PRODUCT DATA SHEET Sikagard -7600 HG
PRODUCT DATA SHEETSikagard -7600 HGTWO-COMPONENT POLYURETHANE, ROLLER GRADE, BITUMEN MODIFIED WATERPROOFINGMEMBRANEPRODUCT DESCRIPTIONCHARACTERISTICS / ADVANTAGESSikagard 7600 is a two-component, liquid applied,asphalt extended polyurethane sealer used in awaterproofing membrane system. The system isavailable in 2 grades. Sikagard 7600 HG - roller gradecan be applied over horizontal and vertical surface . USES WaterproofingTank LinerPond LinerCooling Tower linerPotable Water ContainmentReservoirsHybrid Traffic system base coat over asphaltic surfacesEconomical and easy to apply systemSeamless system which bridges cracks and jointsImpervious to water and aqueous chemicalsMeets California VOC and AQMD Requirements,Including SCAQMD Areas ANSI / NSF 61 Approved for contact with PotableWater Abrasion Resistant UV StablePRODUCT INFORMATIONPackagingComponent A - 0.45 gal. pailComponent B - 4.05 gal. pail1 Unit 4 x 4.5 gal. pail A BAppearance / ColorComponent A TransparentComponent B BlackShelf Life12 months from date of manufacture in original, factory-sealed containers.Storage ConditionsStore indoors at a temperature between 60–95 F (15–35 C)Densitycomp. B: 8 lbs/galcomp. A: 10.1 lbs/galMixed & Cured: 8.3 lbs/galSolid content by weight95 2 %Product Data SheetSikagard -7600 HGJanuary 2020, Version 01.030203030200300000121/6(ASTM D-236)
Solid content by volume89 2 %Volatile organic compound (VOC) content78 g/L(ASTM D-2697)(ASTM D-2369-81)TECHNICAL INFORMATIONElongation at Break450 % 50 %Chemical ResistanceResistance to aqueous chemicals and waste water.Please see chemical resistance chart.Resistance to Weatheringdone for 5000 hBehavior after Artificial WeatheringWeathering (ASTM D822) done for 5000 hrsTensile Strength (ASTM D-412) . 1000 psi 50 psi 5.86Mpa 0.3 MpaTear Strenght (Die C, ASTM D-624) .180 50 pliHardness (ASTM D-2240) . 60 5 Shore AAdhesion to Concrete (dry) Elcometer . 350 psiAbrasion Resistance - Weight Loss (ASTM D4060) . 1.2 mg lossDeflection Temperature (ASTM D648) .passElastomeric Waterproofing (ASTM C836) .exceeds(ASTM C957) . exceedsExtension to Break (ASTM D2859) . 450 100Liner Performance Crack Bridging . 10 cycles @ - 15 F 1/8”; After heat aging 1/4”Liner Weight ( 60 mil wet film thickness) .30 lbs/100 sq.f.Mullen Burst Strenght (ASTM D751). 50 mil 155 psiRecovery from 100% Extention after 5 minutes . 98%after 24 hours .100%Softening Point, Ring & Ball (ASTM D36) . 400 FDeflection Temperature (ASTM D648) . -60 FPermeability to Water Vapor0.03 permsService Temperature-60–220 F(ASTM D-412)75 F (24 C)50 % R.H.(ASTM D-822)75 F (24 C)50 % R.H.(ASTM D-751)75 F (24 C)50 % R.H.APPLICATION INFORMATIONCoverage48 ft²/gal24 ft²/gal16 ft²/gal12 ft²/galPot Life30 minutes (standard ambient conditions 70 Fo , 50% humidity)results in 30 mils DFT (standard per 1 coat)results in 60 mils DFTresults in 90 mils DFTresults in 120 mils DFTSURFACE PREPARATIONany other contaminants. All projections, rough spots,etc. should be dressed off to achieve a level surface priorto application.Surface must be clean, dry and sound with an opentexture. Remove dust, laitance, grease, curingcompounds, bond inhibiting impregnations, waxes, andConcrete - New concrete must be cured a minimum of28 days prior to application. Old concrete must be freeof loose aggregate, dirt and be dry. New and oldAPPLICATION INSTRUCTIONSProduct Data SheetSikagard -7600 HGJanuary 2020, Version 01.030203030200300000122/6
concrete should be Shot-, Water- or Abrasive-blasted.Grease spots and oil should be chemically cleaned withappropriate cleaners or mechanically removed .Asphalt - New asphalt must be cured a minimum of 28days prior to application. Old asphalt must be free ofloose aggregate, dirt and be dry. New and old asphaltshould be Shot-, Water- or Abrasive-blasted. Lowerambient temperature will help to make cleaning processmore effective. Grease spots and oil should be cleanedwith appropriate cleaners or mechanically removed.Metal - Should be thoroughly cleaned by grinding orblast cleaning. Be aware of dew point and check itbefore every application on metal surface.Plywood - The only acceptable grade of plywood is APArated exterior grade or better. The appearance andphysical characteristics of the plywoodand grade shouldbe considered. Plywood should be new or cleaned andsanded.Priming: To promote adhesion and minimize outgassing,priming is recommended on all surfaces except for newplywood. New plywood priming is optional. Concrete, Old Plywood - Sikalastic PF Lo-VOC Primer, Sikalastic FTP Lo-VOC Primer , Metal - Sikalastic PF Lo-VOC Primer, Sikalastic EP Primer Asphalt - Sikalastic Recoat Primer, Sikalastic EP PrimerAPPLICATIONMixingIt is essential that proper mixing methods and tools areused to ensure proper application of Sikagard -7600 HG. Mixing Drill: Low Speed Mixing Drill ( 400-600 rpm) Mixing Paddle: Jiffy Mixer ( 5-50 Gallon Model) or MudMixing Paddle ( 9-5/8" WIDE x 6-1/4" DEEP) Premixing: Premix each pail of Sikagard -7600 HG PartB (4.05 gal.) using the recommended drill and mixingpaddle at slow speed for a minimum of 1.5 minutes toensure Sikagard -7600 HG Part B is a homogeneousmixture. Mixing A & B component: With mixing paddle in thePart-B, turn on mixing drill and begin mixing Sikagard 7600 HG Part B, and while the mixing paddle isspinning slowly add one 0.45 gallon can of Sikagard 7600 HG Part-A to the center of the vortex created bythe mixing paddle. Once Part-A has been added, mixcontinuously for an additional 3 minutes using a veryslow up and down motion, making sure full pail ismixed evenly, including the sides of the pail. NOTE: Take care not to allow entrapment of air intothe material. Do not mix in an aggressive up and downmotion. Do not estimate mixing time. Do not thin. Donot hand mix. Mix the whole pail. Do not batch down.If a greenish hue can be seen at the top of the pail thenproduct has not been mixed properly.Product Data SheetSikagard -7600 HGJanuary 2020, Version 01.030203030200300000123/6Top: Jiffy Style Paddle Bottom: Mud Mixing Paddle
Phase 1 (Primer): When required; prime the surface atthe rate of 1 gal / 200 - 300 sq.ft. . Apply using a brush orphenolic core roller. This will result in 5 - 7 dry mils ofcoating. Priming is optional. Don’t prime over an existingdetail coat.NOTE: For rough or porous concrete or when outgassingis a concern, use Sikalastic PF Lo-VOC Primer orSikalastic FTP LoVOC Primer at an approximate rate of180 - 230 sq.f/1 gal. This rate may vary on the porosityof the substrate. Allow primer to become tack freebefore proceeding to the next phase.Phase 2 ( Cracks, Joints, Detailing):Detail Coat: Apply 30 mils of detail coat Sikagard 7600over all joints,transitions, cracks and flashing.Cracks inconcrete/asphalt over 1/8” must be filled with Sikagard 7600. Using Sikagard 7600 as caulking compound willshorten the curing time over conventional polyurethanecaulks.Reinforced Detail Coat: Apply 15 mils of detail coatSikagard 7600 over all joints, cracks and flashing.Cracks in concrete/asphalt over 1/8” must be filled withSikagard 7600 . Bridge joints, cracks, and flashings with3” or 6” FlexiTape Heavy pushing it into the Sikagard 7600 HG over all joints, cracks and flashings. Overreinforcement , apply 10–15 mils stripe coat ofSikagard 7600 and taper it onto adjacent surface. Allowthe surface to cure for 4-6 hours before the next phase.Reinforced Joint Detail : Apply 60 mils strip coat ofSikagard 7600HG 6" on each side of the joint. Bridgejoint with 12” Sika Fleece 120 strip pushing it into theSikagard 7600HG . Over reinforcement, apply 60 milsstripe coat of Sikagard 7600 and taper it onto adjacentsurface. Allow the surface to cure for 4-6 hours beforethe next phase.Phase 3 (Coat #1): The first coat of Sikagard 7600 HGshould be applied at the rate of 48 sq.f/1 gal. resultingin 30 dry mils of membrane . Allow to cure (4-6 hours)before proceeding to Phase 4.Phase 4 (Coat #2): Apply the second coat of Sikagard 7600 HG at the rate of 48 sq.ft./1gal. resulting in 30dry mils of membrane.NOTE: If priming is not required skip Phase 1, andproceed with Phase 2 . Any adhesion test is to beperformed 3 days after product application.Sikagard 7600 HG can be applied over horizontal andvertical surface. Apply using a 3/8” roller or notchedsqueege and backroll . Please note that potlife forSikagard 7600 HG is only 30 minutes.Recoat: At 75 F (24 C) and 50 % relative humidity,recoating and multiple or second coats must becompleted within 16 hours of previousapplications of Sikagard 7600 HG. After this 16 hourwindow, it is necessary to abrade, clean and primesurface prior to recoating.Product Data SheetSikagard -7600 HGJanuary 2020, Version 01.030203030200300000124/6Reinforcement: please contact Sika Technical Service(polyester scrim is optional).Removal: Equipment should be immediately cleanedwith an environmentally safe solvent, as permittedunder local regulations.
LIMITATIONS Surfaces must be dry, clean and free of foreign matter.Clear coating may turn opaque and cloudy due tomoisture penetration, especially in exteriorapplications. Surface may be slippery when wet.Containers that have been opened must be used assoon as possible. Do not dilute under anycircumstance. Cured Sikagard 7600 HG may be placed in servicewithin 24 hours for non-aggressive service and nopotable water. Other service applications may requirea cure time of a minimum 96 hours or more. Pleasecontact Sika Technical Service for recommendedapplication. This product is available only in black color. Can beexposed to direct sunlight. Initially after application it isshiny black than after few months it will turn dull afterbeing exposed to direct sunlight. Observe the curing time before immersion into intoand service in potable water. Please see Desinfectionand cleaning guide. To avoid dew point conditions during application,relative humidity must be no more than 95 % andsubstrate temperature must be at least 5 F (3 C)above measured dew point temperatures. Minimum ambient and substrate temperature duringapplication and curing of material is 41 F (5 C);maximum is 95 F (35 C). Surface temperatures mustbe no higher than 110 F (43 C). New concrete must be cured a minimum of 28 daysprior to application . Do not store materials outdoors exposed to sunlightand moisture for prolonged periods. Do not apply to substrate surfaces where moisturevapor transmission will occur during application andcure. This condition should be checked using ASTM D4263 (Polyethylene Sheet method). Substrate must be dry prior to application. Do notapply to a frosted, wet or damp surface. Allowsufficient time for the substrate to dry after rain orinclement weather, as there is the potential forbonding problems. On substrates likely to exhibit outgassing apply duringfalling ambient and substrate temperature. If appliedduring rising temperature pin holing may occur. Do not apply when substrate is in direct sunlight. Precautions should be taken to prevent vapors and/orodors from entering the building/ structure, includingbut not limited to turning off and sealing air intakevents and through-wall air conditioners, and othermeans of vapor/odor ingress during application andcure. Please see Applying within Confined Spacesmanual. Any repairs required to achieve a level surface must beperformed prior to application (consult a Sikarepresentative for guidance on various productsolutions). Surface irregularities may reflect throughthe cured system. When applying over existing coatings or membranescompatibility and adhesion testing, subsequentProduct Data SheetSikagard -7600 HGJanuary 2020, Version 01.030203030200300000125/6approval by Technical Services is required. Do not thin or part mix the material. Do not mixSikagard 7600 HG by hand; mechanically mix only. Unvented metal pan, split/sandwich slab withencapsulated membrane and/or insulation, cinder filldecks, and lightweight insulating concrete overlaysshould not be covered with Sika membrane systemswithout additional deck evaluation to determinesubstrate moisture content and subsequent approvalby Technical Services. If Sikagard 7600 HGis used as split slab waterproofingmembrane or buried membrane cover the final coat ofSikagard 7600 HG with an approved drainage mat(Sika Drain 420) or protection board. Application over asphalt as traffic coating Base Coat:Please contact Sika Technical Service . Always useRecoat primer.BASIS OF PRODUCT DATAResults may differ based upon statistical variationsdepending upon mixing methods and equipment,temperature, application methods, test methods, actualsite conditions and curing conditions.OTHER RESTRICTIONSSee Legal Disclaimer.ENVIRONMENTAL, HEALTH AND SAFETYFor further information and advice regardingtransportation, handling, storage and disposal ofchemical products, user should refer to the actual SafetyData Sheets containing physical, environmental,toxicological and other safety related data. User mustread the current actual Safety Data Sheets before usingany products. In case of an emergency, call CHEMTRECat 1-800-424-9300, International 703-527-3887.LEGAL DISCLAIMER KEEP CONTAINER TIGHTLY CLOSED KEEP OUT OF REACH OF CHILDREN NOT FOR INTERNAL CONSUMPTION FOR INDUSTRIAL USE ONLY FOR PROFESSIONAL USE ONLYPrior to each use of any product of Sika Corporation, itssubsidiaries or affiliates (“SIKA”), the user must alwaysread and follow the warnings and instructions on theproduct’s most current product label, Product DataSheet and Safety Data Sheet which are available atusa.sika.com or by calling SIKA’s Technical ServiceDepartment at 1-800-933-7452. Nothing contained inany SIKA literature or materials relieves the user of theobligation to read and follow the warnings andinstructions for each SIKA product as set forth in thecurrent product label, Product Data Sheet and SafetyData Sheet prior to use of the SIKA product.
SIKA warrants this product for one year from date ofinstallation to be free from manufacturing defects andto meet the technical properties on the current ProductData Sheet if used as directed within the product’s shelflife. User determines suitability of product for intendeduse and assumes all risks. User’s and/or buyer’s soleremedy shall be limited to the purchase price orreplacement of this product exclusive of any labor costs.NO OTHER WARRANTIES EXPRESS OR IMPLIED SHALLAPPLY INCLUDING ANY WARRANTY OFMERCHANTABILITY OR FITNESS FOR A PARTICULARPURPOSE. SIKA SHALL NOT BE LIABLE UNDER ANY LEGALTHEORY FOR SPECIAL OR CONSEQUENTIAL DAMAGES.SIKA SHALL NOT BE RESPONSIBLE FOR THE USE OF THISPRODUCT IN A MANNER TO INFRINGE ON ANY PATENTOR ANY OTHER INTELLECTUAL PROPERTY RIGHTS HELDBY OTHERS.Sale of SIKA products are subject to the Terms andConditions of Sale which are available onditions.htmlor by calling 1-800-933-7452.Sika Corporation201 Polito AvenueLyndhurst, NJ 07071Phone: 1-800-933-7452Fax: 1-201-933-6225usa.sika.comSika Mexicana S.A. de C.V.Carretera Libre Celaya Km. 8.5Fracc. Industrial BalvaneraCorregidora, QueretaroC.P. 76920Phone: 52 442 2385800Fax: 52 442 uct Data SheetSikagard -7600 HGJanuary 2020, Version 01.030203030200300000126/6
It is essential that proper mixing methods and tools are used to ensure proper application of Sikagard -7600 HG. Mixing Drill: Low Speed Mixing Drill ( 400-600 rpm) Mixing Paddle: Jiffy Mixer ( 5-50 Gallon Model) or Mud Mixing Pad
It is essential that proper mixing methods and tools are used to ensure proper application of Sikagard -7600 VG. Mixing Drill: Mechanical Mixer ( 400-600 rpm) Mixing Paddles: Jiffy Style Paddle ( 5-50 Gallon Model) or Mud Mixing Pad
3. Sika MonoTop -723 N / Eco Pore sealer and Levelling Mortar 1. Sikagard -705 L Silane based reactive water repellent impregnation. 2. Sikagard -555 W Elastic Crack bridging protective coating on Sika levelling mortar CONCRETE REPAIR SYSTEMS CONCRETE PROTECTION SYSTEMS 1 2 Sikagard A range of h
Contents v Cisco 7600 Series Ethernet Services 20G Line Card Configuration Guide OL-11907-17 Restrictions and Usage Guidelines 2-112 Troubleshooting 2-118 Configuring Flexible Service Mapping Based on CoS and Ethertype 2-119 Restrictions and Usage Guidelines 2-120 Configuring MultiPoint Brid ging over Ethernet on 7600-ES M-2X10GE and 7600-ESM-20X1GE 2-128 .
Sheet 5 Sheet 6 Sheet 7 Sheet 8 Sheet 9 Sheet 10 Sheet 11 Sheet 12 Sheet 13 Sheet 2 Sheet 1 Sheet 3 Basic Information About Notes Lines and Spaces Trace Notes Stems Note Properties Writing Music Find the Way Home Crossword Puzzle Counting Notes Notes and Beats in 4/4 time Double Puzzle N
Cisco 7600 Series Routers EOL10361 - Amended Cisco announces the end-of-sale and end-of-life dates for the Cisco 7600 Series Routers. The last day to order the affected product(s) is July 24, 2016. Customers with active service contracts will continue to receive support from the Cisco Technical
PLASKOLITE, INC. PRODUCTS: Acrylic Sheet Impact Modified Acrylic Sheet Copolyester Sheet Roll Stock Acrylic Sheet Colored Acrylic Sheet Patterned Sheet High Performance Coatings Thin & Thick Gauge Acrylic Sheet Frosted Acrylic Sheet Acrylic Sheet with Matte Finish Polystyrene Sheet Acrylic Mirror Sheet Acrylic
It appears the E.F. Johnson / Transcrypt 7600 series mobile radios are basically the same as the Icom IC-f420 units. I assume the Icom OPC-617 is equivalent to the Johnson 585-7600-027 cable. Click here to check out the 7600 series service manual to see for
Std. XII : Commerce Adjustments for Reserve Fund, Partner’s Loan Account, Asset taken over by Partner and Contingent Liability *Q.5. A, B and C were partners sharing profits and losses in the ratio of 3 : 2 : 1. On 31st March, 2010, their Balance Sheet was as follows: Balance Sheet as on 31st March, 2010 Liabilities Amount Assets Amount Sundry Creditors 15400 Cash at Bank 3,500 Bills .
