TTL-232R TTL To USB Serial Converter Range Of Cables Datasheet
TTL-232R TTL TO USB SERIAL CONVERTER RANGE OF CABLES DatasheetVersion 2.04Document No.: FT 000054 Clearance No.: FTDI# 53Future Technology Devices International LtdTTL-232RTTL to USB Serial Converter Range ofCablesDatasheetNeither the whole nor any part of the information contained in, or the product described in this manual, may be adapted or reproducedin any material or electronic form without the prior written consent of the copyright holder. This product and its documentation aresupplied on an as-is basis and no warranty as to their suitability for any particular purpose is either made or implied. Future TechnologyDevices International Ltd will not accept any claim for damages howsoever arising as a result of use or failure of this product. Yourstatutory rights are not affected. This product or any variant of it is not intended for use in any medical appliance, device or system inwhich the failure of the product might reasonably be expected to result in personal injury. This document provides preliminar yinformation that may be subject to change without notice. No freedom to use patents or other intellectual property rights is implied bythe publication of this document. Future Technology Devices International Ltd, Unit 1, 2 Seaward Place, Centurion Business Park,Glasgow G41 1HH United Kingdom. Scotland Registered Company Number: SC136640Copyright Future Technology Devices International Limited1
TTL-232R TTL TO USB SERIAL CONVERTER RANGE OF CABLES DatasheetVersion 2.04Document No.: FT 000054 Clearance No.: FTDI# 531 DescriptionThe TTL-232R cables are a family of USB to TTL serial UART converter cables incorporating FTDI’sFT232RQ USB to Serial UART interface IC device which handles all the USB signalling and protocols. Thecables provide a fast, simple way to connect devices with a TTL level serial interface to USB.Each TTL-232R cable contains a small internal electronic circuit board, utilising the FT232R, which isencapsulated into the USB connector end of the cable. The FT232R datasheet, DS FT232R, is available athttp://www.ftdichip.com. The other end of the cable comes with a selection of different connectorssupporting various applications – see Table 1.1Cables are FCC, CE, RoHS compliant and are available at TTL levels of 5V and 3.3V.Cables are available with either a 6-way SIL,0.1” pitch connector, a 3.5mm Audio Jack, an 8 way, keyed2mm pitch connector (intended for use with VMUSIC2 or VDRIVE2) or bare, tinned wire endedconnections (see Table 1.1)The USB side of the cable is USB powered and USB 2.0 full speed compatible. Each cable is 1.8m longand supports a data transfer rate up to 3 Mbaud. Each cable supports the FTDIChip-ID , with a uniqueUSB serial number programmed into the FT232R. This feature can be used to create a security orpassword protected file transfer access using the cable. Further information and examples on this featureare available at http://www.ftdichip.com under FTDIChip-ID Projects.The TTL-232R cables require USB drivers, available free from http://www.ftdichip.com, which areused to make the FT232R in the cable appear as a virtual COM port (VCP). This then allows the user tocommunicate with the USB interface via a standard PC serial emulation port (for example TTY). AnotherFTDI USB driver, the D2XX driver, can also be used with application software to directly access theFT232R on the cable though a DLL. This is illustrated in the Figure 1.1Various ConnectorOptionsVCPTTYWire EndedTTL-232R3mm Audio Jack6 way, 0.1" Single In Line connectorUSBVirtual COM Port8 way, Keyed,2mm, Single In LineconnectorVarious ConnectorOptionsWire EndedD2XXDLLTTY3mm Audio JackUSB6 way, 0.1" Single In Line connector8 way, Keyed,2mm, Single In LineconnectorSoftware application access to USB via D2XXFigure 1.1 Using the TTL-232R CableCopyright Future Technology Devices International Limited2
TTL-232R TTL TO USB SERIAL CONVERTER RANGE OF CABLES DatasheetVersion 2.04Document No.: FT 000054 Clearance No.: FTDI# 531.1 Available Cables and Part NumbersThe following Table 1.1 gives details of the available TTL-232R cables.Part NumberTTL-232R-5V**TTL-232R-3V3DescriptionUSB to UART cable with 5V TTL levelUART signals.USB to UART cable with 3.3V TTL levelUART signals.End Connector*Cable details6 core, UL24646 pin SIL, 0.1” pitch24 AWG,diam 5mm6 core, UL24646 pin SIL, 0.1” pitch24 AWG,diam 5mmTTL-232R-5V-USB to UART cable with 5V TTL levelWire Ended (noWE**UART signals.connector)TTL-232R-3V3-USB to UART cable with 3.3V TTL levelWire Ended (noWEUART signals.connector)TTL-232R-5V-USB to UART cable with 5V TTL levelAJ**UART signals.6 core, UL246424 AWG,diam 5mm6 core, UL246424 AWG,diam 5mm2 core and spiral,3.5mm Audio Jack24 AWGdiam 5mm2 core and spiral,TTL-232R-3V3-USB to UART cable with 3.3V TTL levelAJUART signals.3.5mm Audio Jack24 AWGdiam 5mm8 way, keyed, 2mmTTL-232R-3V3-USB to UART cable with 3.3V TTL levelconnector for use2mmUART signals.with FTDI VDRIVE2or VMUSIC2 modules7 core, UL246426 AWG,diam 5mmTable 1.1 TTL-232R Cables Descriptions and Part Numbers*FTDI supports customised end connector designs. For more information, please contact FTDI Sales Team(sales1@ftdichip.com)**These cables are identical to cables which do not have the “5V” in the part number. The 5V was added to the partnumber for clarity.Copyright Future Technology Devices International Limited3
TTL-232R TTL TO USB SERIAL CONVERTER RANGE OF CABLES DatasheetVersion 2.04Document No.: FT 000054 Clearance No.: FTDI# 531.2 CertificationsFTDI TTL-232R range of cables are fully RoHs compliant as well as CE and FCC certified (with theexception of the TTL-232R-XX-WE cables which have not yet completed FCC and CE testing).1.3 USB CompliantThe TTL-232R cables are fully compliant with the USB 2.0 specification.Copyright Future Technology Devices International Limited4
TTL-232R TTL TO USB SERIAL CONVERTER RANGE OF CABLES DatasheetVersion 2.04Document No.: FT 000054 Clearance No.: FTDI# 53Table of Contents12Description . 21.1Available Cables and Part Numbers. 31.2Certifications . 41.3USB Compliant . 4Typical Applications . 72.1Driver Support . 72.2Features . 83Features of FT232R applicable toTTL-232R Cables . 94TTL-232R-5V and TTL-232R-3V3 Cables . 114.1 TTL-232R-5V, TTL-232R-3V3 Connector Pin Out and Mechanicaldetails . 1154.2TTL-232R-5V and TTL-232R-3V3 Cable Signal Descriptions . 114.3TTL-232R-5V and TTL-232R-3V3 Electrical Parameters. 124.3.1TTL-232R-5V Electrical Parameters . 124.3.2TTL-232R-3V3 Electrical Parameters . 12TTL-232R-5V-AJ and TTL-232R-3V3-AJ . 145.1 TTL-232R-5V-AJ, TTL-232R-3V3-AJ Connector Pin Out andMechanical details . 145.2 TTL-232R-5V-AJ and TTL-232R-3V3-AJ Cable SignalDescriptions . 155.36TTL-232R-5V-AJ and TTL-232R-3V3-AJ Electrical Parameters 155.3.1TTL-232R-5V-AJ Electrical Parameters . 155.3.2TTL-232R-3V3-AJ Electrical Parameters . 15TTL-232R-5V-WE and TTL-232R-3V3-WE Cables . 176.1 TTL-232R-5V-WE, TTL-232R-3V3-WE Connections andMechanical Details. 176.2 TTL-232R-5V-WE and TTL-232R-3V3-WE Cable SignalDescriptions . 176.37TTL-232R-5V-WE and TTL-232R-3V3-WE Electrical Parameters186.3.1TTL-232R-5V-WE Electrical Parameters . 186.3.2TTL-232R-3V3-WE Electrical Parameters . 18TTL-232R-3V3-2mm Cables . 20Copyright Future Technology Devices International Limited5
TTL-232R TTL TO USB SERIAL CONVERTER RANGE OF CABLES DatasheetVersion 2.04Document No.: FT 000054 Clearance No.: FTDI# 537.1TTL-232R-3V3-2mm Connector Pin Out and Mechanical details207.2TTL-232R-3V3-2mm Cable Signal Descriptions . 217.3TTL-232R-3V3-2mm Electrical Parameters . 218Cable PCB Circuit Schematic . 239Contact Information . 24Appendix A - Cable EEPROM Configuration. 25Appendix B - References . 27Document References . 27Acronyms and Abbreviations . 27Appendix C - List of Figures and Tables . 28List of Figures . 28List of Tables . 28Appendix D - Revision History . 29Copyright Future Technology Devices International Limited6
TTL-232R TTL TO USB SERIAL CONVERTER RANGE OF CABLES DatasheetVersion 2.04Document No.: FT 000054 Clearance No.: FTDI# 532 Typical Applications USB to Serial TTL Level Converter Upgrading Legacy Peripherals to USB Interface Microcontroller UART or I/O to USB Interface FPGA / PLD to USB Interface to FTDI VDRIVE2 or VMUSIC2modules.2.1 Replace MAX232 type level shifters allowing fordirect connection of products to PC via USB USB Instrumentation PC interface USB Industrial Control USB Software / Hardware Encryption DonglesDriver SupportRoyalty free VIRTUAL COM PORTRoyalty free D2XX Direct Drivers(VCP) DRIVERS for.(USB Drivers DLL S/W Interface) Windows 10 32,64-bit Windows 10 32,64-bit Windows 8/8.1 32,64-bit Windows 8/8.1 32,64-bit Windows 7 32,64-bit Windows 7 32,64-bit Windows Vista and Vista 64-bit Windows Vista and Vista 64-bit Windows XP and XP 64-bit Windows XP and XP 64-bit Windows 98, 98SE, ME, 2000, Server 2003, XP,Server 2008 and server 2012 R2 Windows 98, 98SE, ME, 2000, Server 2003, XP,Server 2008 and server 2012 R2 Windows XP Embedded Windows XP Embedded Windows CE 4.2, 5.0 and 6.0 Windows CE 4.2, 5.0 and 6.0 Mac OS 8/9, OS-X Linux 2.4 and greater Linux 2.4 and greater Android (J2xx)The drivers listed above are all available to download for free from www.ftdichip.com Various 3rd PartyDrivers are also available for various other operating systems - see www.ftdichip.com for details.Copyright Future Technology Devices International Limited7
TTL-232R TTL TO USB SERIAL CONVERTER RANGE OF CABLES DatasheetVersion 2.04Document No.: FT 000054 Clearance No.: FTDI# 532.2Features TTL-232R Converter Cable provides a USB toTTL Serial interface with various endconnectors. Support for FT232R FTDIChip-ID feature forimproved security. On board FT232RQ provides single chip USB toasynchronous serial data transfer interface. 5V or 3.3V output allows external logic to bepowered from the USB port. Entire USB protocol handled by the electronicsin the cable USB. 6 way outputs provide Tx, Rx, RTS#, CTS#,VCC and GND (except Audio Jack whichprovides only TX,RX and GND). Connect directly to a microcontroller UART orI/O pins. 8 way, keyed connector to support FTDIVDRIVE2 and VMUSIC2. UART interface support for 7 or 8 data bits, 1or 2 stop bits and odd / even / mark / space /no parity. 3 way Audio Jack connector provides Tx, Rxand GND.Fully assisted hardware (RTS#/CTS#) or X-On/ X-Off software handshaking. Low USB bandwidth consumption. UHCI / OHCI / EHCI host controller compatible. Data transfer rates from 300 baud to 3 Mbaudat TTL levels. USB 2.0 Full Speed compatible. -40 C to 85 C operating temperature range. Internal EEPROM with user writeable area. Cable length is 1.80m (6 feet). 5V CMOS drive outputs and 5V safe TTL inputsmakes the TTL-232R easy to interface to 5VMCU’s. FCC and CE compliant. Custom versions also available (subject toMOQ). FTDI’s royalty-free VCP allow forcommunication as a standard emulated COMport and D2XX ‘direct’ drivers provide DLLapplication programming interface.Copyright Future Technology Devices International Limited8
TTL-232R TTL TO USB SERIAL CONVERTER RANGE OF CABLES DatasheetVersion 2.04Document No.: FT 000054 Clearance No.: FTDI# 533 Features of FT232R applicable toTTL-232R CablesThe TTL-232R cables use FTDI’s FT232RQ USB to serial IC device. This section summarises the keyfeatures of the FT232RQ which apply to the TTL-232R USB to serial TTL converter cables. For furtherdetails, and a full features and enhancements description consult the FT232R datasheet, this is availablefrom www.ftdichip.com.Internal EEPROM. The internal EEPROM in each cable is used to store USB Vendor ID (VID), Product ID(PID), device serial number, product description string and various other USB configuration descriptors.Each cable is supplied with the internal EEPROM pre-programmed as described in Contact InformationHead Office – Glasgow, UKBranch Office – Tigard, Oregon, USAFuture Technology Devices International LimitedUnit 1, 2 Seaward Place, Centurion Business ParkGlasgow G41 1HHUnited KingdomTel: 44 (0) 141 429 2777Fax: 44 (0) 141 429 2758Future Technology Devices International Limited (USA)7130 SW Fir LoopTigard, OR 97223-8160USATel: 1 (503) 547 0988Fax: 1 (503) 547 0987E-mail (Sales)E-mail (Support)E-mail (General Enquiries)E-mail (Sales)E-mail (Support)E-mail (General @ftdichip.comus.admin@ftdichip.comBranch Office – Taipei, TaiwanBranch Office – Shanghai, ChinaFuture Technology Devices International Limited (Taiwan)2F, No. 516, Sec. 1, NeiHu RoadTaipei 114Taiwan, R.O.C.Tel: 886 (0) 2 8797 1330Fax: 886 (0) 2 8791 3576Future Technology Devices International Limited (China)Room 1103, No. 666 West Huaihai Road,Shanghai, 200052ChinaTel: 86 21 62351596Fax: 86 21 62351595E-mail (Sales)E-mail (Support)E-mail (General Enquiries)E-mail (Sales)E-mail (Support)E-mail (General n.support@ftdichip.comcn.admin@ftdichip.comWeb Sitehttp://ftdichip.comDistributor and Sales RepresentativesPlease visit the Sales Network page of the FTDI Web site for the contact details of our distributor(s) and salesrepresentative(s) in your country.System and equipment manufacturers and designers are responsible to ensure that their systems, and any Future Technology DevicesInternational Ltd (FTDI) devices incorporated in their systems, meet all applicable safety, regulatory and system-level performancerequirements. All application-related information in this document (including application descriptions, suggested FTDI devices and othermaterials) is provided for reference only. While FTDI has taken care to assure it is accurate, this information is subject to customerconfirmation, and FTDI disclaims all liability for system designs and for any applications assistance provided by FTDI. Use of FTDIdevices in life support and/or safety applications is entirely at the user’s risk, and the user agrees to defend, indemnify and holdharmless FTDI from any and all damages, claims, suits or expense resulting from such use. This document is subject to change withoutnotice. No freedom to use patents or other intellectual property rights is implied by the publication of this document. Neith er the wholenor any part of the information contained in, or the product described in this document, may be adapted or reproduced in any materialor electronic form without the prior written consent of the copyright holder. Future Technology Devices International Ltd, Un it 1, 2Seaward Place, Centurion Business Park,Copyright Future Technology Devices International Limited9
TTL-232R TTL TO USB SERIAL CONVERTER RANGE OF CABLES DatasheetVersion 2.04Document No.: FT 000054 Clearance No.: FTDI# 53Appendix A - Cable EEPROM Configuration.A user area of the internal EEPROM isavailable to system designers to allow storing additional data. The internal EEPROM descriptors can beprogrammed in circuit, over USB without any additional voltage requirement. It can be programmedusing the FTDI utility software called FT PROG, which can be downloaded from FTDI Utilities on the FTDIwebsite (www.ftdichip.com).Lower Operating and Suspend Current. The FT232R has a low 15mA operating supply current and avery low USB suspend current of approximately 70μA. (Note that during suspend mode, the currentdrawn by application should not exceed 2.5mA to remain USB compliant)Low USB Bandwidth Consumption. The USB interface of the FT232R, and therefore the TTL-232Rcables has been designed to use as little as possible of the total USB bandwidth available from the USBhost controller.High Output Drive Option. The UART interface I/O pins on the TTL-232R cables (RXD, TXD, RTS#, andCTS#) can be configured to use the FT232R’s high output drive option. This option allows the FT232R I/Opins to drive up to three times the standard signal drive level. This allows multiple devices to be driven,or devices that require a greater signal drive strength to be interfaced to the cables. This option isenabled in the internal EEPROM.UART Pin Signal Inversion. The sense of each of the eight UART signals can be individually inverted byconfiguring options in the internal EEPROM. For example CTS# (active low) can be changed to CTS(active high), or TXD can be changed to TXD#.FTDIChip-ID . The FT232R includes the new FTDIChip-ID security dongle feature. This FTDIChip-ID feature allows a unique number to be burnt into each cable during manufacture. This number cannot bereprogrammed. This number is only readable over USB can be used to form the basis of a security donglewhich can be used to protect any customer application software being copied. This allows the possibilityof using the TTL-232R cables as a dongle for software licensing. Further to this, a renewable licensescheme can be implemented based on the FTDIChip-ID number when encrypted with other information.This encrypted number can be stored in the user area of the FT232R internal EEPROM, and can bedecrypted, then compared with the protected FTDIChip-ID to verify that a license is valid. Web basedapplications can be used to maintain product licensing this way. An application note, AN232R-02,available from FTDI website (www.ftdichip.com) describes this feature.Improved EMI Performance. The TTL-232R cables are FCC and CE certified.Extended Operating Temperature Range - The TTL-232R cables are capable of operating over anextended temperature range of -40º to 85º C thus allowing them to be used in automotive or industrialapplications.Copyright Future Technology Devices International Limited10
TTL-232R TTL TO USB SERIAL CONVERTER RANGE OF CABLES DatasheetVersion 2.04Document No.: FT 000054 Clearance No.: FTDI# 534 TTL-232R-5V and TTL-232R-3V3 CablesThe TTL-232R-5V and TTL-232R-3V3 cables are both terminated by a 6 way, 0.1”, Single-In-Line (SIL)connector. The difference between the two cables is that the TTL-232R-5V operates at 5V levels (signalsand power supply) and the TTL-232R-3V3 operates at 3.3V levels (signals only, VCC 5V).TTL-232R-5V, TTL-232R-3V3Mechanical details4.1ConnectorPinOutand6 pin header0.1in D55RTS#66CABLE 1.8mYELLOWGREENFigure 4.1 TTL-232R-5V and TTL-232R-3V3, 6 Way Header Pin OutThe mechanical details of the 6 way connector are shown in the following diagramDimensions (mm)APin 1BCEA2.54 /- 0.05B12.70 /- 0.2CD15.24 /- 0.2D14.0 /- 0.2E2.54 /- 0.05Figure 4.2 TTL-232R-5V TTL-232R-3V3, 6 Way Header Mechanical Details4.2TTL-232R-5V and TTL-232R-3V3 Cable Signal DescriptionsHeader PinNameTypeColour1GNDGNDBlackDevice ground supply pin.2CTS#InputBrownClear to Send Control input / Handshake signal.3VCCOutputRedNumberDescription 5V output,Copyright Future Technology Devices International Limited11
TTL-232R TTL TO USB SERIAL CONVERTER RANGE OF CABLES DatasheetVersion 2.04Document No.: FT 000054 Clearance No.: FTDI# 53Header it Asynchronous Data output.5RXDInputYellowReceive Asynchronous Data input.6RTS#OutputGreenRequest To Send Control Output / Handshake signal.NumberTable 4.1 TTL-232R-5V and TTL-232R-3V3 Cable Signal DescriptionsTTL-232R-5V and TTL-232R-3V3 Electrical Parameters4.34.3.1 TTL-232R-5V Electrical mUnitsConditionsDependant on theVCCOutput PowerVoltage4.255.05.25VUSB port that theTTL-232R-5V isconnected toIOTOutput PowerCurrentMust be less than--75mA2.5mA duringsuspend.OperatingTemperature Range-40- 85oCTable 4.2 TTL-232R-5V I/O Operating mUnitsConditionsVohOutput Voltage High3.24.14.9VI source 2mAVolOutput Voltage Low0.30.40.6VI sink 2mA1.01.21.5V202530mVVinVHysInput SwitchingThresholdInput SwitchingHysteresisTable 4.3 TTL-232R-5V I/O Pin Characteristics4.3.2 TTL-232R-3V3 Electrical mUnitsConditionsDependant on theVCCOutput Power Voltage4.255.05.25VUSB port that theTTL-232R-3V3 isconnected toCopyright Future Technology Devices International Limited12
TTL-232R TTL TO USB SERIAL CONVERTER RANGE OF CABLES DatasheetVersion 2.04Document No.: FT 000054 Clearance No.: FTDI# 53Must be less thanIOOutput Power Current--75mA2.5mA duringsuspend.TOperatingTemperature Range-40- 85oCTable 4.4 TTL-232R-3V3 I/O Operating mUnitsConditionsVohOutput Voltage High2.22.83.2VI source 3mAVolOutput Voltage Low0.30.40.6VI sink 8mA1.01.21.5V202530mVVinVHysInput SwitchingThresholdInput SwitchingHysteresisTable 4.5 TTL-232R-3V3 I/O Pin CharacteristicsCopyright Future Technology Devices International Limited13
TTL-232R TTL TO USB SERIAL CONVERTER RANGE OF CABLES DatasheetVersion 2.04Document No.: FT 000054 Clearance No.: FTDI# 535 TTL-232R-5V-AJ and TTL-232R-3V3-AJThe TTL-232R-5V-AJ and TTL-232R-3V3-AJ cables are both terminated by a standard 3.5mm Audio Jack(AJ) connector. The difference between the two cables is that the TTL-232R-5V-AJ operates at 5V levels(signals and power supply) and the TTL-232R-3V3-AJ operates at 3.3V levels (signals and powersupply). On these cables the VCC power is not transferred.5.1TTL-232R-5V-AJ, TTL-232R-3V3-AJ Connector Pin Out andMechanical detailsGND1BLACKCABLE 1.8mORANGE TXD4RXD5YELLOW3.5mm Audio JackFigure 5.1 TTL-232R-5V and TTL-232R-3V3, -AJ Pin OutThe mechanical details of the Audio Jack connector are shown in the following Figure 5.2.3.0 /- 0.13.2 /- 0.12.6 /- 0.16.0 /- 0.13.5 /- 0.114.0 /- 0.2Dimensions in mmFigure 5.2 TTL-232R-5V-AJ and TTL-232R-3V3-AJ Audio Jack Mechanical DetailsCopyright Future Technology Devices International Limited14
TTL-232R TTL TO USB SERIAL CONVERTER RANGE OF CABLES DatasheetVersion 2.04Document No.: FT 000054 Clearance No.: FTDI# 53TTL-232R-5V-AJDescriptions5.2Header putReceive Asynchronous Data ransmit Asynchronous Data output.Table 5.1 TTL-232R-5V-AJ and TTL-232R-3V3-AJ Cable Signal DescriptionsTTL-232R-5V-AJ and TTL-232R-3V3-AJ Electrical Parameters5.35.3.1 TTL-232R-5V-AJ Electrical ParametersParameterIOTDescriptionOutput st be less than-75mA2.5mA duringsuspend.OperatingTemperature Range-40 85oCTable 5.2 TTL-232R-5V-AJ I/O Operating mUnitsConditionsVohOutput Voltage High3.24.14.9VI source 6mAVolOutput Voltage Low0.30.40.6VI sink 6mA1.01.21.5V202530mVVinVHysInput SwitchingThresholdInput SwitchingHysteresisTable 5.3 TTL-232R-5V-AJ I/O Pin Characteristics5.3.2 TTL-232R-3V3-AJ Electrical ParametersParameterIOTDescriptionOutput st be less than-75mA2.5mA duringsuspend.OperatingTemperature Range-40 85oCTable 5.4 TTL-232R-3V3-AJ I/O Operating ParametersCopyright Future Technology Devices International Limited15
TTL-232R TTL TO USB SERIAL CONVERTER RANGE OF CABLES DatasheetVersion 2.04Document No.: FT 000054 Clearance No.: FTDI# nditionsVohOutput Voltage High2.22.83.2VI source 3mAVolOutput Voltage Low0.30.40.6VI sink 8mA1.01.21.5V202530mVVinVHysInput SwitchingThresholdInput SwitchingHysteresisTable 5.5 TTL-232R-3V3-AJ I/O Pin CharacteristicsCopyright Future Technology Devices International Limited16
TTL-232R TTL TO USB SERIAL CONVERTER RANGE OF CABLES DatasheetVersion 2.04Document No.: FT 000054 Clearance No.: FTDI# 536 TTL-232R-5V-WE and TTL-232R-3V3-WE CablesThe TTL-232R-5V-WE and TTL-232R-3V3-WE cables are both un-terminated; they are bare and tinnedwires. The difference between the two cables is that the TTL-232R-5V-WE operates at 5V levels (signalsand power supply) and the TTL-232R-3V3-WE operates at 3.3V levels (signals only, VCC 5V).6.1TTL-232R-5V-WE,Mechanical DetailsTTL-232R-3V3-WEConnectionsandThe following Figure 6.1 shows the cable signals and the wire colours for these signals on the TTL-232R5V-WE and TTL-232R-3V3-WE RXD55YELLOWRTS#66GREENCABLE 1.8mFigure 6.1 TTL-232R-5V-WE and TTL-232R-3V3-WE ConnectionsFigure 6.2 TTL-232R-5V-WE and TTL-232R-3V3-WE Mechanical Details (dimensions in CableColourNameTypeDescriptionBlackGNDGNDDevice ground supply pin.BrownCTS#InputClear to Send Control input / Handshake signal.RedVCCOutput 5V outputOrangeTXDOutputTransmit Asynchronous Data output.YellowRXDInputGreenRTS#OutputSignalReceive Asynchronous Data input.Request To Send Control Output / Handshake signal.Table 6.1 TTL-232R-5V-WE and TTL-232R-3V3-WE Cable Signal DescriptionsCopyright Future Technology Devices International Limited17
TTL-232R TTL TO USB SERIAL CONVERTER RANGE OF CABLES DatasheetVersion 2.04Document No.: FT 000054 Clearance No.: FTDI# ctrical6.3.1 TTL-232R-5V-WE Electrical mUnitsConditionsDependant on theVCCOutput PowerVoltage4.255.05.25VUSB port that theTTL-232R-5V-WE isconnected toIOTOutput PowerCurrentMust be less than-75mA2.5mA duringsuspend.OperatingTemperature Range-40 85oCTable 6.2 TTL-232R-5V-WE I/O Operating mUnitsConditionsVohOutput Voltage High3.24.14.9VI source 6mAVolOutput Voltage Low0.30.40.6VI sink 6mA1.01.21.5V202530mVVinVHysInput SwitchingThresholdInput SwitchingHysteresisTable 6.3 TTL-232R-5V-WE I/O Pin Characteristics6.3.2 TTL-232R-3V3-WE Electrical mUnitsConditionsDependant on theVCCOutput PowerVoltage4.255.05.25VUSB port that theTTL-232R-3V3-WE isconnected toIOTOutput PowerCurrentMust be less than-75mA2.5mA duringsuspend.OperatingTemperature Range-40 85oCTable 6.4 TTL-232R-3V3-WE I/O Operating ParametersCopyright Future Technology Devices International Limited18
TTL-232R TTL TO USB SERIAL CONVERTER RANGE OF CABLES DatasheetVersion 2.04Document No.: FT 000054 Clearance No.: FTDI# nditionsVohOutput Voltage High2.22.83.2VI source 3mAVolOutput Voltage Low0.30.40.6VI sink 8mA1.01.21.5V202530mVVinVHysInput SwitchingThresholdInput SwitchingHysteresisTable 6.5 TTL-232R-3V3-WE I/O Pin CharacteristicsCopyright Future Technology Devices International Limited19
TTL-232R TTL TO USB SERIAL CONVERTER RANGE OF CABLES DatasheetVersion 2.04Document No.: FT 000054 Clearance No.: FTDI# 537 TTL-232R-3V3-2mm CablesThe TTL-232R-3V3-2mm cable is terminated by an 8 way, 2mm pitch, Single-In-Line (SIL) keyedconnector. The TTL-232R-3V3-2mm operates at 3.3V levels (signals and power supply). These cablesare primarily intended for interfacing the FTDI VDRIVE2 and VMUSIC2 modules.Note that when connected to VDRIVE2 or VMUSIC2 module, the TTL-232R-3V3-2mm cable 8-wayconnector pin 1 connects to pin 8 of the module, and pin 8 of the cable connects to pin 1 of the Mechanical8 pin header2mm pitchVCCGND18CTS#7VCC6TXD5,1RXD4RTS#3BLUE2CABLE 1.8mKEY345678GREENYELLOWORANGEREDBROWNBLACKFigure 7.1 TTL-232R-3V3-2mm, 8 Way Header Pin OutThe mechanical details of the 2mm pitch 8 way, keyed, connector are shown in the following diagramDimensions (mm)BPin 1ACA2.00 /- 0.005B14.00 /- 0.2EC16.40 /- 0.2D7.10 /- 0.25E2.00 /- 0.005DFigure 7.2 TTL-232R-3V3-2mm, 2mm pitch, Keyed, 8 way Header Mechanical DetailsCopyright Future Technology Devices International Limited20
TTL-232R TTL TO USB SERIAL CONVERTER RANGE OF CABLES DatasheetVersion 2.04Document No.: FT 000054 Clearance No.: FTDI# 53TTL-232R-3V3-2mm Cable Signal Descriptions7.2Header PinNumberNameTypeColourDescriptionRing Indicator Control Input. When remote wake up1RI#OutputBlueis enabled taking RI# low (20ms active low pulse)can be used to resume the VMUSIC2 or VDRIVE2host controller from suspend
3.5mm Audio Jack 2 core and spiral, 24 AWG diam 5mm TTL-232R-3V3-AJ USB to UART cable with 3.3V TTL level UART signals. 3.5mm Audio Jack 2 core and spiral, 24 AWG diam 5mm TTL-232R-3V3-2mm USB to UART cable with 3.3V TTL level UART signals. 8 way, keyed, 2mm connector for use with FTDI VDRIVE2 or VMUSIC2 modules 7 core, UL2464 26 AWG, diam 5mm
Yaesu FT-100 RS232 23 DB9 Female FT-736R TTL 1 Din 5 or 6 pin 270 Deg FT-757 TTL 16 Supplied with radio. FT-847 RS232 2 DB9 Female FT-980 TTL 20 Din 5 or 6 pin 270 Deg FT-1000 RS232 24 DB25 Female Icom IC-271 TTL 10 IC-275 TTL 12 All these ICOM models use a IC-471 TTL 11 IC-475 TTL 13 3.5 mm Mono Jack Plug. IC-1271 TTL 37 IC-1275 TTL 38 IC-706 .
The USB side of the cable is USB powered and USB 2.0 full speed compatible. Each cable is 1.8m long and supports a data transfer rate up to 3 Mbaud. Each cable supports the FTDIChip-ID , with a unique USB serial number programmed into the FT232R. This feature can be used to create a security or
2.2 Evaluating a module via UART Note - To connect to the Glyn EVB via UART, we suggest using the FTDI TTL-232R-3V3 cable. It can be found on the Glyn Store - FTDI-TTL-232R-3V3 1. A 6-pin header will be required on UART(6). If this is something you need done, please let Glyn know w
In-box 1m cable or Jabra 1.8m cable How to connect using Anker PowerLine/Newnex cable USB-A USB-C 3m USB-A to USB-C cable How to connect using Startech USB 3.0/USB 2.0 Startech USB Extender Power Adapter USB-A USB-A USB-C In-box
APC Back-UPS USB USB APC Back-UPS RS USB USB APC Back-UPS LS USB USB APC Back-UPS ES/CyberFort 350 USB APC Back-UPS BF500 USB APC BACK-UPS XS LCD USB APC Smart-UPS USB USB APC Back-UPS 940-0095A/C cables APC Back-UPS 940-0020B/C cables APC Back-UPS 940-0023A cable APC Back-UPS Office 940-0119A cable APC Ba
receive benefit of S-TTL regardless of manufacture, model or shooting mode. S-TTL offers wide variety for selecting your digital camera. All Digital Camera System (*2) which has available INON AD Mount System or M67 Mount System, is compatible with S-TTL. (*2: except Fuji film F710) S-TTL is compatible with pre-flash type digital camera.
CMOS families in Section 3.8. We’ll use the following definitions of LOW and HIGH in our discussions of TTL circuit behavior: LOW 0–0.8 volts. HIGH 2.0–5.0 volts. TTL.1 Basic TTL NAND Gate The circuit diagram for a 2-input LS-TTL NAND gate, part number 74LS00, is shown in Figure
Tulang Humerus Gambar 2.1 Anatomi 1/3 Tulang Humerus (Syaifuddin, 2011) Sulcus Intertubercularis Caput Humeri Collum Anatomicum Tuberculum Minus Tuberculum Majus Collum Chirurgicum Crista Tubeculi Majoris Crista Tuberculi Majoris Collum Anatomicum Collum Chirurgicum Tuberculum Majus . 4. Otot-otot Penggerak Pada Bahu Menurut Syaifuddin (2011), otot- otot bahu terdiri dari : a. Gerakan fleksi .
