Cisco DX Series Administration Guide, Release 10.2(5)
Cisco DX Series Administration Guide, Release 10.2(5)First Published: December 09, 2015Last Modified: February 08, 2016Americas HeadquartersCisco Systems, Inc.170 West Tasman DriveSan Jose, CA 95134-1706USAhttp://www.cisco.comTel: 408 526-4000800 553-NETS (6387)Fax: 408 527-0883
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS,INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND,EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITHTHE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY,CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipmentgenerates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense.The following information is for FCC compliance of Class B devices: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radiofrequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interferencewill not occur in a particular installation. If the equipment causes interference to radio or television reception, which can be determined by turning the equipment off and on, users areencouraged to try to correct the interference by using one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.Modifications to this product not authorized by Cisco could void the FCC approval and negate your authority to operate the productThe Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public domain versionof the UNIX operating system. All rights reserved. Copyright 1981, Regents of the University of California.NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED "AS IS" WITH ALL FAULTS.CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OFMERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUTLIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERSHAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, networktopology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentionaland coincidental.Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: http://www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnershiprelationship between Cisco and any other company. (1110R)The Bluetooth word mark and logo are registered trademarks owned by Bluetooth SIG, Inc., and any use of such marks by Cisco Systems, Inc., is under license.Google, Google Play, Android and certain other marks are trademarks of Google Inc.The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and othercountries. 2016Cisco Systems, Inc. All rights reserved.
CONTENTSPrefacePreface xiiiOverview xiiiGuide Conventions xiiiRelated Documentation xivTerminology Differences xvDocumentation, Support, and Security Guidelines xviCisco Product Security Overview xviCHAPTER 1New and Changed Information 1New and Changed in Release 10.2(5) 1CHAPTER 2Technical Specifications 3Physical and Operating Environment Specifications 3Network and Computer Port Pinouts 4Network Port Connector Pinouts 5Computer Port Connector Pinouts 5Ports Used by Cisco DX Series Devices 6Network Protocols 7Power Requirements 11Power Guidelines 12Power Reduction 12Power Save Mode 13EnergyWise Mode 13Power Negotiation Over LLDP 14Additional Information About Power 14External Devices 15USB Port and USB Serial Console Data Information 15Cisco DX Series Administration Guide, Release 10.2(5)iii
ContentsUse USB Console 16Behavior During Times of Network Congestion 17CHAPTER 3Device Descriptions 19Cisco DX70 Hardware 19Cisco DX70 Cable Installation 20Cisco DX80 Hardware 21Cisco DX80 Cable Installation 22Cisco DX650 Hardware 23Cisco DX650 Cable Installation 23No Radio Hardware 24CHAPTER 4Wi-Fi Network Setup 25Network Requirements 25Wireless LAN 26Wi-Fi Network Components 27AP Channel and Domain Relationships 27AP Interactions 27Access Point Association 28QoS in Wireless Network 28Set Up Flexible DSCP 30Cisco Unified Communications Manager Interaction 30802.11 Standards for WLAN Communications 30World Mode (802.11d) 31Wireless Modulation Technologies 32Radio Frequency Ranges 33Security for Communications in WLANs 33Authentication Methods 33Authenticated Key Management 34Encryption Methods 34AP Authentication and Encryption Options 35WLANs and Roaming 36CHAPTER 5Deployment 37Configuration Files 37Cisco DX Series Administration Guide, Release 10.2(5)iv
ContentsDetermine MAC Address 38Cisco Unified Communications Manager Device Addition Methods 38Autoregistration 39Autoregistration and TAPS 39Add Device in Cisco Unified Communications Manager 40Add Device with Bulk Administration Tool Phone Template 40Self-Provisioning 41Enable Self-Provisioning 41Cisco Unified Communications Manager User Addition 41Add User Directly to Cisco Unified Communications Manager 42Add User From External LDAP Directory 42Identify Device Model 43Configure Line Settings 43Associate User with Device 44Survivable Remote Site Telephony 45CHAPTER 6Installation 47Install Cisco DX Series Device 47Wireless LAN Setup 48Wireless LAN Setup in Cisco Unified Communications Manager Administration 48Provision Wireless LAN Profile 49Provision Wireless LAN Profile Group 49Network Settings Configuration 49Configure IPv4 50Renew IPv4 50Configure IPv6 50Renew IPv6 51Configure Ethernet Web Proxy 51Set Admin VLAN 51Set SW Port Speed 52Set PC Port Speed 52Connect to Wi-Fi Network 52Connect to Hidden Wi-Fi Network 53Configure Wi-Fi Web Proxy 53Configure Wi-Fi IP Settings 53Cisco DX Series Administration Guide, Release 10.2(5)v
ContentsSet Wi-Fi Frequency Band 54Mobile and Remote Access Through Expressway 54Enable user Credential Persistence for Expressway 55Convert a Device to Mobile and Remote Access through Expressway 55Convert an Expressway Device to VPN 56Convert an Off-Premise Device to On-Premise 56Add Problem Report Tool Server to Expressway HTTP Allow List 56Set the Allowed Authorization Request Rate 56Enable Alternate TFTP Server 57Set TFTP Server 1 57Set TFTP Server 2 57AnyConnect VPN 57Add VPN Connection Profile 58Connect to VPN 58Optimize Video Call Experience Over VPN 58Configure VPN in Cisco Unified Communications Manager 59VPN Configuration Settings 60VPN Authentication 61Startup Process 61Set TFTP Server Manually During Startup 63Startup Verification 63CHAPTER 7Contacts 65Contacts and Directories by Operating Mode 65Local Contacts 66Corporate Directory 66Set Alternate Phone Book Server 66Set Company Photo Directory 67Contacts Search 67Application Dial Rules 68Configure Application Dial Rules 68CHAPTER 8Self Care Portal Management 69Self Care Portal Overview 69Set Up User Access to the Self Care Portal 69Cisco DX Series Administration Guide, Release 10.2(5)vi
ContentsCustomize the Self Care Portal Display 70CHAPTER 9Accessories 71Bluetooth Accessories 71Bluetooth Device Profiles 71Handsfree Profile 71Phone Book Access Profile 72Enable Device Profiles 72Pair Bluetooth Accessory 73Disable Bluetooth 73Cable Lock 73External Cameras 73External Camera Settings 74Perform External Camera Postinstallation Checks 74External Speakers and Microphone 74Headsets 74Bluetooth Wireless Headsets 75Add Bluetooth Wireless Headset 76Remove Bluetooth Headset 76USB Headsets 77Enable USB Headset 77Disable USB Headset 77Wired Headsets 77Connect to Wired Headset 77Disable Wired Headset 77Video Displays 78Cisco DX650 Wall-Mount Kit 78Before You Begin 78Wall-Mount Components 79Install Wall-Mount 79CHAPTER 10Security Features 85Device Security 85Overview of Security Features 86Security Profiles 88Cisco DX Series Administration Guide, Release 10.2(5)vii
ContentsSE Android 88Upgrades and SE Android 89SE Android Troubleshooting 89Diagnose SE Android Policy Issues 89ADB Shell Limitations 89SE Android Log Collection 90Set Up Locally Significant Certificate 90SHA-256 Manufacturing Installed Certificate 91Secure Phone Calls 91Secure Phone Call Identification 92Secure Conference Call Identification 92Call Security Interactions and Restrictions 93Check Device Security Information Remotely 94Encryption for Barge 94802.1X Authentication Support 94Required Network Components 94Best Practices 95Screen Lock and Automatic Lock Setup 95Set Up Screen Unlock/Password Reset 96Set Administrator Password for Settings 97CHAPTER 11Features and Services 99Available Telephony Features 99Agent Greeting 100Enable Agent Greeting 100All Calls 100All Calls on Primary Line 100AutoAnswer 100Auto Dial 101Barge 101Busy Lamp Field 101Call Forward 101Calling Line Identification 102Calling Line Identification Presentation 102Cisco Extension Mobility 102Cisco DX Series Administration Guide, Release 10.2(5)viii
ContentsExtension Mobility Multi-User 102Set Up Cisco Extension Mobility 103Cisco Mobility 104Conference 104Secure Conference 104Divert 104Do Not Disturb 105Gateway Recording 105Hold Status 105Hold and Resume 105Music on Hold 105Ignore 105Message Waiting Indicator 106Mute 106Plus Dialing 106Protected Calling 106Ringtone Setting 106Ringtone 106Secure and Nonsecure Indication Tone 107Serviceability 107Shared Line 107Speed Dial 107Transfer 108Uniform Resource Identifier Dialing 108Video Toggle 108Voice Messaging System 108Set Up Visual Voicemail 108Set Up Visual Voicemail for Specific User or Group 109Feature Buttons 109Set Up Feature Control Policies 111Feature Control Policy Default Values 111Phone Button Templates 112Modify Phone Button Templates 112Configure Product-Specific Options 113Video Transmit Resolution Setup 124Cisco DX Series Administration Guide, Release 10.2(5)ix
ContentsInstant Messaging and Presence Setup 126Application Setup 126Enable Cisco UCM App Client 126Create End User to Log In to UCM App 127Subscribe User with UCM App 127Push Android APK Files Through Cisco Unified Communications Manager 127Add Android Service in Cisco Unified Communications Manager Administration 128Subscribe Device to Android Phone Service 128CHAPTER 12Customization 131Wideband Codec Setup 131Operating Modes 132Set Operating Mode 132Default Wallpaper 133Assign Wallpaper Control 133Specify Default Wallpaper (DX70 and DX80) 133Specify Default Wallpaper (DX650) 134SSH Access 134Unified Communications Manager Endpoints Locale Installer 135International Call Logging Support 135CHAPTER 13Maintenance 137Reset Device 137Reset Options and Load Upgrades 139Remote Lock 139Remote Lock Device 139Remote Wipe 140Remote Wipe Device 140Boot Alternate Image for Cisco DX70 140Boot Alternate Image for Cisco DX80 141Boot Alternate Image for Cisco DX650 141Data Migration 141Debugging Log Profiles 141Set Debugging Log Profile for Call Processing 142Reset Debugging Log Profile to Default 142Cisco DX Series Administration Guide, Release 10.2(5)x
ContentsUser Support 142Problem Report Tool 142Configure Customer Support Upload URL 143Take Screenshot From Web Browser 144Take Screenshot From Device 144Application Support 144CHAPTER 14Model Information Status and Statistics 145Model Information 145Device Status 146Status Messages 147Ethernet Statistics 151WLAN Statistics 152Audio Call Statistics 153CHAPTER 15Remote Monitoring 155Enable and Disable Web Page Access 155Access Device Web Page 156Device Information 157Network Setup 158Security Information 163Ethernet Statistics 165WLAN Setup 167Device Logs 169Streaming Statistics 169Cisco DX Series Administration Guide, Release 10.2(5)xi
ContentsCisco DX Series Administration Guide, Release 10.2(5)xii
Preface Overview, page xiii Guide Conventions, page xiii Related Documentation, page xiv Documentation, Support, and Security Guidelines, page xviOverviewThis book provides the information you need to understand, install, configure, and manage Cisco DX Seriesdevices on a network.Network engineers, system administrators, and telecom engineers should review this guide to learn the stepsthat are required to set up Cisco DX Series devices. The tasks described in this document involve configuringnetwork settings that are not intended for users. The tasks in this manual require familiarity with Cisco UnifiedCommunications Manager.Because of the complexity of an IP telephony network, this guide does not provide complete and detailedinformation for procedures that you need to perform in Cisco Unified Communications Manager or on othernetwork devices.Guide ConventionsThis document uses the following conventions:ConventionDescriptionboldface fontCommands and keywords are in boldface.italic fontArguments for which you supply values are in italics.[ ]Elements in square brackets are optional.{x y z}Alternative keywords are grouped in braces and separated by vertical bars.Cisco DX Series Administration Guide, Release 10.2(5)xiii
PrefaceRelated DocumentationConventionDescription[x y z]Optional alternative keywords are grouped in brackets and separated by verticalbars.stringA nonquoted set of characters. Do not use quotation marks around the string or thestring will include the quotation marks.screen fontTerminal sessions and information the system displays are in screen font.input fontInformation you must enter is in input font.italic screen fontArguments for which you supply values are in italic screen font. The symbol represents the key labeled Control - for example, the key combination D in a screen display means hold down the Control key while you press the D key. NoteCaution Nonprinting characters such as passwords are in angle brackets.Means reader take note. Notes contain helpful suggestions or references to material not covered in thepublication.Means reader be careful. In this situation, you might do something that could result in equipment damageor loss of data.Warnings use the following convention:AttentionIMPORTANT SAFETY INSTRUCTIONSThis warning symbol means danger. You are in a situation that could cause bodily injury. Before youwork on any equipment, be aware of the hazards involved with electrical circuitry and be familiar withstandard practices for preventing accidents. Use the statement number provided at the end of each warningto locate its translation in the translated safety warnings that accompanied this device. Statement 1071SAVE THESE INSTRUCTIONSRelated DocumentationCisco DX SeriesAll Cisco DX Series documentation is available at the following sco DX Series Administration Guide, Release 10.2(5)xiv
PrefaceTerminology DifferencesUser-oriented documents are available at the following tor-oriented documentation is available at the following e Cisco DX Series Wireless LAN Deployment Guide is available at the following ist.htmlTranslated publications are available at the following r-guides-list.htmlOpen Source license information is available as the following htmlRegulatory Compliance and Safety Information is available at the following isco Unified Communications ManagerSee the Cisco Unified Communications Manager Documentation Guide and other publications that are specificto your Cisco Unified Communications Manager release. Navigate from the following documentation anager/tsd-products-support-series-home.htmlCisco Business Edition 6000Refer to the Cisco Business Edition 6000 Documentation Guide and other publications that are specific toyour Cisco Business Edition 6000 release. Navigate from the following upport-series-home.htmlCisco and the EnvironmentRelated publications are available at the following URL:http://www.cisco.com/go/ptrdocsTerminology DifferencesThe following table highlights some of the differences in terminology found in the Cisco DX Series userguides, the Cisco DX Series Administration Guide, and the Cisco Unified Communications ManagerAdministration Guide.Cisco DX Series Administration Guide, Release 10.2(5)xv
PrefaceDocumentation, Support, and Security GuidelinesTable 1: Terminology DifferencesUser GuidesAdministration GuidesLine StatusBusy Lamp Field (BLF)Message IndicatorsMessage Waiting Indicator (MWI) or Message Waiting LampVoicemail SystemVoice Messaging SystemDocumentation, Support, and Security GuidelinesFor information on obtaining documentation, obtaining support, providing documentation feedback, reviewingsecurity guidelines, and also recommended aliases and general Cisco documents, see the monthly What’s Newin Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, w/whatsnew.htmlSubscribe to the What’s New in Cisco Product Documentation as a Really Simple Syndication (RSS) feedand set content to be delivered directly to your desktop using a reader application. The RSS feeds are a freeservice and Cisco currently supports RSS Version 2.0.Cisco Product Security OverviewThis product contains cryptographic features and is subject to U.S. and local country laws that govern import,export, transfer, and use. Delivery of Cisco cryptographic products does not imply third-party authority toimport, export, distribute, or use encryption. Importers, exporters, distributors, and users are responsible forcompliance with U.S. and local country laws. By using this product, you agree to comply with applicablelaws and regulations. If you are unable to comply with U.S. and local laws, return this product immediately.Further information regarding U.S. export regulations can be found at index.htm.Cisco DX Series Administration Guide, Release 10.2(5)xvi
CHAPTER1New and Changed Information New and Changed in Release 10.2(5), page 1New and Changed in Release 10.2(5)New and Changed ContentSectionAdded no radio hardwareNo Radio Hardware, on page 24Added alternate phone book serviceSet Alternate Phone Book Server, on page 66Added FIPS modeConfigure Product-Specific Options, on page 113Updated default wallpaper dimensions and foldersfor Cisco DX650Specify Default Wallpaper (DX650), on page 134Updated contact searchContacts Search, on page 67Added automatic problem report uploadConfigure Product-Specific Options, on page 113Added adminstrator password for SettingsSet Administrator Password for Settings, on page 97Cisco DX Series Administration Guide, Release 10.2(5)1
New and Changed InformationNew and Changed in Release 10.2(5)Cisco DX Series Administration Guide, Release 10.2(5)2
CHAPTER2Technical Specifications Physical and Operating Environment Specifications, page 3 Network and Computer Port Pinouts, page 4 Network Protocols, page 7 Power Requirements, page 11 External Devices, page 15 USB Port and USB Serial Console Data Information, page 15 Behavior During Times of Network Congestion, page 17Physical and Operating Environment SpecificationsTable 2: Physical and Operating Specifications for Cisco DX Series DevicesSpecificationValue or RangePhysical dimensions (H x W x Cisco DX70: 14.84 in. (377.1 mm) x 13.91 in. (353.1 mm) x 2.45 in. (62.3D)mm)Cisco DX80: 20.2 in. (51 2mm) x 22.2 in. (565 mm) x 3.5 in. (89 mm)Cisco DX650: 8.46 in. (215 mm) x 10.35 in. (263 mm) x 8.19 in. (208 mm)WeightCisco DX70: 8.5 lb (3.9 kg)Cisco DX80: 15.65 lb (7.1 kg)Cisco DX650: 3.81 lb (1.73 kg)Operating temperature32 to 104 F (0 to 40 C)Operating relative humidity10 to 95% (noncondensing)Storage temperature14 to 140 F (-10 to 60 C)Cisco DX Series Administration Guide, Release 10.2(5)3
Technical SpecificationsNetwork and Computer Port PinoutsSpecificationValue or RangePower, Cisco DX70Rated: 3.5A at 12V maximumLow Power Standby modeIntegrated EnergyWise supportPower, Cisco DX80Rated: 60 W maximumLow Power Standby modeIntegrated EnergyWise supportPower, Cisco DX650IEEE 802.3af (Class 3) or IEEE 802.3at (Class 4) Power over Ethernet(PoE) standards are supported.Compatible with both Cisco Discovery Protocol and Link Layer DiscoveryProtocol-Media Endpoint Discovery (LLDP-MED) PoE switch blades.Power budget: 13.7W (Cisco Discovery Protocol) or 15.1W (LLDP) for802.3AF and low-power USB peripheral support; greater than 15.4W and802.3AT required for high-power USB peripheral support.ConnectivityInternal 2-port Cisco Ethernet switchIEEE 802.11 a/b/g/n Wi-FiAudio codec supportNarrowband audio compression codecs: G.711a, G.711u, G.729a, G.729ab,and Internet Low Bitrate Codec (iLBC)Wideband audio compression codecs: G.722, Internet Speech Audio Codec(iSAC), iLBC, and AAC-LD audio compression codecs.Operating SystemAndroid 4.1.1 (Jellybean)ProcessorCisco DX70: TI OMAP 4470 1.5GHz dual-core ARM Cortex-A9 processorCisco DX80: TI OMAP 4470 1.5GHz dual-core ARM Cortex-A9 processorCisco DX650: TI OMAP 4460 1.5-GHz dual-core ARM Cortex-A9processorMemory2-GB RAM; Low Power Double Data Rate Synchronous DynamicRandom-Access Memory (LPDDR2 SDRAM)Storage8-GB eMMC NAND Flash memory (embedded multimedia card;nonvolatile)Network and Computer Port PinoutsCisco DX Series devices include network and computer (access) ports, which are used for network connectivity.They serve different purposes and have different port pinouts.Cisco DX Series Administration Guide, Release 10.2(5)4
Technical SpecificationsNetwork Port Connector Pinouts The network port is the 10/100/1000 SW port. The computer (access) port is the 10/100/1000 PC port.Network Port Connector PinoutsTable 3: Network Port Connector PinoutsPin NumberFunction1BI DA 2BI DA-3BI DB 4BI DC 5BI DC-6BI DB-7BI DD 8BI DD-BI stands for bidirectional, while DA, DB, DC and DD stand for Data A, Data B, Data C and Data D,respectively.Computer Port Connector PinoutsTable 4: Computer (Access) Port Connector PinoutsPin NumberFunction1BI DB 2BI DB-3BI DA 4BI DD 5BI DD-6BI DA-Cisco DX Series Administration Guide, Release 10.2(5)5
Technical SpecificationsPorts Used by Cisco DX Series DevicesPin NumberFunction7BI DC 8BI DC-NoteBI stands for bidirectional, while DA, DB, DC and DD stand for Data A, Data B, Data C and DataD, respectively.Ports Used by Cisco DX Series DevicesThe following table describes the ports that Cisco DX Series devices use. For additional information, see theTCP and UDP Port Usage Guide for Cisco Unified Communications Manager.Table 5: Cisco DX Series Device PortsSource PortRemote DevicePortUnderlyingProtocolProtocol/Service Notes6867-DHCP clientDHCP support to obtain dynamicIP addresses49152-5324853UDPDNS clientDNS support for name resolution49152-5324869UDPTFTP clientTFTP support is required to obtainvarious configuration and imagefiles from a central server.49152-5324880TCP/UDPHTTP client80ServerconfiguredTCP/UDPHTTP server123123UDPNTP client49152-53248ServerconfiguredTCPHTTP client49152-532486970TCPTFTP clientTFTP support is required to obtainvarious configuration and imagefiles from a central server.49152-532485060TCPSIP/TCPDefault is 5060; administrator canchange.49152-532485061TCPSIP/TLSDefault is 5061; administrator canchange.Cisco DX Series Administration Guide, Release 10.2(5)6Network Time Protocol to obtaintime-of-day
Technical SpecificationsNetwork ProtocolsSource PortRemote DevicePortUnderlyingProtocolProtocol/Service Notes16384- 32767Receiver RangeUDPRTPAdministrator can configure portrange.16384- 32767Receiver RangeUDPRTCPRTCP port is RTP 1.4224PC DynamicRangeTCP22ServerconfiguredTCPSecure shell4051TCPLoad upgrades4052RDPLoad upgrades4061Special debugs8443Contacts searchNetwork ProtocolsCisco DX Series devices support several industry-standard and Cisco network protocols that are required forvoice communication. The following table provides an overview of the network protocols that the devicessupport.Table 6: Supported Network ProtocolsNetwork ProtocolPurposeUsage NotesBinary Floor Control Protocol(BFCP)BFCP allows users to share a presentation within an ongoing BFCP is automatically enabled.video conversation.BluetoothBluetooth is a wireless personal area network (WPAN)The devices support Bluetooth 3.0.protocol that specifies how devices communicate over short The devices support Hands-Freedistances.Profile (HFP), Advanced AudioDistribution (A2DP) Profile,Human Interface Device Profile(HID), Object Push Profile (OPP),and Phone Book Access Profile(PBAP).Bootstrap Protocol (BootP)BootP enables a network device to discover certain startupinformation, such as the IP address.—Cisco DX Series Administration Guide, Release 10.2(5)7
Technical SpecificationsNetwork ProtocolsNetwork ProtocolPurposeCisco Discovery Protocol (CDP) CDP is a device-discovery protocol that runs on allCisco-manufactured equipment.Using CDP, a device can advertise its existence to otherdevices and receive information about other devices in thenetwork.Usage NotesThe device uses CDP tocommunicate information, such asauxiliary VLAN ID, per-portpower management details, andQuality of Service (QoS)configuration information, with theCisco Catalyst switch.Cisco Peer-to-Peer Distribution CPPDP is a Cisco proprietary protocol that is used to form a The Peer Firmware Sharing featureProtocol (CPPDP)peer-to-peer hierarchy of devices. This hierarchy is used to uses CPPDP.distribute firmware files from peer devices to theirneighboring devices.Dynamic Host ConfigurationProtocol (DHCP)DHCP dynamically allocates and assigns an IP address tonetwork devices.DHCP is enabled by default. If itis disabled, you must manuallyDHCP enables you to connect a device into the network and configure the IP address, subnetmask, gateway, and a TFTP serverfor that device to become operational without the need toon each device locally.manually assign an IP address or to configure additionalnetwork parameters.Cisco recommends that you useDHCP custom option 150. Withthis method, you configure theTFTP server IP address as theoption value. For additionalsupported DHCP configurations,see the “Dynamic HostConfiguration Protocol” chapterand the “Cisco TFTP” chapter inthe Cisco Unified CommunicationsManager System Guide.NoteIf you cannot use option150, you may try usingDHCP option 66.Hypertext Transfer Protocol(HTTP)HTTP is the standard way of transferring information andmoving documents across the Internet and the web.Hypertext Transfer ProtocolSecure (HTTPS)Hypertext Transfer Protocol Secure (HTTPS) is a combination Web applications with both HTTPof the Hypertext Transfer Protocol with the SSL/TLS protocol and HTTPS support have twoto provide encryption and secure identification of servers.URLs configured.
Cisco DX Series Administration Guide, Release 10.2(5) First Published: December09,2015 Last Modified: February08,2016 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive . ExtensionMobilityMulti-User 102 SetUpCiscoExtensionMobility 103 CiscoMobility 104 Conference 104 SecureConference 104 Divert 104 DoNotDisturb 105 .
Cisco ASA 5505 Cisco ASA 5505SP Cisco ASA 5510 Cisco ASA 5510SP Cisco ASA 5520 Cisco ASA 5520 VPN Cisco ASA 5540 Cisco ASA 5540 VPN Premium Cisco ASA 5540 VPN Cisco ASA 5550 Cisco ASA 5580-20 Cisco ASA 5580-40 Cisco ASA 5585-X Cisco ASA w/ AIP-SSM Cisco ASA w/ CSC-SSM Cisco C7600 Ser
Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unified Computing System (Cisco UCS), Cisco UCS B-Series Blade Servers, Cisco UCS C-Series Rack Servers, Cisco UCS S-Series Storage Servers, Cisco UCS Manager, Cisco UCS
Cisco Nexus 1000V Cisco Nexus 1010 Cisco Nexus 4000 Cisco MDS 9100 Series Cisco Nexus 5000 Cisco Nexus 2000 Cisco Nexus 6000 Cisco MDS 9250i Multiservice Switch Cisco MDS 9700 Series Cisco Nexus 7000/7700 Cisco Nexus 3500 and 3000 CISCO NX-OS: From Hypervisor to Core CISCO DCNM: Single
Sep 11, 2017 · Note: Refer to the Getting Started with Cisco Commerce User Guide for detailed information on how to use common utilities for a record in Cisco Commerce. See Cisco Commerce Estimates and Configurations User Guide for more information.File Size: 664KBPage Count: 5Explore furtherSolved: Cisco Serial Number Lookups - Cisco Communitycommunity.cisco.comHow to view and/or update your CCO profilewww.cisco.comSolved: How do I associate a contract to my Cisco.com .community.cisco.comHow do I find my Cisco Contract Number? - Ciscowww.cisco.comPower calculator tool - Cisco Communitycommunity.cisco.comRecommended to you b
Apr 05, 2017 · Cisco 4G LTE and Cisco 4G LTE-Advanced Network Interface Module Installation Guide Table 1 Cisco 4G LTE NIM and Cisco 4G LTE-Advanced NIM SKUs Cisco 4G LTE NIM and Cisco 4G LTE-Advanced NIM SKUs Description Mode Operating Region Band NIM-4G-LTE-LA Cisco 4G LTE NIM module (LTE 2.5) for LATAM/APAC carriers. This SKU is File Size: 2MBPage Count: 18Explore furtherCisco 4G LTE Software Configuration Guide - GfK Etilizecontent.etilize.comSolved: 4G LTE Configuration - Cisco Communitycommunity.cisco.comCisco 4G LTE Software Configuration Guide - Ciscowww.cisco.comCisco 4G LTE-Advanced Configurationwww.cisco.com4G LTE Configuration - Cisco Communitycommunity.cisco.comRecommended to you b
Supported Devices - Cisco SiSi NetFlow supported Cisco devices Cisco Catalyst 3560 Cisco 800 Cisco 7200 Cisco Catalyst 3750 Cisco 1800 Cisco 7600 Cisco Catalyst 4500 Cisco 1900 Cisco 12000 Cisco Catalyst 6500 Cisco 2800 Cisco ASR se
Cisco Nexus 7706 Cisco ASR1001 . Cisco ISR 4431 Cisco Firepower 1010 Cisco Firepower 1140 Cisco Firepower 2110 Cisco Firepower 2130 Cisco FMC 1600 Cisco MDS 91485 Cisco Catalyst 3750X Cisco Catalyst 3850 Cisco Catalyst 4507 Cisco 5500 Wireless Controllers Cisco Aironet Access Points .
Cisco 2951 2 2 Cisco 3925 4 4 Cisco 3945 4 4 Cisco 3925E 3 3 Cisco 3945E 3 3 Cisco 1841 1 1 Cisco 2801 2 1 Cisco 2811 2 1 Cisco 2821 2 1 Cisco 2851 2 1 Cisco 3825 4 2 Cisco 3845 4 4 Table 1A provides relevant software information Router Chassis Software Release Minimum Software Package Cisco 1921 15.0(1)M2 IP Base
