MODEL OL-HRN-RS-HA6 GUIDE ID HA6 AL-XX70-B RS-X70
INSTALL GUIDEMODELOL-HRN-RS-HA6GUIDE IDHA6 AL-XX70-B RS-X70 20210223AVAILABLE ACCESSORIESOL-HRN-RS-PWR(Adapt to any brand remote start w/ BLADE orOL-MDB-ALL / FL-CAN / ADS-AL-CA)VEHICLE COMPATIBILITYFor AL-XX70-B installations see pages 2-9For RS-X70 installations see pages 10-17!DISCLAIMER: The manufacturer of this product nor itsaffiliates accept any responsibility for any electricaldamage to the vehicle or any other connected systems asa result of improper installation of this product. All wiringconnections & vehicle compatibility must be verified by aprofessionally qualified technician prior to aRLXPush-to-Start Sedan 6 Cyl. Automatic2014 - 2015DL-HA61HondaAccordPush-to-Start Hybrid Automatic2013 - 2017DL-HA61HondaAccordPush-to-Start 4/6 Cyl. Automatic2013 - 2017DL-HA61HondaAccordPush-to-Start 4/6 Cyl. Manual2013 - 2017DL-HA62HondaAccord Crosstour Push-to-Start SUV 6 Cyl. Automatic2013 - 2015DL-HA61HondaCivicPush-to-Start 4 Cyl. Automatic2014 - 2015DL-HA61HondaCivicPush-to-Start 4 Cyl. Manual2014 - 2015DL-HA62HondaCR-VPush-to-Start SUV 4 Cyl. Automatic2015 - 2016DL-HA61
INSTALL GUIDEPage 2 of 17MODEL: OL-HRN-RS-HA6AL-XX70-B LayoutC D EIJ KLHGFBAGUIDE ID: HA6 AL-XX70-B RS-X70 20210223ABCDEFGHIWHITE 6 PIN HIGH CURRENT POWER HARNESS (P/N: H-RS6E*)JKLBLADE HARNESS PORT - Use harness from BLADE or an ‘OL-HRN-RS’ T-Harness.WHITE 18 PIN MAIN INPUT/OUTPUT HARNESS (P/N: H-RS18A)RED 4 PIN DOOR LOCK/UNLOCK HARNESS (P/N: DLP-N4)RED 3 PIN REMOTE START HARNESS (P/N: RS-OUTPUT)WHITE 4 PIN AUXILIARY HARNESS (P/N: H-RS4)WHITE 4 PIN PLUG-IN SENSOR PORTS (harness included w/ optional sensors)TEMPERATURE SENSOR - DO NOT COVER(For high/low temp auto start and for automatic low temp crank extender)BLADE CARTRIDGE PORT - For OL-BLADE-AL64 or OL-BLADE-TBGREEN & BLACK DATA PORTS - For Telematics / Data Sensor (Shock, Tilt, etc) / Vehicle Interface Module.(DBI & iDatalink protocols supported on both ports - see ‘Vehicle Learn’ or installer feature #12)ANTENNA / STATUS LIGHT / VALET PORT - Supports compatible plug-in antennas or push-button status light(P/N: AU-LED-PB2)BACKUP BATTERY PORT - Uses standard 9v battery with bracket & plug. Featuring PowerMaze technology - onlysupports security critical functions!AL-XX70-B Installation StepsINSTALLATION STEPS:1) Go to OmegaWeblink.com or use WebLink Mobile to flash the OL-BLADE-AL64 with the firmware matching the vehicle.NOTE: If OEM remote is being used to activate the remote start be sure to enable “Factory keyless RS sequence” as “Lock Lock Lock” OR “Lock Unlock Lock”2) While at OmegaWeblink.com, make sure the AL-XX70-B is updated to v1.5 FW or higher.3) Make all the connections shown in the diagram on the following pages.4) Connect any optional hardware as needed.5) Program the OL-BLADE-AL64 to the vehicle (see “BLADE Programming” on the following pages).6) Perform Vehicle Learn to configure the remote start to match the vehicle (see “AL-XX70-B Programming/Vehicle Learn” on the following pages).NOTE: If Vehicle Learn is not performed remote start operation could fail.7) Test the system for all desired functions.NOTE: Any features NOT supported by the interface module must be hard wired from the remote start to the vehicle. Refer to the remote start install guide and vehicle wiring info atwww.wiresheet.com (only available for authorized dealers) for instructions.
INSTALL GUIDEPage 3 of 17GUIDE ID: HA6 AL-XX70-B RS-X70 20210223MODEL: OL-HRN-RS-HA6Wire Location Chart Diagram AccordAccordCrosstourCivicCR-VTrimPush-to-Start Sedan AutomaticYear2014 - 2015Push-to-Start Hybrid Automatic 2013 - 2017Push-to-Start AutomaticPush-to-Start SUV AutomaticPush-to-Start AutomaticPush-to-Start SUV Automatic2013 - 20172013 - 20152014 - 20152015 - 2016ConnectorColorItemConnectorPinsPin #Wire ColorPolarity-LocationSmart PCU-24 Pin & 28 Pin--12V ConstantWHITE22YELLOW or REDParking LightsBLUE128PINK-Headlight SwitchHornBLUE202ORANGE-Under Steering ColumnSmart PCU-24 Pin & 28 Pin---Left Side Of Steering Column12V ConstantWHITE22GREENParking LightsBLUE128GRAY-Headlight SwitchHornBLUE202LT. BLUE-Under Steering ColumnSmart PCU-24 Pin & 28 Pin---Left Side Of Steering Column12V ConstantWHITE22GREENParking LightsBLUE128GRAY-Headlight SwitchHornBLUE202LT. BLUE-Under Steering Column-Left Side Of Steering Column( )( )( )Left Side Of Steering ColumnPower Relay Box Left Of Steering ColumnFuse BoxFuse BoxSmart PCU-24 Pin & 28 Pin--12V ConstantWHITE22GREEN or WHITEParking LightsBLUE128GRAY-Headlight SwitchHornBLUE202LT.BLUE-Under Steering ColumnSmart PCU-24 Pin & 28 Pin---Right Side Of Steering Column12V ConstantWHITE22RED( )Parking LightsWHITE128GRAY-Headlight SwitchHornBLUE202ORANGE or PINK-Under Steering ColumnSmart PCU-24 Pin & 28 Pin---Behind Glove Compartment12V ConstantWHITE21WHITE( )Parking LightsGRAY128BLUE-Headlight SwitchHornBLUE202TAN or VIOLET-Under Steering Column( )Fuse BoxDash Fuse BoxPower Relay Box Behind Glove Compartment
INSTALL GUIDEPage 4 of 17GUIDE ID: HA6 AL-XX70-B RS-X70 20210223MODEL: OL-HRN-RS-HA6AL-XX70-B Diagram #1D28-PIN SMART PCU ITE16GRAY17BROWN18BLUE/BLACKEVIOLET/WHITE2SMART PCU(see chart for location)C10124-PIN SMART PCU HARNESSBPIN COLOR10ABLACK - GroundOL-HRN-RS-HA6(A)AAN/CHeadlight SwitchConnectorRED - 12V Constant ( ) InputPIN COLOR1GREENN/C2EMPTYN/C3BLUEN/C4PINKN/C 12V ConstantPIN COLOR1BLUEN/C2REDN/C3GREENN/CWHITE/BLACK - Parking Lights (-) OutputOPTIONALOEM Parking LightPIN COLOR1BLUEN/C2REDN/C3GREENN/C6 5 4 3 2 112 11 10 9 8 7GRAY - Connect to supplied hood pin IF no OEM hood pin is presentBLUE/BLACK - OEM Horn (-) OutputPIN COLOR1PINKN/C2WHITE/BLUEN/C3LT. GREEN/REDN/C4LT. GREEN/BLACKN/CBROWN - Siren ( ) OutputOPTIONALOEM HornOPTIONALJREDBLACK Chassis GroundOptionalSiren
INSTALL GUIDEPage 5 of 17GUIDE ID: HA6 AL-XX70-B RS-X70 20210223MODEL: OL-HRN-RS-HA6Wire Location Chart Diagram #2MakeHondaHondaModelAccordCivicTrimPush-to-Start ManualPush-to-Start ManualYear2013 - 20172014 - 2015ConnectorColorItemConnectorPinsPin #Wire ColorPolarity-LocationSmart PCU-24 Pin & 28 Pin--12V ConstantWHITE22GREENParking LightsBLUE128GRAY-Headlight SwitchHornBLUE202LT. BLUE-Under Steering ColumnParking BrakeTAN2819LT. GREEN-Keyless Access Control UnitClutch Bypass-22BROWN-Clutch SwitchSmart PCU-24 Pin & 28 Pin---Right Side Of Steering Column12V ConstantWHITE22RED( )Parking LightsWHITE128GRAY-Headlight SwitchHornBLUE202ORANGE or PINK-Under Steering ColumnParking Brake-11LT. GREEN-Parking Brake SwitchClutch BypassWHITE1613ORANGE-Dash Fuse Box( )Left Of Steering ColumnFuse BoxDash Fuse Box
INSTALL GUIDEPage 6 of 17GUIDE ID: HA6 AL-XX70-B RS-X70 20210223MODEL: OL-HRN-RS-HA6AL-XX70-B Diagram #2D28-PIN SMART PCU ITE16GRAY17BROWN18BLUE/BLACKEVIOLET/WHITE2SMART PCU(see chart for location)C10124-PIN SMART PCU HARNESSBPIN COLOR10ABLACK - GroundOL-HRN-RS-HA6(A)AAHeadlight SwitchConnectorRED - 12V Constant ( ) InputPIN COLOR1GREENN/C2EMPTYN/C3BLUEN/C4PINKN/C 12V ConstantPIN COLORWHITE/BLACK - Parking Lights (-) Output1BLUE2REDN/C3GREENN/C6 5 4 3 2 112 11 10 9 8 7OPTIONALOEM Parking LightBLACK/WHITE - Parking Brake (-) InputParking BrakePIN COLOR1BLUEN/C2REDN/C3GREENN/CGRAY - Connect to supplied hood pin IF no OEM hood pin is presentBLUE/BLACK - OEM Horn (-) OutputPIN COLOR1PINKN/C2WHITE/BLUEN/C3LT. GREEN/REDN/C4LT. GREEN/BLACKN/COPTIONALBLUE - Clutch Bypass (-) OutputBROWN - Siren ( ) OutputOEM HornOPTIONALJClutch BypassREDBLACK Chassis GroundOptionalSiren
INSTALL GUIDEPage 7 of 17MODEL: OL-HRN-RS-HA6AL-XX70-B Optional AccessoriesFAny Add-onSensorSENSOR CABLEIGUIDE ID: HA6 AL-XX70-B RS-X70 20210223DATA CABLEIOL-ADAPTOR-B2GYELLOW - Alarm notification input ( /-)AL-XX70-B MUST have V1.4 or newerfirmware for Linkr-LT compatibility.DATA CABLEGREENPush-Button LED CableKAntenna/LED CableModel: LINKR-LTORwww.omegalinkr.comBLACKORAntenna Cable
INSTALL GUIDEPage 8 of 17GUIDE ID: HA6 AL-XX70-B RS-X70 20210223MODEL: OL-HRN-RS-HA6Blade InstallationSlide Blade into unit.Notice programming button under LED.Ready for Blade Programming Procedure.Blade ProgrammingClose and re-open the driver door towake up the data bus.12ONOFF ACCSTARTTurn ignition to ON position.78ENGINESTARTTSTOPWait, LED will Flash BLUE rapidly.OFFACC6OFF ACCONSTARTTurn ignition to ON position.ONSTARTTurn ignition to OFF position.Wait, LED will turn solid BLUE for 2seconds.910ENGINESTARTTSTOP5 ENGINESTARTTSTOP34WARNING: Do not press Bladeprogramming button.Connect power first.Connect all other remote start connectorsOFFACCONSTARTTurn ignition to OFF position.ENGINESTARTTSTOP WARNING:Disconnect power lastDisconnect remote start from vehicle. Connect remote start to computer andproceed with extended programming.11 x1Press UNLOCK on the OEM remote.!If the vehicle is equipped with powerliftgate, open and close the power liftgatewith the OEM keyfob12 Proceed to AL-XX70-B Programming/Vehicle Learn.
INSTALL GUIDEPage 9 of 17GUIDE ID: HA6 AL-XX70-B RS-X70 20210223MODEL: OL-HRN-RS-HA6AL-XX70-B Programming/Vehicle Learn V1.6 (see installation guide for older versions)Before You Begin:- Make sure all wires/harnesses are connected.- Program the BLADE to the vehicle per the instructions on the previous pages.- Connect any additional accessories/modules to the data ports.- MANUAL TRANSMISSION VEHICLES ONLY: Set the parking brake. The BLACK/WHITE wire must be connected to the parking brake wire.OFF ACC1ONSTARTMANUAL TRANSMISSIONS:Set the parking brake again to enter Manual TransmissionReservation Mode option selection. (installer feature #11)5Turn ignition to ON position (do not start).ENGINESTARTTSTOPWithin 5 seconds of step 1 press the Valet button 3x orsend remote start command (by remote, Linkr, activa2x tion input wire etc.). OR3xOFFACCON 23- The system will chirp & flash the light to indicate currentsetting (default: 2 - Off)- Set and Release the parking brake to scrool through settingoptions.- Chirp confirmation: 1 ON - Shutdown w/ lock, 2 OFF,3 ON - Shutdown w/ door close, 4 ON - Shutdown 10sec. after door close- Before turning the key OFF, perform the MT reservationsequence (see operation guide) and exit the vehicle.- The system will chirp & flash lights to indicate crankdelay (Default: 1 chirp/flash 1.5 sec)- Press valet button to change crank delay- Chirps: 1 1.5 sec, 2 15 sec, 3 20 sec, 4 30 secSTART6 2xStart the engine with the key and let the engine reachnormal idle.- The system will detect data protocols, select the bestavailable engine running detection method, and, learn anyavaialble tach input (data or te remote start (within 60 sec. of Step 4 or 5). Wait untilengine is running and LED flashes slowly(10-45 seconds after engine cranks & runs).Push-to-Start vehicles: Ensure the OEM fob is at least 20 ft.away to allow remote start.ACCONSTART7MANUAL TRANSMISSIONS:Release the parking brake.- This disables VEHICLE LEARN (to enable again, programinstaller feature #2 (bank 10) to “Enabled”.AUTOMATIC TRANSMISSIONS:Turn the ignition key OFF.TO CANCEL/START OVER:Press the valet button once.- The system will chirp & flash the lights equal the #of IGN/ACC/START circuits detected (Max: 4).MANUAL - Proceed to step 5.AUTOMATIC - Skip to step 6.TO SAVE SETTINGS/FINISH VEHICLE LEARN:Press the BRAKE pedal (will shut down RS).8TroubleShooting- See system installation guide for remote start diagnostics and troubleshooting.- See OmegaLink module/firmware guide at www.wiresheet.com for interface module diagnostics and troubleshooting.Programming complete.
INSTALL GUIDEPage 10 of 17MODEL: OL-HRN-RS-HA6RS-X70 LayoutE CGUIDE ID: HA6 AL-XX70-B RS-X70 20210223F D GBAWHITE 6 PIN HIGH CURRENT POWER HARNESS (P/N: H-RS6E*)BWHITE 14 PIN MAIN INPUT/OUTPUT HARNESS (P/N: H-RS14A)CRED 3 PIN DOOR LOCK/UNLOCK HARNESS (P/N: DLP-N3)DRED 3 PIN REMOTE START HARNESS (P/N: RS-OUTPUT)ETEMPERATURE SENSOR - DO NOT COVERFANTENNA / STATUS LIGHT / VALET PORT - Supports compatible plug-in antennas or push-button status lightGGREEN & BLACK DATA PORTS - For Telematics / Data Sensor (Shock, Tilt, etc) / Vehicle Interface Module.(For high/low temp auto start and for automatic low temp crank extender)(P/N: AU-LED-PB2)(DBI & iDatalink protocols supported on both ports - see ‘Vehicle Learn’ or installer feature #12)ARS-X70 Installation StepsINSTALLATION STEPS:1) Go to www.OmegaWeblink.com or use WebLink Mobile to flash the bypass module with the firmware matching the vehicle.NOTE: iDatalink 2-way protocol is recommended for full functionality.NOTE: If OEM remote is being used to activate the remote start be sure “Factory keyless RS sequence” is set to “Lock Lock Lock” OR “Lock Unlock Lock”2) Make all the connections shown in the diagram on the following pages.3) Connect any optional hardware as needed.4) Select Data Mode and program the bypass module to the vehicle (see module programming instructions).5) Perform Vehicle Learn to configure the remote start to match the vehicle.NOTE: If Vehicle Learn is not performed remote start operation could fail.6) Test the system for all desired functions.NOTE: Any features NOT supported by the interface module must be hard wired from the remote start to the vehicle. Refer to the remote start install guide and vehicle wiring info at www.wiresheet.com (only available for authorized dealers) for instructions.
INSTALL GUIDEPage 11 of 17GUIDE ID: HA6 AL-XX70-B RS-X70 20210223MODEL: OL-HRN-RS-HA6Wire Location Chart Diagram AccordAccordCrosstourCivicCR-VTrimPush-to-Start Sedan AutomaticYear2014 - 2015Push-to-Start Hybrid Automatic 2013 - 2017Push-to-Start AutomaticPush-to-Start SUV AutomaticPush-to-Start AutomaticPush-to-Start SUV Automatic2013 - 20172013 - 20152014 - 20152015 - 2016ConnectorColorItemConnectorPinsPin #Wire ColorPolarity-LocationSmart PCU-24 Pin & 28 Pin--12V ConstantWHITE22YELLOW or REDParking LightsBLUE128PINK-Headlight SwitchHornBLUE202ORANGE-Under Steering ColumnSmart PCU-24 Pin & 28 Pin---Left Side Of Steering Column12V ConstantWHITE22GREENParking LightsBLUE128GRAY-Headlight SwitchHornBLUE202LT. BLUE-Under Steering ColumnSmart PCU-24 Pin & 28 Pin---Left Side Of Steering Column12V ConstantWHITE22GREENParking LightsBLUE128GRAY-Headlight SwitchHornBLUE202LT. BLUE-Under Steering Column-Left Side Of Steering Column( )( )( )Left Side Of Steering ColumnPower Relay Box Left Of Steering ColumnFuse BoxFuse BoxSmart PCU-24 Pin & 28 Pin--12V ConstantWHITE22GREEN or WHITEParking LightsBLUE128GRAY-Headlight SwitchHornBLUE202LT.BLUE-Under Steering ColumnSmart PCU-24 Pin & 28 Pin---Right Side Of Steering Column12V ConstantWHITE22RED( )Parking LightsWHITE128GRAY-Headlight SwitchHornBLUE202ORANGE or PINK-Under Steering ColumnSmart PCU-24 Pin & 28 Pin---Behind Glove Compartment12V ConstantWHITE21WHITE( )Parking LightsGRAY128BLUE-Headlight SwitchHornBLUE202TAN or VIOLET-Under Steering Column( )Fuse BoxDash Fuse BoxPower Relay Box Behind Glove Compartment
INSTALL GUIDEPage 12 of 17GUIDE ID: HA6 AL-XX70-B RS-X70 20210223DMODEL: OL-HRN-RS-HA6RS-X70 Diagram #1E10ABLACK - GroundOL-HRN-RS-HA6(A)AA28-PIN SMART PCU HARNESSPIN COLOR1B147ORANGE2WHITE/BLACK3RED/WHITE4LT. GREEN/BLACK N/CN/C9YELLOWN/C10LT. SMART PCU(see chart for location)CN/CB8124-PIN SMART PCU HARNESSRED - 12V Constant ( ) InputHeadlight SwitchConnector 12V Constant1C36 5 4 3 2 112 11 10 9 8 7PIN COLOR1GREENN/C2EMPTYN/C3BLUEN/CWHITE/BLACK - Parking Lights (-) OutputOPTIONALOEM Parking Light1D3GRAY - Connect to supplied hood pin IF no OEM hood pin is presentPIN COLOR1BLUEN/C2REDN/C3GREENN/CBROWN - OEM Horn (-) OutputOPTIONALOEM HornDATA CABLEOL-HRN-RS-HA6(B)G
INSTALL GUIDEPage 13 of 17GUIDE ID: HA6 AL-XX70-B RS-X70 20210223MODEL: OL-HRN-RS-HA6Wire Location Chart Diagram #2MakeHondaHondaModelAccordCivicTrimPush-to-Start ManualPush-to-Start ManualYear2013 - 20172014 - 2015ConnectorColorItemConnectorPinsPin #Wire ColorPolarity-LocationSmart PCU-24 Pin & 28 Pin--12V ConstantWHITE22GREENParking LightsBLUE128GRAY-Headlight SwitchHornBLUE202LT. BLUE-Under Steering ColumnParking BrakeTAN2819LT. GREEN-Keyless Access Control UnitClutch Bypass-22BROWN-Clutch SwitchSmart PCU-24 Pin & 28 Pin---Right Side Of Steering Column12V ConstantWHITE22RED( )Parking LightsWHITE128GRAY-Headlight SwitchHornBLUE202ORANGE or PINK-Under Steering ColumnParking Brake-11LT. GREEN-Parking Brake SwitchClutch BypassWHITE1613ORANGE-Dash Fuse Box( )Left Of Steering ColumnFuse BoxDash Fuse Box
INSTALL GUIDEPage 14 of 17GUIDE ID: HA6 AL-XX70-B RS-X70 20210223MODEL: OL-HRN-RS-HA6RS-X70 Diagram #2D28-PIN SMART PCU HARNESSE10ABLACK - GroundOL-HRN-RS-HA6(A)AAPIN COLOR1B147ORANGE2WHITE/BLACK3RED/WHITE4LT. GREEN/BLACK SMART PCU(see chart for location)CN/CN/C9YELLOWN/C10LT. 24-PIN SMART PCU HARNESSB81RED - 12V Constant ( ) InputHeadlight SwitchConnector 12V Constant1C36 5 4 3 2 112 11 10 9 8 7PIN COLOR1GREENN/C2EMPTYN/C3BLUEN/CWHITE/BLACK - Parking Lights (-) OutputOPTIONALOEM Parking Light1D3GRAY - Connect to supplied hood pin IF no OEM hood pin is presentPIN COLOR1BLUE2REDN/C3GREENN/CBROWN - OEM Horn (-) OutputBLACK/WHITE - Parking Brake (-) InputOPTIONALParking BrakeOEM HornBLUE - Clutch Bypass (-) OutputDATA CABLEOL-HRN-RS-HA6(B)GClutch Bypass
INSTALL GUIDEPage 15 of 17MODEL: OL-HRN-RS-HA6RS-X70 Optional AccessoriesGData ShockSensorSENSOR CABLEBLACKGGUIDE ID: HA6 AL-XX70-B RS-X70 20210223DATA CABLEGOL-ADAPTOR-B2GYELLOW - Alarm notification input ( /-)RS-X70 MUST have V1.4 or newerfirmware for Linkr-LT compatibility.DATA CABLEGREENPush-Button LED CableFAntenna/LED CableModel: LINKR-LTORwww.omegalinkr.comBLACKORAntenna Cable
INSTALL GUIDEPage 16 of 17GUIDE ID: HA6 AL-XX70-B RS-X70 20210223MODEL: OL-HRN-RS-HA6Installation Mode Selection2Press and release programming button1to select installation mode.!LED flashes (1x) once Data Mode (Recommended)LED flashes (2x) twice Hardwire ModePress and hold programming button untilLED turns solid GREEN to register selection.After registration, follow Factory Reset to changeinstallation mode and restart this process.Module ProgrammingClose and re-open the driver door towake up the data bus.12OFF ACCONSTART7Turn ignition to ON position.8WARNING: Do not press moduleprogramming button.Connect power first.Connect all other module connectors OFF ACCONSTARTTurn ignition to ON position.ENGINESTARTTSTOPENGINESTARTTSTOPWait, LED will Flash GREEN rapidly.34OFFACCONSTARTTurn ignition to OFF position.910ENGINESTARTTSTOP56 Wait, LED will turn solid GREEN for 2 seconds.OFFACCONSTARTTurn ignition to OFF position.ENGINESTARTTSTOPWARNING:Disconnect power lastDisconnect module from vehicle.Connect module to computer and proceedwith extended programming.11 x1Press UNLOCK on the OEM remote.!If the vehicle is equipped with powerliftgate, open and close the power liftgatewith the OEM keyfob12 Proceed to RS-X70 Programming/Vehicle Learn.
INSTALL GUIDEPage 17 of 17GUIDE ID: HA6 AL-XX70-B RS-X70 20210223MODEL: OL-HRN-RS-HA6RS-X70 Programming/Vehicle Learn V1.6 (see installation guide for older versions)Before You Begin:- Make sure all wires/harnesses are connected.- Program the bypass module to the vehicle per the instructions on the previous pages.- Connect any additional accessories/modules to the data ports.- MANUAL TRANSMISSION VEHICLES ONLY: Set the parking brake. The BLACK/WHITE wire must be connected to the parking brake wire.OFF ACC1ONSTARTMANUAL TRANSMISSIONS:Set the parking brake again to enter Manual TransmissionReservation Mode option selection. (installer feature #11)5Turn ignition to ON position (do not start).ENGINESTARTTSTOPWithin 5 seconds of step 1 press the Valet button 3x orsend remote start command (by remote, Linkr, activa2x tion input wire etc.). OR3xOFFACCON 23- The system will chirp & flash the light to indicate currentsetting (default: 2 - Off)- Set and Release the parking brake to scrool through settingoptions.- Chirp confirmation: 1 ON - Shutdown w/ lock, 2 OFF,3 ON - Shutdown w/ door close, 4 ON - Shutdown 10sec. after door close- Before turning the key OFF, perform the MT reservationsequence (see operation guide) and exit the vehicle.- The system will chirp & flash lights to indicate crankdelay (Default: 1 chirp/flash 1.5 sec)- Press valet button to change crank delay- Chirps: 1 1.5 sec, 2 15 sec, 3 20 sec, 4 30 secSTART6 2xStart the engine with the key and let the engine reachnormal idle.- The system will detect data protocols, select the bestavailable engine running detection method, and, learn anyavaialble tach input (data or te remote start (within 60 sec. of Step 4 or 5). Wait untilengine is running and LED flashes slowly(10-45 seconds after engine cranks & runs).Push-to-Start vehicles: Ensure the OEM fob is at least 20 ft.away to allow remote start.ACCONSTART7MANUAL TRANSMISSIONS:Release the parking brake.- This disables VEHICLE LEARN (to enable again, programinstaller feature #2 (bank 10) to “Enabled”.AUTOMATIC TRANSMISSIONS:Turn the ignition key OFF.TO CANCEL/START OVER:Press the valet button once.- The system will chirp & flash the lights equal the #of IGN/ACC/START circuits detected (Max: 4).MANUAL - Proceed to step 5.AUTOMATIC - Skip to step 6.TO SAVE SETTINGS/FINISH VEHICLE LEARN:Press the BRAKE pedal (will shut down RS).8TroubleShooting- See system installation guide for remote start diagnostics and troubleshooting.- See OmegaLink module/firmware guide at www.wiresheet.com for interface module diagnostics and troubleshooting.Programming complete.
Honda Accord Crosstour Push-to-Start SUV 6 Cyl. Automatic 2013 - 2015 DL-HA6 1 Honda Civic Push-to-Start 4 Cyl. Automatic 2014 - 2015 DL-HA6 1 Honda Civic Push-to-Start 4 Cyl. Manual 2014 - 2015 DL-HA6 2 Honda CR-V Push-to-Start SUV 4 Cyl. Automatic 2015 - 2016 DL-HA6 1 Make Model Trim Year
D GB F E 1 09912-09.2013-DGbFEI engineering for a better world GEA Refrigeration Technologies Bock Compressor HA6 Assembly instructions HA6/1080-4 HA
Covers 400 Chrylser, Dodge, & Jeep models OL-HRN-RS-FM3 Covers 128 Ford, Lincoln, models OL-HRN-RS-FM2 Covers 214 Ford, Lincoln, Mazda, & Mercury models OL-HRN-RS-GM7 Covers 237 Buick, Chevrolet, & GMC models OL-HRN-RS-GM10 Covers 495 Buick, Cadillac, Chevrolet, Hummer, GMC, . Jeep Commander: Std. Key 6 Cyl. Automatic 2008 -
(ISO 3536:2016) HRN ISO 6460-1:2012/A1:2017 en pr Motocikli – Metoda mjerenja emisija ispušnih plinova . HRN EN ISO 4254-12:2013/A1:2017 en pr Poljoprivredna mehanizacija – Sigurnost – 12. dio: . HRN ISO 21940-2:2017 en pr Mehaničke vibracije – Uravnoteživanje rotora – 2. dio: Terminološki rječnik (ISO 21940-2:2017) .
HRN EN ISO 6974-5: 2014 – rezultati mjerenja: Molni sastav normaliziran na tri decimale Molni sastav s pripadnom proširenom mjernom nesigurnošću* S as v M oln iu (be raka) N 2 0,622 CO 0,116 C 1 97,666 C 2 ,169 0,308 i-C 4 0,050 n-C 4 0,047 i-C 5 0,007 n-C 5 0,007 C 6 0,008. HRN EN ISO 6976:2016 – rezultati proračuna s pripadajućim .
HRN EN 55014-1 (CISPR 14-1; EN 55014-1) Točka/Clause 5 3. Mjerenje snage smetnji zračenja Measurement of disturbance power HRN EN 55014-1 (CISPR 14-1; EN 55014-1) Točka/Clause 6 4. Oprema inf
Hofmarcher, M.; Perić, N.; Simon, J. (2017) Priority setting methods in health information, BRIDGE Health Technical Report 04/2017 on Recommendations of priority setting methods for an European Research Infrastructure Consortium on Health Information for Research and Evidence-based Policy (HIREP-ERIC), HS&I and Medical University of Vienna.
Remington Model 121 Fieldmaster Remington Model 141 Remington Model 241 Remington 270 Remington 336 Remington Model 504 Remington Model 511 Scoremaster Remington Model 512 Sportmaster Remington Model 513 Remington Model 572 Fieldmaster . Remington Model 600 Remington Model 660 Remington Model 673 Remington
Before accepting an appointment to continue a project started by someone else, the member should inform the previous appointee and also ascertain from the potential client: that the previous appointment has been properly determined; and the client holds a licence to use any information, including drawings, specifications, calculations and the like, prepared by the preceding appointee; and that .
