European Technical Approval ETA-06/0029
Centre Scientifique etTechnique du Bâtiment84, avenue Jean JaurèsChamps-sur-MarneF-77447 Marne La Vallée Cedex 2Tél. : (33) 01 64 68 82 82Fax : (33) 01 60 05 70 37Autorisé etnotifié conformément àl’article 10 de la directive89/106/EEC du Conseil, du21 décembre 1988, relative aurapprochement des dispositionslégislatives, réglementaireset administratives des Etatsmembres concernantles produits deconstruction.European Technical ApprovalEOTA MEMBERETA-06/0029(English language translation, the original version is in French language)Trade name:FORCEHolder of approval:Titulaire:AXTER8, rue Félix d’HérelleF-75016 PARISGeneric type and use ofconstruction product:Systems of mechanically fastened flexible roofwaterproofing membranesValidity from:to:10/07/200609/07/2011Manufacturing plant:Usine de fabrication:Usine AXTER1, rue Joseph CosteF-59552 COURCHELETTESThis European Technical Approvalcontains:28 pages including 18 annexes which form an integral partof the document.Nom commercial:Type générique et utilisation prévue duproduit de construction:Valide du/au:Le présent Agrément Technique Européencontient:Systèmes de feuilles souples d’étanchéités de toitures fixésmécaniquement28 pages incluant 18 annexes faisant partie intégrante du document.European Organisation for Technical ApprovalsOrganisation pour l’Agrément Technique Européen
Page 2 - European Technical Approval ETA-06/0029Validity from 10/07/2006 to 09/07/2011ILEGAL BASES AND GENERAL CONDITIONS1-This European Technical Approval is issued by the Centre Scientifique etTechnique du Bâtiment (CSTB) in accordance with:Council Directive 89/106/EEC of 21 December 1988 on the approximationof laws, regulations and administrative provisions of Member States relating1to construction products , modified by the Council Directive 93/68/EEC of222 July 1993 ;3Décret no. 92-647 du 8 juillet 1992 concernant l’aptitude à l’usage desproduits de construction;Common Procedural Rules for Requesting, Preparing and the Granting ofEuropean Technical Approvals set out in the Annex of Commission4Decision 94/23/EC ;Guide d’Agrément Technique Européen ‘’Systèmes de feuilles souplesd’étanchéités de toitures fixés mécaniquement’’ n 006, Mai 2002, frenchversion of the ETAG 006, March 2000.12342-The Centre Scientifique et Technique du Bâtiment is authorised to checkwhether the provisions of this European Technical Approval are met.Checking may take place in the manufacturing plant (for example concerningthe fulfilment of assumptions made in this European Technical Approval withregard to manufacturing). Nevertheless, the responsibility for the conformityof the products with the European Technical Approval and for their fitness forthe intended use remains with the holder of the European TechnicalApproval.3-This European Technical Approval is not to be transferred by CSTB tomanufacturers or agents of manufacturer other than those indicated on page1; or manufacturing plants other than those indicated on page 1 of thisEuropean Technical Approval.4-This European Technical Approval may be withdrawn by the CentreScientifique et Technique du Bâtiment pursuant to Article 5 of the CouncilDirective 89/106/EEC.5-Reproduction of this European Technical Approval including transmissionby electronic means shall be in full. However, partial reproduction can bemade with the written consent of the Centre Scientifique et Technique duBâtiment. In this case, partial reproduction has to be designated as such.Texts and drawings of advertising brochures shall not contradict or misusethe European Technical Approval.6-The European Technical Approval is issued by the approval body in itsofficial language. This version corresponds to the version circulated withinEOTA. Translations into other languages have to be designated as such.Official Journal of the European Communities no. L 40, 11.2.1989, p. 12Official Journal of the European Communities no. L 220, 30.8.1993, p. 1Journal Officiel de la République française du 14 juillet 1992Official Journal of the European Communities no. L 17, 20.1.1994, p. 34
Page 3 - European Technical Approval ETA-06/0029Validity from 10/07/2006 to 09/07/2011IISPECIFIC CONDITIONS OF THE EUROPEAN TECHNICAL APPROVAL1Definition of product and intended use1.1Definition of productThe systems of mechanically fastened flexible roof waterproofing membrane,subject of this ETA and called MEFAWAME in the text, are waterproofing kitscomposed of two-layers flexible roof waterproofing systems mechanicallyfastened with point fasteners to the structure, with a slope 1%. The first layer isndfastened with overlappings eventually welded. The 2 layer is torched welded onstthe 1 layer.The MEFAWAME is composed of flexible membranes manufactured by theholder of the approval and mechanical fasteners manufactured by othersmanufacturers.1.1.1MembranesFirst layer (fastened)MATFIXMATFIX S3RTOPFIX FMP gréséTOPFIX FMPSecond layerFORCE 4000 SFORCE 4000 S FEFORCE 4000 FMGFORCE 4000 FMG FERUBEROOF 4025 AFORCE 50 G FMPYE PV 200 S5FORCE 4000 SFORCE 4000 S FEFORCE 4000 FMGFORCE 4000 FMG FERUBEROOF 4025 AFORCE 50 G FMPYE PV 200 S5FORCE 4000 SFORCE 4000 S FEFORCE 4000 FMGFORCE 4000 FMG FERUBEROOF 4025 AFORCE 50 G FMPYE PV 200 S5FORCE 4000 SFORCE 4000 S FEFORCE 4000 FMGFORCE 4000 FMG FERUBEROOF 4025 AFORCE 50 G FMPYE PV 200 S5
Page 4 - European Technical Approval ETA-06/0029Validity from 10/07/2006 to 09/07/2011Composition of the membranesMembraneBitumenMATFIXMATFIX S3RTOPFIX FMPTOPFIX FMP gréséFORCE 4000 SFORCE 4000 S FEFORCE 4000 FMGFORCE 4000 FMG FERUBEROOF 4025 AFORCE 50 G FMPYE PV 200 S5Elastomeric(SBS) binderElastomeric(SBS) binderElastomeric(SBS) binderElastomeric(SBS) binderElastomeric(SBS) binderElastomeric(SBS) binderElastomeric(SBS) binderElastomeric(SBS) binderElastomeric(SBS) binderElastomeric(SBS) binderElastomeric(SBS) binderAveragethickness onselvedgeReinforcementSurfaceUnderside1.6 (1)Glass fibreFilmPolyester3.0 (1)Glass fibre2.652.654.04.04.04.04.04.2 (2)5.2 esterReinforcedpolyester(1) Average overall thickness(2) Average thickness on mineral granules(3) Minimum thickness on mineral granulesMacro-perforatedfilm and sandMacro-perforatedfilm and sandMacro-perforatedfilm and sandSlate chippings ormineral granulesSlate chippings ormineral granulesSlate chippings ormineral granulesSlate chippings ormineral granulesSlate chippings ormineral granulesSlate chippings ormineral granulesSlate chippings ormineral rmofusiblefilmThermofusiblefilmThe characteristics of these membranes are presented in Annexes 1 to 11. For allthe membranes with mineral protection, the loss of mineral granule, tested inconformity with the EN 12039, is 30%.1.1.2FastenersThe fastener, manufactured by the manufacturer LR ETANCO, is:screw VMS 2C plate 40x40Composition of the fastener:Screw VMS 2C: hardened carbon steel screw. Diameter of 4,8 mm, length Land with a 8.5 mm circular head. Supracoat corrosion protection.Resistance at 15 Kesternich cycles (EN ISO 6988). 40x40 : steel plate 40x40 mm, thickness 0.8 mm. Hole Ø 4.5 mm.Aluzinc AZ 150 protection.PlateThe fastener is conform to the specifications of the ETAG 006. It owns a FastenerPASS ‘’Intermediate evaluation in compliance with the European TechnicalApproval Guideline n 006’’.The flexible membranes and the fastener are commercialised in separatetransactions and assembled on site.The different kits are presented in Annexes 13.The holder of the ETA is fundamentally responsible of the kit.
Page 5 - European Technical Approval ETA-06/0029Validity from 10/07/2006 to 09/07/20111.2Intended useThe kits for the waterproofing of roof surfaces against penetration of atmosphericwater are intended for uses where requirements concerning safety in case of fire,hygiene, health and the environment and safety in use as well as the durability inthe sense of the essential requirements N 2 to N 4 of the Directive 89/106/EECshall be satisfied.The bearing elements are metallic, in concrete, in lightweight concrete or in wood.The bearing elements can be direct substrates of the MEFAWAME. In the casewhere the insulation is the direct substrate of the MEFAWAME, it shall beconform with the requirements of § 4.2.2. The insulation is not a part of the kit.5In the manufacturer's technical dossier (MTD) to this European technicalapproval (ETA) the manufacturer gave information concerning the substratewhich the roof waterproofing is suitable for.The verifications which are based on this ETA give reason for the assumption ofan intended working life of the roof waterproofing of at least 10 years.The indications given on the working life cannot be interpreted as a guaranteegiven by the producer, but are regarded only as a means for choosing the rightproducts in relation to the expected economically reasonable working life of theworks.The part of the MTD to this ETA to be treated confidentially is deposited withCSTB and, as far as this is relevant to the tasks of the notified body involved inthe procedure of attestation of conformity, shall be handed over to the notifiedbody.2Characteristics of product and methods of verification2.1Characteristics of products and systemsThe components of the roof waterproofing kit show the characteristic values withrespect to the permissible tolerances which are stated in the MTD to this ETA.The ETA is issued for the kit on the basis of the product composition depositedwith CSTB. Changes to the components of the kit or in the production process ofthe components, which could result in the production process and/or theproperties of the product deposited being incorrect should be notified to CSTBbefore the changes are introduced. CSTB will decide whether or not suchchanges affect the ETA and consequently the validity of the CE marking on thebasis of the ETA and if so whether further assessment/alterations to the ETA shallbe necessary.The performances of the bituminous membranes, the fasteners and the kits arepresented in Annexes 1 to 14.2.2Methods of verificationAssessment of the fitness of the roof waterproofing for the intended use withregard to the essential requirements N 2 to N 4 was performed following the"Guideline for European Technical Approval of systems of mechanically fastenedflexible roof waterproofing membranes" (ETAG 006).According to the manufacturer's declaration the roof waterproofing taking account6of the EU database does not contain any dangerous or forbidden substances.The manufacturer's technical dossier (MTD) comprises all information necessary for the production and theprocessing of the product. It was checked by CSTB and it was found to be in accordance with the conditions stated inthe approval and the characteristic values determined during the approval testing. The part of the MTD to this ETA tobe treated confidentially is deposited with CSTB and, as far as this is relevant to the tasks of the notified body involvedin the procedure of attestation of conformity, shall be handed over to the notified body.
Page 6 - European Technical Approval ETA-06/0029Validity from 10/07/2006 to 09/07/2011Within the scope of this approval there may be other requirements applicable todangerous substances resulting from transposed European legislation orapplicable national regulations and administrative provisions.These requirements need also to be complied with. Moreover, this assessmentcould be extended with other requirements applicable to the products, resultingfrom the application of other national regulations and administrative provisions.3Evaluation of Conformity and CE marking3.1Attestation of conformity systemThe European Commission according to the decision (98/143/EC of February1998, Official Journal of the European Communities No. L 42, 14.02.1998) on theProcedures of Attestation of Conformity has, for this type of product, laid down a:System 2 , for the procedure of attestation of conformity (Annex III, clause 2(ii)first possibility of Directive 89/106/EEC) for Systems of mechanically fastenedflexible roof waterproofing membranes. The system of attestation of conformity 2 (referred to as system 2 ) provides:a) Tasks of the manufacturers:1. Initial type testing of the product2. Factory production controlb) Tasks of the Notified Body:3. initial inspection of factory and of factory production control (FPC)4. continuous surveillance, assessment and approval of factory productioncontrol3.2Responsabilities3.2.1Tasks of the manufacturer3.2.1.1 Factory production controlThe manufacturer of flexible membranes and the manufacturers of fastenershave different factory production control (FPC) systems.The manufacturer of flexible membranes has a factory production control (FPC)system in its plant and exercises permanent internal control of production. ThisFPC is conform to the EN 13707. All the elements, requirements and provisionsadopted by the manufacturer are documented in a systematic manner in the formof written policies and procedures. This production control system ensures thatthe product is in conformity with the European Technical Approval.The manufacturers of fasteners have a factory production control system in theirplant and exercise permanent internal control of production. This FPC is conformto the ETAG 006. All the elements, requirements and provisions adopted by themanufacturer are documented in a systematic manner in the form of writtenpolicies and procedures. This production control system ensures that the productis in conformity with the European Technical Approval.The manufacturer of flexible membranes and the manufacturers of fasteners shalluse raw materials or components that comply with the indications of the MTD.The content of the control plan has been checked by CSTB and is stipulated inthe MTD.The results of the factory production control shall be recorded and evaluated. Therecords shall include at least the following information :Database ‘’Dangerous substances’’ consulted on the uction/internal/dangsub/dangmain.htm, version 17 march 2003.
Page 7 - European Technical Approval ETA-06/0029Validity from 10/07/2006 to 09/07/2011Name of the product and the raw materials,Type of inspection or control,Date of manufacture of the product, batch number, and date of inspection orcontrol of the product,Results of inspections or controls and, as far as applicable, comparison withrequirements,Signature of the person responsible for factory production control or hisrepresentant.The records shall be kept for at least five years. On request, they shall bepresented to CSTB.The control plan is a confidential part of the MTD and is deposited with CSTB.3.2.1.2 Initial type-testing of the productThe initial type-testing refers to the product properties stated in EOTA Guideline006 to this European technical approval.The verifications underlying this ETA have been furnished on samples(membranes and fasteners) from the current production. These will replace theinitial type-testing.After changing the production process or starting the production in anothermanufacturing plant the initial type-testing shall be repeated.3.2.1.3 Other tasks of the manufacturerThe manufacturers shall, on the basis of a contract, involve a body which isnotified for the tasks referred to in section 3. For this purpose, the control planreferred to in section 3.2.2 shall be handed over by the manufacturer to thenotified body involved.3.2.2Tasks of the Notified Bodies3.2.2.1 Initial inspection of factory and production control.The CSTB ascertains that, in accordance with the MTD, factory conditions andproduction control allow the manufacturer to ensure the consistency andhomogeneity of the manufactured product and its traceability, thus guaranteeingthat the final characteristics of the product are those indicated in chapter 2.3.2.2.2 Continuous surveillance, assessment and approval of Factory Production ControlThe Notified Body shall visit the factory of flexible membranes and the factories offasteners once a year.Surveillance of the manufacturing processes shall include:Checking the documentation of factory production control, to ensurecontinuing compliance with the provisions of the ETA,Identification of changes by comparing data obtained during the initialinspection or during the last inspection.In the event the ETA provisions are not complied with, the certificate of conformityshall be withdrawn by the notified body and CSTB will be informed without delay.
Page 8 - European Technical Approval ETA-06/0029Validity from 10/07/2006 to 09/07/20113.3CE MarkingThe CE marking shall be affixed on the kit, components itself/themselves, anattached label, the packaging, or the accompanying commercial document.The required information to accompany the symbol ‘’CE’’ is :name or identifying name of the producer,number of the notified body involved (system 2 ),number of the certificate of conformity of the Factory Production Control(system 2 )last two digits of the year in which the CE marking was affixed,number of the ETA,number of the ETAG.The components shall be marked as belonging to the kit FORCE.4Assumptions under which the fitness of the product for the intended usewas favourably assessed4.1Installation and designInformation concerning installation and design is part of the non confidential partof the MTD.See Technical Notices in Annexes 15 to 18.The flexible membranes manufacturer’s installation guide forms part of this ETA.The design of the roof intended to be covered by the mechanically fastened roofwaterproofing system should take account of the following factors :Dead and imposed loadsDesign wind pressureStructural strength, stiffness and deflection limitsAttachment of the roof deck to the structural framingProvision of insulationAssessment of condensation risk and provision of vapour control layersSound insulationFire precautionsRoof attachments, fixtures and penetrationsFalls and drainageMeans of access for inspection and maintenance4.2SubstratesThe substrate onto which the waterproofing kit is to be laid should be sufficientlyrigid, dense, and dimensionally stable to support the system (membrane insulation). Its nature will depend on the type of roof selected (warm deck, colddeck or inverted) and in turn will have a direct influence on the method ofattachment.In order to support the loads imposed by traffic, insulation materials for use inwarm decks should be capable of resisting permanent deformation or damagewhen subjected to concentrated loads. They should have a dust-free surface andsufficient laminar strength to resist with a margin of safety and stress imposed bywind uplift forces.It shall be ensured that the insulation material on site has:a 10% compression 60kPa (EN 826)a point load behaviour 500 Pa, deformation 5 mm (EN 12430)The insulation material must be CE marked according to the harmonizedEuropean standard.
Page 9 - European Technical Approval ETA-06/0029Validity from 10/07/2006 to 09/07/20114.3Flexible membranes manufacturer’s responsibilitiesIt is the manufacturer's responsibility to make sure that all those who use the kitare appropriately informed about the specific conditions according to sections 1,2, 4, and 5 including the annexes to this ETA and the not confidential parts of theMTD to this ETA.5Informations by the manufacturerInformation about packaging, transport, storage, maintenance and repair are partof the non confidential part of the MTD.5.1Packaging, transport and storageThis product is not toxic, so it is not necessary to follow any safety instructions fortransport and handling.Storage must be at temperatures between -25 C and 45 C, in dry, and protectedagainst direct sunlight.Rolls must always be stored vertically.The product must keep away from any source of heat, sparks, flame, etc.5.2Maintenance and repair of the worksThe assessment of the fitness for use is based on the assumption that a normalmaintenance of the system is performed.This maintenance shall include :inspections of the roof at regular interval, e.g. twice a yearthis inspection should include : cleaning of downpipes and leaf filters removal of stones, branches and leafs inspection of flashings along the edge of the roof, chimneys, drains and rooflights
Page 10 - European Technical Approval ETA-06/0029Validity from 10/07/2006 to 09/07/2011 removal of organic growths such as vinesElastic joints around cover strips should be inspected every 5 years andreplaced if necessaryFlashings to caps, drains etc. should be inspected every 5 years andreplaced if necessaryAbrasion and minor impact damage shall be repaired.When replacing components they shall be approved by the manufacturer andcovered by the ETA.
Page 11 - European Technical Approval ETA-06/0029Validity from 10/07/2006 to 09/07/20118, avenue Félix d'Hérelle F-75016 PARISTel: 00 33 1 46 09 39 60 - Fax : 00 33 1 46 09 39 61CHARACTERISTICSTEST METHODUNITSVALUE orSTATEMENTEN 12316-1(N/50mm)NREN 12317-1(N/50mm)NREN 1109 C-18Decrease afterageing 15 C-20Decrease afterageing 15 CEN 12310-1NEN 12311-1N/50 mmEN 12311-1%Resistance to impactEN 12691mm30Resistance to static loadingEN 12730kg15Dimensional stabilityEN 1107-1%0.3EN 1928:2000-PassEN 1931-µ 20000EN 13501-1-FMaximal strengthPeel resistance ofjointsAverage strengthShear resistance ofjointsMaximal strengthSurfaceBefore heatLengthageingWidthAfter heat ageing LengthEN 1296WidthBefore heatLengthageingWidthAfter heat ageing LengthEN 1296WidthBefore heatLengthageingWidthAfter heat ageing LengthEN 1296WidthBefore heat ageingAfter heat ageing EN 1296Flexibility at lowtemperatureBefore heat ageingUndersideResistance to tearing(nail shank)LengthTensile properties:maximum tensileforceLengthTensile properties:elongationLengthAfter heat ageing EN 1296WidthWidthWidthWatertightnessWater vapour transmission propertiesReaction to 00200400324324NR: Not RelevantMEFAWAME ‘’FORCE’’System of mechanically fastened flexible roof waterproofing membranesCharacteristics of MATFIXAnnex 1of European TechnicalApprovalETA-06/0029
Page 12 - European Technical Approval ETA-06/0029Validity from 10/07/2006 to 09/07/20118, avenue Félix d'Hérelle F-75016 PARISTel: 00 33 1 46 09 39 60 - Fax : 00 33 1 46 09 39 61CHARACTERISTICSMaximal strengthPeel resistance ofjointsAverage strengthShear resistance ofjointsFlexibility at lowtemperatureResistance to tearing(nail shank)Tensile properties:maximum tensileforceMaximal strengthSurfaceBefore heatLengthageingWidthAfter heat ageing LengthEN 1296WidthBefore heatLengthageingWidthAfter heat ageing LengthEN 1296WidthBefore heatLengthageingWidthAfter heat ageing LengthEN 1296WidthBefore heat ageingTEST METHODUNITSVALUE orSTATEMENTEN 12316-1(N/50mm)NREN 12317-1(N/50mm)NREN 1109 C-18Decrease afterageing 15 C-20Decrease afterageing 15 CEN 12310-1NAfter heat ageing EN 1296UndersideBefore heat ageingAfter heat ageing EN 00300200400324324EN 12311-1N/50 mmEN 12311-1%EN 12691mmResistance to static loadingEN 12730kg15Dimensional stabilityEN 1107-1%0.3EN 1928:2000-PassEN 1931-µ 20000EN 13501-1-ETensile properties:elongationWidthLengthWidthResistance to impactWatertightnessWater vapour transmission propertiesReaction to fireTOLERANCESmini30NR: Not RelevantMEFAWAME ‘’FORCE’’System of mechanically fastened flexible roof waterproofing membranesCharacteristics of MATFIX S3RAnnex 2of European TechnicalApprovalETA-06/0029
Page 13 - European Technical Approval ETA-06/0029Validity from 10/07/2006 to 09/07/20118, avenue Félix d'Hérelle F-75016 PARISTel: 00 33 1 46 09 39 60 - Fax : 00 33 1 46 09 39 61CHARACTERISTICSTEST METHODUNITSVALUE orSTATEMENTEN 12316-1(N/50mm)NREN 12317-1(N/50mm)NREN 1109 C-14Decrease afterageing 15 C-18Decrease afterageing 15 CEN 12310-1NEN 12311-1N/50 mmEN 12311-1%Resistance to impactEN 12691mm20Resistance to static loadingEN 12730kg10Dimensional stabilityEN 1107-1%0.3EN 1928:2000-PassEN 1931-µ 20000EN 13501-1-FMaximal strengthPeel resistance ofjointsAverage strengthShear resistance ofjointsMaximal strengthSurfaceFlexibility at lowtemperatureBefore heatLengthageingWidthAfter heat ageing LengthEN 1296WidthBefore heatLengthageingWidthAfter heat ageing LengthEN 1296WidthBefore heatLengthageingWidthAfter heat ageing LengthEN 1296WidthBefore heat ageingAfter heat ageing EN 1296Before heat ageingUndersideResistance to tearing(nail shank)LengthTensile properties:maximum tensileforceLengthTensile properties:elongationLengthAfter heat ageing EN 1296WidthWidthWidthWatertightnessWater vapour transmission propertiesReaction to 70250310301045551080NR: Not RelevantMEFAWAME ‘’FORCE’’System of mechanically fastened flexible roof waterproofing membranesCharacteristics of TOPFIX FMP gréséAnnex 3of European TechnicalApprovalETA-06/0029
Page 14 - European Technical Approval ETA-06/0029Validity from 10/07/2006 to 09/07/20118, avenue Félix d'Hérelle F-75016 PARISTel: 00 33 1 46 09 39 60 - Fax : 00 33 1 46 09 39 61CHARACTERISTICSTEST METHODUNITSVALUE orSTATEMENTEN 12316-1(N/50mm)NREN 12317-1(N/50mm)NREN 1109 C-14Decrease afterageing 15 C-18Decrease afterageing 15 CEN 12310-1NEN 12311-1N/50 mmEN 12311-1%Resistance to impactEN 12691mm20Resistance to static loadingEN 12730kg10Dimensional stabilityEN 1107-1%0.3EN 1928:2000-PassEN 1931-µ 20000EN 13501-1-FMaximal strengthPeel resistance ofjointsAverage strengthShear resistance ofjointsMaximal strengthSurfaceBefore heatLengthageingWidthAfter heat ageing LengthEN 1296WidthBefore heatLengthageingWidthAfter heat ageing LengthEN 1296WidthBefore heatLengthageingWidthAfter heat ageing LengthEN 1296WidthBefore heat ageingAfter heat ageing EN 1296Flexibility at lowtemperatureBefore heat ageingUndersideResistance to tearing(nail shank)LengthTensile properties:maximum tensileforceLengthTensile properties:elongationLengthAfter heat ageing EN 1296WidthWidthWidthWatertightnessWater vapour transmission propertiesReaction to 70250310301045551080NR: Not RelevantMEFAWAME ‘’FORCE’’System of mechanically fastened flexible roof waterproofing membranesCharacteristics of TOPFIX FMPAnnex 4of European TechnicalApprovalETA-06/0029
Page 15 - European Technical Approval ETA-06/0029Validity from 10/07/2006 to 09/07/20118, avenue Félix d'Hérelle F-75016 PARISTel: 00 33 1 46 09 39 60 - Fax : 00 33 1 46 09 39 61CHARACTERISTICSTEST METHODUNITSVALUE orSTATEMENTEN 12316-1(N/50mm)NREN 12317-1(N/50mm)NREN 1109 C-18Decrease afterageing 15 C-20Decrease afterageing 15 CEN 12310-1NEN 12311-1N/50 mmEN 12311-1%Resistance to impactEN 12691mm20Resistance to static loadingEN 12730kg20Dimensional stabilityEN 1107-1%0.3EN 1928:2000-PassEN 1931-µ 20000EN 13501-1-FMaximal strengthPeel resistance ofjointsAverage strengthShear resistance ofjointsMaximal strengthSurfaceBefore heatLengthageingWidthAfter heat ageing LengthEN 1296WidthBefore heatLengthageingWidthAfter heat ageing LengthEN 1296WidthBefore heatLengthageingWidthAfter heat ageing LengthEN 1296WidthBefore heat ageingAfter heat ageing EN 1296Flexibility at lowtemperatureBefore heat ageingUndersideResistance to tearing(nail shank)LengthTensile properties:maximum tensileforceLengthTensile properties:elongationLengthAfter heat ageing EN 1296WidthWidthWidthWatertightnessWater vapour transmission propertiesReaction to 50500730452555502560NR: Not RelevantMEFAWAME ‘’FORCE’’System of mechanically fastened flexible roof waterproofing membranesCharacteristics of FORCE 4000 SAnnex 5of European TechnicalApprovalETA-06/0029
Page 16 - European Technical Approval ETA-06/0029Validity from 10/07/2006 to 09/07/20118, avenue Félix d'Hérelle F-75016 PARISTel: 00 33 1 46 09 39 60 - Fax : 00 33 1 46 09 39 61CHARACTERISTICSTEST METHODUNITSVALUE orSTATEMENTEN 12316-1(N/50mm)NREN 12317-1(N/50mm)NREN 1109 C-18Decrease afterageing 15 C-20Decrease afterageing 15 CEN 12310-1NEN 12311-1N/50 mmEN 12311-1%EN 12691mmResistance to static loadingEN 12730kg20Dimensional stabilityEN 1107-1%0.3EN 1928:2000-PassEN 1931-µ 20000EN 13501-1-FMaximal strengthPeel resistance ofjointsAverage strengthShear resistance ofjointsMaximal strengthSurfaceFlexibility at lowtemperatureResistance to tearing(nail shank)Tensile properties:maximum tensileforceTensile properties:elongationUndersideBefore heatLengthageingWidthAfter heat ageing LengthEN 1296WidthBefore heatLengthageingWidthAfter heat ageing LengthEN 1296WidthBefore heatLengthageingWidthAfter heat ageing LengthEN 1296WidthBefore heat ageingAfter heat ageing EN 1296Before heat ageingAfter heat ageing EN 1296LengthWidthLengthWidthLengthWidthResistance to impactWatertightnessWater vapour transmission propertiesReaction to 5050073045255550256020NR: Not RelevantMEFAWAME ‘’FORCE’’System of mechanically fastened flexible roof waterproofing membranesCharacteristics of FORCE 4000 S FEAnnex 6of European TechnicalApprovalETA-06/0029
Page 17 - European Technical Approval ETA-06/0029Validity from 10/07/2006 to 09/07/20118, avenue Félix d'Hérelle F-75016 PARISTel: 00 33 1 46 09 39 60 - Fax : 00 33 1 46 09 39 61CHARACTERISTICSTEST METHODMaximal strengthPeel resistance ofjointsAverage strengthShear resistance ofjointsMaximal strengthSurfaceBefore heat ageingUndersideWidthLengthTensile 00730452555502560Decrease afterageing 20%160750EN 12317-1(N/50mm)EN 1109 CEN 12310-1NEN 12311-1N/50 mmDecrease afterageing 20%-18Decrease afterageing 15 C-20Decrease afterageing 15 CEN 12311-1%Resistance to impactEN 12691mm20Resistance to static loadingEN 12
PYE PV 200 S5 TOPFIX FMP FORCE 4000 S FORCE 4000 S FE FORCE 4000 FMG FORCE 4000 FMG FE RUBEROOF 4025 A FORCE 50 G FM PYE PV 200 S5 . . The insulation is not a part of the kit. In the manufacturer's technical dossier (MTD)5 to this European technical approval (ETA) the manufacturer gave information concerning the substrate .
Technical and Test Institute for Construction Prague Prosecká 811/76a 190 00 Prague Czech Republic eota@tzus.cz Member of www.eota.eu ETA 14/0138 of 20/05/2018 - Page 1 of 19 090-031673 European Technical Assessment ETA 14/0138 of 20/05/2018 Technical Assessment Body issuing the ETA: Technical and Test Institute for Construction Prague
Ideia hori nola bideratu erabaki behar genuen, ordea, baita adin-tarte horretan zer . , eta hainbat material didaktiko landu genituen hezkuntza-pakete bat osatzeko. Jarraian, . oparitu zigun, eta «Iris eta Lila» ipuina idatzi zuen. Jesús Mentxaka koadernoak lantzeko ariketez eta gida didaktikoez arduratu zen .
La Gioconda edo Mona Lisa, 1503. Leonardo da Vinci. Venusen jaiotza, 1483. Sandro Botticelli EDERTASUN KANONAK XV. MENDEAN Edertasun-kanon femeninoa: emakumeak azal zuria eta masailak gorriztak izatea zen onena; hilea horia eta luzea, eta begi handi eta argiak. Gorputz perfektutzat jotzen ziren sorbalda estuak, aldakak pixka bat markatuak eta
MEKATRONIKA INDUSTRIALA 6 informazioaren eta komunikazioaren teknologiak ere, eguneratzeizpirituari eusteko - eta laneko egoera berrietara eta egoera pertsonal berrietara egokitzeko. 17. Sormena eta berrikuntzako izpiritua garatzea, lanaren eta norberaren bizitzaren prozesuetan e
R56 action with ETA required as of July 2017 before your R56 certification fully expires; contact ETA, C.A. proctor, and sit for R56 certification exam upon completion of the following: Review/Study: R56 Prep Guide (V.5.0) R56 2017 Standards Manual 68P81089E50-C ETA R56 Competencies
tailerra eta ipuina. Hizkuntzari dagokionez, hizkuntza bera nola irakatsi eta nola ikasi behar den pentsatu beharra dugu. Tailerrari dagokionez, ikasleak hizkun-tzaz duen ikuspegia zabaltzea lortu nahi da, irakasle eta ikasleen lana bate-ratu eta hartan oinarrituta. Ipuinari dagokionez, bestalde, egun ikasleek
Bridge Committee Eta Kappa Nu, Mu Chapter 290 Cory Hall UC Berkeley, Berkeley, CA 94720 Tel.: (510)642-7346 E-mail: bridge@hkn.berkeley.edu BRIDGE Magazine Eta Kappa Nu Association P.O. Box 3535 Lisle, IL 60532
The most popular agile methodologies include: extreme programming (XP), Scrum, Crystal, Dynamic Sys-tems Development (DSDM), Lean Development, and Feature Driven Development (FDD). All Agile methods share a common vision and core values of the Agile Manifesto. Agile Methods: Some well-known agile software development methods include: Agile .
