Installing And Configuring Cisco Secure Access Control System With .
Installing and Configuring the SecureAccess Control System with the CiscoSNS-3415 and Cisco SNS-3495This chapter describes how to install and initially configure the Cisco SNS-3415 or Cisco SNS-3495 and the ACS 5.8.1server.This chapter contains: Installing ACS on the Cisco SNS-3415 or 3495 Appliance, page 1 Downloading the Cisco Secure ACS 5.8.1 ISO Image, page 2 Installing the ACS Server, page 2 Resetting the Administrator Password, page 9 Reimaging the Cisco SNS-3415/3495 Appliance, page 10Installing ACS on the Cisco SNS-3415 or 3495 ApplianceThe Cisco SNS-3415 or Cisco SNS-3495 appliance is preinstalled with the ACS 5.8.1 software. This section gives youan overview of the installation process and the tasks that you must perform before installing ACS.Before you begin installing ACS 5.8.1, you must:1. Open the box and check the contents. See Unpacking and Inspecting the Server, page 22. Read Introducing the Cisco SNS-3415 and Cisco SNS-3495 Hardware Appliances, page 1.3. Read the general precautions and safety warnings in Preparing to Install the Cisco SNS 3415 and Cisco SNS 3495Hardware Appliances, page 14. Install the appliance in the rack. See Preparing for Server Installation, page 35. Connect the Cisco SNS-3415 or Cisco SNS-3495 to the network and appliance console. See Connecting Cables,page 66. Power up the Cisco SNS-3415 or Cisco SNS-3495 appliance. See Connecting and Powering On the CiscoSNS-3415/3495 Appliance, page 97. Power up the Cisco SNS-3415 or Cisco SNS-3495 appliance to the network and appliance console. See ConnectingCables, page 68. Run the setup command at the CLI prompt to configure the initial settings for the ACS server. See Running the SetupProgram, page 5. The setup can be done by using the appliance console or CIMC.You can use the Cisco UCS Server Configuration Utility, Release 3.0 User Guide to configure theCisco SNS-3415 or Cisco SNS-3495 appliance. You can also see the Cisco UCS C-Series Rack Server guides for moreinformation on Cisco SNS-3415 or Cisco SNS-3495 appliance.Cisco Systems, Inc.1www.cisco.com
Installing and Configuring the Secure Access Control System with the Cisco SNS-3415 and Cisco SNS-3495Downloading the Cisco Secure ACS 5.8.1 ISO ImageDownloading the Cisco Secure ACS 5.8.1 ISO ImageYou can download the Cisco Secure ACS 5.8.1 ISO image from Cisco.com1. Go to http://www.cisco.com/go/acs. You must already have a valid Cisco.com login credentials to access this link.2. Click Download Software.The Cisco Secure ACS Release 5.8.1 software image appears on the Cisco.com page. You can test all the Cisco ACSservices once your installation and initial configuration are complete.Note: You can download the ACS 5.x software images from Cisco.com only when you have a valid Software ApplicationSupport (SAS) contract for a previous version of ACS 5.x software. If you do not have a valid SAS contract for a previousversion, you must contact your Sales Engineer (SE), Accounts Manager (AM), or Cisco partners to publish the softwareimage on Cisco.com to the specific customers account.Installing the ACS ServerAfter you download the Cisco Secure ACS 5.8.1 ISO image, you can use any of the following options to install and setup the Cisco Secure ACS 5.8.1 software on your appliance: Configure the Cisco Integrated Management Interface (CIMC) and use it to install Cisco Secure ACS 5.8.1 remotelyvia the network. See Configuring CIMC, page 4, Installing ACS 5.8.1 on the Cisco SNS-3415/3495 ApplianceRemotely Using CIMC, page 2 and Running the Setup Program, page 5. Create a bootable USB Drive and use it to install Cisco Secure ACS 5.8.1. See Creating a Bootable USB Drive,page 4, Installing ACS 5.8.1 on the Cisco SNS-3415/3495 Appliance Using the USB Drive, page 3, and Running theSetup Program, page 5.Installing ACS 5.8.1 on the Cisco SNS-3415/3495 Appliance Remotely Using CIMCAfter you have configured the CIMC for your appliance, you can use it to manage your Cisco SNS-3415 or CiscoSNS-3495 appliance. You can perform all operations including BIOS configuration on your Cisco SNS-3415 or CiscoSNS-3495 appliance through the CIMC.1. Connect to the CIMC for server management. Connect Ethernet cables from your LAN to the server, using the portsthat you selected in NIC Mode setting. The Active-active and Active-passive NIC redundancy settings require youto connect to two ports.2. Use a browser and the IP address of the CIMC to log in to the CIMC Setup Utility. The IP address is based upon yourCIMC config settings that you made (either a static address or the address assigned by your DHCP server).Note: The default user name for the server is admin. The default password is password.3. Use your CIMC credentials to log in.4. Click Launch KVM Console.5. Click Virtual Media.6. Select Activate Virtual Devices from the list.You can view the check mark near to Activate Virtual Devices option.7. Click Virtual Media again, and select MAP CD/DVD option.8. Click Browse and locate the ACS 5.8.1 ISO image.9. Click Map Device.2
Installing and Configuring the Secure Access Control System with the Cisco SNS-3415 and Cisco SNS-3495Installing the ACS Server10. Choose Macros Static Macros Ctrl-Alt-Del to boot the Cisco SNS-3415 or Cisco SNS-3495 appliance usingthe ISO image.11. Enter F6 to bring up the boot menu. A screen similar to the following one appears.12. Select the Cisco vKVM-Mapped vDVD that you mapped and press Enter. The following message is displayed.Welcome to the Cisco Secure ACS 5.8.1 RecoveryTo boot from hard disk press Enter Available boot options:[1] Cisco Secure ACS Installation (Keyboard/Monitor)[2] Cisco Secure ACS Installation (Serial Console)[3] Recover administrator password (Keyboard/Monitor[4] Recover administrator password (Serial Console) Enter Boot existing OS from hard disk.Enter boot option and press Enter boot:13. At the boot prompt, enter 1 and press Enter.14. After you enter the network configuration parameters in the Setup mode, the appliance automatically reboots, andreturns to the shell prompt mode.15. Exit from the shell prompt mode. The appliance comes up.16. Continue with Verifying the Installation Process, page 5.Installing ACS 5.8.1 on the Cisco SNS-3415/3495 Appliance Using the USB DriveTo install ACS 5.8.1 on the Cisco SNS-3415 or Cisco SNS-3495 appliance using the USB drive, complete the followingsteps:Before You BeginYou need to create a bootable USB drive. See Creating a Bootable USB Drive, page 4.1. Power on the Cisco SNS-3415 or Cisco SNS-3495 appliance.3
Installing and Configuring the Secure Access Control System with the Cisco SNS-3415 and Cisco SNS-3495Installing the ACS Server2. Plug in your bootable USB drive that has the Cisco Secure ACS ISO image into the USB port.3. Restart ACS and go to the BIOS mode.4. In the BIOS mode, choose boot from USB.5. Exit from the BIOS mode and click Save.6. Again, restart ACS and boot from USB.7. Now, continue reimaging the Cisco SNS-3415 or Cisco SNS-3495 using the USB drive.The following message is displayed.Welcome to the Cisco Secure ACS 5.8.1 RecoveryTo boot from hard disk press Enter Available boot options:[1] Cisco Secure ACS Installation (Keyboard/Monitor)[2] Cisco Secure ACS Installation (Serial Console)[3] Reset administrator password (Keyboard/Monitor[4] Reset administrator password (Serial Console) Remove USB key and reboot to boot existing Hard Disk Please enter boot option and press Enter boot:8. At the boot prompt, enter 1 and press Enter.9. After you enter the network configuration parameters in Setup mode, the appliance automatically reboots andreturns to the shell prompt mode.10. Exit from the shell prompt mode. The appliance comes up.11. Continue with Verifying the Installation Process, page 5.Creating a Bootable USB DriveYou can download the ACS 5.8.1 USB Installation tool for SNS-3415, and SNS-3495(ACS 58 USB Installation tool.zip) zip from the Cisco Secure ACS 5.8.1 Download Software section on Cisco.com.This zip file contains the bootable scripts which
Installing the ACS Server After you download the Cisco Secure ACS 5.8.1 ISO image, you can use any of the following options to install and set up the Cisco Secure ACS 5.8.1 software on your appliance: Configure the Cisco Integrated Management Interface (CIMC) and use it to install Cisco Secure ACS 5.8.1 remotely via the network.
Cisco ASA 5505 Cisco ASA 5505SP Cisco ASA 5510 Cisco ASA 5510SP Cisco ASA 5520 Cisco ASA 5520 VPN Cisco ASA 5540 Cisco ASA 5540 VPN Premium Cisco ASA 5540 VPN Cisco ASA 5550 Cisco ASA 5580-20 Cisco ASA 5580-40 Cisco ASA 5585-X Cisco ASA w/ AIP-SSM Cisco ASA w/ CSC-SSM Cisco C7600 Ser
Apr 05, 2017 · Cisco 4G LTE and Cisco 4G LTE-Advanced Network Interface Module Installation Guide Table 1 Cisco 4G LTE NIM and Cisco 4G LTE-Advanced NIM SKUs Cisco 4G LTE NIM and Cisco 4G LTE-Advanced NIM SKUs Description Mode Operating Region Band NIM-4G-LTE-LA Cisco 4G LTE NIM module (LTE 2.5) for LATAM/APAC carriers. This SKU is File Size: 2MBPage Count: 18Explore furtherCisco 4G LTE Software Configuration Guide - GfK Etilizecontent.etilize.comSolved: 4G LTE Configuration - Cisco Communitycommunity.cisco.comCisco 4G LTE Software Configuration Guide - Ciscowww.cisco.comCisco 4G LTE-Advanced Configurationwww.cisco.com4G LTE Configuration - Cisco Communitycommunity.cisco.comRecommended to you b
Sep 11, 2017 · Note: Refer to the Getting Started with Cisco Commerce User Guide for detailed information on how to use common utilities for a record in Cisco Commerce. See Cisco Commerce Estimates and Configurations User Guide for more information.File Size: 664KBPage Count: 5Explore furtherSolved: Cisco Serial Number Lookups - Cisco Communitycommunity.cisco.comHow to view and/or update your CCO profilewww.cisco.comSolved: How do I associate a contract to my Cisco.com .community.cisco.comHow do I find my Cisco Contract Number? - Ciscowww.cisco.comPower calculator tool - Cisco Communitycommunity.cisco.comRecommended to you b
Cisco Nexus 1000V Cisco Nexus 1010 Cisco Nexus 4000 Cisco MDS 9100 Series Cisco Nexus 5000 Cisco Nexus 2000 Cisco Nexus 6000 Cisco MDS 9250i Multiservice Switch Cisco MDS 9700 Series Cisco Nexus 7000/7700 Cisco Nexus 3500 and 3000 CISCO NX-OS: From Hypervisor to Core CISCO DCNM: Single
Cisco 2951 2 2 Cisco 3925 4 4 Cisco 3945 4 4 Cisco 3925E 3 3 Cisco 3945E 3 3 Cisco 1841 1 1 Cisco 2801 2 1 Cisco 2811 2 1 Cisco 2821 2 1 Cisco 2851 2 1 Cisco 3825 4 2 Cisco 3845 4 4 Table 1A provides relevant software information Router Chassis Software Release Minimum Software Package Cisco 1921 15.0(1)M2 IP Base
Supported Devices - Cisco SiSi NetFlow supported Cisco devices Cisco Catalyst 3560 Cisco 800 Cisco 7200 Cisco Catalyst 3750 Cisco 1800 Cisco 7600 Cisco Catalyst 4500 Cisco 1900 Cisco 12000 Cisco Catalyst 6500 Cisco 2800 Cisco ASR se
Cisco Nexus 7706 Cisco ASR1001 . Cisco ISR 4431 Cisco Firepower 1010 Cisco Firepower 1140 Cisco Firepower 2110 Cisco Firepower 2130 Cisco FMC 1600 Cisco MDS 91485 Cisco Catalyst 3750X Cisco Catalyst 3850 Cisco Catalyst 4507 Cisco 5500 Wireless Controllers Cisco Aironet Access Points .
Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unified Computing System (Cisco UCS), Cisco UCS B-Series Blade Servers, Cisco UCS C-Series Rack Servers, Cisco UCS S-Series Storage Servers, Cisco UCS Manager, Cisco UCS
