INTAKE MANIFOLD - JustAnswer
PUBLISHED: 13-FEB-20182011.0 RANGE ROVER SPORT (LS), 303-01ENGINE - V8 N/A 5.0L PETROLINTAKE MANIFOLD(G1245958)REMOVAL AND INSTALLATION30.15.02MANIFOLD- INTAKE- LH/FRONT/EACH RENEW5000 CC,AJ D- INTAKE- LH/FRONT/EACH RENEWAJ D- INTAKE- LH/FRONT/EACH RENEWAJ V8,SUPERCHARGED2.9USEDWITHINSPART(S)STEPPART NAMEQUANTITYInstallation Step 5Throttle body to intake manifold seal1Installation Step 7Intake manifold gaskets8REMOVALNOTE:
Removal steps in this procedure may contain installation details.1.Disconnect the battery ground cable.Refer to: Specifications (414-00 Battery and Charging System - GeneralInformation, Specifications).2.Refer to: Engine Cover - V8 N/A 5.0L Petrol/V8 S/C 5.0L Petrol (501-05Interior Trim and Ornamentation, Removal and Installation).3.4.
5.6.7.
8.9.CAUTIONS:Be prepared to collect escaping fluids.Before disconnecting any components, make sure the area is cleanand free from foreign material. When disconnected all openings mustbe sealed.
10.11.12.
13.14.15.
16.NOTE:Remove and discard the O-ring seal.17.18.
19.20.INSTALLATION
1.Torque: 5 Nm2.Torque: 10 Nm
3.Torque: 10 Nm4.Torque: 5 Nm5.CAUTION:A new O-ring seal is to be installed.Renew Part: Throttle body to intake manifold seal Quantity: 1 .Torque: 18 Nm
6.7.CAUTIONS:Make sure that the mating faces are clean and free of corrosion andforeign material.Install new o-ring sealsNOTE:Do not tighten at this stage.Renew Part: Intake manifold gaskets Quantity: 8 .
8.9.10.
11.Torque: 25 Nm12.Torque: 8 Nm
13.NOTES:Do not tighten at this stage.Remove and discard the blanking caps.14.Torque:Unions 21 NmBolts 8 Nm
15.Torque: 21 Nm16.17.
18.19.20.Torque: 10 Nm
21.Torque: 3.5 Nm22.Refer to: Engine Cover - V8 N/A 5.0L Petrol/V8 S/C 5.0L Petrol (501-05Interior Trim and Ornamentation, Removal and Installation).23.Connect the battery ground cable.Refer to: Specifications (414-00 Battery and Charging System - GeneralInformation, Specifications).PUBLISHED: 11-MAY-20112011.0 RANGE ROVER SPORT (LS), 501-05INTERIOR TRIM AND ORNAMENTATIONENGINE COVER - V8 N/A 5.0L PETROL/V8 S/C 5.0L PETROL(G1224253)REMOVAL AND INSTALLATIONACOUSTIC
12.30.50COVER ENGINE RENEW5000 CC,AJ V812.30.50ACOUSTICCOVER ENGINE RENEWAJ V8,NATURALLYASPIRATED12.30.50ACOUSTICCOVER ENGINE RENEWAJ WITHINSREMOVALNOTE:Removal steps in this procedure may contain installation details.
1.NOTE:Some variation in the illustrations may occur, but the essentialinformation is always correct.INSTALLATION1.To install, reverse the removal procedure.PUBLISHED: 25-NOV-20162011.0 RANGE ROVER SPORT (LS), 414-00
2011.0 RANGE ROVER SPORT (LS), 414-00BATTERY AND CHARGING SYSTEM GENERAL All Gasoline (Petrol) Models:TypeMaintenance free lead-calciumCapacity690 amps - 75 amp/hourReserve capacity150 minutes @ 25 ampsDiesel Models:TypeMaintenance free lead-calciumCapacity825 amps - 90 amp/hourReserve capacity190 minutes @ 25 ampsBattery Disconnect/ConnectCAUTION:The vehicle status and battery condition must be established before attemptingbattery disconnect/connect. Reference must be then made to the following tableto establish the relevant procedure to be followed.NOTE:If a new battery is installed, the battery monitoring system (BMS) must be resetusing Land Rover approved diagnostic equipment.Vehicle statusEngine runningBattery chargedBattery dischargedProcedureProcedure1
Vehicle powered down, locked and alarmed23Vehicle unlocked45Procedure 1Disconnect batteryConnect battery1. If possible, applyparking brake oralternatively, chockwheels1. Ensure that all electrical loads are switched OFF2. Switch off ignition2. Connect battery leads - GROUND lead last3. Wait 2 minutes forengine managementsystem to 'power down'3. Switch on ignition4. Open the hood4. Operate parking brake switch several times until parking brakewarning lamp is extinguished5. Disconnect battery GROUND lead first5. Reset electric window one-touch facility. Power window up to hardstop, release switch, reapply and hold for 1 second (relay in door willclick). One touch should now workProcedure 2Disconnect batteryConnect battery1. Unlock the vehicle and disarm the alarm usingthe 'plip' button1. Ensure that all electrical loads are switchedOFF2. Enter the vehicle, turn the ignition key toposition II, apply the parking brake or chock thewheels and then turn the ignition key to position 0.Remove the key to 'power down' the ICE system2. Connect battery leads - GROUND lead last3. Wait 2 minutes for engine management systemto 'power down'3. Switch on ignition4. Open the hood4. Operate parking brake switch several timesuntil parking brake warning lamp isextinguished5. Disconnect battery - GROUND lead first5. Reset electric window one-touch facility.Power window up to hard stop, releaseswitch, reapply and hold for 1 second (relayin door will click). One touch should now workNOTE:1. Disconnect battery - The door unlock process initialises the ICE system.
Procedure 3Disconnect batteryConnect battery1. Unlock the vehicle from the left hand front doorusing the key1. Ensure that all electrical loads are switchedOFF2. Enter the vehicle, turn the ignition key toposition II, apply the parking brake or chock thewheels and then turn the ignition key to position 0.Remove the key to 'power down' the ICE system2. Connect battery leads - GROUND lead last3. Wait 2 minutes for engine management systemto 'power down'3. Switch on ignition4. Open the hood4. Operate parking brake switch several timesuntil parking brake warning lamp isextinguished5. Disconnect battery - GROUND lead first5. Reset electric window one-touch facility.Power window up to hard stop, releaseswitch, reapply and hold for 1 second (relayin door will click). One touch should now workNOTES:1. - Disconnect battery - The door unlock process initialises the ICE system1. Connect battery - If there is insufficient capacity in the battery to disarmthe alarm, the alarm may sound on reconnection of the battery - Step 3 willdisarm the alarmProcedure 4Disconnect batteryConnect battery1. Enter the vehicle, turn the ignition key toposition II, apply the parking brake or chock thewheels and then turn the ignition key to position 0.Remove the key to 'power down' the ICE system1. Ensure that all electrical loads are switchedOFF2. Wait 2 minutes for engine management systemto 'power down'2. Connect battery leads - GROUND lead last3. Open the hood3. Switch on ignition4. Disconnect battery - GROUND lead first4. Operate parking brake switch several timesuntil parking brake warning lamp isextinguished5. Reset electric window one-touch facility.Power window up to hard stop, releaseswitch, reapply and hold for 1 second (relayin door will click). One touch should now work
Procedure 5Disconnect batteryConnect battery1. Enter the vehicle, turn the ignition key toposition II, apply the parking brake or chock thewheels and then turn the ignition key to position 0.Remove the key to 'power down' the ICE system1. Ensure that all electrical loads are switchedOFF2. Wait 2 minutes for engine management systemto 'power down'2. Connect battery leads - GROUND lead last3. Open the hood3. Switch on ignition4. Disconnect battery - GROUND lead first4. Operate parking brake switch several timesuntil parking brake warning lamp isextinguished5. Reset electric window one-touch facility.Power window up to hard stop, releaseswitch, reapply and hold for 1 second (relayin door will click). One touch should now workNOTE:1. Disconnect battery - If the remote control module (RCM) is not functioning, itwill be necessary to manually unlock the vehicle using the key.Vehicle Jump (Emergency) Starting - Using Another VehicleCARRY OUT THE FOLLOWING OPERATIONS IN THE SEQUENCE GIVEN1. Connect one end of the BLACK (-) booster cable to the GROUND (-) battery terminal of the DONORvehicle2. Connect the other end of the BLACK (-) booster cable to a good earth point e.g. unpainted metalsurface or engine mounting at least 0.5 m (20.0 in) from the battery or fuel lines on the DISABLEDvehicle3. Connect one end of the RED ( ) booster cable to the positive ( ) battery terminal of the DONORvehicle4. Connect the other end of the RED ( ) booster cable to the positive ( ) battery terminal of theDISABLED vehicle5. Start the engine of the DONOR vehicle and allow it to idle for a few minutes6. Start the engine of the DISABLED vehicle7. Allow engines of both vehicles to idle for a few minutes then switch off the engine of the DONORvehicle8. Disconnect the RED ( ) booster cable from the battery of the PREVIOUSLY DISABLED vehicle9. Disconnect the RED ( ) booster cable from the battery of the DONOR vehicle10. Disconnect the BLACK (-) booster cable from the earth point of the PREVIOUSLY DISABLED
vehicle11. Disconnect the BLACK (-) booster cable from the battery of the DONOR vehicleWARNINGS:During normal use, batteries emit explosive hydrogen gas sufficient to causesevere explosions and capable of causing serious injury - keep sparks andnaked lights away from the engine compartment.DO NOT attempt to start the disabled vehicle if it is suspected that theelectrolyte in the battery is frozen.Suitable eye protection must be worn when working in the vicinity of thebattery.Take care when working near rotating parts of the engine.Prior to attempting to start the disabled vehicle, ensure that the parking brakeis applied or suitably chock the wheels. Ensure that 'P' - PARK - AutomaticGearbox or NEUTRAL - Manual Gearbox is selected.CAUTIONS:Ensure that all electrical loads are switched OFF prior to connecting boostercables and disconnect booster cables prior to using any electrical equipment.Ensure that the battery of the DONOR vehicle is of 12 volt capacity and thatall electrical loads on the disabled vehicle are switched OFF prior to connectingbooster cables.Ensure that there is no physical contact between the donor and disabledvehicles other than the booster cables.Vehicle Jump (Emergency) Starting - Using a Slave Battery/Starting AidCARRY OUT THE FOLLOWING OPERATIONS IN THE SEQUENCE GIVEN1. Connect the end of the BLACK (-) booster cable to the ground (-) battery terminal of the vehicle2. Connect the end of the RED ( ) booster cable to the positive ( ) battery terminal of the vehicle3. Start the engine of the vehicle and allow it to idle4. Disconnect the RED ( ) booster cable from the battery terminal of the vehicle5. Disconnect the BLACK (-) booster cable from the battery terminal of the vehicle
WARNINGS:During normal use, batteries emit explosive hydrogen gas sufficient to causesevere explosions and capable of causing serious injury - keep sparks andnaked lights away from the engine compartment.DO NOT attempt to start the disabled vehicle if it is suspected that theelectrolyte in the battery is frozen.Suitable eye protection must be worn when working in the vicinity of thebattery.Take care when working near rotating parts of the engine.Prior to attempting to start the disabled vehicle, ensure that the parking brakeis applied or suitably chock the wheels. Ensure that 'P' - PARK - AutomaticGearbox or NEUTRAL - Manual Gearbox is selected.CAUTIONS:Ensure that all electrical loads are switched OFF prior to connecting boostercables and disconnect booster cables prior to using any electrical equipment.Ensure that the slave battery/starting aid are of 12 volt capacity and that allelectrical loads on the disabled vehicle are switched OFF prior to connectingbooster cables.
2011.0 range rover sport (ls), 303-01 engine - v8 n/a 5.0l petrol intake manifold (g1245958) removal and installation 30.15.02 manifold - intake - lh /front /each - renew 5000 cc, aj v8, naturally aspirated 1.1 used withins 30.15.02 manifold - intake - lh /front /each - renew aj v8, naturally aspirated 1.9 used withins 30.15.02 manifold .
Intake Manifold Flap Linkage Pair, Billet Aluminum, B7 Audi RS4 4.2L FSI The installation of your 034Motorsport Billet Aluminum Intake Manifold Flap Linkage Pair for the B7 Audi RS4 is an involved process that requires removal of the intake manifold as documented in your factory repair manual. Supplied Parts:
F. Unbolt and remove the carburetor from the manifold. 3. If the intake manifold is being changed at this time, install the new manifold according to the manifold manufacturer's directions. Installation of Street Demon Carburetor 1. Install the carburetor-mounting studs (provided) in the proper location on the intake manifold carburetor .
Remove the 5 front-most bolts from the intake manifold, and put them in a safe place. Pull the driver’s side rear bolt up approximately ½” out of it’s hole and hold it there while tipping the front of the manifold up, and pulling the manifold toward the front of the vehicle. Once the intake intake manifold is removed, turn it upside down.
motion control valves) for emissions and low speed idle quality Gen 1 intake manifolds can be used on the Gen 2 heads/engine with minor modifications to the manifold shown in Figure 2 Figure 2 Gen 1 Intake interferes with Gen 2 Head in these locations on each side. These can be removed Gen 1 Intake Manifold Gen 1 Intake Manifold ribbing
3 Big Block RAMJET service manual 1 88962724 4 Diagnostic trouble code (DTC) tool 1 12489400 5 Intake manifold, upper 1 12464484 6 Gasket, intake manifold lower to upper 4 12489372 7 Intake manifold bolt, upper to lower 8 12490255 8 Air cleaner assembly 1 12490257.
AIR INTAKE MANIFOLD REMOVAL (SECOND EDITION) David Chamberland - 928 Owners Club-----The following is a step-by-step procedure for removing the engine intake manifold on a model year 1987 or newer Porsche 928. When attempting the procedure please keep the following in mind: 1.
valve covers. Remove intake manifold bolts, and fuel rail stop bracket. Note location of fuel rail ground strap for reassembly. Remove engine coolant air bleed hose from throttle body. Remove intake manifold bolts. Remove intake manifold. NOTE: It is not necessary to open power steering system during engine removal.
Zoology Practical Manual TM.indd 9 22-03-2019 18:45:07. 12 .
