Assembly Instructions 2 People 70 Mins ITEM # HIK 94
HODEDAHAssembly Instructions2 peopleThis instruction booklet contains important safety information, please read and keep for future reference.70 minsITEM # HIK 941 YR LTDKITCHEN CABINET1 BoxFRONT VIEWREAR VIEWProduct Dimensions : Height 70.9'' x Width 23.6'' x Depth 15.75''1 Pagewww.Hodedah.com
HODEDAHQuestions, need parts, we are here to help!PhoneEmailWebsiteMon - Fri 9:30am to 5pm ESTSend us an emailVisit our website to open a case1 - 855 - HODEDAHSupport@Hodedah.comwww. Hodedah.com1 - 855 - 463 - 3324FOR PROMPT, RELIABLE SERVICE PLEASE HAVE YOUR INSTRUCTION MANUAL READYDO NOT RETURN PRODUCT TO THE STOREIf parts are missing or damaged please contact our customer service team and we willgladly ship your replacement parts FREE of charge within ONE YEAR of purchase!WARRANTYHodedah warrants this product to be free from defect in materials and workmanship and agrees to remedy and such defect.This warranty covers one year from the date of original purchase. This is solely limited to replacement of defective parts and noassembly for labor is included. This warranty does not apply to any product that has been improperly assembled, subjected tomisuse, abuse or which has been altered or repaired in any way. To obtain warranty service, original purchaser must present thefollowing; original bill of sale, date of purchase, where the product was purchased and images if applicable. Components replacedwarranted through the remainder of the original warranty only. The defective part will be replaced without charge, subject to theterms and conditions described above.WARNINGThis product contains small parts, keep away from children.This product contains plastic bags, keep away from children.Serious or fatal crushing injuries can occur from furniture tip-over. To help prevent this,place heaviest items on the lower shelves and drawers. Do not set heavy object on topshelves and drawers.Never allow children to climb or hang on drawers, shelves and doors.Never open more than one drawer at a time.The use of tip-over restraints may reduce but not eliminate the risk of tip-over.2 Pagewww.Hodedah.com
HODEDAHLet's get started.Helpful hints, read before beginning assemblyMake sure you receive all boxes. if your item is packed in one box, box count will read 1of 1, likewise if your item is packed in two boxes, box count will read 1 of 2 and secondbox will read 2 of 2.Read each step carefully. It is very important that each step is performed in the correctorder. If these steps are not followed in sequence, assembly difficulties will occur.Work in a spacious level area, preferably carpet, near the place the unit will be used.DO NO USE power tools to assemble your furniture, it will strip and damage parts.Your package should include the following hardware and parts. Parts are labeled orstamped on the raw edge. Please inspect contents to ensure you have received allcomponents. If you are missing any hardware or parts please contact customerservice right away before assembly.Assembly Tools Required (not supplied)5mHammerPhilips ScrewdriverTape MeasureNo Power Tools NeededProduct Care and MaintenanceWipe clean with dry soft cloth, never use chemicals or cleaning products they willdamage the finish.Avoid placing your furniture in direct sunlight, as sunlight causes fading.Never push, drag or pull your furniture, to move to a new location carefully with two ormore people carry the unit to its new location.Avoid extreme changes in temperature by arranging furniture away from radiators, heatand air vents and air conditioning units.3 Pagewww.Hodedah.com
HODEDAHHardware ListAQTYD22PcsQTYM8X25MMM4X20MMBM6X50MMHMinifix BoltG316PcsIAllen KeyHinges 5/84PcsLDoorSupport Spring4PcsN1Metal PieceONail 5/846PcsShelf Support4PcsMoonHandle 96mmM5PcsN22PcsQTYMinifix Cap16PcsJ1PcsKM4X38MM8Pcs2PcsG2Minifix 5kgMagnet (1 Hole)N32PcsPMirror Bracket2 Pin Stopper1PcsM3X12MM2PcsPVC Leg4PcsQ12PcsImportant1. Before you throw the package, please use the Check Box to identify the parts and hardware to ensure that you haveeverything you need.2. Check and measure the bolts before applying them to parts.3. Do not completely tighten all hardware until the entire assembly is complete, unless indicated otherwise.4 Pagewww.Hodedah.com
HODEDAHHardware ListQTYR1R22Drawer Slide ''14 Pcs2Drawer Slide ''14 PcsImportant1. Before you throw the package, please use the Check Box to identify the parts and hardware to ensure that you haveeverything you need.2. Check and measure the bolts before applying them to parts.3. Do not completely tighten all hardware until the entire assembly is complete, unless indicated otherwise.5 Pagewww.Hodedah.com
HODEDAHParts List1QTY1686x380x15mm Pcs2528x76x15mmQTY3QTY1Pcs1686x380x15mm Pcs4561562x396x15mm Pcs1600x396x15mm Pcs1710x558x2.5mm Pcs78911002x292x15mm Pcs1528x292x15mm Pcs11002x292x15mm Pcs1011121600x324x15mm Pcs11024x558x2.5mm Pcs1528x278x15mm Pcs1314151476x274x15mm Pcs1476x274x15mm Pcs400x176x3mm1617181472x111x15mm Pcs2343x121x15mm Pcs1501x343x2.5mm Pcs2Pcs6 Pagewww.Hodedah.com
HODEDAHParts List19QTY1522x192x15mm Pcs20QTY1466x258x15mm Pcs21QTY1466x258x15mm Pcs7 Pagewww.Hodedah.com
HODEDAHThe Breakdown.II) Door & Drawer :I) Main Unit :13101412815157119161751921861712032148 Pagewww.Hodedah.com
HODEDAHStep 1A22WOOD DOWEL M8x25MMG216MINIFIX BOLT179382105BOTTOM VIEWTOP VIEW579BOTTOM VIEW- Insert 22 x Wood Dowels A into panel (1,2,3,7,8 & 9). Using hammer to gently tap them in.- Tighten 16 x Minifix Bolt G2 into panel (5,7,9 & 10).9 Pagewww.Hodedah.com
HODEDAHStep 2CCB SCREW M3.5X16MM6JSHELF SUPPORT4DRAWER SLIDE ''142R11739RIGHT VIEWLEFT VIEW- Insert 4 x Shelf Support J onto the panel (7 & 9).- Place the Drawer Slide R1 on to 3 holes area shown at Right view side panel (1). Then tightenit with 3 x cb screws M3.5x16mm C.- Place the Drawer Slide R1 on to 3 holes area shown at Left view side panel (3). Then tightenit with 3 x cb screws M3.5x16mm C.10 Pagewww.Hodedah.com
HODEDAHStep 3CIMCB SCREW M3.5X16MM20N2HINGES 5/84P2 PIN STOPPER1153.5KG MAGNET (1 HOLE)2MIRROR BRACKET12IPCC13141314REAR VIEWREAR VIEWM102BOTTOM VIEWBOTTOM VIEW- Put 12 x bracket (P) onto Glass (15), then tighten 12 x cb screws M3.5x16mm C. Throughbracket (P) thru hole.- Put 4 x slot hinges I into upper door panel (13 & 14) non-thru. Holes as shown, then tighten8 x cb screws M3.5x16mm C through hinges I thru hole.- Insert 2 x Pin Stopper M onto panel (10) 's non thru.- Insert 2 x magnet N2 onto panel (2) 's non-thru holes as shown, make sure the magnets, ironside facing frontward to edging direction.11 Pagewww.Hodedah.com
HODEDAHStep 4DKLCB SCREW M4X20MMDOOR SUPPORT SPRIRGMOON HANDLE - 96MM844N1N3METAL PIECECB SCREW M3X12MM142121221522222221REAR VIEW1. Insert 4 x door support spring (K) into door panel (21 & 22) top&bottom side.2. Place 4 x handle (L) to panels (14,15,21 & 22) front. Then use 8 x screws (D) to tighten itfrom panels (14,15,21 & 22) back.3. Fix and tighten 2 x metal piece (N1) by using 2 x screws (N3) to panel (21 & 22) back.12 Pagewww.Hodedah.com
HODEDAHStep 5CEFCB SCREW M3.5X16MMCB SCREW M4X32MMCB SCREW M4X38MM628LOR2MOON HANDLE - 96MMNAIL 5/8DRAWER SLIDE ''141102COMPLETED1. Place 2 x panels (18) next to each side of panel (20 & 17). (As Shown). Then tightenscrews (F) from the side of panels (18) with screwdriver.2. Flip drawer bottom side up, take panel (19) and using nails (E) slight hammer nailsinto the edges thru panel (19) onto panel (20 # Drawer front) and (17 # Drawer back).3. Then place drawer slide (R2) onto the edges of panels (18) both sides and screw inthree Letter (C) screws onto each hole of the drawer slide connecting it to panels (18)with screwdriver. (As Shown).4. Flip drawer around and attach handle (L) to front panel (20) by using 2 x screws (E)from the inner side panel (20) with screwdriver.13 Pagewww.Hodedah.com
HODEDAHStep 6BCSK CAP WOOD M6X50MM2HALLEN KEYB1H2131. Fix panel (2) to panel (1 & 3) by inserting dowels (A) onto non-thru holes at panel(1 & 3). Then tighten 2 x csk M6x50mm (B) to panel (2) from the thru-holes of panel(1 & 3).14 Pagewww.Hodedah.com
HODEDAHStep 5CEFCB SCREW M3.5X16MMCB SCREW M4X32MMCB SCREW M4X38MM628LOR2MOON HANDLE - 96MMNAIL 5/8DRAWER SLIDE ''141102COMPLETED- Place 2 panel (17) on each side of panel (19) as shown.- Then, tighten screw (F) to panel (16) lower thru holes to fix them onto panel (17).- Next tighten screw (F) to panel (17) upper thru holes to fix up to the panel (19).- Flip drawer with bottom side up, place panel (17) onto the drawer and align properly.Then nail the nails provided with hammer on the border of panel (18) as shown. Thegap(18)(angle)(C) oneach drawer slide (R2) as shown.Tighten 2 screw (E) from inner side of panel (19) into the handle (L) holes.13 Pagewww.Hodedah.com
HODEDAHStep 8CCB SCREW M3.5X16MM16QPVC LEG4QC21431. Fix 4 x leg (Q) onto panel (4)'s 4 side edges by using 16 x screws (C) with screwdriverto tighten it.16 Pagewww.Hodedah.com
HODEDAHStep 9G1G344MINIFIX NUTMINIFIX CAPHALLEN KEY1521431. Fix panel (5) to panel (1 & 3) by inserting dowel (A) onto non-thru holes at panel (5).Then insert 4 x minifix nut (G1) into panel (1 & 3) 's L-thru holes and using allen key (H)to tighten it. After that insert 4 x cap (G3).17 Pagewww.Hodedah.com
HODEDAHPART 118 Pagewww.Hodedah.com
HODEDAHSTEP 10G1G3MINIFIX NUTMINIFIX CAP744HALLEN KEY1891. Fix panel (8) to panel (7 & 9) by inserting dowels (A) onto non-thru holes at panel (7 &9). Then insert 4 x minifix nut (G1) onto non-thru holes at panel (8) with allen key (H).After that, insert 4 x cap (G3).19 Pagewww.Hodedah.com
HODEDAHSTEP 11G1G3MINIFIX NUTMINIFIX CAP44HALLEN KEY11071091. Fix panel (10) to panel (7 & 9) by inserting dowels (A) onto non-thru holes at panel(10). Then insert 4 x minifix nut (G1) into panel (7 & 9) 's L-thru holes with allen key (H)to tighten it. After that insert 4 x cap (G3).20 Pagewww.Hodedah.com
HODEDAHPART 221 Pagewww.Hodedah.com
HODEDAHSTEP 12G1G3MINIFIX NUTMINIFIX CAP44HALLEN KEY7195131. Fix panel (7 & 9) to panel (5) by inserting dowel (A) onto non-thru holes at panel (5).Then insert 4 x minifix nut (G1) into panel (7 & 9) 's L-thru holes with allen key (H)to tighten it. After that insert 4 x cap (G3).22 Pagewww.Hodedah.com
HODEDAHSTEP 13ONAIL 5/8361091163- At face back position, place back panel (6 &12) onto the back of the main unit, andalign it properly for nailing. Use hammer to nail the nails one by one on the line drawnand at center of 4 side edges. Gap between 2 nails should be about 55mm for all.23 Pagewww.Hodedah.com
HODEDAHSTEP 14121913- Take panel (12) and place it inside the top compartment by putting it on the 4 shelfsupport as shown. Put in the drawer by slotting the rollers at each and of drawer slideR2 onto the rail of drawer slide R1 fixed at side panel (1 & 3), Then push the drawerin slowly.24 Pagewww.Hodedah.com
HODEDAHStep 15Final step.C8CB SCREW M3.5X16MMICrootdjus tAd & ouin1314Adjusleft t door&right2021- Fix upper door panel (13 & 14) by Hinges I and tighten 8 x cb screws M3.5x16mm Cthrough Hinges (I) thru hole.- Fix down door panel (20 & 21) by pushing and slotting the Door Support Spring K ontoeach holes at bottom of panel (4) and middle support (2).25 Pagewww.Hodedah.com
HODEDAHJob Complete.Enjoy & Thank you for purchasing from Hodedah!26 Pagewww.Hodedah.com
HODEDAHInstallation of Anti-Tip RestraintKit includes:A (x2)Long screwC (x2)Restraint strapB (x4)Mounting bracketD (x2)Short screwSerious of fatal crushing injuries can occurfrom furniture tip-over. To help Prevent tip-over:Install tip-over restraint providedPlace heaviest items in the lower drawersDo not set TV's or other heavy objectS on top of this productNever allow children to climb or hang on drawers, doors orshelvesNever open more than one drawer at a timeDo not defeat or remove the drawer interlock systemUse tip-over restraints may only reduce but not eliminate therisk of tip-over.IMPORTANT: Use of this safety kit is mandatory. This restraint is not a substitute for properadult supervision. Failure to detach this restraint before moving furniture may result in injuryand damage. If the safety kit is not in the box, please contact our consumer service team atTel. 1 (718) 456 0505 or Email Support@Hodedah.com in order to obtain one before usingthe furniture.27 Pagewww.Hodedah.com
HODEDAHFITTING OF ANTI-TIP SAFETY STRAPbSTEP 1:dAttach the mounting bracket b to the furniture in thesolid part below the top panel a few inches away from theside of the unit.Screwdbthrough the smallest hole ofbSTEP 2:Locate a stud inbehind thehave toaBACK SIDE OFTOP PANEL.Place the other mountingbracket b on the wallstud 2 inches below themounting bracketsecured to the back ofyour unit.cAttach to the wall studusing c through thesmaller hole of b .WALLFURNITURESTEP 3:Repeat the same step a few inches away fromthe other side of the unit.Place the furniture into position so both mountingbrackets are vertically in line.Lace the end of the restraint strap through thelarger holes in each mounting bracket.Secure the straps and lock into place.aTP 8#x2'' Screw2 Pcs.bMounting bracket4 Pcs.cRestraint strap2 Pcs.dTP 6#x5/8'' Screw2 Pcs.28 Pagewww.Hodedah.com
C CB SCREW M3.5X16MM 6 HODEDAH www.Hodedah.com Step 5 13 Page E CB SCREW M4X32MM 2 F CB SCREW M4X38MM 8 L MOON HANDLE - 96MM 1 R2 NAIL 5/8 10 - Place 2 panel (17) on each side of panel (19) as shown. - Then, tighten screw (F) to panel (16) lower thru holes to fix them onto panel (17).
Top Level Bill of Materials UNC Charlotte Senior Design Project: Scooter Project Bill of Materials for End Project 10/06/2006, Rev A Item Qty Price per Total Source Handle Bar Assembly 1 3.39 3.39 Sub-Assembly Steering Assembly 1 6.29 6.29 Sub-Assembly Frame Assembly 1 7.79 7.79 Sub-Assembly Front Wheel Assembly 1 6.15 6.15 Sub-Assembly
sc500 53 b nil 2015.05.19 2015.02.13 pos. artikel-nr. menge variante notes 1 9100000735 1 decals nilfisk sc500 kit 2 1 wheels rear-squeegee assembly [1] 3 1 tank recovery assembly [2] 4 1 motor drive assembly [3] 5 1 tank solution assembly [4] 6 1 squeegee assembly [5] 7 1 paddle assembly [6] 8 1 panel control assembly [7] 9 1 deck brush .
x86 Assembly Language Introduction. x86 Assembly Why Learn Assembly? Assembly is the most primitive tool in the programmers toolbox. Entire software projects can be written without ever once looking at a single line of assembly code. So the question arises: why learn assembly?
AB-103 Assembly Guide page 10 2 Assembly Instructions Assembly Instructions Assembly of the AB-103 takes about 30 minutes to complete. If this is the first time you have assembled this type of equipment, plan on allowing more time. Be careful to open the box and assemble components in the sequence presented in this manual.
What is Assembly Language? Low-level programming language for a computer One-to-one correspondence with the machine instructions Assembly language is specific to a given processor Assembler: converts assembly program into machine code Assembly language uses: Mnemonics: to represent the names of low-level machine instructions
: New Parts RANK: Japan only * * * * * * * * * * * * * * * * * * * * * * * * * * * * * OVERALL ASSEMBLY SGV800 A01 Neck Assembly BUS A01 Neck Assembly RDS A01 Neck Assembly BKS A01 Neck Assembly PSW A01a Seal (QC55400) D01 Body E01 Tuning Machine Assembly SPERZEL TUNER 0.87 6 10 E03 Mark yamaha logo (QC32010) E10 Rod Cover BL 04 E11 Oval Head .
Parts Catalogue BRANSON TRACTOR. CONTENTS C001 Mounting Kit 3 C002 Main Frame Assembly 5 C003 Swing Frame Assembly 7 C004 Boom Lower Assembly 9 C005 Boom High Assembly 11 C006 Bucket Assembly- STD. 13” HD 13 C007 Bucket Assembly- Option. 16”HD 15 C008 Hydraulic Parts(for S/N. K50911) 17 C009 Hydraulic Parts(for S/N.L50960 ) 19 C010 Cylinder(BH76C-09-8100) 21 C011 Cylinder(BH76C-09-830A .
S What is Generative Assembly Structural Analysis (3/5) We have two basic approaches to perform Generative Assembly Structural analysis – Assembly Analysis and Analysis Assembly Assembly Analysis: A. The product document is available. You will switch to analysis workbench to create
