1. Introduction - Building And Construction Authority
1. IntroductionIn a survey conducted by BCA in year 2003 involvingabout 10,000 private residential units, water seepagethrough external walls was found to be a commondefect faced by homeowners. The survey findings alsoshowed that the use of single layer brickwall is themost common cause of water seepage through externalwalls. Almost 90% of the water seepage occurredthrough cracks in the plastered brickwalls. In general,water seepage through external walls occurred withinthe first five years of building completion.introduction/ design of external wallsWater seepage through the external walls isunacceptable to the occupants. The problem is furthercompounded by Singapore’s high humidity andabundant rainfall throughout the year. High windspeeds experienced by high-rise buildings alsoincrease the likelihood of water seepage. Buildingenvelopes must, therefore, be adequately designedand constructed to prevent ingress of water.There are various external wall systems used in thelocal industry, including precast concrete walls, castin-situ reinforced concrete walls, brickwalls, curtainwalls, cladding walls, concrete block walls, etc.Due to volume constraint, this publication focuses onprecast concrete walls, cast in-situ reinforced concretewalls and plastered brickwalls. It provides industrygood practices to help achieve durable and effectivewaterproofing of the building envelope.2. Design of External Walls2.1. GENERALThe ingress of rainwater impinging on external wallsusually occurs though joints and cracks in the walls.To a lesser extent, seepage through absorption andpermeation may also occur depending on the materialand thickness of the walls.Watertightness of external walls is usually achieved byusing suitable materials, providing adequate wallthickness, designing proper construction details, aswell as providing surface rendering and finishes whichserve as barrier against water ingress. Where externalwalls are exposed to severe weather conditions, moreextensive surface waterproofing should be employed.This chapter focuses on the design aspects of precastconcrete walls and plastered brickwalls.2.2. CHOICE OF EXTERNALWALL SYSTEMThe common types of external walls include cast insitu reinforced concrete (RC) walls, precast concretewalls and masonry brickwalls.Figure 2.1: Common types of external wall systemReinforced Concrete (RC) Wall1Precast Concrete WallMasonry Brickwall
Hence, the use of precast concrete walls is stronglyrecommended for external wall construction.2.3. EXTERNAL PRECAST WALLSPrecast joints are the weakest links in ensuringwatertightness of the external precast concrete walls.These include joints between precast concrete elements,between precast and cast in-situ elements, as well asbetween precast elements and window/door framesor other fittings. Joint detailing and the use of suitablesealant should, hence, be carefully considered duringthe design stage. Joints with complicated profiles aredifficult to seal and this may affect the watertightnessof the building envelope.There are two types of joint detailing employed forprecast concrete walls, namely the one-stage joint andtwo-stage joint. One-stage joint is a simple butt jointwith sealant applied against a backer rod at the externalface of the wall. One-stage joint offers only a singleline of defence against water seepage. Pressure dropmay occur across the one-stage joint and water mayseep through micro cracks or hairline cracks. Twostage joint (Figure 2.2), on the other hand, providestwo defence lines against water ingress. Experience hasshown that two stage joints give better watertightnessperformance than one-stage joints.design of external wallsWater seepage usually occurs through the fabric ofbuilding elements or through the gaps between theseelements. For effective watertightness, the wall systemshould be constructed with impervious material andwith minimal joints. Large precast concrete panelsand cast in-situ RC construction with low water cementratio, in general, have better watertightness performancethan brickwalls, which have extensive joints betweenlayers of bricks. In addition, precast walls have manyother benefits over cast in-situ concrete walls andbrickwalls, such as better quality, higher buildabilityand better durability.Figure 2.2: Two-stage joint ofing stripSealantBacker rodNon-shrink groutInfill concreteINTERNALEXTERNALTwo-stage horizontal joint (Sectional view)INTERNALTwo-stage vertical joint (Plan view)2.3.1 HORIZONTAL JOINTSFor horizontal joints of precast walls, joggled joints(as shown in Figure 2.3) provide better watertightnessperformance than the butt joints. The matchingupstand and downstand profile of the joggled jointprevents inflow of water through the building envelope.The height of the upstand and downstand is dependenton the exposure conditions, wall thickness and typeof precast wall (load-bearing or non load-bearing). Itgenerally ranges from 35mm for mild exposure to100mm for severe exposure condition.Figure 2.3 shows the typical details for a horizontaljoggled joint. The joint is sealed with high strengthnon-shrink grout and an approved self-adhesivecompressible waterproofing strip. In addition, anapproved flexible cementitious waterproofingmembrane may be used at the inner corner of theintersection between the wall panel and beam/slabfor enhanced watertightness performance.2
Figure 2.3: Typical sectional view of horizontal joggled joint (for non load-bearing walls)Precast panelApproved self-adhesivecompressible waterproofing strip[A] 35mmHigh strength non-shrink grout[B] 35mm[B][C] 1[C]design of external walls100mm15mm[B]Approved flexible cementitiouswaterproofing membrance15mmTypicalstorey level[A]100mmSlope 1:10FilletCast in-situ beamINTERNALThe gap at the external wall face is usually not sealedto allow incident water in the joint to drain off. If thisgap is also to be sealed (eg. for aesthetic reasons), thejoint can be fully sealed using non-shrink grout, witha backer rod and an appropriate sealant installed atthe exterior end of the joint (Figure 2.4a). Alternatively,the joint can be sealed with non-shrink grout at theinterior end with a sealant installed at the exterior end3EXTERNALof the joint. For such sealing system, the sealant mustbe discontinued at regular intervals (at intersectionswith the vertical joints) to drain off incident waterthat has managed to seep into the gap (Figure 2.4b).For load bearing walls, the entire horizontal jointmust be sealed, for example, with non-shrink grout(Figure 2.4a).
Figure 2.4: Typical sectional view of horizontal joggled jointJoint fully sealed withnon-shrink groutApproved self-adhesivecompressible waterproofing stripBacker rodHigh strengthnon-shrink groutBacker rodSealantSealant must bediscontinued atvertical jointsa) Fully sealed horizontal jointb) Sealing of external gap (For non load bearing walls)2.3.2 VERTICAL JOINTSdesign of external wallsand an infilled concrete/mortar joint with a sealingstrip at the inner wall face. The seal at the external faceshould be discontinued at intersections with thehorizontal joints to allow draining of incident water.The two-stage joint detailing is recommended forvertical joints as it provides various water-resistantbarriers. These include a sealant at the outer wall face,a pressure relief space to avoid rain driven penetration,Figure 2.5: Vertical joint sealed with sealant and infill concrete/mortar joint, with pressure relief space (plan view)EXTERNAL15mmSealant 50mmBacker rodPressure relief spaceSealing stripAirtight seal (infill concreteor mortar joint)Precast panelINTERNALFigure 2.6: Setting back of sealant from the externalface of the panel (plan view)For better protection of the sealant from rain, windand UV light, the sealant may be set back from theexternal face of the wall as shown in Figure 2.6. Thishelps to minimise deterioration of the sealant.EXTERNALSealant set back fromexternal face4
According to CP 81:1999, the grooves that create thepressure relief space should comply with the followingminimum requirements:a)b)c)Figure 2.7: Dimensions of pressure relief space(plan view)EXTERNALWidth 15mmDepth 5mm; andSharp edges.The grooves that create the pressure relief space shouldbe located as shown in Figure 2.8 below, with thegrooves sloped at an angle not more than 10 fromthe vertical axis. 15mmGroove 5mmdesign of external wallsFigure 2.8: Typical details of a pressure relief spaceFlashingGroove10 maxINTERNALEXTERNALIf a sealing strip is to be used with the infillconcrete/mortar joint at the inner wall face as shownin Figure 2.5, its width should be equal to the jointgap plus sufficient overlap (approximately 60mm) oneach side of the joint. The sealing strip should be madeof an elastic material, or alternatively, some slack inthe sealing strip should be provided so that it doesnot tear under repeated stresses at the joint area. Asuitable gasket can also be used in place of the sealingstrip to create an airtight seal at the inner wall face.5Having an abutting cast in-situ concrete column orstiffener behind the joint can further enhancewatertightness of the joint. This type of joint is knownas the ‘wet’ or cast in-situ joint connection, and iseffective in preventing water seepage through theprecast joints. Examples of wet joints are shown inFigure 2.9 to 2.11.
Figure 2.9: Typical vertical joint with cast in-situ stiffener (plan view)EXTERNALBacker rodsSealantPrecast panelsNon-shrink cement groutPrecast panelsBars from precast panels(indicative)Cast in-situ stiffener(or column)Figure 2.10: Typical details for wet joint between precast panels (plan view)EXTERNALU bar fromprecast paneldesign of external wallsIn-situ lapping barPrecast façade panelSealant andbacker rodStarter barCast in-situ connectionFigure 2.11: Typical details for corner joint between precast panels (plan view)EXTERNALDowel barSealant and backer rodCast in-situ connectionCorrugated pipeLoop barLoop barLapping bar placed on sitePrecast façade panel*Note:Rebar details shown in Figure 2.9 to 2.11 are only indicative.Actual rebar detailing must be provided in structural design and drawings.6
2.3.3 INTERSECTIONS OF HORIZONTALAND VERTICAL JOINTSIntersections of the horizontal and vertical jointsshould be detailed to contain any incident water withinthe individual floor levels. To achieve this, a flashingcould be installed over a width of at least 120mm oneither side of the vertical joint as shown in Figure 2.12.recommends that for joints of more than 12mm width,the sealant depth should be half the width but notless than 12mm, and not exceeding the width of joint(see Figure 2.13).Figure 2.13: Typical sealant joint detailing for jointsof more than 12mm widthDepthFigure 2.12: Intersection of horizontal andvertical jointsEXTERNAL1/2 WidthSubjected to:12mm Depth WidthINTERNALFlashingWidthdesign of external wallsBacker rodMin120mm2.3.5 OTHER CONSIDERATIONS2.3.4 JOINT WIDTH AND DEPTHJoints between precast wall panels should haveadequate width to accommodate anticipatedmovements of the panels, and to ensure the jointsealant performs within its design capabilities. Whenthe joint gaps are too narrow, adjacent elements maycome into contact and be subject to undesired loading,distortion and cracks. A good practice is to provide ajoint gap of 12mm – 20mm to ensure properapplication of sealants.Joint depth is also an important factor as failures oftenoccur because the sealant depth is either too thick(cohesion failure, unable to stretch sufficiently) or toothin (adhesion failure, insufficient bonding to sidesof substrates) to function as intended.The depth of sealant depends on the type andconditions of service. Elasto-plastic sealants are usuallyapplied such that the depth is half the width formaximum movement accommodation and elasticsealants perform best in thin sections. CP 81:19997Window openings should be located within a singleprecast panel. Window openings formed across adjacentpanels may lead to water seepage into the windowhead.The use of integrated precast components, such asfaçade with beam, air con ledge, bay window, planterbox, etc, can offer better watertightness performanceas there are fewer construction joints.Ease of maintenance and repair should also beconsidered at the design stage. Sealants may needregular inspection, repair and replacement. Properaccess should be taken into consideration. For instance,the positioning of services or other features in frontof the joints will make future access difficult.
Figure 2.14: Location of window openings Window openingsPrecast panelsWindow frame located within a single panelWindow frame across adjacent panelsFaçade and beamFaçade and air con ledge2.4 EXTERNAL MASONRY BRICKWALLSIn general, external brickwalls have inferiorwatertightness performance than precast concrete wallsand cast in-situ RC walls. The quality of the erectedbrickwalls is highly workmanship-dependent.Due to its inferior watertightness performance,brickworks are not encouraged for use in theconstruction of external walls. Where the Designerdecides to use external brickwalls for the project, thefollowing good practices on designs of externaldesign of external wallsFigure 2.15: Examples of integrated precast componentsFaçade and bay windowbrickwalls should be adopted to achieve the requiredwatertightness performance.2.4.1 WALL THICKNESSHalf-brick thick walls have inferior waterproofingperformance compared to full-brick thick walls. Hence,where brickworks are used for external wallconstruction, full-brick thick walls with English bondinstead of half-brick thick walls with Stretcher bondshould be adopted.8
Figure 2.16: Full-brick thick brickwall with English BondHeaderStretcherCloserdesign of external walls2.4.2 COMPOSITION OF MORTARJOINTSCement mortar joints are relatively more porous andare, hence, more susceptible to water seepage than thebrick units. The type of mortar bedding selected canhave a considerable effect on its bonding strength andworkability, which in turn affects the watertightnessof the joints.Concrete kerbs of at least 100mm height should beprovided for external brickwalls to enhance theirwatertightness. As a good practice, these kerbs shouldbe provided at every storey. This is especially importantwhere there is a RC recess or a RC ledge at the beam/floor level.Figure 2.18: Concrete kerb at the base of brickwall2.4.3 PROVISION OF SURFACE FINISHESRendered brickwalls give better rain resistance thanfair-faced brickwalls. It is, however, essential to selectthe appropriate mix ratio, thickness and number ofcoats to minimise cracks in the rendering.Figure 2.17: Applying rendering to an external brickwall92.4.4 PROVISION OF CONCRETE KERBS
2.4.5 DAMP-PROOF COURSE (DPC)Ground water can penetrate the building fabric, risingvertically through capillary action. Damp-proof course(DPC) should be provided in masonry walls to guardagainst such ground moisture. To protect againstrainwater bouncing off the ground and splashing ontothe wall, the DPC should be installed at a minimum150mm height above the surrounding finishedfloor level.Figure 2.19: Installation of 4.6 JOINTS BETWEEN DISSIMILARMATERIALSWhere the brickwall abuts a concrete member, bondingbars should be provided at the joints to minimisecracks at these locations. These bonding bars shouldbe secured to the concrete member. Alternatively, thesebars could be cast together with the concrete member.Some bonding bar systems come with a lipped framethat is fastened to the concrete member. The lippedframe allows greater flexibility in positioning thebonding bars to facilitate brick-laying. The bondingbars should be of minimum 200mm length andinstalled at every 4th course of the brickwalls.design of external wallsFinished floor levelMin 150mmDPCA layer of mesh reinforcement should be provided atthe interfaces between dissimilar materials, for examplebetween brick and concrete members. The meshreinforcement helps to distribute stress and preventplaster crack at these locations.10
Figure 2.20: Joints between brick and RC membersLipped frameBonding barsfor full-brickthick wallsBonding barBonding bars with lipped frame systemdesign of external wallsRC columnINTERNALBrickMesh reinforcementExternal plasterEXTERNALMesh reinforcement at interfacebetween brickwall and RC column (plan view)2.4.7 MESH REINFORCEMENT INMORTAR JOINTSTo provide additional resistance to stresses, vibrationand thermal movement, mesh reinforcement shouldbe embedded in the mortar joints between courses ofbrickwork. The mesh reinforcement should be laidover the 1st or 2nd course and at every subsequent4th course of brickwork. There should be minimum150mm lapping where different sections of meshreinforcement overlap.11Bonding bar system without a lipped frameMesh reinforcement at interfacebetween brickwall and RC columnFigure 2.21: Mesh reinforcement embedded at every4th course
2.4.8 STIFFENERS AND MOVEMENT JOINTSVertical and horizontal stiffeners should be provided for big panels of brickwork. Consult the structural Engineerfor details of the stiffeners. Where brickwalls abut the stiffeners, steel bonding ties should be provided at every4th course.Figure 2.22: Example of a vertical RC stiffener for wallsFigure 2.23: Typical stiffener detailsRC stiffenerRC columnRC kerbRebar starters atevery 4th courseRebar with linksdesign of external wallsVertical movement joints of about 12mm width should be provided in brickwork at maximum 6m intervals.Joints should be filled with a suitable material, such as polyethylene strip or urethane sealant.Figure 2.24: Vertical movement jointsJoint sealant2.5OTHER DESIGN CONSIDERATIONS2.5.1 EXTERNAL BUILDING FEATURESExternal features such as bay windows, air conditioningledges and planter boxes are increasingly being usedin building projects. For such features, the followingprovisions should be considered: overhangs protruding minimum 300mm out ofthe building envelope help to shield the externalwalls (especially brickwalls) from direct rainfall; overhangs also help to shield wall openings (suchas window openings or M&E openings) from directrainfall; adequate fall along protruding features to avoidaccumulation of stagnant water at the corner joints;and drips provided at the underside of external featuresto prevent water flow towards the external walls.12
Figure 2.25: External brickwall with overhangTypical storey floor levelExternal brickwallEXTERNAL300mm protrusionINTERNALTypical storey floor leveldesign of external wallsFigure 2.26: Provision of overhangOverhang helps toshield wall openingsM&E openingWindow openingFigure 2.27: Provision of drip at underside of external featuresDrip10mmDrip linesprovided bothabove and belowthe bay windowSlope downwards25mm13 15mm
2.5.2 M&E SERVICESChasing of external walls for embedding M&E servicesreduces the effective thickness of the walls and weakensthe physical barrier against water ingress. Designersshould avoid running M&E services along externalwalls, especially external brickwalls.For RC walls, recess for embedding M&E servicesshould be provided during the concrete casting stage.Hacking of walls should be avoided. The effectivethickness of RC walls should be maintained at aminimum of 80mm.Figure 2.28: Recess provided in RC wall during concrete castingRecess for embeddingM&E servicesMin80mmServices that penetrate the external walls should behoused within trunking boxes. All gaps between thetrunking boxes and the external walls must becompletely sealed to ensure watertightness at thesePlan viewpenetrations. The penetration points should, wherepossible, be situated below an overhang element,as shown in Figure 2.26.Figure 2.29: M&E services that penetrate the external wallsHousing M&E services in trunking box (View from inside)design of external wallsRecess for M&E serviceRC WallHousing M&E services in trunking box (View from outside)14
2.5.3 WATERPROOFING APPLICATIONALONG PERIMETER WALLS ANDPLANTERSplanters (eg. environment decks), the requiredupturn of 300mm should be measured from thefinished soil level.A layer of waterproofing membrane should beapplied to the perimeter walls with an upturn ofminimum 300mm along the external walls, as shownin Figure 2.30. For external walls with surroundingFor external walls designed with surroundingconcrete planter box, it is a good practice to applywaterproofing membrane over the entire interior ofthe planter box, as shown in Figure 2.31.Figure 2.30: Waterproofing application along perimeter walls and plantersEXTERNALINTERNALExternal wall300mm upturn(from apron slab orfinished soil level)design of external wallsWaterproofingmembrane25 x 25 filletFigure 2.31: Planter boxEXTERNAL WALLWaterproofing membraneshould be applied to theentire interior of the planterbox (area A), with an upturnalong the top ledge (area B).BAPlanter box15
There are various external wall systems used in the local industry, including precast concrete walls, cast in-situ reinforced concrete walls, brickwalls, curtain walls, cladding walls, concrete block walls, etc. Due to volume constraint, this publication focuses on precast concrete walls, cast in-situ reinforced concrete walls and plastered .
Ceco Building Carlisle Gulf States Mesco Building Metal Sales Inc. Morin Corporation M.B.C.I. Nucor Building Star Building U.S.A. Building Varco Pruden Wedgcore Inc. Building A&S Building System Inland Building Steelox Building Summit Building Stran Buildings Pascoe Building Steelite Buil
COVER_Nationa Building Code Feb2020.indd 1 2020-02-27 2:27 PM. Prince Edward Island Building Codes Act and Regulations 1 . Inspection - means an inspection by a building official of an ongoing building construction, building system, or the material used in the building's construction, or an existing or completed building, in order .
BUILDING CODE Structure B1 BUILDING CODE B1 BUILDING CODE Durability B2 BUILDING CODE Access routes D1 BUILDING CODE External moisture E2 BUILDING CODE Hazardous building F2 materials BUILDING CODE Safety from F4 falling Contents 1.0 Scope and Definitions 3 2.0 Guidance and the Building Code 6 3.0 Design Criteria 8 4.0 Materials 32 – Glass 32 .
The Master of Building Construction (MBC) program is designed to provide advanced construction education for those who hold an undergraduate construction management or construction engineering degree or for those who are making a career change and hold an accredited undergraduate degree in another discipline.
Port Charlotte State Florida ZIP Code 33981 Company NAICNumber SECTION C - BUILDING ELEVATION INFORMATION (SURVEY REQUIRED) C1. Building elevations are based on: Construction Drawings* Building Under Construction* Finished Construction *A new Elevation Certificate will be required when construction of the building is complete. C2.
The construction industry experiences a larger burden of deaths at road construction sites than any other major industry. From 2011 to 2016, 532 construction workers were killed at road construction sites, more than twice as many fatalities as all other industries combined (chart 3). The number of fatalities among construction workers at
A tall building, a high-rise, or a tower is a 50 m (164 ft ) building. A skyscraper is a 150 m (328 ft ) building. A supertall or ultra-tall is a 300 m (984 ft ) building. A megatall is a 600 m (1967 ft ) building. 1.2. The Tall Building Construction Boom Since 1990, most cities have seen a steady increase in urban dwellers. In 1990, 43 .
Building automation is the centralized control of a building's heating, ventilation and air conditioning, lighting, and other systems through a Building Management System or Building Automation System (BAS). A building controlled by a BAS is often referred to as an intelligent building, or a "smart building".
