Walkerduct Pro Series - Construction
Walkerduct Pro SeriesRound Insert DuctsComplete Category 6, 5e & fiber capabilityin flush fittingsWiremold Walkerduct Pro Series Infloor Duct Systems provide fullcapability to install Category 6, 5e and Fiber Optic Cabling andConnections in a flush service fitting. The preset provides maximum cableperformance plus cable loop storage. Our flush service fittings alsoprovide the benefits of bend radius features at the workstation.The factory installed preset also makes it easy to feed conduit,partition feeds, and other feeds directly out of the preset. 2" [51mm] IPSpreset duct is also available for those applications where a flushactivation is not required.Flush service fittings are available in brass, brushed aluminum andnonmetallic finishes and can be fitted with modular communication inserts.Our pedestal service fittings, Multiplex Service Fittings and 525 SeriesFittings, can be used on either system. In addition, flushcarpet trim plates are available to make direct feeds out of the presets.Both styles of Walkerduct are UL Listed to U.S. and Canadian safetystandards. Walkerduct Pro Series is ideal for retail stores, schools,casinos, and office buildings.FIBER OPTIC CAT5Pro Series presets can be positioned togetherto create one activation location.F E AT U R E S & B E N E F I T Sn New brushed aluminum activations. Provides additionalfinish options for better aesthetics.n Heavy Duty Junction Box. Perfect for casino applications,heavy duty junction boxes are available for applicationswhere the duct system will be subjected to heavy loads.n Quality construction. Duct is made of 16 gauge galvannealedsteel with continuous seam weld construction. Makes for easyfield cuts and prevents water seepage into the duct.n Large bend radius into duct and around corners and elbows.Maintains integrity of fiber optic cable when changing directionof cable orientation.n Large oblong opening into duct. Allows easy hand accessinto the duct to pull wires. The opening provides enhancedbend radius when pulling cable.n One-meter fiber or cable loop storage in preset. Allowseasy access to cable to activate service fitting.n Flush activations for single-, double-, and triple-duct runsfor both tiled and carpeted floors. Aesthetically pleasingactivations in brass, brushed aluminum and nonmetallicprovide easy access to power and telecommunications ateach workstation. Activations accept Category 6, 5e, UTP,STP, coaxial, audio, and fiber optics inserts. Front loadedsnap-in inserts save installation time.n Only junction box available offering square or roundaccess cover plates. The flexibility to choose whichstyle will provide the greatest aesthetic appearancefor a particular tile or carpet application.n Built-in tile trim. The square junction boxes include flangelessaluminum trim to accommodate 1/8" [3.2mm] thick tile.Saves money.n Large preset. The preset has a large cubic inch capacityto allow easy access to wires and plenty of room forsplicing and connections. Saves installation time.IMPORTANT!A minimum 1 1/2" [38mm] preset or afterset is required on Pro Series Underfloor Duct to support standard duplex receptacles andcommunication devices when using flush activations. The 1" [25mm] preset or afterset should be specified for pedestalstyle fittings or when cabling will be pulled through the activation point.Presets have room tostore up to 1 meter ofcable in preset. Fiberloop clips (Cat. No.427) shown.Pro Series presetsoffer large accessarea into the duct.Flush activationsoffer a full rangeof power andcommunicationconnections.ED830 R11 – Updated February 2013 – For latest specs visit www.legrand.us/wiremold
Walkerduct Pro Series System LayoutsWALKERDUCT PRO SERIES SYSTEM LAYOUT WITH JUNCTION BOXESKEY42123456783582DuctPro Series PresetJunction BoxCouplingDuct SupportConduit AdapterElbowJunction Box Closure1516623477NOTE: Illustration is for showingproduct applications only.WALKERDUCT 2" [51MM] IPS DUCT SYSTEM LAYOUT WITH TRENCHDUCT3KEY2123456789101458109Trenchduct#2 2" IPS Duct#4 2" IPS DuctCross UnderCouplingsEnd ClosureSupportHorizontal Flat ElbowVertical ElbowBlank #4 DuctNOTE: Illustration is for showingproduct applications only.672
Adjustable Supports* SC12Hold-Down StrapHS12302CouplingsSC14HS14H302SC222HS222302Duct End Closures304H304304Conduit 24-Box CornerConduit AdapterTerminal Bushings255334UF255H334255334UFVertical Elbows332UFH332332UFHorizontal Elbows(90 & 45 )338UF342UFH338H342338UF342UFCrossunder Offsets372375H372H375372375Expansion Joints382H382382421422GR422RDBox Opening Closures 203421422GR422RDH203421422GR422RD203Box Closure 9H232-MudcapsMarker CapsSealantTile & CarpetTrim/HoldersJunction BoxConduct B17H232SC3222- SC3224HS3222 resquareFT15FT18FT15FT18roundroundSFCS14- SFCS17SFCB14- SFCB17212212232232H2323444 System3424 System3244 System3224 System3222 System244System224System222System14 SystemAccessories12 SystemWalkerduct Pro Series Systems reFT25FT25roundSFCS24SFCB24H232* Supports include built-in Coupling.NOTE: Part numbers ending in a dash need to have the height adjustment size suffix included whenordering. Please see the individual support product descriptions for this information.Walkerduct Duct Systems provide wire management foropen space environments while maintaining aestheticsbecause they are buried in the floor, out of sight, andsafe from abuse. The duct is designed to be used withWalkerduct Junction Boxes or Trenchduct to create aninfloor wire management system. Duct runs provide arange of capacities to suit any situation and to futureproof the wire management system. Duct can be used6"12"individually or combined with other duct to deliver[152mm] [305mm]power and communication services to workstations.Multiple duct runs may be all one size of duct or a mixof sizes. Activations may be located anywhere alongthe length of the duct to maximize flexibility andaccessibility to wiring workstations. Flexibility is onlylimited by the grid pattern. Walkerduct Duct Systems aredesigned to be used with power and communications12"[305mm]service fittings. Refer to the Service Fittings section ofthe Product Guide or the individual productspecifications for more m] 0mm]24"[610mm]10'[3m]
Walkerduct Pro Series Ordering Informationj Catalog No. /Item2-04-0Description/Specifications3 1/8" x 1 1/4"[79mm x 32mm]No. 2 DuctNo. 4 Duct2-04-06 1/2" x 1 1/2"[165mm x 38mm]3.34 Sq. In. ng,spacing,spacing,1" presets.1 1/2" presets.2 " presets.2 1/2" presets.3" presets.1" presets.1 1/2" presets.2" presets.2 1/2" presets.3" g,spacing,spacing,1" presets.1 1/2" presets.2" presets.2 1/2" presets.3" presets.1" presets.1 1/2" presets.2" presets.2 1/2" presets.3" presets.8.72 Sq. In. [56.3cm2]No. 2 Duct with 12"[305mm] SpacingNo. 4 Duct with 24"[610mm] SpacingEnd View with Alignment Clip in PlaceAlignment ClipCatalog Numbering System:Example:D21215DuctSize of DuctPreset HeightPreset SpacingBlank Duct – Used primarily forfeeder runs. 10' [3m] standardlength. One-piece continuousseam weld construction.16 gauge [1.5mm]galvannealed steel.Preset Duct – Used for distributionruns. 10' [3m] standard length.One-piece continuous seam weldconstruction. 16 gauge galvannealedsteel. Die-cast presets haveknockout in base. With knockoutremoved, the opening size intoduct is 3 1/8" x 1 5/8" [79mm x 41mm].No. 4 duct is punched off center.An alignment clip is included witheach piece of duct. This is usedto connect presets and preventmovement of presets duringconcrete pour.Standard preset spacings are12" [305mm] and 24" [610mm]on center. Preset heights are:1" [25mm], 1 1/2" [38mm], 2"[51mm], 2 1/2" [64mm], and3" [76mm]. Presets are sealedwith recessed removable mudcap.Preset dimensions are 4 1/8" widex 4 13/16" long [105mm x 123mm].IMPORTANT!IMPORTANT!Triple-gang flush activations are notcompatible with 3244 and 3444System layouts. Use combination ofsingle- and two-gang activations toaccess all three ducts at one point.A minimum 1 1/2" [38mm] preset or afterset is required on ProSeries Underfloor Duct to support standard duplex receptaclesand communication devices when using flush activations. The1" [25mm] preset or afterset should be specified for pedestal stylefittings or when cabling will be pulled through the activation point.421Mudcap – Steel replacementcap for preset. Recessed tohold 3/8" [9.5mm] concrete.422GR422RD(Green)(Red)Marker Cap – Replaces mudcapon preset to indicate location ofthe last insert in each run. Selectcolor for each service.425 1/2"426 1"[12.1mm] High[25mm] HighPreset Extensions – Can befactory or field installed toincrease height of presets. Die-castconstruction. Attaches with push onmetal sleeves (included). 1" [25mm]size can be stacked. 1/2" [12.7mm]size cannot be stacked with anotherextension on top.D2075D4075For No. 2 DuctFor No. 4 DuctDuct Conduit Hub (12" [305mm]Section of Duct with 1" [25mm]Preset) – For rigid or PVC conduit.Used to provide feed to isolatedoutlets; maintains 24" [610mm]spacing of presets. Preset heightis 1" [25mm]. Add extensions ifhigher preset needed.4
Walkerduct Underfloor Duct Ordering InformationCatalog No. cing,spacing,spacing,spacing,7/8" presets.1 1/2" presets.2" presets.2 1/2" presets.3" presets.Preset Duct – Used for distribution runs. 10'[3m] standard length. One-piece continuousseam weld construction. 16 gauge galvannealedsteel. Round die-cast presets have insidethreads to accept standard ,spacing,7/8" presets.1 1/2" presets.2" presets.2 1/2" presets.3" presets.Standard preset spacings are 12" [305mm] and24" [610mm] on center. Preset heights are 7/8"1 1/2", 2", 2 1/2" and 3" [22.2mm, 38mm, 51mm,64mm and 76mm]. Presets are sealed withrecessed removable mudcap. Preset insidediameter is 2" cing,7/8" presets.1 1/2" presets.2" presets.2 1/2" presets.3" presets.Service fitting selections for 2" [51mm] IPSpreset duct are: 525 Series, Multiplex, and1200 ,spacing,Cable Size/Wire Fill Chart7/8" presets.1 1/2" presets.2" presets.2 1/2" presets.3" presets.O.D.Catalog Numbering System:Example:2-24 x 2 x 2DuctPreset SpacingAREA (SQ IN)CABLE/WIRE SIZEPreset Height2" [51mm] IPSNo. 2 Duct with 12"[305mm] SpacingInches[mm]InchesUNSHIELDED TWISTED PAIR4-PAIR, 24 AWG CAT 54-PAIR, 24 AWG CAT EPHONE2-PAIR, 24 AWG4-PAIR, 24 AWG25-PAIR, 24 36.8]4429231167561SHIELDED TWISTED PAIRTYPE 1TYPE 2TYPE 9.7][30.3]11728292074FIBER OPTIC2-STRAND4-STRAND6-STRANDFIBER 56842THHN WIRE#14#12#10# 8# 6# 4No. 4 Duct with 24"[610mm] Spacing[mm]40% FILL*NO. 2NO. 4DUCT DUCT*40% cable fill is the maximum cable allowed by NEC.404Mudcap – Steel replacement cap for 2"[51mm] IPS preset. Recessed to hold 3/8"[9.5mm] For No. 2 DuctFor No. 4 DuctMarker Cap – Replaces mudcap on preset toindicate location of run. NEC requires markersto locate the last preset in each run. Select colorfor each service.2' [610mm] Section of Duct with IPS Presetand 3/4" [19.1mm] Conduit Hub – For rigid orPVC conduit. Used to provide feed to isolatedoutlets; maintains 24" [610mm] spacing ofpresets. Heights from 7/8" [22.2mm] to3 1/2" [89mm]. *Specify preset height.12"[30mm]24"[610mm]5
Duct Supports Ordering InformationCatalog C3424Description/SpecificationsFor one No. 2 DuctFor one No. 4 DuctFor two No. 2 DuctsFor one No. 2 Ductand one No. 4 DuctFor two No. 4 DuctsFor three No. 2 DuctsFor two No. 2 Ductsand one No. 4 DuctFor one No. 2 Ductand two No. 4 DuctsFor two No. 4 Ductsand one No. 2 Duct(No. 2 Duct in center)Adjustable Duct Supports with Built-InCouplings – To support, couple, and holdduct in place before and during concretepour. Steel construction. Leveling screwsprovide vertical adjustment. Differentleg heights available. Supports maybe fastened to form or to slab throughholes in the feet. Top membersmaintain 1" [25mm] spacing betweenducts. Locate duct supports onapproximately 5' [1.5m] intervals.ESC14EHow to Determine CorrectSupport HeightsSC222ACat No.DIMENSION 1.500[292mm]SC22212.250[311mm]BHeight of duct.SC22415.625[396mm]CSC24419.000[482mm]Distance from bottom of duct toform or slab. This dimension isthe correct support 4219.750[501mm]Distance between finished concretefloor line and floor slab. Thisdimension is the sum total ofA, B, and C.SC324423.125[587mm]Support Height (C) D - (A and *Cat. No. SuffixHeight Adjustment-181/2" [12.7mm] to 1 7/8" [48mm]-331 1/2" [38mm] to 3 3/4" [95mm]-483" [76mm] to 4 7/8" [124mm]Duct supports for deeper pours are available throughthe factory.NOTE: Recommend minimum of 3" [76mm]clearance space on each sideof duct support (E dimension)for concrete placement.Catalog Numbering System:Example:SC3244SupportNo. of Ductsin SystemHeight of preset.Duct Sizeand OrientationHold-Down Straps Ordering InformationCatalog S3424Description/SpecificationsFor one No. 2 DuctFor one No. 4 DuctFor two No. 2 DuctsFor one No. 2 Ductand one No. 4 DuctFor two No. 4 DuctsFor three No. 2 DuctsFor two No. 2 Ductsand one No. 4 DuctFor one No. 2 Ductand two No. 4 DuctsFor two No. 4 Ducts withone No. 2 Duct in centerHS32241"[25mm]1 5/8"[41mm]Hold-Down Straps – To fasten ductsto the slab in shallow concrete. Usedin place of duct supports. Strapsmaintain 1" [25mm] spacingbetween ducts on multiple ductruns and prevent duct from floatingduring concrete pour. Attaches toslab with stakes or drive pins (notincluded). Locate hold-down strapson approximate 5' [1.5m] centers.Two Holes 9/32"[7.1mm] Dia.EHS143/4"[19.1mm]ITEMHS12“E” DIMENSION5 3/16"[132mm]HS148 1/16"[205mm]HS22210 5/8"[270mm]HS22414"[356mm]HS24417 3/8"[448mm]HS322214 13/16"[376mm]HS322418 3/16"[462mm]HS324421 9/16"[548mm]HS342421 9/16"[548mm]6No. 2 Duct strap is 1 1/4" H [32mm]; No.4 Duct strap is 1 1/2" H [38mm]; Strapshave a maximum width of 1 1/4" [32mm].
Duct Closures, Elbows and Offsets Ordering InformationCatalog No./ItemDescription/SpecificationsCatalog No./ItemDescription/Specifications304Duct End Plug – To sealend of No. 2 Duct.A 3 1/8" [79mm];B 1 1/4" [32mm].H33890 Horizontal Elbow –Creates 90 horizontalturn in No. 4 Duct.H304Duct End Plug – To sealend of No. 4 Duct.A 6 1/2" [165mm];B 1 1/2" [38mm].AB302BH30210 1/2"[267mm]10 1/2"[267mm]2 13/16" R[71mm]H338AU-1Coupling – To couple twoNo. 2 Ducts.A 3 1/4" [83mm];B 1 3/8" [38mm].90 Horizontal Elbow withAccess Unit – Used to make90 horizontal turn in No. 4Duct. Access cover can beremoved to facilitate wirepulling. For concrete poursover 1" [25mm] an extensionring is required. See Cat. No.6AER- rings on page 9.5 3/4" D[146mm]Coupling – To couple twoNo. 4 Ducts.A 6 9/16" [167mm];B 1 9/16" [40mm].A10 1/2"[267mm]10 1/2"[267mm]2 13/16" R[71mm]334UFPanel Connector – SecuresNo. 2 Duct to cabinet.2 3/4"[70mm]342UFAdjustable Horizontal Elbow –No. 2 Duct elbow angled for45 turn. Angle may be variedfrom 22 1/2 to 67 1/2 bycutting duct ends atdifferent angles.4 1/8"[105mm]H3345"[127mm]Panel Connector – SecuresNo. 4 Duct to cabinet.7/8"[22.2mm]3" R[76mm]45 Min. OffsetH3423 5/16"[84mm]7 11/16"[195mm]332UF2 5/16" R[59mm]5 1/8"[130mm]90 Vertical Elbow – Creates90 vertical turn inNo. 2 Duct.5 1/2"[140mm]Min. Offset45 3" R[76mm]372 For No. 2 DuctH372 For No. 4 Duct5 1/8"[130mm]H3323" R[76mm]Adjustable Horizontal Elbow –No. 4 Duct elbow angled for45 turn. Angle may bevaried from 22 1/2 to67 1/2 by cuttingduct ends atdifferent angles.90 Vertical Elbow – Creates90 vertical turn inNo. 4 Duct.Offset – Used to raise orlower a run of duct by 1 5/8"[41mm]. Two required forcrossunders. Used withfield-cut blank duct.8 1/2"[216mm]3 7/16"[87mm]8 1/2"[216mm]338UF21 7/8"[556mm]21 7/8"[556mm]90 Horizontal Elbow –Creates 90 horizontalturn in No. 2 Duct.1 5/8"[41mm]6 3/8"[162mm]8 1/2" R[216mm]7
Duct Closures, Elbows and Offsets Ordering Information (Continued)Catalog No./ItemDescription/SpecificationsCatalog No./ItemDescription/Specifications375 For No. 2 DuctH375 For No. 4 DuctVariable Offset – Usedto raise or lower a run ofduct from 5/16" [7.9mm]to 3 1/2" [89mm]. Fieldcut duct based onchart below.300-4Adapter Coupling – CouplesNo. 2 Duct to No. 4 Duct.6"[152mm]3 9/16"[90mm]10 7/8"1/4"5/8"5"Expansion Joint Sleeves –Slip over two sections ofduct. Outside screws fastenand ground sleeves to duct.Amount of expansion isdetermined by gap allowedbetween duct sections.5/8"[15.9mm]DUCT 15.9mm][17.5mm][19.1mm][20.6mm][22.2mm][23.8mm]382 For No. 2 DuctH382 For No. 4 DuctDuct5/8"[15.9mm]6 m][83mm][89mm][98mm][108mm][118mm][127mm]1"1 1/4"1 1/2"1 3/4"2"2 1/4"2 1/2"2 3/4"3"3 1/4"3 m][76mm][83mm][89mm]DUCT CUT(LENGTH)5 3/8"6 13/16"8 1/4"9 11/16"11 1/4"12 9/16"14"15 7/16"16 7/8"18 5/16"19 t Conduit Adapters Ordering InformationCatalog No./ItemDescription/SpecificationsCatalog No./ItemDescription/Specifications312-3/4 le Conduit Adapter –Fits on outside of No. 2Duct. For one rigid orPVC conduit.324-3/4Male Conduit Adapter –Fits into end of No. 2 Duct.For two 3/4" trade sizerigid or PVC conduits.314-3/43"[76mm]3"[76mm]1 1/8"[29mm]3 1/2"[89mm]H312-3/4 [19.1mm]-1[25mm]-11/4 [32mm]-11/2 [38mm]-2[51mm]Male Conduit Adapter –Fits into end of No. 2 Duct.For one 3/4" trade sizerigid or PVC conduit.7"[178mm]3 1/2"[89mm]Female Conduit Adapter –Fits on outside of No. 4Duct. For one rigid or PVCconduit. H322-11/2 withone opening plugged isused for H312-11/2.1 3/4"[44mm]2 1/8"[54mm]H322-1-11/4-11/2-21 1/4"[32mm]322-11/4-11/2[32mm][38mm]Female Conduit Adapter –Fits on outside of No. 2Duct. For two rigid or PVCconduits. Suffix indicatesconduit trade size.[25mm][32mm][38mm][51mm]7 1/8"[181mm]3 1/2"[89mm]3"[76mm]8Note: For H312-2 this dimensionis 2 1/2" [64mm].Female Conduit Adapter –Fits on outside of No. 4Duct. For two rigid or PVCconduits. Suffix indicatesconduit trade size.
Aftersets Ordering InformationCatalog No./Item421042154220422542301"1 1/2"2"2 ecificationshighhighhighhighhighAfterset – Installed either before or after concrete pour to createactivation from duct. Requires 6 1/2" [165mm] core drilled hole inconcrete and 2 1/2" [64mm] diameter hole in duct. Requires grout fillaround afterset to fill voids in 6 1/2" [165mm] hole. Attaches to duct withlocking tabs. Extensions can be attached to increase height. Aftersetsare gangable. Alignment clip and mudcap included. All Pro Seriesactivations fit on afterset. See ED850 and ED667.IMPORTANT!4 13/16"[123mm]436-2-7/8-2-1 1/2-2-2-2-2-2 3/8-2-37/8" [22.2mm]1 1/2" [38mm]2"[51mm]2 3/8" [64mm]3"[76mm]4 1/8"[105mm]highhighhighhighhighA minimum 1 1/2" [38mm] preset or afterset is required on Pro Series UnderfloorDuct to support standard duplex receptacles and communication devices when usingflush activations. The 1" [25mm] preset or afterset should be specified for pedestalstyle fittings or when cabling will be pulled through the activation point.Round Afterset – Installed either before or after concrete pourto create activation from duct. Requires 2 1/2" [64mm] coredrilled hole in concrete and 2 1/4" [57mm] diameter hole in duct.Attaches to duct with locking tabs. Extensions can be attachedto increase height.Walkerduct Junction Boxes Ordering InformationPurpose:Square Cover PlateRound Cover PlateJunction boxes are used at intersections of duct runs to:1. To separate the various raceways as they cross each other.2. To furnish access to the system for pulling and splicing of wires.3. To provide means of connecting the system to distribution closetswith duct or conduit home runs.Construction Features:Aluminum TrimOpenings are provided in the four sides to receive from one to five ducts, whichare secured by grounding clips. Corner openings provide conduit feeds.The interiorsof the boxes have partitions which completely separate each duct and at the sametime form a continuous path through the box in both directions. No partitions are neededfor single run boxes. Most partitions are removable and their orientation can be changedto correct installation errors. For precise leveling after the pour, cover plates can beadjusted upward 1/2" [12.7mm] with the recessed screws in the cover plate.Standard boxes are designed for use with duct having 1" [25mm] high presets. Boxes with higher side railsin 1/2" [12.7mm] increments can be furnished for systems requiring higher presets. Cover plates are1/4" [6.4mm] thick. Junction boxes are provided with nonmetallic corner inserts to provide controlledcable bend radius around the tunneling inside the box (see diagram). They should be snapped intoplace before wire placement. Brass or stainless steel holders for tile and carpet can be used on topof the round cover plates. Square junction boxes include aluminum trim for carpet or tile applications.Cable BendControl InsertsHeavy duty junction boxes are used where heavy loads will be rolled over or placed on the system. These are constructed with a 3/8" [9.5mm]cover plate and additional support studs. Up to 5/8" [15.9mm] concrete recommended over presets for heavy loads. Minimum heavy dutyjunction box height is 1 1/2" [38mm].ItemCatalog No./Description/Specifications12JS-* (square cover plate)12JR-* (round cover plate)7"[178mm]12HS-* Heavy duty (square)12HR-* Heavy duty (round)*SUFFIX FOR JUNCTION BOXES15/16" [23.8mm]1 5/8"[41mm]6 3/4"[172mm]11 3/8"[289mm]2 9/16"[65mm]Junction Box – One No. 2 Duct perside. No interior partitioning. Squarecover plate measures 6 3/4" x 6 3/4"[171mm x 171mm]. Diameter ofround cover plate is 4.813" [122mm].Specify suffix.DEPTH OF CONCRETE OVER DUCT11"[25mm] min. to 1 1/2" [35mm]1 1/21 1/2" [38mm] min. to 2"[51mm]22"[51mm] min. to 2 1/2" [62mm]2 1/22 1/2" [64mm] min. to 3"[76mm]33"[76mm] min. to 3 1/2" [89mm]3 1/23 1/2" [89mm] min. to 4"[102mm]*Other junction box heights are available. Consult factory for availability.9max.max.max.max.max.max.
Walkerduct Junction Boxes Ordering Information (Continued)ItemCatalog No./Description/Specification14JS-* (square cover plate)14JR-* (round cover plate)11 1/8"[283mm]*SUFFIX FOR JUNCTION BOXES15/16"[23.8mm]10 7/8"[276mm]2 9/16"[65mm]15 1/2"[394mm]1 5/8"[41mm]14HS-* Heavy Duty (square)14HR-* Heavy Duty (round)222HS-* Heavy Duty (square)222HR-* Heavy Duty (round)*SUFFIX FOR JUNCTION BOXES15/16"[24mm]10 7/8"[276mm]2 9/16"[65mm]15 1/2"[394mm]1 5/8"[41mm]15/16"[23.8mm]*SUFFIX FOR JUNCTION BOXES15" [381mm]1 5/8"[41mm]224HS-* Heavy Duty (square)224HR-* Heavy Duty (round)2 9/16"[65mm]19 5/8"[499mm]18 5/8"[473mm]18 3/8"[467mm]1 5/8"[41mm]244HS-* Heavy Duty (square)244HR-* Heavy Duty (round)*SUFFIX FOR JUNCTION BOXES15/16"[23.8mm]25"[584mm]2 9/16"[65mm]DEPTH OF CONCRETE OVER DUCTDEPTH OF CONCRETE OVER DUCTmax.max.max.max.max.max.Junction Box – Two No. 4 ductsper side. Square cover platemeasures 18 3/8" x 18 3/8"[467mm x 467mm]. Diameterof round cover plate is 16.438"[418mm]. Specify suffix.DEPTH OF CONCRETE OVER DUCT11"[25mm] min. to 1 1/2" [35mm]1 1/21 1/2" [38mm] min. to 2"[51mm]22"[51mm] min. to 2 1/2" [62mm]2 1/22 1/2" [64mm] min. to 3"[76mm]33"[76mm] min. to 3 1/2" [89mm]3 1/23 1/2" [89mm] min. to 4"[102mm]*Other junction box heights are available. Consult factory for availability.10max.max.max.max.max.max.Junction Box – One No. 2duct and one No. 4 duct per side.Square cover plate measures 15"x 15" [381mm x 381mm]. Diameterof round cover plate is 13.063"[332mm]. Specify suffix.11"[25mm] min. to 1 1/2" [35mm]1 1/21 1/2" [38mm] min. to 2"[51mm]22"[51mm] min. to 2 1/2" [62mm]2 1/22 1/2" [64mm] min. to 3"[76mm]33"[76mm] min. to 3 1/2" [89mm]3 1/23 1/2" [89mm] min. to 4"[102mm]*Other junction box heights are available. Consult factory for availability.244JS-* (square cover plate)244JR-* (round cover plate)max.max.max.max.max.max.Junction Box – Two No. 2 ducts perside. Square cover plate measures10 7/8" x 10 7/8" [276mm x 276mm].Diameter of round cover plate is8.948" [227mm]. Specify suffix.11"[25mm] min. to 1 1/2" [35mm]1 1/21 1/2" [38mm] min. to 2"[51mm]22"[51mm] min. to 2 1/2" [62mm]2 1/22 1/2" [64mm] min. to 3"[76mm]33"[76mm] min. to 3 1/2" [89mm]3 1/23 1/2" [89mm] min. to 4"[102mm]*Other junction box heights are available. Consult factory for availability.224JS-* (square cover plate)224JR-* (round cover plate)15 1/4"[387mm]DEPTH OF CONCRETE OVER DUCT1"[25mm] min. to 1 1/2" [35mm]11 1/2" [38mm] min. to 2"[51mm]1 1/22"[51mm] min. to 2 1/2" [62mm]22 1/2" [64mm] min. to 3"[76mm]2 1/233"[76mm] min. to 3 1/2" [89mm]3 1/23 1/2" [89mm] min. to 4"[102mm]*Other junction box heights are available. Consult factory for availability.222JS-* (square cover plate)222JR-* (round cover plate)11 1/8"[283mm]Junction Box – One No. 4 duct perside. No interior partitioning. Squarecover plate measures 10 7/8" x 10 7/8"[276mm x 276mm]. Diameter of roundcover plate is 8.948" [227mm].Specify suffix.max.max.max.max.max.max.
Walkerduct Junction Boxes Ordering Information (Continued)ItemCatalog No./Description/Specifications3222JS-* (square cover plate)3222JR-* (round cover plate)15 1/4"[387mm]3222HS-* Heavy Duty (square)3222HR-* Heavy Duty (round)*SUFFIX FOR JUNCTION BOXES15/16"[23.8mm]15" [381mm]1 5/8"[41mm]2 9/16"[65mm]19 5/8"[499mm]18 3/8" [467mm]1 5/8"[41mm]3224HS-* Heavy Duty (square)3224HR-* Heavy Duty (round)*SUFFIX FOR JUNCTION BOXES15/16"[23.8mm]2 9/16"[65mm]23"[584mm]3424HS-* Heavy Duty (square)3424HR-* Heavy Duty (round)22"[559mm]21 3/4" [553mm]1 5/8"[41mm]2 9/16"[65mm]26 5/8"[670mm]*SUFFIX FOR JUNCTION BOXES22"[559mm]21 3/4" [553mm]1 5/8"[41mm]3244HS-* Heavy Duty (square)3244HR-* Heavy Duty (round)*SUFFIX FOR JUNCTION BOXES15/16"[23.8mm]26 5/8"[670mm]2 9/16"[65mm]DEPTH OF CONCRETE OVER DUCTDEPTH OF CONCRETE OVER DUCTmax.max.max.max.max.max.Junction Box – One No. 2Duct and two No. 4 Ducts perside. Square cover plate measures21 3/4"x 21 3/4" [553mm x 553mm].Diameter of round cover plate is19.813". [503mm]. Specify suffix.DEPTH OF CONCRETE OVER DUCT11"[25mm] min. to 1 1/2" [35mm]1 1/21 1/2" [38mm] min. to 2"[51mm]22"[51mm] min. to 2 1/2" [62mm]2 1/22 1/2" [64mm] min. to 3"[76mm]33"[76mm] min. to 3 1/2" [89mm]3 1/23 1/2" [89mm] min. to 4"[102mm]*Other junction box heights are available. Consult factory for availability.11max.max.max.max.max.max.Junction Box – Two No. 4 Ducts andone No. 2 Duct per side. The No. 2Duct is centered between the twoNo. 4 Ducts. Square cover platemeasures 21 3/4" x 21 3/4"[553mm x 553mm]. Diameter ofround cover plate is 19.813"[503mm]. Specify suffix.11"[25mm] min. to 1 1/2" [35mm]1 1/21 1/2" [38mm] min. to 2"[51mm]22"[51mm] min. to 2 1/2" [62mm]2 1/22 1/2" [64mm] min. to 3"[76mm]33"[76mm] min. to 3 1/2" [89mm]3 1/23 1/2" [89mm] min. to 4"[102mm
Flush service fittings are available in brass, brushed aluminum and nonmetallic finishes and can be fitted with modular communication inserts. Our pedestal service fittings, Multiplex Service Fittings and 525 Series Fittings, can be used on either system. In addition, flush carpet trim plates are avail
Read the following documents before using the PHANTOMTM 4 Pro / Pro : 1. In the Box 2. Phantom 4 Pro / Pro User Manual 3. Phantom 4 Pro / Pro Quick Start Guide 4. Phantom 4 Pro / Pro Series Disclaimer and Safety Guidelines 5. Phantom 4 Pro / Pro Series Intelligent Flight Battery Safety Guidelines
behringer ultra-curve pro dsp 24 a/d- d/a dsp ultra-curve pro ultra- curve pro 1.1 behringer ultra-curve pro 24 ad/da 24 dsp ultra-curve pro dsp8024 smd (surface mounted device) iso9000 ultra-curve pro 1.2 ultra-curve pro ultra-curve pro 19 2u 10 ultra-curve pro ultra-curve pro iec . 7 ultra-curve pro dsp8024 .
Pro Tools 9.0 provides a single, unified installer for Pro Tools and Pro Tools HD. Pro Tools 9.0 is supported on the following types of systems: Pro Tools HD These systems include Pro Tools HD software with Pro Tools HD or Pro Tools HD Native hard-ware. Pro Tools These systems include Pro Tools software with 003 or Digi 002 family audio .
SMB_Dual Port, SMB_Cable assembly, Waterproof Cap RF Connector 1.6/5.6 Series,1.0/2.3 Series, 7/16 Series SMA Series, SMB Series, SMC Series, BT43 Series FME Series, MCX Series, MMCX Series, N Series TNC Series, UHF Series, MINI UHF Series SSMB Series, F Series, SMP Series, Reverse Polarity
behringer v-amp pro 19 2 hu 10 cm v-amp pro 8.2 v-amp pro 3 2 v-amp pro 180 ( 120 v) 9 9 8. 11 v-ampire/v-amp pro/v-amp 2 8 iec 8.1 xlr 8.2 6.3 mm 8.3 6.3 mm 8.4 8.3 midi midi 5 din v-amp pro midi midi midi inmidi edit midi out/thru midi out (midi thru) v-amp pro midi midi 8.3.1 midi-sysex v-amp pro edit midi (a ) midi sysex v-amp pro edit
DUCT CABLE/WIRE SIZE FILL CHART DIAMETER AREA (In 2) 40% FILL* CABLE/WIRE SIZE No. 2 No. 4 Inches [mm ]Inches [mm ] DUCT DUCT UNSHIELDED 4-PAIR, 24 AWG, CAT 5 0.220 [5.6] 0.038 [24.5] 35 91 . Compare and coordinate the architectural and electrical drawings with Wiremold/Legrand installation drawings.
The steppingstone to the iDWC is the iRacing Pro Series, which also consists of two series, the iRacing Pro Series for Ovals (iPSO) and the iRacing Pro Series for Road Racing (iPSRR). These series are open to a broader spectrum of Pro-level license holders and serve as qualifying series for the iRacing Drivers World Championships.
AGMA and/or DIN standards IMPERIAL Series Load Rating Drum Capacity METRIC Series Power Supply Line Speed Clutch Load Rating Drum Capacity Power Supply Line Speed Clutch PERFORMANCE 4WS9M18 4WS16M20 4WS26M26 4WS1M6 4WS3M10 4WS6M12 10,000 lbs 16,000 lbs 26,200 lbs 1,500 lbs 3,700 lbs 6,400 lbs 5–10 hp 7.5–15 hp 10–25 hp.5–1.5 hp 1–3 hp .
