INSTALLATION INSTRUCTIONS For Pre-Hung Exterior Entry Doors - Lowe's
INSTALLATION INSTRUCTIONSfor Pre-Hung Exterior Entry DoorsThank you for selecting Lowe’s ReliaBilt products. Attached areLowe’s ReliaBilt recommended installation instructions for ExteriorWood, Steel and Fiberglass Pre-Hung Doors. Read these instructionsthoroughly before beginning. They are designed to work in mostexisting applications; however, existing conditions may requirechanges to these instructions. If changes are needed, they are madeat the installer’s risk. For installations other than indicated in theseinstructions, contact a building professional. Areas such as Floridaand the Texas TDI region have different anchoring requirementsbased on product certification. For information on specific products,visit www.floridabuilding.org or www.tdi.texas.gov and follow theanchoring schedule given in the drawings for the product instead ofthe anchoring schedule in this document.Newer construction methods have led to an increase in air and watertightness in buildings. This frequently leads to negative air pressureinside the house, which can draw water through very small openings.Our installation method seals the door to the weather barrier (typicallybuilding wrap) and uses a sill pan to capture and drain incidental stormwater from under the door.IMPORTANT INFORMATION AND GLOSSARYNot all exterior door types may be installed into every wall conditionin all areas. Consult your local building code official (or Authorityhaving Jurisdiction) for applicable building codes and regulations.Local building code requirements supersede recommended installationinstructions.Please Note! Any exterior door installation where the sill is higher than35 feet above ground level or into a wall condition not specificallyaddressed in these instructions must be designed by an architect orstructural engineer. Failure to install square, level and plumb and on aflat surface (without twist or warp) could result in denial of warrantyclaims for operational or performance problems.Note to Installer: Provide a copy of these instructions to the buildingowner. By installing this product, you acknowledge the terms andconditions of the limited warranty as part of the terms of the sale.Sill PanA flashing component installed in the sill of the rough openingunderneath the door. Sill pans have upturned walls along the interioredge and at both ends, creating a three-sided box. This componentserves as a collection device to drain incidental water to the exterior ofthe building and should be properly sealed to the opening. The best sillpan design has a positive slope to the exterior and offers continuoussupport to the door’s sill.Strike JambThe side of the jamb that makes contact with the latch on a door slab.Please allow sufficient time to properly prepare the rough opening,install the entry door, and ensure its proper operation.GLOSSARYBacker Rod (backing material)A material (e.g. foam rod), placed into a joint primarily to control thedepth of the sealant.BuckA wood framework attached to the masonry inside a window or a doorrough opening.Door System/Pre-Hung DoorA pre-cut and assembled unit consisting of a door slab (prepared for thelocking or passage hardware) hung on hinges in a wood or metal frame.Hinge JambThe side of the jamb on which the hinges of a door are installed.Rough OpeningThe framed opening in a wall where a door is to be installed.Security PlateA metal plate pre-installed into the frame of a pre-hung door. It isdesigned to provide extra strength and stability from a forced entryattempt by allowing the latch of the door to rest inside it when thedoor is closed.ShiplapThe layering method in which each layer overlaps the layer below it sothat water runs down the outside.Shipping StrapSmall, metal or plastic clips that come attached to a door system.These clips help keep a door slab closed and aligned before andduring installation.SideliteA fixed, usually rectangular window placed on either side of a door.1LANDINGSThese instructions covertwo sill conditions: thestep-down landingand the continuousslab landing. Theinstallation methodsvary slightly betweenlanding types.Step-Down LandingContinuousSlabLanding
INSTALLATION INSTRUCTIONSfor Pre-Hung Exterior Entry Doors (JII106)ROUGH OPENINGSThis installation guide specifically addresses masonry/block wall,sheathed wall and open-stud construction.MASONRY/BLOCK WALL CONSTRUCTIONThis installationassumes that a buildingprofessional has alreadyproperly fastened andsealed a framework ofstuds (often called abuck) to the concrete/masonry wall.Masonry/Block Wall ConstructionFULLY SHEATHED WALL CONSTRUCTIONThe wall framing is coveredby sheathing and the doorwill be mounted withthe exterior trim flushagainst the sheathing. Thisinstallation assumes buildingwrap is properly installedprior to installation.Fully Sheathed Wall l areaBuckOPEN-STUD CONSTRUCTIONThe wall framing needs to be completely surrounded by backingsupport (non-water degradable, thin (max. 1/8" thick) sheet materialsuch as plywood or lauan) before installing building wrap and thedoor. The door will be mounted with the exterior trim flush against theapplied backing support.SAFETY AND HANDLINGSAFETY Read and fully understand ALL manufacturer’s instructions beforebeginning. Failure to follow proper installation instructions may result inthe denial of warranty claims for operational or performance problems. Do not work alone. Two or more people are required. Use safelifting techniques. Use caution when handling glass. Broken or cracked glass can causeserious injury. Wear protective gear (e.g. safety glasses, gloves, ear protection, etc.). Operate hand/power tools safely and follow manufacturer’soperating instructions. Use caution when working at elevated heights. If disturbing existing paint, take proper precautions if lead paint issuspected (commonly used before 1979). Your regional EPA(www.epa.gov/lead) or Consumer Product Safety Commission officesprovide information regarding regulations and lead protection. WARNING: Drilling, sawing, sanding or machining wood productsgenerates wood dust, a substance known to the State of California tocause cancer. Use a respirator or other safeguards to avoid inhalingwood dust.MATERIALS AND DOOR HANDLING Make sure the operating panel is secured prior to installation. Heed material manufacturer’s handling and application instructions. Protect adhesive surfaces from dirt, moisture, direct sunlight andfolding over onto themselves. Handle in vertical position; do not drag on floor. Do not put stress on joints, corners or frames. Store door in dry, well-ventilated area in vertical, leaning position toallow air circulation; do not stack horizontally. Protect from exposure to direct sunlight during storage. Install only into vertical walls and when conditions and sheathingare dry.IF INJURY OCCURS, IMMEDIATELY SEEK MEDICAL ATTENTION!MATERIALS AND TOOLSPROVIDED MATERIALS 2 - #9 x 2-1/2" screws. Foam weatherstrip wedges (corner seal pads).NEEDED MATERIALSNote! Lowe’s Reliabilt exterior window and door products shouldbe installed in accordance with Lowe’s Reliabilt recommendedinstallation and flashing directions, which are shipped with theproducts. Note that alternative installation methods and flashingsystems may be utilized at the installer’s or owner’s discretion and, insuch situations the installation should be done in accordance with theflashing manufacturer’s instructions. Follow all material manufacturer’sinstructions for proper use and compatibility. When using flashing,spray adhesive/primer, sealant and foam products, we recommendusing the same manufacturer and verifying compatibility. It is the EndUser’s responsibility to determine if dissimilar materials are compatibleto the substrates in the application.2 Lockset 10d galvanized casing nails (if plan to stain) or #8 x 2-1/2" deck screws(if plan to paint). Non-compressible or non-water degradable shims. Sill pan: It is best practice to use a pre-formed, rigid, positively sloped,pvc pan that provides continuous support. An alternative would be anon-sloped pre-formed sill pan or one that can be fabricated on-sitefrom metal or vinyl sheet material with the proper tools. Backer rod 1/8" larger than the widest portion of the gap (used inconjunction with sealant bead). Sealant: We recommend OSI QUAD Max Sealant or equivalent. Thiscan be used in any application and can be painted or ordered in acolor matched product, if desired. Polyurethane low expansion Window and Door foam: We recommendOSI QUAD Foam or equivalent). Plastic drain screen with crisscross or woven pattern (sold in 6" widthsto protect rain gutters) for step-down landings.
INSTALLATION INSTRUCTIONSfor Pre-Hung Exterior Entry Doors (JII106)MATERIALS AND TOOLS - CONTINUED 3/8" staples for step-down landings. Drip cap, if required because of door location and exposure. Doorswith an adequate overhang may not need a drip cap.For installations into a Buck: Liquid applied flashing (Protecto Wrap LWM 200 or equivalent).For installations into a stud-framed wall: 4", 6", or 9" (as required by local code and window configuration)wide self-adhered flashing: We recommend OSI QUAD Butyl FlashingTape or equivalent.1 J-rollerCaulking gunDrill with bitsConstruction staplerHammerScrewdrivers Nail setSquarePencilPry barSmall punch ormagnetREMOVE PACKAGING AND INSPECT DOORREMOVE PACKAGINGRemove shipping materials such as corner covers, shipping blocksor pads. Remove any staples exposed on the frame, but leave glassprotective films.1. If the door unitincludes packagingor a skidboard underthe threshold andbottom end of theside jamb, removeit. If the door comeswith a security plateon the outside of theframe at the strike,DO NOT removeit. Install the doorwith the securityplate attached.Note! If the door hasshipping straps, DONOT remove themuntil instructed todo so. These holdthe door systemaligned and closedduring installation.Shipping strapSkidboardINSPECT DOORSecurity plate2. If the door isfastened closedwith a duplexnail or removableplastic plug, removethese along withthe packagingand crating.Shipping strap3NEEDED TOOLS Cutting shears (sillpan) Tape measure Utility knife Level (4 ft. minimumrecommended) Cosmetic damage. Product squareness (diagonal measurements must be within1/4" difference). Correct product (size, color, grid pattern, handing (side the hinges areon), glazing, energy-efficiency requirements, etc.).If any of the above conditions represent a concern, or if you expectenvironmental conditions to exceed the door’s performancerating, do not install the door. Contact your dealer or distributorfor recommendations.
INSTALLATION INSTRUCTIONSfor Pre-Hung Exterior Entry Doors (JII106)2INSPECT ROUGH OPENING Determine prior toVerify Square, Level and Plumbinstallation what theactual finish floorheight will be andadjust the roughopening if neededAto accommodate ataller unit height.Most doors use aEC1-3/8" high thresholdwhich providesadequate clearanceDin most applications.BThis ensures that thedoor does not dragon interior floorsafter installation. Verify the door is 1" narrower and 3/4" shorter (1/2" each smaller ifcode requires) than the rough opening width/height. 90-minute firedoors should be 1-1/4" narrower and 5/8" shorter.3 Verify the rough opening is square. The (A) and (B) measurementsshould be the same. Maximum allowable deviation from squareis 1/4". Verify the rough opening is plumb (C, E and D). The maximumallowable deviation is 1/8". The rough opening sill must not be crowned or sagged (D), but ratherbe level or sloped (positive slope) to the exterior. The exterior face of the rough opening must be in a single plane (E)with less than 1/8" twist from corner to corner. Minimum double studs should be used at all wood framedrough openings. The header must be supported by trimmer studs.FOR RETROFIT INSTALLATIONSAfter removing the old door, remove sufficient cladding (siding, stucco,etc.) to expose enough intact building wrap to properly seal the doorsystem to the opening. If damaged, apply new building wrap in shiplapmanner. Verify the rough opening framing is structurally sound. Contactyour local waste management entities for proper disposal or recyclingof products being removed.INSTALL SILL PANThe sill can be prepared using one of two methods: It is best practiceto use a pre-formed, rigid, positively sloped, pvc pan that providescontinuous support. As an alternative, a sill pan can be fabricated onsite, by following the instructions below.JOBSITE FABRICATED SILL PAN1. Cut a piece of sheetmaterial to thelength shown.2. Lightly crease foldinglines 1/2" in from thetwo short sides andone long side.3. Measure the distancefrom the back of thetrim to the interioredge of the sill andadd 9/16".4. Take this distancefrom the back edgeand lightly crease afolding line acrossthe sheet material.5. For step-downlandings, cut 1/2"in at this line onboth sides of thesheet material.Length of rough opening sill plus 1"½"6. For continuousslab, cut across thefolding line.7. Fold the three backsides up to make a3-sided box, and, forstep-down landings,fold the frontflap down.Continuous slabStep-down½"Sill width 9/16"INSTALL SILL PANFolding line½"½"InteriorMeasureframewidthFold sides and back upFold cornerforward1. Set the sill pan inthe rough opening,aligning the frontedge (for continuousslab) or folded downedge (for step-down)with the exterior ofthe rough opening.2. Mark a line acrossthe front and back ofthe sill pan.3. Apply three 3/8"beads of sealantbetween the lines.4. Place the sill pan inthe rough opening.Firmly press the sillpan into the sealantwith a J-roller.Fold frontflap downSealant4
INSTALLATION INSTRUCTIONSfor Pre-Hung Exterior Entry Doors (JII106)4PREPARE BUCKNote! This section applies to installations into a buck only. Forinstallations into a stud-framed wall, begin with section 5, “PREPARESTUD-FRAMED WALL.”1. Seal any joint larger than 1/16" in the buck and between the buckand the concrete/masonry with sealant.2. Cover the buck and the surrounding concrete/masonry at the headand jambs and sill with liquid applied flashing as shown.END of Buck Instructions, SKIP to section 6, “INSTALL DOOR.”Liquid appliedflashingSealant joints5PREPARE STUD-FRAMED WALLFOR RETROFIT INSTALLATIONSAfter removing the old door, remove sufficient siding to expose at least9" of intact building wrap. If damaged, apply new building wrap in ashiplap manner. Verify header and trimmer studs are structurally sound.PREPARE BUILDING WRAPVerify these steps are allowed by the building wrap manufacturer.1. Trim buildingwrap flush withthe edges of therough opening.2. If installing a dripcap, (recommended6"because thisintegrates thebuilding wrap and45 drip cap to protectthe structure andthe product fromincidental water)at the head, slitbuilding wrap 6"at 45 . Tape upas shown.3. Trim the sidessufficiently to allowthe nailing fin to bemounted againstthe sheathing.4. Apply spray adhesive/primer to the sillpan and surrounding area. Follow manufacturer’s instructions forapplication methods.5. Cut a piece of self-adhered flashing the length of the sill and applyover the sill pan as shown. The bottom of the sill pan should becompletely covered by the self-adhered flashing. For step-downlandings, fold flashing down as shown. For continuous slabs, trimflush with rough opening.56. Cut two pieces ofself-adhered flashing6"6" wide by the sillpan width 3" long.Sill panwidtha. For continuousslab landingsDiscard(foronly, cut out the3" continuousslab only)inside corner.b. Adhere the piecesof flashing to theStep-Downinside corners.Landing3"Stretch flashingSill pan3"as needed towidthcover corners andlay flat.7. Smooth gaps orSill panwidthbubbles beneathself-adhered flashingwith a J-rollerContinuous Slab3"Landing(remove and replaceif necessary).3"8. Seal back corners ofsill pan with sealant.9. For step-downlandings only, cutplastic drain screenSealantto length of sill 1"2" and staple 1/2"below sill edge. The1/2"drain screen providesa path for air todry any incidentalmoisture in therough opening.End of Stud-Framed Wall Instructions, continue with section 6,“INSTALL DOOR.”
INSTALLATION INSTRUCTIONSfor Pre-Hung Exterior Entry Doors (JII106)6INSTALL DOORWarning! To avoid injury, use at least two people to install. Adequatelysupport the door until fully installed.PREPARE DOOR1. On the interior side,apply a continuousbead of siliconesealant where theexterior trim meetsthe door frame asshown. Tool into afillet shape.2. Apply a 3/8"continuous bead ofsealant across the sillpan back dam andover the flashingjoints as shown.SealantSealantINSTALL DOORWarning! If installing fasteners through fiberglass components, werecommend pre-drilling holes to keep the fiberglass from splitting.Note! This section covers single door, double door, and doors with atransom or a sidelite(s) already installed by the factory.1. Remove any pre-hanging clips that are fastened to the outside ofthe jamb that will be covered when the unit is placed in the roughopening. Adequately support the slab to keep it from swinging openduring installation.2. For units withbrickmould trim,apply a 3/8" beadof sealant to theback of the trimwhere it will contactthe structure. Fromthe outside, tilt theentire pre-hung doorinto the center ofthe opening. Makesure the sill contactsthe sealant on thesill pan back dam(upturned leg onthe interior).63. Temporarily fastenthe door as follows.For metal frames,drive a nail or screw20"16"through one lowerhole in the flange.For doors withoutFastenera sidelite(s), securethe hinge jamb byplacing one 10dcasing nail (or one#8 x 2-1/2" deckscrew) horizontallyShim Locationscentered in the hingejamb or brickmouldtrim 20" from thetop and bottom(or just above thelower hinge) of the20"16"door. Do not setnails/screws. Forappearance reasons,fasteners can bedriven behind (butnot through) the weatherstrip if desired. Secure sidelite(s) in a similarmanner through the frame and into the wall.4. From the inside, shim the jambs as follows: One shim on each endof the sill (between jamb and sill, not under sill). Single/double unitsat each hinge location and at the strike plate. Units with sidelites,between the sidelite and wall in at least 3 places until the door issquare in the opening.5. For doors with metal frames, secure with nails or screws through theprovided holes in the frame either above or below every oval slot. Forall other doors, temporarily fasten the latch jamb by placing one 10dcasing nail (or one #8 x 2-1/2" deck screw) horizontally centered inthe latch jamb 16" from the top and bottom of the door. Do not setnails/screws.6. Verify the door unit is square, then securely fasten the hinge jambby setting the two nails or screws installed earlier. Add an additionalnail or screw centered between the first two and one 4" fromeach corner.7. Remove any remaining pre-hanging clips. Be sure the door opensfreely and that the space between the door and the jamb is even onall sides. Adjust if necessary by loosening or removing the strike jambfasteners and adjust until there is even contact between the slab andweatherstrip. Secure all fasteners.DOUBLE DOOR, SIDELITE OR TRANSOM INSTALLATIONS1. If installing a door with a sidelite(s), shim the head on both sides ofthe joint where the sidelite joins the door jamb. Fasten next to theshims and then remove shims.2. Shim the head of double door units or units with sidelite(s) at thecenter of each slab/sidelite. Fasten next to the shims and then removeshims. Fasten a transom in a similar manner every 16".
INSTALLATION INSTRUCTIONSfor Pre-Hung Exterior Entry Doors (JII106)6INSTALL DOOR - CONTINUED3. From the inside ofdoors with sidelitesinstalled on a woodfloor, pre-drill for #8screws and fill theholes with sealant.Drive two #8 x 2-1/2"deck screws througheach door jamband sidelite intothe floor in thelocations shown.4. Some double doorunits may requireBox unit showninstalling lock bolts atthe top and bottomof the inactive panel.Follow the instructionsthat come with theproduct if available.Otherwise, locate thecenter point of eachlock bolt, drill 3/8"bolt holes and install keeper plates.InteriorDoorframeSideliteframeFINISH INSTALLATION1. Re-check for smooth door operation and even spacing between thedoor and jamb. Secure the strike jamb evenly between the first twoalready in place with two more 10d casing nails (or #8 x 2-1/2" deckscrews) behind the weatherstrip.Note! Steps 2 and 3 apply only to units with hinge jamb(s) against therough opening.2. Install two providedFastening for Top Hinge Only#9 x 2-1/2" woodscrews in the tophinge through theWeatherstriptwo holes closest tothe weatherstrip,driving them throughthe hinge jamb andInstall screwsinto the studs. Ifnecessary, removethe screws already inthe hinges to insertthese longer screws.3. If installing a doorwith a metal frame,on the exterior,slide the “L” shapedhead piece intothe inner sectionand center it in theopening. Install thejamb pieces makingsure they are tightagainst the headpiece and roughopening. Secure withfasteners throughthe provided holes.74. If installing a doorwith a metal frameWeatherstripand adjustableT-Strike, place A overDeadboltB and place in thecover platebore in the frame.Install screws but donot tighten. Closedoor and push Binward until the doorslightly compressesABthe weatherstrip.Open door andtighten screws.5. At the sill, pullthe weatherstripWedgeup slightly andapply a bead ofsealant (behind theweatherstrip) at theSealantintersection of thejambs, brickmoulds,thresholds andfloor as shown.The included foamwedges are usedto complete theweatherstrip seal ateach bottom corner between the jamb and operating slab(s) whenclosed. Position the thick edge behind the weatherstrip, remove thebacking paper and adhere to the jamb as shown.6. Install drip cap if required or desired. Fold the building wrap(previously taped up) down over the drip cap and seal the cut endswith self-adhered flashing or building wrap tape.7. For metal frames,apply casing to bothsides. Mark thelocations of the ovalslots in the frameonto the casing andsecure casing withfasteners through theoval slots. For snapon steel casing, referto the instructionswith the clips.8. Apply sealant aroundthe outside of thedoor unit betweenthe siding andbrickmould, betweenthe brickmouldand the jamband between thejamb sides and thethreshold. Apply adiscontinuous beadof sealant (1/2"gap every 1') alongthe front side ofthe threshold.
INSTALLATION INSTRUCTIONSfor Pre-Hung Exterior Entry Doors (JII106)6INSTALL DOOR - CONTINUEDFINISH INSTALLATION - CONTINUED9. Create a continuous air seal on the interior between the rough openingand the door frame with low expansion foam.10. Ensure sealant on back dam of the sill pan fully seals to the insideface of the sill. Apply more sealant as necessary.11. On the exterior of step-down landings, install support trimunderneath the sill where it extends past the landing. Position trimsnugly against the bottom of the sill toe/nose.7FIRE DOOR HINGESDo not remove or paint over any fire labels. Automatically closinghinges are required on fire doors and when allowed to close bythemselves from 18", should close and latch securely. If it does not,adjust the spring as follows:1. With the doorclosed, insert theprovided hex wrenchTensionso that it can bepinrotated clockwise.Hold in place andremove tension pinTensionwith a small punchholeor magnet.Clockwise2. Rotate hex wrenchclockwise 1/4 turnand re-insert tensionpin loosely intotension hole.3. Remove hex wrench and try closing force.4. Repeat steps until closing force is adequate but do not rotate past 3ooholes on 180 openings or 4 holes on 90 openings.COMPLETE INSTALLATION1. If installing a fire door, verify the correct seal (weatherstrip) isinstalled in the frame and conforms to local codes.2. Fill any nail/screw holes and sand smooth.3. Finish all six sides of the door slab as well as the frame.4. Install exterior wall surface within seven days of installation.5. Install lockset hardware per supplied instructions.6. Remove protective film (if applicable) on glass after all construction iscomplete or within one year.7. Protect recently installed units from damage from plaster, paint, etc.by covering the unit with plastic.8. Install any interior trim as desired.9. Sealant joints will need to be inspected at least once a year andrepaired as necessary.Ask about Lowe’s installation services.Learn more at lowes.com/installation. 2014 Lowe’s Companies, Inc. All rights reserved. Lowe’s, the gable design andNever Stop Improving are trademarks of LF, LLC. All are used with permission.8JII106-Lowes (04/15)
A pre-cut and assembled unit consisting of a door slab (prepared for the locking or passage hardware) hung on hinges in a wood or metal frame. Hinge Jamb The side of the jamb on which the hinges of a door are installed. Rough Opening The framed opening in a wall where a door is to be installed. Security Plate
Bruksanvisning för bilstereo . Bruksanvisning for bilstereo . Instrukcja obsługi samochodowego odtwarzacza stereo . Operating Instructions for Car Stereo . 610-104 . SV . Bruksanvisning i original
10 tips och tricks för att lyckas med ert sap-projekt 20 SAPSANYTT 2/2015 De flesta projektledare känner säkert till Cobb’s paradox. Martin Cobb verkade som CIO för sekretariatet för Treasury Board of Canada 1995 då han ställde frågan
service i Norge och Finland drivs inom ramen för ett enskilt företag (NRK. 1 och Yleisradio), fin ns det i Sverige tre: Ett för tv (Sveriges Television , SVT ), ett för radio (Sveriges Radio , SR ) och ett för utbildnings program (Sveriges Utbildningsradio, UR, vilket till följd av sin begränsade storlek inte återfinns bland de 25 största
Hotell För hotell anges de tre klasserna A/B, C och D. Det betyder att den "normala" standarden C är acceptabel men att motiven för en högre standard är starka. Ljudklass C motsvarar de tidigare normkraven för hotell, ljudklass A/B motsvarar kraven för moderna hotell med hög standard och ljudklass D kan användas vid
LÄS NOGGRANT FÖLJANDE VILLKOR FÖR APPLE DEVELOPER PROGRAM LICENCE . Apple Developer Program License Agreement Syfte Du vill använda Apple-mjukvara (enligt definitionen nedan) för att utveckla en eller flera Applikationer (enligt definitionen nedan) för Apple-märkta produkter. . Applikationer som utvecklas för iOS-produkter, Apple .
April 2017 Ultimate Double Hung G2 4/24/2017 Introduction of the Ultimate Double Hung G2. enhanced locking system. Features include a centralized locking point at the check rail, a complete metal drive locking system and an updated jamb receiver assembly to assist with installation. Present December 2017
Fleming Road 936 Lei Muk Shue – Causeway Bay Cotton Path 960 Kin Sang – Wan Chai North 960A Central Hung Shui Kiu Hung Fuk Estate 960B Quarry Bay Hung Shui Kiu Hung . Sarah Lee Joey Lam T 852 2114 2103 T 852 2864 4865 E sarah.lee@hkcg.com.hk E joey.lam@hkcg.com.hk Below attached photographs for your use. .
Phần II: Văn học phục hưng- Văn học Tây Âu thế kỷ 14- 15-16 Chương I: Khái quát Thời đại phục hưng và phong trào văn hoá phục hưng Trong hai thế kỉ XV và XVI, châu Âu dấy lên cuộc vận động tư tưởng và văn hoá mới rấ
