN(ØB)SSIDØTIN(ØB)0.054” to 22”Ø 2”137/16”SSDØTIN(ØB)SSIDØTIN(ØB)0.104” to 9”Ø 3”147/16”SSDØTIN(ØB)SSIDØTIN(ØB)0.154” to 20”Ø 4”157/16”SSDØTIN(ØB)SSIDØTIN(ØB)0.204” to 7”Ø 5”167/16”SSDØTIN(ØB)SSIDØTIN(ØB)0.254” to 18”Ø GHTØØNote: SSID 9” and 24” not available.SSD & SSID Step IncreaserØØBAvailableHeightProduct CodeSSDProduct CodeSSIDK Factor3” to 22”5” to 24”8”SSDØSIN(ØB)SSIDØSIN(ØB)KØ (1- 2)2KØB KØ/ 4 Ø/ØBØBHEIGHTUse to increase vent diameter when space c
Secure Seal shall not be routed into, through, or within any vent, such as an existing masonry or factory-built chimney that is connected to another appliance. Installation Each Secure Seal vent length and component features our Secure Lock system and Viton o
FASTSTACK CHIMNEYS FASTSTACK CHIMNEYS Faststack is a concept in chimney design suitable for both fully working and decorative functions. Faststack chimneys are easy to install saving both time and money on-site. The Faststack concept has been developed to make the installation of working and decorative chimneys simple and cost effective.
RS seal RS OMD seal RS PPS/S single-side seal RS PPS back-to-back seal Sleev-it Fire penetration seal Sleev-it Watertight penetration seal Sleev-it Transition collar R X seal RS X seal C RS T seal RG M63 seal CRL seal Wedge Stayplate C Wedge C Stayplate Lubricant Assembly Gel SE PPS extension frame GE extension frame Preholed entry plates
seal, manual shift valve 1.25 od 1: seal, oil pump 1: seal, front clutch piston 1: seal, front piston clutch 1: seal, rear piston clutch 1: filter, transmission governor 1: o-ring, trans oil filler tube 1: o-ring, sensor oil ring 1-1/16" id 2: seal, pump reaction shaft 1: seal, rear piston clutch 1: o-ring, kickdown servo 2: seal, accumulator 1 .
Visually inspect for irregularities in the shaft seal or an uneven alignment where the shaft seal contacts the motor. . VPH-SST-Fxxx Shaft Seal Back View of Shaft Seal (motor facing) Inside of Shaft Seal Lip VPS-SST-xxxx Shaft Seal MPS-SST-xxxx Shaft Seal. Rockwell Automation Publication 2090-IN012E-EN-P - February 2019 5
Confined Space. (secondary) NFPA 97, 2000 ed.; NFPA 211, 2000 ed. A space whose volume is less than 50 ft 3 /1000 Btu/hr (1.42 m /293 W) of the aggregate input rating of all appliances installed in that space. Draft. (preferred) NFPA 211, 2000 ed. The pressure differential that causes the flow of File Size: 345KBPage Count: 30Explore furtherNFPA 211: Standard for Chimneys, Fireplaces, Vents, and .www.nfpa.orgNFPA 211, Standard for Chimneys, Fireplaces, Vents, 2019 .blog.ansi.orgNFPA 211 & Your Chimney - Chimneys.comchimneys.comFree access NFPA codes and standardswww.nfpa.orgRecommended to you b
the chimney. Faststack Chimneys were the first products to meet the requirements of the CGMA. This provides third party performance testing developed with the assistance of the NHBC. All of our chimneys can be made using any brick, stone or render from your project for the best match The brick-clad Faststack Chimney System is a prefabricated
B Rubber bellows seal D O-ring seal, balanced M Metal bellows seal O Double seal, back-to-back P Double seal, tandem Q Seal with flush, quench seal W Double cartridge 2 rotating ring 3 stationary ring A Carbon, metal-impregnated B Carbon, synthetic resin-impregnated C Other types of carbon S
monitors, and flexible seating to accommodate small group, large group, and individual work. The classroom has a maximum capacity of 36 students. Figure 1 shows the classroom before and after redesign, and Figure 2 shows three views of the new ALC. Participants Faculty and students who had taught or taken at least one
