IPSCO STS (Short Throw Shifter) Installation Instructions .
IPSCO STS (Short Throw Shifter) Installation Instructions2003-2010 Dodge ViperWARNINGModification of your vehicle with the parts identified above mayalter its stock performance; the buyer hereby expressly assumesall risks associated with any such modification.DISCLAIMER OF WARRANTYSeller disclaims any warranty express or implied with respect tothe parts sold hereby whether as to merchantability, fitness forparticular purpose, or any other matter. IPSCO assumes noliability expressed or implied for the improper installation or useof this product or its components. IPSCO is NOT responsible forany damage, consequential or otherwise for equipment failureafter installation.www.ipsco.org – Elizabeth, Colorado – 303-252-4481Page 1
IPSCO STS (Short Throw Shifter) Installation Instructions2003-2010 Dodge ViperParts:IPSCO STS (Short Throw Shifter)shifter cover mounting bolts (4)push-in nylon rivets (8)3/4" plastic plugs (2)Loctite RTV SiliconeTools:Phillips head screw driver (medium)plastic pry tool3/4" open end wrench or crescent wrench17mm open end wrench or crescent wrenchsocket ratchet6" or 8" socket extensionuniversal joint13mm socket3/16" Allen wrenchdrill1/4" drill bit3/4" drill bit or step drill bitvise gripshammerpunchsmall pry barSupplies:razor bladegreaseRed or Blue Loctitewww.ipsco.org – Elizabeth, Colorado – 303-252-4481Page 2
IPSCO STS (Short Throw Shifter) Installation Instructions2003-2010 Dodge ViperInstallation Instructions:1Remove console shifter bezelRaise the parking brake handle to its most upright positionRemove the 6 socket head cap screws from the bezel ring using a 3/16" Allen wrenchwww.ipsco.org – Elizabeth, Colorado – 303-252-4481Page 3
IPSCO STS (Short Throw Shifter) Installation Instructions2003-2010 Dodge ViperInvert the upper shift boot towards the shift knob to gain access to the retaining nutPlace the 3/4" wrench on the retaining nut and the 17mm" (for OE shift knob) on the bottom ofthe shift knobTurn the upper wrench counter-clockwise to loosen the bondUnscrew the shift knob with the upper shift boot attachedwww.ipsco.org – Elizabeth, Colorado – 303-252-4481Page 4
IPSCO STS (Short Throw Shifter) Installation Instructions2003-2010 Dodge ViperCut the tie wrap holding the lower shift boot to the isolatorUse the pry tool to remove the console shifter bezelwww.ipsco.org – Elizabeth, Colorado – 303-252-4481Page 5
IPSCO STS (Short Throw Shifter) Installation Instructions2003-2010 Dodge ViperOnce the bezel has been pulled away, disconnect the electrical connectionsMark the widow switches L (left) and R (right)Disconnect the window switches and the accessory power outletLift the rear of the console shifter bezel; passing the parking brake handle through its bootwww.ipsco.org – Elizabeth, Colorado – 303-252-4481Page 6
IPSCO STS (Short Throw Shifter) Installation Instructions2003-2010 Dodge Viper2Remove the center consoleRemove the 2 forward screwsMove both seats to their most forward positionPosition both seatbacks to their most forward positionwww.ipsco.org – Elizabeth, Colorado – 303-252-4481Page 7
IPSCO STS (Short Throw Shifter) Installation Instructions2003-2010 Dodge ViperRemove the 2 rear screws (have large flat washer and are slightly larger than the forwardscrews)Remove the 4 screws inside the console box (do not remove the 4 torx screws)www.ipsco.org – Elizabeth, Colorado – 303-252-4481Page 8
IPSCO STS (Short Throw Shifter) Installation Instructions2003-2010 Dodge ViperPull the bottom of the rear bulkhead forward to release the rear of the center consoleCarefully pull out the front ears of the center console around the center instrument panel bezelwww.ipsco.org – Elizabeth, Colorado – 303-252-4481Page 9
IPSCO STS (Short Throw Shifter) Installation Instructions2003-2010 Dodge ViperLift the front of the center console over the parking brake and pull the rear away from the rearbulkheadDisconnect the rear accessory power outlet at the connection point (12" down the wire)Lift the front of the center console up over the dashRemove the center consolewww.ipsco.org – Elizabeth, Colorado – 303-252-4481Page 10
IPSCO STS (Short Throw Shifter) Installation Instructions2003-2010 Dodge Viper3Remove the lower shift bootDisconnect the wiring bundle from its post and move it towards the passenger sideDisconnect the clip holding the accessory power outlet connector to the lower section of thecenter instrument panel bezel and move it towards the passenger sidewww.ipsco.org – Elizabeth, Colorado – 303-252-4481Page 11
IPSCO STS (Short Throw Shifter) Installation Instructions2003-2010 Dodge ViperDrill out the rivets (8) using a 1/4" bitThe rivets will want to rotate while drilling them out, use vise grips to keep the rivets fromturning to minimize the damage to the lower shift bootPull the boot away from the isolatorwww.ipsco.org – Elizabeth, Colorado – 303-252-4481Page 12
IPSCO STS (Short Throw Shifter) Installation Instructions2003-2010 Dodge Viper4Remove the original shifter2 of the shifter cover mounting bolts aren't easily accessibleThey can be removed by drilling access holes just above them in the transmission tunnelwww.ipsco.org – Elizabeth, Colorado – 303-252-4481Page 13
IPSCO STS (Short Throw Shifter) Installation Instructions2003-2010 Dodge ViperMark the 2 spots on top of the transmission tunnelVisually inspect where the marked spots are making sure they are above the 2 shifter covermounting boltsUse a hammer and punch in both marked spots to make an indention so that the drill bit won'ttravelDrill the pilot holes in the transmission tunnel using a 1/4" bitwww.ipsco.org – Elizabeth, Colorado – 303-252-4481Page 14
IPSCO STS (Short Throw Shifter) Installation Instructions2003-2010 Dodge ViperDrill the final holes in the transmission tunnel using a 3/4" bit (or a step bit)Remove the 4 shifter cover mounting bolts holding the shifter with a socket ratchet, 13mmsocket, extension and universal jointwww.ipsco.org – Elizabeth, Colorado – 303-252-4481Page 15
IPSCO STS (Short Throw Shifter) Installation Instructions2003-2010 Dodge ViperPush aside the connector that is kept down by the forward passenger side cover mounting boltUse the small pry bar to break the original shifter away from the transmission tail shifter housingLift the original shifter up and away from the transmission tail shifter housing and slip it thoughthe openingwww.ipsco.org – Elizabeth, Colorado – 303-252-4481Page 16
IPSCO STS (Short Throw Shifter) Installation Instructions2003-2010 Dodge ViperRemove the gasket material from the shifter mating surface on the transmission tail shifterhousing with a razor bladeClean all debris out of the transmission tail shifter housingwww.ipsco.org – Elizabeth, Colorado – 303-252-4481Page 17
IPSCO STS (Short Throw Shifter) Installation Instructions2003-2010 Dodge Viper5Install the IPSCO STSApply grease to the STS shifter stem ballApply Loctite RTV silicone (supplied) to the outer mating surface on the STSPlace the STS into the transmission tunnel and position it over the transmission tail shifterhousingwww.ipsco.org – Elizabeth, Colorado – 303-252-4481Page 18
IPSCO STS (Short Throw Shifter) Installation Instructions2003-2010 Dodge ViperInsert the shifter stem ball of the STS into the transmission shifter receiverwww.ipsco.org – Elizabeth, Colorado – 303-252-4481Page 19
IPSCO STS (Short Throw Shifter) Installation Instructions2003-2010 Dodge ViperAlign the 4 holes and apply a small drop of Red or Blue Loctite to the threads of the new shiftercover mounting bolts (supplied)Insert the new shifter cover mounting bolts into each cornerStart with the 2 easily accessible corners (driver side)Make sure to reattach the connector on the forward passenger side cover mounting boltThe connector installs on top of the STS housingTorque each shifter cover mounting bolt to 13 ft/lbs*Note: An IPSCO 1" lowering kit was also installed during this installation*www.ipsco.org – Elizabeth, Colorado – 303-252-4481Page 20
IPSCO STS (Short Throw Shifter) Installation Instructions2003-2010 Dodge Viper6Test the STSScrew the shift knob onto the STS shifter handleWork through the gears to ensure the STS is installed correctlyRemove the shift knob from the STS shifter handle7Install the lower shift bootApply Loctite RTV Silicone (supplied) to the mating surface on the bottom of the lower shift bootPlace the lower shift boot over the STS shifter handleAttach the lower shift boot using the supplied push-in nylon rivets (supplied)Position the boot opening around the isolator of the OE shifter shaft (in this case, the lower shiftboot 1” lowering kit collar; use the tie wrap (supplied with that kit) to tighten the boot to thelower shift boot collar)Insert the plastic plugs (supplied) into the 2 drilled access holesConnect the wiring bundle to its postConnect the clip holding the accessory power outlet connector back to the lower section of thecenter instrument panel bezel8Install the center consoleInsert the rear section of the center console under the rear bulkheadConnect the rear accessory power outlet connectorPosition the center console so that the parking brake handle will pass through its openingCarefully pull out the front ears of the center console and position it back in place around thecenter instrument panel bezelwww.ipsco.org – Elizabeth, Colorado – 303-252-4481Page 21
IPSCO STS (Short Throw Shifter) Installation Instructions2003-2010 Dodge ViperAttach the center console with the 2 forward screws, 2 rear screws and 4 console box screwswww.ipsco.org – Elizabeth, Colorado – 303-252-4481Page 22
IPSCO STS (Short Throw Shifter) Installation Instructions2003-2010 Dodge Viper9Install the console shifter bezelConnect the window switches and the accessory power outletRaise the parking brake handle to its most upright positionPass the parking brake through its bootPosition the console shifter bezel in placeSnap it down to the center consoleScrew the retaining nut to the desired heightScrew down the shift knob with the upper shift boot attached*Note: An aftermarket shift knob was installed during this installation.*www.ipsco.org – Elizabeth, Colorado – 303-252-4481Page 23
IPSCO STS (Short Throw Shifter) Installation Instructions2003-2010 Dodge ViperPlace the 3/4" wrench on the retaining nut and the 17mm" (for OE shift knob) on the bottom ofthe shift knobTurn the upper wrench clockwise to tightenRevert the upper shift boot to its original positionwww.ipsco.org – Elizabeth, Colorado – 303-252-4481Page 24
IPSCO STS (Short Throw Shifter) Installation Instructions2003-2010 Dodge ViperPosition the upper shift boot using its 2 alignment guide holes; the larger one on the right(passenger side) and the smaller one on the left (drivers side)Position the bezel ring over the upper shift bootAlign the bezel ring alignment guide pins to the upper shift boot alignment guide holes; largeron the right, smaller on the leftAttach the 6 socket head cap screws for the bezel ring using a 3/16" Allen wrenchwww.ipsco.org – Elizabeth, Colorado – 303-252-4481Page 25
IPSCO STS (Short Throw Shifter) Installation Instructions 2003-2010 Dodge Viper www.ipsco.org – Elizabeth, Colorado – 303-252-4481 Page 10 Lift the front of the center console over the parking brake and pull the rear away from the rear
Shifter, Short Throw, 2010-up Camaro, Manual PACKING LIST Before installation, use this checklist to make sure all necessary parts have been included. ITEM QTY CHECK PART NUMBER DESCRIPTION 1. 1 605742805P Shifter, Polished, Short Throw Retro, 10-up Camaro 2. 1 605836805 Trim Ring, Shifter Short Throw Retro, 10-up Camaro 3. 1
2010 Short Throw Shifter Kit 1310R7400 1 Shifter Assembly R15040015 1 Isolator - Shifter rear 1 Bolts - 3/8-24 x 1" Button Head Cap Screw 2 Lock Washer - 3/8" ID, Int. Tooth 2 Upper Stick - Short R15040018 1 Installation Instructions - Shifter 1310R7400IM 1 Equipment and Supplies Required 10mm wrench
Shifter, Short Throw, 2010-11 Camaro, Manual PACKING LIST Before installation, use this checklist to make sure all necessary parts have been included. ITEM QTY CHECK PART NUMBER DESCRIPTION 1. 1 605742130 Shifter, Short Throw, 10-11 Camaro 2. 2 605114055 Bushing, Shifter, 10-11 Camaro 8. 1 INSTR Instructions
2010-13 Camaro provides a more positive feel while shifting in and out of gear. The SLP knob works with the stock shifter or SLP’s short throw shifter assembly. GF80006 2010-15 manual shift knob 86.99 ea 2010-15 Short Throw 6-Speed Shifter Shifter assembly provides a classic look with 10% reduction in throw and a more positive feel while
Roush Mustang Short Throw Shifter (05-09 GT) Please read through the instructions carefully before starting this project. Take the time to get all the materials together as well as all the safety equipment. Disassembly: 1. Place shifter in neutral position. 2. Work upper part of shift boot out of shifter knob retainer groove and slide down onto .
LG Camaro short shifter Gen 5 camaro “THE MOST POWERFUL HEADERS ON THE PLANET” Brought to you by LG Motorsports 972-429-1963 Thank you for purchasing LGM’s short throw shifter for your Camaro Parts Inventory: 1. LG Short Shifter 2. Instructions Optional 1. Threaded shift knob for threaded stick versions
Steeda S550 MT-82 Tri-Ax Race Short Throw Shifter: 555-7317, 555-7318 5. Using the10"extension and 10mm socket, remove two bolts which secure rear shifter mount and bushing. Remove this bracket and bushing from the car. 6. Make sure your transmission support is secure; using an 18mm socket remove the 4 bolts
Advanced Engineering Mathematics E Kreyszig; Wiley; 2001 4. Calculus, R A Adams; Pearson; 2002. Calculus (6th Edition) E W Swokowski, M Olinick, D Pence; PWS; 1994. MT1007 Statistics in Practice Credits 20.0 Semester 2 Academic year 2019/20 Timetable 11.00 am Description This module provides an introduction to statistical reasoning, elementary but powerful statistical methodologies, and real .
