Press Brake Tooling - SM TECH
European Style Press Brake Tooling
Extend The Life Of Your Tools With Nitrex Nitrex high endurance surface enhancement, exclusively from Wilson Tool, increases press brake tooling life by several times that of standard tooling. With a surface hardness of HRC-60 and a consistent 0.51mm of penetration below the surface of the tool, Nitrex adds lubricity to press brake tooling and lowers the coefficient of friction as the material slides over the shoulder of the V-opening on a die. Any Wilson Tool press brake punch or die can be enhanced with Nitrex . Most Wilson Tool press brake dies now come with NITREX as standard at no extra cost. Nitrex High Endurance Surface Enhancement Patent Number: 6,327,884 B1
The Wilson Express Clamping System Express Clamping Systems for: The Wilson Express Clamping System is the most exciting new development in press brake technology to take place in decades. It is a new, highly advanced series of punch holders that include a host of unique and innovative features designed to allow you to set up your press brake fast. Really fast! Loading Punches Is A Snap With the Wilson Express Clamping System, 415mm long punches and individual pieces of sectionalized punches are loaded by simply placing them under the clamps and pushing them upward. There’s no need to slide them in from the end of the machine. The spring loaded clamps capture the punch via the safety groove and hold it in place until the clamps are locked. To lock the clamps, you simply push a single removable lever upward. Amada Z2 Style Press Brakes Unloading Punches Is Fast And Simple To unlock the clamps, you simply pull down the locking lever. Small punch sections may then be removed by pushing inward on the top of the clamps. This opens the clamps, allowing the operator to pull the individual sections straight down. No need to slide them out the end of the machine. And, since the clamps are easily removed by hand, you can remove them from the punch holders that are not in use. Dual Clamping Available For an additional cost you can have the dual clamping feature on your Wilson Express Clamping System. This feature allows you to load punches with the relief area facing forwards or towards the rear of the machine. And, both front and rear clamps are opened and closed simultaneously when the locking lever is actuated. American Press Brakes Uses Standard Tooling Unlike other so-called “quick clamping systems,” the Wilson Express Clamping System is designed to use standard European (Promecam ) style press brake tooling with a safety groove. This allows you to use the same high quality Wilson tooling that you currently own. There is no need for a special type of tooling, and you won’t have to re-purchase the system with every tool that you order. No Hydraulics Required You also won’t need an expensive hydraulic clamping system. The Wilson Express Clamping System is of a mechanical design and does not require hydraulics. This virtually eliminates maintenance and the possibility of hydraulic leaks as well as the possibility of punches being released in the event of a power failure. Amada Z1 and most European (Promecam ) Style Press Brakes Available For Your Press Brake The Wilson Express Clamping System is available for virtually all makes and models of press brakes— with and without adjustment wedges. This makes it easy to take advantage of the productivity gains and improved profitability that come with the Wilson Express Clamping System. Call For A Free Demonstration Organising a free demonstration of this exciting technology is also quick and easy. Simply contact your local Wilson Tool sales engineer or our sales desk on 0800 373748, fax us on 0800 373758 or email us at sales@wilsontool.eu.com to arrange a free demonstration at your premises. Phone: 651-286-6000 Email: pressbrake@wilsontool.com Toll Free Sales Desk: 800-445-4518 Toll Free Fax: 800-539-4590 b Trumpf Press Brakes
Index 2V Dies 2V Die Holders 2V Die Rail And Clamp 2V Dies With Large Shoulder Radii 3V Hemming Die 30 Acute-Angle Punches 60 Acute-Angle Punches 75 Punches 85 Gooseneck Punches 88 Gooseneck Punches 88 & 90 Gooseneck Punches With Thin Tip 88 Narrow Punches 88 Sash Punches 90 Gooseneck Punches 90 Narrow Punches 90 Sash Punches Acute-Angle Large 1V Dies Acute-Angle Quick Change 1V Dies Acute-Angle Quick Change 2V Dies Air Bending Force Chart Metric Bend Limit Graphs Deep Punch Holder Dual Clamping Kits European Die Holders European Punch Holders Express Clamping System Flattening Die Flattening Punches Hemming Dies Large 1V Dies Large 1V Die Holder 44 48 48 45 58 14-15 16 17-18 11 8-9 10 12 13 11 12 14 54 51 42 73 22-39 65 66 71 67-70 4-5 58 21 59 55-57 57 Large Radius Punches Low Profile Quick Change 1V Dies Low Profile Sectionalized 2V Dies Narrow Punch Holders Quick Change 1V Die Holder And Wedge Block Quick Change 1V Dies Quick Change 2V Dies Quick Change 2V Dies With Large Shoulder Radii Quick Change 75 1V Dies Quick Change 75 2V Dies Quick Change Back Gauge Stopper Pads Quick Change Rail Style Flattening Die Quick Reference Chart Rail Style Offset Tools Sectionalized 2V Dies Sectionalized 2V Dies With Large Shoulder Radii Side Gauge Stacking Punch Holder Stacking Rails Standard 88 Punches Standard 90 Punches Standard 88 & 90 Punches With Thin Tip Standard Die Lengths Standard Punch Lengths Tooling Cabinet Urethane Holders Urethane Pads Urethane Rolls 19-20 50 47 64 53 49 40-41 42 52 43 63 58 2-3 62 45-46 47 63 66 48 6 6 7 1 1 72 60 61 72 Prices and specifications subject to change without prior notice. Terms and Conditions: Order: Minimum order is 35.00. Credit: All orders accepted are subject to the approval of our credit department. If you are a new account, please furnish us with a bank reference and three supplier references. A credit limit will be imposed on new accounts until credit has been established. Payment: Cancellation: Returned Material: Claims: Terms are net 30 days. In the event an order is cancelled, a charge will be made to cover labour, material and overheads. A handling charge of 25% is made on all standard parts returned for credit. Written permission and shipping instructions must be obtained before the return of any material. Special tooling cannot be returned. All claims for shortages must be made within 10 days of invoice date.
Standard Punch Lengths FEATURES: 1. Most tools can be easily loaded by a single operator. (S) 2. Easy to store. 415mm 3. All sectionalized tools come pre-cut in nine different pieces. 4. Most sectionalized punches include two ear pieces (horns). 5. NITREX (HRC - 60) is available for every punch in the tooling line. (L) 835mm 6. Special Tooling available. Please contact the sales desk. (X) 835mm SECTION WIDTHS: 100mm LEFT EAR / 100mm RIGHT EAR / 10mm / 15mm / 20mm / 40mm / 50mm / 200mm / 300mm Note: Special lengths are available at additional cost. Standard Die Lengths FEATURES: 1. Most tools can be easily loaded by a single operator. (S) 415mm 2. Easy to store. 3. All sectionalized tools come pre-cut in nine different pieces. 4. Most dies are NITREX enhanced (HRC-60) as standard. (L) 835mm 5. Special Tooling available. Please contact the sales desk. (X) 835mm SECTION WIDTHS: 100mm / 100mm / 10mm / 15mm / 20mm / 40mm / 50mm / 200mm / 300mm Note: Special lengths are available at additional cost. Tel: 44 (0) 1793 831818 Email: sales@wilsontool.eu.com Free Phone: Free Fax: 0800 373748 0800 373758 Tel Free: Fax Free: 1-800 70 90 09 Ireland 1-800 53 55 38 Ireland 1
90 DEGREE BENDING (0.4 - 3.4mm) 100 90200DEGREE BENDING WITH THIN TIP PUNCH STANDARD PUNCHES WITH THIN TIP PAGE 7 QUICK CHANGE 2V DIES PAGE 40-41 NARROW PUNCHES PAGE 12 NARROW PUNCHES PAGE QUICK CHANGE 2V DIES QUICK CHANGE 2V DIES PAGE 40-41 PAGE QUICK CHANGE 2V DIES PAGE 2V DIE RAIL PAGE 48 QUICK CHANGE 2V DIES QUICK CHANGE 2V DIES PAGE PAGE 40-41 2VDIEDIE RAIL RAIL PAGE 48 PAGE DIE RAIL PAGE 2V DIE RAIL PAGE 48 DIE RAIL PAGE 2V DIE HOLDERS 2V DIE HOLDERS PAGE PAGE 48 2V DIE HOLDERS 2V DIE HOLDERS PAGE PAGE 48 400 500 STANDARD PUNCHES WITH THIN TIP PAGE STANDARD PUNCHES PAGE 6 STANDARD PUNCHES PAGE 90 DEGREE BENDING WITH THIN TIP GOOSENECK PUNCH 90 DEGREE BENDING WITH NARROW PUNCH 90 DEGREE BENDING WITH GOOSENECK PUNCH 300 2V HOLDERS 2V DIEDIE HOLDERS PAGE PAGE 48 90 DEGREE BENDING 600 (SASH) GOOSENECK PUNCHES PAGE 8-11 GOOSENECK PUNCHES GOOSENECK PUNCHES WITH THINTHIN TIP WITH TIP PAGE PAGE 10 DEEP GOOSENECK PUNCHES PAGE SASH PUNCHES PAGE 13-14 SASH PUNCHES PAGE QUICK CHANGE NARROW 1V DIES 1V DIES PAGE PAGE 49 QUICK CHANGE 2V DIES PAGE 40-41 QUICK CHANGE 2V DIES PAGE 2V DIES PAGE 44 2V DIES PAGE 2V DIE RAIL DIE RAIL PAGE PAGE 48 QUICK CHANGE 1V NARROW 1V DIE HOLDERS DIE HOLDERS PAGE PAGE 53 2V DIE HOLDERS 2V DIE HOLDERS PAGE PAGE 48 2V 2VDIE HOLDERS DIE HOLDERS PAGE PAGE 48 1300 LARGE RADIUS BENDING (WITH URETHANE DIE) 1500 LARGE RADIUS PUNCHES LARGE RADIUS PUNCHES PAGE PAGE 19-20 90 DEGREE BENDING (9.5 - 12.7mm) LARGE RADIUS PUNCHES LARGE RADIUS PUNCHES PAGE 19-20 PAGE LARGE RADIUS BENDING 1200 LARGE RADIUS PUNCHES PAGE 19-20 LARGE RADIUS PUNCHES PAGE URETHANE PADS PAGE 61 URETHANE PADS PAGE LARGE 1V DIES PAGE 55-57 LARGE 1V DIES PAGE URETHANE HOLDERS URETHANE HOLDERS PAGE PAGE 60 LARGE 1V DIES LARGE 1V DIES PAGE PAGE 55-57 2
ACUTE-ANGLE BENDING (2.7 - 4.9mm) 1400 90 DEGREE BENDING 900 (3.8 - 9.5mm) ACUTE ANGLE PUNCHES ACUTE ANGLE PUNCHES PAGE PAGE 14-16 HEMMING (2 STAGE) (0.4 - 1.9mm) 800 ACUTE ACUTE ANGLE ANGLE PUNCHES PAGE PUNCHES PAGE 14-16 ACUTE ANGLE ACUTE ANGLE PUNCHES PUNCHES PAGE PAGE 14-16 STEP STEP1 1 ACUTE ANGLE ACUTE ANGLE LARGE LARGE 1V DIES 1V DIES PAGE PAGE 54 HEMMING DIES HEMMING DIES PAGE PAGE 59 LARGE LARGE 1V DIES 1V DIES PAGE PAGE 55-57 STEPSTEP2 2 ACUTE-ANGLE BENDING (0.4 - 1.9mm) DEEP BOX BENDING 1900 DEEP PUNCH HOLDER 700 1600 DEEP HOLDER DEEP PUNCHPUNCH HOLDER PAGE PAGE 65 STANDARD PUNCH HOLDER (SUPPLIED WITH MACHINE) STANDARD PUNCH HOLDER (SUPPLIED WITH MACHINE) OR NARROW PUNCH HOLDERS OR NARROW PUNCH HOLDERS PAGE PAGE 64 ACUTE ANGLE PUNCHES ACUTE ANGLE PUNCHES PAGE PAGE 14-16 STACKING PUNCH HOLDER STACKING PUNCH HOLDER PAGE AND NARROW OR 66 NARROW PUNCH HOLDERS PAGE PUNCH HOLDERS PAGE 64 ACUTE ANGLE QUICK ACUTE ANGLE QUICK CHANGE 2V DIE CHANGE 2V DIES PAGE PAGE 42 STANDARD PUNCHES PAGE 6 STANDARD PUNCHES PAGE 2V DIE RAIL PAGE 48 LOW PROFILE QUICK CHANGE LOW PROFILE NARROW 1V DIES 1V DIES PAGE 50 PAGE 2V DIE RAILS PAGE 1000 STANDARD PUNCHES STANDARD PUNCHES PAGE PAGE 6 NARROW 1V DIE HOLDERS QUICK CHANGE 1V PAGE DIE HOLDERS PAGE 53 2V DIE HOLDERS PAGE 48 2V DIE HOLDERS PAGE HEMMING (0.4 - 1.5mm) HEMMING (0.4 - 3.0mm) OFFSET BENDING (0.4 - 1.5mm) 1800 1100 FLATTENING FLATTENING PUNCHES PUNCHES PAGE PAGE 21 FLATTENING PUNCHES PAGE 21 FLATTENING PUNCHES PAGE RAIL STYLE OFFSET TOOLS OFFSET TOOLS PAGE PAGE 62 FLATTENING DIES PAGE 58 FLATTENING DIES PAGE 3V HEMMING DIES 3V HEMMING DIES PAGE PAGE 58 2V DIE RAIL PAGE 48 DIE RAIL PAGE 2V DIE HOLDERS 2V DIE HOLDERS PAGE PAGE 48 3
Wilson Express Clamping System 43815 (replaces 43015) For Conventional Press Brakes With Wedge 43817 (replaces 43017) Z1 Series With Wedge 43031 For Mitsubishi Toyokoki HYB Series Press Brakes 43033 For Mitsubishi Toyokoki APB Series Press Brakes -Dual Clamping Included -Dual Clamping Included *Note: Other Punch Holders Shown On Pages 64–70 Tel: 44 (0) 1793 831818 Email: sales@wilsontool.eu.com 4 Free Phone: Free Fax: 0800 373748 0800 373758 Tel Free: Fax Free: 1-800 70 90 09 Ireland 1-800 53 55 38 Ireland
Wilson Express Clamping System 43818 (replaces 43018) Z2 Series With Wedge 43819 (replaces 43019) For Trumpf Press Brakes With Wedge *Note: Other Punch Holders Shown On Pages 64–70 Express Clamp Torque Wrench Kit Cat. No. 08002, 08003, 43726, 06793, 06795, CATALOGUE COMPONENT PIECE PRICE NUMBER 08002 Complete Kit 08003 Case 43726 Pivots 06793 Wrench 06795 Hex Tips Tel: 44 (0) 1793 831818 Email: sales@wilsontool.eu.com Free Phone: Free Fax: 0800 373748 0800 373758 Tel Free: Fax Free: 1-800 70 90 09 Ireland 1-800 53 55 38 Ireland 5 KIT PRICE 1/Kit 2/Kits 1/Kit 2/Kits
Standard 88 Punches Cat. No. E40002, E40006, E40008, E40015, E40023, 4E0030 Part No. E40002 30mm 35mm R 5mm "H" 35mm R Pirce) (Ear(EarPiece) 9mm 10mm 88 CATALOGUE NUMBER E40002 E40006 E40008 E40015 E40023 E40030 0 R mm 0.2 0.6 0.8 1.5 2.3 3.0 MAX. TON per metre (L & S) 100 100 100 100 100 100 MAX. TON per metre (X) 47 47 47 47 47 47 X SECTIONALIZED S 415mm L 835mm “H” 66.9 66.4 66.6 66.3 66.0 65.7 *Note: Punch tip modifications and punch relief available at additional cost. Contact the sales desk for prices and lead times. Nitrex (HRC-60) available for every punch in the tooling range at additional cost. Standard 90 Punches Cat. No. E40102, E40108, E40115, E40123, E40130 Part No. E40102 30mm 35mm R 5mm "H" 35mm R 9mm (Ear Piece) (Ear Piece) 10mm 0 90 CATALOGUE NUMBER E40102 E40108 E40115 E40123 E40130 R mm 0.2 0.8 1.5 2.3 3.0 MAX. TON per metre (L & S) 100 100 100 100 100 MAX. TON per metre (X) 47 47 47 47 47 “H” 66.9 66.7 66.4 66.0 65.7 L 835mm S 415mm X SECTIONALIZED *Note: Punch tip modifications and punch relief available at an additional cost. Contact the application sales desk for pricing and lead times. Nitrex (HRC-60) available for every punch and die in the tooling line. Tel: 44 (0) 1793 831818 Email: sales@wilsontool.eu.com 6 Free Phone: Free Fax: 0800 373748 0800 373758 Tel Free: Fax Free: 1-800 70 90 09 Ireland 1-800 53 55 38 Ireland
Standard 90 Punches With Thin Tip Cat. No. E40202 and E40206 Part No. E40202 30mm 10mm "H" R 5mm R 4mm (Ear Piece) (Ear Piece) 5mm 10mm 0 90 CATALOGUE NUMBER E40202 E40206 MAX. TON per metre (L & S) 20 20 R mm 0.2 0.6 MAX. TON per metre (X) 10 10 L 835mm “H” 66.9 66.4 S 415mm X SECTIONALIZED *Note: Punch tip modifications and punch relief available at additional cost. Contact the sales desk for prices and lead times. Nitrex (HRC-60) available for every punch in the tooling range at additional cost. Standard 88 Punches With Thin Tip Cat. No. E40212 Part No. E40212 30mm 10mm "H" R 5mm R 5mm 4.02mm (Ear Piece) (Ear Piece) 10mm 0 88 CATALOGUE NUMBER E40212 R mm 0.2 MAX. TON per metre (L & S) 20 MAX. TON per metre (X) 10 “H” 66.9 L 835mm S 415mm X SECTIONALIZED *Note: Punch tip modifications and punch relief available at an additional cost. Contact the application sales desk for pricing and lead times. Nitrex (HRC-60) available for every punch and die in the tooling line. Tel: 44 (0) 1793 831818 Email: sales@wilsontool.eu.com Free Phone: Free Fax: 0800 373748 0800 373758 Tel Free: Fax Free: 1-800 70 90 09 Ireland 1-800 53 55 38 Ireland 7
88 Gooseneck Punches Cat. No. E40302 - E40630 Part No. E40302 30mm "H" 35mm R 5mm 35mm 10mm 9mm R (EarPiece) Piece) (Ear 88 0 Part No. E40402 30mm 35mm "H" R 5mm 35mm R (Ear Piece) (Ear Piece) 9mm 10mm 0 88 *Note: Punch tip modifications and punch relief available at additional cost. Contact the sales desk for prices and lead times. Nitrex (HRC-60) available for every punch in the tooling range at additional cost. Tel: 44 (0) 1793 831818 Email: sales@wilsontool.eu.com 8 Free Phone: Free Fax: 0800 373748 0800 373758 Tel Free: Fax Free: 1-800 70 90 09 Ireland 1-800 53 55 38 Ireland
88 Gooseneck Punches Cat. No. E40302 - E40630 Part No. E40602 30mm 35mm "H" R 5mm 35mm R (Ear Piece) 9mm 10mm 88 CATALOGUE NUMBER E40302 E40306 E40308 E40402 E40406 E40408 E40415 E40430 E40602 E40606 E40608 E40615 E40630 R mm 0.2 0.6 0.8 0.2 0.6 0.8 1.5 3.0 0.2 0.6 0.8 1.5 3.0 MAX. TON per metre (L & S) MAX. TON per metre (X) 50 50 50 50 50 50 50 50 70 70 70 70 70 50 50 50 47 47 47 47 47 47 47 47 47 47 “H” 119.9 119.4 119.7 104.9 104.4 104.6 104.3 103.7 89.9 89.4 89.6 89.3 88.7 L 835mm S 415mm X SECTIONALIZED *Note: Punch tip modifications and punch relief available at additional cost. Contact the sales desk for prices and lead times. Nitrex (HRC-60) available for every punch in the tooling range at additional cost. Tel: 44 (0) 1793 831818 Email: sales@wilsontool.eu.com Free Phone: Free Fax: 0800 373748 0800 373758 Tel Free: Fax Free: 1-800 70 90 09 Ireland 1-800 53 55 38 Ireland 9
88 Gooseneck Punches With Thin Tip Cat. No. E40702, E40706, E40708 Part No. E40702 30mm 30mm "H" R 10mm 25mm R (Ear Piece) 6mm 10mm 88 CATALOGUE NUMBER E40702 E40706 E40708 MAX. TON per metre (L & S) 50 50 50 R mm 0.2 0.6 0.8 MAX. TON per metre (X) 30 30 30 S 415mm L 835mm “H” 89.9 89.4 89.6 X SECTIONALIZED *Note: Punch tip modifications and punch relief available at additional cost. Contact the sales desk for prices and lead times. Nitrex (HRC-60) available for every punch in the tooling range at additional cost. 90 Gooseneck Punches With Thin Tip Cat. No. E40712 and E40718 Part No. E40712 30mm 30mm "H" R 10mm 25mm R (Ear Pirce) (Ear Piece) 6mm 90 CATALOGUE NUMBER E40712 E40718 R mm 0.2 0.8 10mm 0 MAX. TON per metre (L & S) 50 50 MAX. TON per metre (X) 30 30 “H” 89.9 89.7 L 835mm S 415mm X SECTIONALIZED *Note: Punch tip modifications and punch relief available at additional cost. Contact the sales desk for prices and lead times. Nitrex (HRC-60) available for every punch in the tooling range at additional cost. Tel: 44 (0) 1793 831818 Email: sales@wilsontool.eu.com 10 Free Phone: Free Fax: 0800 373748 0800 373758 Tel Free: Fax Free: 1-800 70 90 09 Ireland 1-800 53 55 38 Ireland
90 Gooseneck Punches Cat. No. E40502 Part No. E40502 30mm 35mm "H" R 5mm 35mm R (Ear Piece) 9mm 10mm 90 CATALOGUE NUMBER E40502 MAX. TON per metre (L & S) R mm 0.2 50 MAX. TON per metre (X) 47 L 835mm “H” S 415mm X SECTIONALIZED 104.9 *Note: Punch tip modifications and punch relief available at additional cost. Contact the sales desk for prices and lead times. Nitrex (HRC-60) available for every punch in the tooling range at additional cost. 85 Gooseneck Punches Cat. No. E44540 and E44560 30mm Part No. E40402 35mm "H" R 5mm 35mm 15mm R 10mm (Ear EAR Piece) PIECE 85 CATALOGUE NUMBER E44540 E44560 R mm 4.8 6.4 MAX. TON per metre (L & S) 100 100 MAX. TON per metre (X) “H” 47 47 105.0 104.3 L 835mm S 415mm X SECTIONALIZED *Note: Punch tip modifications and punch relief available at additional cost. Contact the sales desk for prices and lead times. Nitrex (HRC-60) available for every punch in the tooling range at additional cost. Tel: 44 (0) 1793 831818 Email: sales@wilsontool.eu.com Free Phone: Free Fax: 0800 373748 0800 373758 Tel Free: Fax Free: 1-800 70 90 09 Ireland 1-800 53 55 38 Ireland 11
88 Narrow Punches Cat. No. E40802 and E40806 Part No. E40802 30mm "H" 70mm 6mm R 88 CATALOGUE NUMBER E40802 E40806 MAX. TON per metre (L & S) 50 50 R mm 0.2 0.6 MAX. TON per metre (X) 50 50 S 415mm L 835mm “H” 95.0 94.5 X SECTIONALIZED *Note: Sectionalized version does not include ear pieces (horns). Ear pieces (horns) available at additional cost. Punch tip modifications and punch relief available at additional cost. Contact the sales desk for pricing and lead times. Nitrex (HRC-60) available for every punch in the tooling range at additional cost. 90 Narrow Punches Cat. No. E40902 Part No. E40902 30mm "H" 70mm 6mm R 90 CATALOGUE NUMBER E40902 R mm 0.2 MAX. TON per metre 50 S 415mm L 835mm “H” 95.0 X SECTIONALIZED *Note: Sectionalized version does not include ear pieces (horns). Ear pieces (horns) available at additional cost. Punch tip modifications and punch relief available at additional cost. Contact the sales desk for pricing and lead times. Nitrex (HRC-60) available for every punch in the tooling range at additional cost. Tel: 44 (0) 1793 831818 Email: sales@wilsontool.eu.com 12 Free Phone: Free Fax: 0800 373748 0800 373758 Tel Free: Fax Free: 1-800 70 90 09 Ireland 1-800 53 55 38 Ireland
88 Sash Punches Cat. No. E41002, E41006, E41102, E41106 Part No. E41002 30mm 25mm "H" R 10mm 10mm R (Ear Piece) 8mm 20mm 10mm 88 Part No. E41102 30mm 25mm "H" R 10mm 10mm R 8mm 10mm CATALOGUE NUMBER R mm E41002 E41006 E41102 E41106 0.2 0.6 0.2 0.6 MAX. TON per metre (L & S) 30 30 30 30 20mm (Ear Piece) 88 MAX. TON per metre (X) 30 30 30 30 “H” 99.9 99.4 69.9 69.4 L 835mm S 415mm X SECTIONALIZED *Note: Punch tip modifications and punch relief available at additional cost. Contact the sales desk for prices and lead times. Nitrex (HRC-60) available for every punch in the tooling range at additional cost. Tel: 44 (0) 1793 831818 Email: sales@wilsontool.eu.com Free Phone: Free Fax: 0800 373748 0800 373758 Tel Free: Fax Free: 1-800 70 90 09 Ireland 1-800 53 55 38 Ireland 13
90 Sash Punches Cat. No. E41202 Part No. E40902 30mm 25mm "H" R 10mm 10mm (Ear Piece) R 8mm 10mm 90 CATALOGUE NUMBER E41202 R mm 0.2 MAX. TON per metre (L & S) MAX. TON per metre (X) “H” 30 30 69.9 20mm L 835mm S 415mm X SECTIONALIZED *Note: Punch tip modifications and punch relief available at additional cost. Contact the sales desk for prices and lead times. Nitrex (HRC-60) available for every punch in the tooling range at additional cost. 30 Acute-Angle Punches Cat. No. E41908 Part No. E41908 30mm "H" 20mm R 8mm 20mm R 30 CATALOGUE NUMBER E41908 R mm 0.8 (Ear Piece) (Ear Piece) 12mm 18mm 0 MAX. TON per metre (L & S) MAX. TON per metre (X) “H” 100 20 104.0 L 835mm S 415mm X SECTIONALIZED *Note: Punch tip modifications and punch relief available at additional cost. Contact the sales desk for prices and lead times. Nitrex (HRC-60) available for every punch in the tooling range at additional cost. Tel: 44 (0) 1793 831818 Email: sales@wilsontool.eu.com 14 Free Phone: Free Fax: 0800 373748 0800 373758 Tel Free: Fax Free: 1-800 70 90 09 Ireland 1-800 53 55 38 Ireland
30 Acute-Angle Punches Cat. No. E41315 and E41330 30mm "H" R 30 CATALOGUE NUMBER E41315 E41330 R mm 1.5 3.0 MAX. TON per metre (L & S) 100 100 MAX. TON per metre (X) 100 100 L 835mm “H” 102.0 97.7 S 415mm X SECTIONALIZED *Note: Sectionalized version does not include ear pieces (horns). Ear pieces (horns) available at additional cost. Punch tip modifications and punch relief available at additional cost. Contact the sales desk for prices and lead times. Nitrex (HRC-60) available for every punch in the tooling range at additional cost. 30 Acute-Angle Punches Cat. No. E42610 30mm "H" 18.24mm R 300 CATALOGUE NUMBER E42610 R mm 0.8 MAX. TON per metre (L & S) MAX. TON per metre (X) “H” 100 100 65.5 L 835mm S 415mm X SECTIONALIZED *Note: Sectionalized version does not include ear pieces (horns). Ear pieces (horns) available at additional cost. Punch tip modifications and punch relief available at additional cost. Contact the sales desk for prices and lead times. Nitrex (HRC-60) available for every punch in the tooling range at additional cost. Tel: 44 (0) 1793 831818 Email: sales@wilsontool.eu.com Free Phone: Free Fax: 0800 373748 0800 373758 Tel Free: Fax Free: 1-800 70 90 09 Ireland 1-800 53 55 38 Ireland 15
60 Acute-Angle Punches Cat. No. E41440 and E41460 Part No. E41440 30mm "H" R 60 CATALOGUE NUMBER R mm MAX. TON per metre (L & S) “H” E41440 E41460 4.8 6.0 100 100 66.2 65.0 L 835mm S 415mm X SECTIONALIZED *Note: Sectionalized version does not include ear pieces (horns). Ear pieces (horns) available at additional cost. Punch tip modifications and punch relief available at additional cost. Contact the sales desk for prices and lead times. Nitrex (HRC-60) available for every punch in the tooling range at additional cost. Tel: 44 (0) 1793 831818 Email: sales@wilsontool.eu.com 16 Free Phone: Free Fax: 0800 373748 0800 373758 Tel Free: Fax Free: 1-800 70 90 09 Ireland 1-800 53 55 38 Ireland
75 Punches Cat. No. E44000 - E44030 Part No. E44000 30mm 35mm R 5mm "H" 35mm (Ear Piece) R 10mm 9.6mm 75 Part No. E44030 30mm 35mm "H" R 5mm 35mm (Ear Piece) R 10mm 10mm 75 CATALOGUE NUMBER E44000 E44001 E44003 E44030 E44031 E44033 R mm 0.8 1.5 3.0 0.8 1.5 3.0 MAX. TON per metre (L & S) 100 100 100 50 50 50 MAX. TON per metre (X) 47 47 47 50 50 50 “H” 67.6 67.2 66.2 120.0 119.5 118.6 L 835mm S 415mm X SECTIONALIZED *Note: Punch tip modifications and punch relief available at additional cost. Contact the sales desk for prices and lead times. Nitrex (HRC-60) available for every punch in the tooling range at additional cost. Tel: 44 (0) 1793 831818 Email: sales@wilsontool.eu.com Free Phone: Free Fax: 0800 373748 0800 373758 Tel Free: Fax Free: 1-800 70 90 09 Ireland 1-800 53 55 38 Ireland 17
75 Punches Cat. No. E44020 - E44040 Part No. E44020 30mm 35mm R 5mm "H" 35mm (Ear Piece) 10mm R 10mm 30mm 75 Part No. E44040 Part No. E44010 * Nitrex is standard on Cat. No. 44040 only 30mm "H" "H" R 10mm 4.8mm R 75 75 CATALOGUE NUMBER E44020 E44021 E44023 E44010 E44011 E44013 *E44040 R mm 0.8 1.5 3.0 0.8 1.5 3.0 0.8 MAX. TON per metre (L & S) 70 70 70 50 50 50 50 MAX. TON per metre (X) 47 47 47 50 50 50 47 “H” 90.0 89.5 88.6 95.0 94.5 93.6 160.0 L 835mm S 415mm X SECTIONALIZED Call for pricing and lead time. *Note: Sectionalized version does not include ear pieces (horns). Ear pieces (horns) available at additional cost. (E44010 only) Punch tip modifications and punch relief available at additional cost. Contact the sales desk for prices and lead times. Nitrex (HRC-60) available for every punch in the tooling range at additional cost. Tel: 44 (0) 1793 831818 Email: sales@wilsontool.eu.com 18 Free Phone: Free Fax: 0800 373748 0800 373758 Tel Free: Fax Free: 1-800 70 90 09 Ireland 1-800 53 55 38 Ireland
Large Radius Punches Cat. No. E41709 - E41719 Part No. E41709 Part No. E41712 30mm 30mm "H" "H" R 9.5 mm R 12.7 mm Part No. E41715 Part No. E41719 30mm 30mm "H" "H" 15.9mm CATALOGUE MAX. TON NUMBER per metre E41709 100 E41712 100 E41715 100 E41719 100 R 19mm “H” 83.0 89.0 87.0 91.0 L 835mm S 415mm X SECTIONALIZED *Note: Sectionalized version does not include ear pieces (horns). Ear pieces (horns) available at additional cost. Nitrex (HRC-60) available for every punch in the tooling range at additional cost. Additional radii available, please contact the sales desk. Tel: 44 (0) 1793 831818 Email: sales@wilsontool.eu.com Free Phone: Free Fax: 0800 373748 0800 373758 Tel Free: Fax Free: 1-800 70 90 09 Ireland 1-800 53 55 38 Ireland 19
Large Radius Punches Cat. No. E41722 and E41725 Part No. E41722 Part No. E41725 30mm 30mm "H" "H" R 22.2mm R 25.4mm CATALOGUE MAX. TON NUMBER per metre E41722 100 E41725 100 “H” 94.0 96.0 L 835mm S 415mm X SECTIONALIZED *Note: Sectionalized version does not include ear pieces (horns). Ear pieces (horns) available at an additional cost. Nitrex (HRC-60) available for every punch and die in the tooling line. Additional radii available, please contact our application sales desk. Tel: 44 (0) 1793 831818 Email: sales@wilsontool.eu.com 20 Free Phone: Free Fax: 0800 373748 0800 373758 Tel Free: Fax Free: 1-800 70 90 09 Ireland 1-800 53 55 38 Ireland
Flattening Punches Cat. No. E41523 and E41630 40mm Part No. E41523 30mm "H" 23mm Part No. E41630 30mm 14mm "H" 30mm 12mm CATALOGUE MAX. TON NUMBER per metre E41523 E41630 100 100 L 835mm “H” S 415mm 65.0 84.0 *Note: Nitrex (HRC-60) available for every punch in the tooling range at additional cost. Tel: 44 (0) 1793 831818 Email: sales@wilsontool.eu.com Free Phone: Free Fax: 0800 373748 0800 373758 Tel Free: Fax Free: 1-800 70 90 09 Ireland 1-800 53 55 38 Ireland 21
Bend Limit Graph 220 CATALOGUE NO. E40002, E40008, E40015, E40023, E40030, E40102, E40108, E40115, E40123, E40130 210 200 190 L 180 Z2 STYLE (SOLID LINES) 170 160 150 Z1 STYLE (DASHED LINES) 140 130 120 110 100 90 80 70 W 60 50 40 30 L 20 10 W 10 20 30 40 50 60 70 80 90 Tel: 44 (0) 1793 831818 Email: sales@wilsontool.eu.com 22 100 Free Phone: Free Fax: 110 120 130 0800 373748 0800 373758 140 Tel Free: Fax Free: 150 160 170 180 1-800 70 90 09 Ireland 1-800 53 55 38 Ireland
Bend Limit Graph 220 CATALOGUE NO. E40202, E40212 210 200 190 L Z2 STYLE (SOLID LINES) 180 170 160 Z1 STYLE (DASHED LINES) 150 140 130 120 110 100 90 80 70 W 60 50 40 30 L 20 10 W 10 20 Tel: 44 (0) 1793 831818 Email: sales@wilsontool.eu.com 30 40 Free Phone: Free Fax: 50 60 0800 373748 0800 373758 70 80 90 Tel Free: Fax Free: 100 110 1-800 70 90 09 Ireland 1-800 53 55 38 Ireland 23 120 130 140 150 160 170 180
Bend Limit Graph 220 CATALOGUE NO. E40302, E40308 210 200 190 Z2 STYLE (SOLID LINES) L Z1 STYLE (DASHED LINES) 180 170 160 150 140 130 120 110 100 90 80 70 W 60 50 40 30 L 20 10 W 10 20 30 40 50 60 70 80 90 Tel: 44 (0) 1793 831818 Email: sales@wilsontool.eu.com 24 100 Free Phone: Free Fax: 110 120 130 0800 373748 0800 373758 140 Tel Free: Fax Free: 150 160 170 180 1-800 70 90 09 Ireland 1-800 53 55 38 Ireland
Bend Limit Graph 220 CATALOGUE NO. E40402, E40408, E40415, E40430, E40502 210 200 190 Z2 STYLE (SOLID LINES) L 180 Z1 STYLE (DASHED LINES) 170 160 150 140 130 120 110 100 90 80 70 W 60 50 40 30 L 20 10 W 10 20 Tel: 44 (0) 1793 831818 Email: sales@wilsontool.eu.com 30 40 Free Phone: Free Fax: 50 60 0800 373748 0800 373758 70 80 90 Tel Free: Fax Free: 100 110 1-800 70 90 09 Ireland 1-800 53 55 38 Ireland 25 120 130 140 150 160 170 180
Bend Limit Graph 220 CATALOGUE NO. E40602, E40608, E40615, E40630 210 200 190 (SOLID LINES) 180 170 7 70 CATALOGUE (DASHED LINES) 160 150 140 130 120 110 100 90 80 7 70 60 50 4 40 30 L 20 10 10 20 30 40 50 60 70 80 90 Tel: 44 (0) 1793 831818 Email: sales@wilsontool.eu.com 26 100 Free Phone: Free Fax: 110 120 130 0800 373748 0800 373758 140 Tel Free: Fax Free: 150 160 170 7 70 180 1-800 70 90 09 Ireland 1-800 53 55 38 Ireland
Bend Limit Graph 220 CATALOGUE NO. E40702, E40708, E40712, E40718 210 200 190 CAT (SOLID LINES) 180 170 7 70 CAT (DASHED LINES) 160 150 140 130 120 110 100 90 80 7 70 60 5 4 40 30 L 2 10 10 20 Tel: 44 (0) 1793 831818 Email: sales@wilsontool.eu.com 30 40 Free Phone: Free Fax: 50 60 0800 373748 0800 373758 70 80 90 Tel Free: Fax Free: 100 110 120 1-800 70 90 09 Ireland 1-800 53 55 38 Ireland 27 130 140 150 160 170 7 70 180
Bend Limit Graph 220 CATALOGUE NO. E44540, E44560 210 200 190 Z2 STYLE (SOLID LINES) L 180 Z1 STYLE (DASH
a consistent 0.51mm of penetration below the surface of the tool, Nitrex adds lubricity to press brake tooling and lowers the coefficient of friction as the material slides over the shoulder of the V-opening on a die. Any Wilson Tool press brake punch or die can be enhanced with Nitrex . . Amada Z2 Style Press Brakes American Press Brakes
C. Modeling ANSYS workbench The finite element method is analyzed on ANSYS Workbench 17.2. The project schematic on workbench. The geometrical model of Al-MMC brake disc- Kevlar brake pad, Al-MMC brake disc-aluminum alloy brake pad and Al-MMC brake disc-ceramic brake pad were simulated by ANSYS
catalog gb www.wila.nl 2021 order our tooling online! www.wila.nl sales: 31 (0)573 28 98 50 we live press brake productivity 3 . wila press brake tooling systems 4 wila's values 5 tool holders 8 fact sheet 9-11 new standard premium 12 new standard pro 18 american style 32
Hufford A-12 14" x 24 ft. Extrusion 60 Ton Parsons Watson-Stillman Hot Joggling and Hydro Press 575 Ton . Cincinnati Press Brake 42 ft. Wide 1250 Ton Cincinnati Press Brake 26 ft. Wide 600 Ton Lodge & Shipley Press Brake 10 ft. Wide 150 Ton Chicago Press Brake 10 ft. Wide 100 Ton Di-Arco Press Brake 8 ft. Wide 100 Ton Lodge & Shipley Shear .
S Cam full air brake system with air dryer, nylon brake pipes and load conscious relief valve in rear brake circuit makes driving more safe. Service brakes are supplemented by engine exhaust brake, coupled with service brake operation. This enhances life of brake linings, brake drums & tyres. Provision for ABS brakes. An exhaust brake isolator .
on disc brakes The problem: Brake pad fails to disengage and rubs against the disc. This can cause the brake system to overheat. Causes: Brake pad seized Brake piston stuck in calliper Driving with depressed brake pedal, e.g. when going downhill Possible consequences: Reduced brake
Fig. 3. Controller layout for the decoupledelectro-hydraulic brake system. Legend: ABSact - ABS activation key, Fbrkped - Brake pedal force applied by driver, fcorr - Correction factor, mest - Estimated vehicle mass, pest,ij - Estimated brake pressure, sped - Brake pedal travel, Tbrake - Brake torque delivered from brake system, Tdistr,ij - Distributed brake torque demand, Tdem .
Tecnostamp Press Brake Tooling Tecnostamp are one of Europe's largest independent manufacturers of press brake tooling. Tecnostamp produce more than 900 profiles to suit nearly every press brakes machine including: ѻ Amada ѻ Promecam ѻ Edwards/Beyeler ѻ Bystronic ѻ Trumpf ѻ LVD ѻ EHT ѻ SafanDarley ѻ Baykal ѻ Durma ѻ Ursviken
Annual Men’s Day Sunday, October 26, 2008 Order of Service Devotion Men’s Day Praise Team Responsive Reading Psalm 1 Congregational Singing This Little Light of Mine Selection Men’s Day Choir Altar Prayer Dance Selection Creations of God Announcements Bro. Robert Shields Pastoral Observations Message Rev. Jeffery A. Lang, Senior Pastor Southside Church & International Ministries Jackson .
