1/8 Solenoid Operated Directional Valves, DSG-01 Series
1/8 Solenoid Operated Directional Valves, DSG-01 SeriesThese are Solenoid Operated Directional Valves of high pressure, highflow and low pressure drop, the features of which can be materializedby employing a powerful wet type solenoid and the rational flowchannel design. High Pressure & High Flow RateIn comparison to our existing lines, both the pressure and flow ofthese valves are much increased. Max. Operating Pressure: approx. 10 % increased [31.5 35 MPa(4570 5080 PSI)]Terminal Box Type Max. T-Line Back Pressure: approx. 30 % increased [16 21 MPa(2320 3050 PSI)] Max. Flow Rate: approx. 60 % increased [63 100 L/min (16.64 26.42 U.S.GPM)] Low Pressure DropThe pressure drop of these valves is reduced by 10 % from 1.0 to 0.9MPa (145 to 131 PSI), in comparison to our existing lines*; the valveseffectively reduce the energy consumption of the unit.{* At Flow Rate: 60 L/min (15.9 U.S.GPM), Spool Type: 3C2 (P A)} Compact & Small MassDespite of high pressure, high flow and low pressure drop, these valvePlug-in Connector Typebodies are compact and lightweight with DC double solenoids; theoverall length and mass are reduced from 210 to 205 mm (8.26 to 8.07inch) and from 2.2 to 1.85 kg (4.85 to 4.08 lbs), respectively. Shockless type availableIn addition to the standard valves for high pressure and high flow, ashockless type capable of minimizing noise and vibration in pipingduring spool changeover is also available. Stable OperationDue to the powerful magnetic and spring force of the solenoids, thesevalves exhibit a high tolerance to contaminants and especially stableoperation. IP65-equivalent high dust- and water-proofThese valves demonstrate excellent dust- and water-proofcharacteristics, in compliance with I. E. C. Pub. 529. IP65 and JIS C0920 IP65 (dust- and jet-proof type). Usable in products of various standardsThese standard valves are CE certified for installation in equipment overseas.UL/CSA certified products are also available. SpecificationsValve TypeModel NumbersMax. Flow 2L/min(U.S.GPM)Max. OperatingPressureMPa (PSI)Max. T-LineBack PressureMPa (PSI)100(26.4)35(5080)21(3050)DSG-01-3C - -70/7090Standard TypeDSG-01-2D2- -70/7090DSG-01-2B - -70/7090Shockless TypeS-DSG-01-3C - -70/7090S-DSG-01-2B2- -70/7090Max. ChangeoverFrequencyCycle/min {min–1}Masskg(lbs.)300R Type Sol. 6)16(2320)16(2320)300R Type Sol. Only1201.4(3.09)1.85(4.08)1.4(3.09)L-DSG-01-3C - -70/7090Low Wattage(14W)Type 1L-DSG-01-2D2- -70/7090L-DSG-01-2N - -70/7090L-DSG-01-2B- -70/70901.85(4.08)1.4(3.09) 1. For details of L-DSG-01, please contact us. 2. Maximum flow indicates a ceiling flow depends on the type of spool and operating condition, refer to the List of Spool Functions on pages 347to 351 for details.344DSG-01 Series Solenoid Operated Directional Valves
DIRECTIONAL CONTROLSSub-platePipingSizeJapanese Standard "JIS "Sub-plat eModel NumbersThreadSizeEuropean Design StandardSub-plat eModel NumbersThreadSizeN.American Design StandardSub-plat eModel NumbersApprox.Masskg (lbs.)ThreadSize1/8DSGM-01-31Rc 1/8DSGM-01-31801/8 BSP. FDSGM-01-31901/8 NPT0.8 (1.8 )1/4DSGM-01X-31Rc 1/4DSGM-01X-31801/4 BSP. FDSGM-01X-31901/4 NPT0.8 (1.8 )3/8DSGM-01Y-31Rc 3/8DSGM-01Y-31903/8 NPT0.8 (1.8 )Sub-plates are available. Specify the sub-plate model number from the table above.When sub-plates are not used, the mounting surface should have a good machined finish.Mounting BoltFor socket head cap screws in the table below are included.Soc. Hd. Cap Screw (4 pcs.)Japanese Standard "JIS"European Design StandardM5 45 Lg.N. American Design StandardNo. 10-24 UNC 1-3/4 Lg .Tightening Torque5 - 7 Nm (43 - 60 in. 1bs.)Applicable to working pressure more than25 MPa (3630 PSI): 6 - 7 Nm (52 - 60 in. 1bs.)Solenoid RatingsValve TypeCoilTypeElectric 40ShocklessTypeDC (K Series )AC DC Rectified (R )D12D24D48R100R2006050605060506050/60Voltage (V)Source Ratin g Serviceable Range10080 - 11010090 - 12011096 - 132120108 - 144200160 - 220200180 - 240220192 - 264240216 - 2881210.8 - 13.22421.6 - 26.44843.2 - 52.810090 - 110200180 - 220Current & Power at Rated VoltageInrush (A) 2 Holding (A)Power 3290.16EDSG-01 Series SolenoidOperated Directional ValvesDescriptions1. AC solenoid is not available in shockless type.R type models with built-in current rectifier is recommended for shockless operation with AC power.2. Inrush current in the above table show rms values at maximum stroke.3. There are more coil types other than the above. For details, please make inquiries.The coil type numbers in the shaded column are handled as opotinal extras.In case these coils are required to be chosen, please confirm the time ofdelivery with us before ordering. OptionsLock Nut Push Button with Lock NutCan be used for manual changeover of spool. The push buttoncan be locked in the pressed condition.SOL bPush Button Plug-in Connector with Solenoid Indicator LightThese are the indicator light incorporated plug-in connectortype solenoids. Energisation or de-energisation of the solenoidcan be easily identified with the incorporated indicator light.Plug-in ConnectorWith Indicator LightSOL bDSG-01 Series Solenoid Operated Directional Valves345
Model Number DesignationFSpecialSealsSShocklessType- 01DSGSeriesNumberValveSize-2Numberof entC:SpringCentred2SpoolTypeA-D24Special TwoPosition ValveOmit if notrequired2, 34, 4060, 910, nection-70-LDesignNumberModels withReverse Mtg. ofSolenoidOmit if notrequiredNone:JapaneseStd. verridePinNone:TerminalBox Type90:N.AmericanDesign Std.DC:None:StandardTypeF:For PhosphateEster TypeFluids(Omit if tred2:TwoPositionsB:SpringOffset238242AB11(AC DC)R100R200DC:D12D24D48C:PushButtonandLock Nut(Option)70N:Plug-inConnectorType2N1 AC DC)R100R200 1. In case of the special two position valve, please refer to page 352 for details. 2. N1 is not available for R type solenoids.In the table above, the symbols or numbers highlighted with shade represent the optionalextras. The valves with model number having such optional extras are handles as options,therefore, please confirm the time of delivery with us before ordering.346DSG-01 Series Solenoid Operated Directional ValvesNone:JapaneseStd. "JIS"andEuropeanDesignStd.L90:N. AmericanDesignStd.L
DIRECTIONAL CONTROLS List of Standard Models and The Maximum Flow-AL /minSpool-Spring ArrangementNo. of Valve PositionsMax. Flow[Port "B" Blocked]ModelNumbersGraphicSymbols10DSG 01 3C2abPTABDSG 01 3C3abPTABDSG 01 3C4aDSG 01 3C40abPTABSpring CentredBPTWorking Pressure MPaA BThree PositionsAbPTABDSG 01 3C60baPT162531. 5ABABPTPT100100100Working Pressure MPaWorking Pressure MPa35101625100（43）100（41） 80（21）57（38） 53（31） 7）100（77） 70（46） 70（46） 70（46）90（63） 90（63） 90（63） 90（63） 90（63） 45（30） 45（30） 45（30）90 90（22） 35（18） 100（38） 76（28） 67（15）909090（26） 43（14） 30（11） 50（31） 38（20） 20（10）85 80（40） 80（22） 85（40） 85（35） 85（24）85858080 80（30） 63（15） 25（10） 70（26） 50（24） 32（16）43（23） 43（23） 42（23） 42（23） 42（23） 54（32） 54（32） 52（32）40（23） 40（23） 38（23） 36（23） 35（23） 48（30） 47（30） 47（30）100[Port "A" Blocked]10031. 3510162538（15） 100（43）100（41） 80（21）13（9） 57（38） 53（31） 29（17）70（46） 70（46） 70（46） 70（46）45（30） 45（30） 45（30） 45（30）35（7） 100（38） 76（28） 67（15）12（5） 50（31） 38（20） 20（10）55（12） 85（40） 85（35） 85（24）18（10） 70（26） 50（24） 32（16）52（32） 54（32） 54（32） 52（32）47（30） 48（30） 47（30） 47（30）31. 08ABDSG 01 BDSG 01 3C10aPTABDSG 01 3C11aPTABDSG 01 3C12aNo-SpringDetentedDSG 01 （18）62（13）15（10）50（45） 50（42） 45（40） 45（40）45（21） 45（16） 38（13）a5045PT50（45） 50（42） 45（40） 45（40）36（18） 28（13） 22（12）ABSpring OffsetTwo PositionsPT100 37）100（20） 78（16） 62（13） 100（50）100（37）100（20） 78（16）100（70） 80（20） 70（20） 40（19） 100（37） 55（25） 29（14） 20（11） 15（10） 100（37） 55（25） 29（14） 20（11）100（65） 85（52） 72（45） 65（34）51310202310010010010070（50） 57（40） 50（25） 43（19）100 37）100（20） 78（16） 62（13） 100（50）100（37）100（20） 78（16）100（70） 80（20） 70（20） 40（19） 100（37） 55（25） 29（14） 20（11） 15（10） 100（37） 55（25） 29（14） 20（11）DSG 01 ��―――2617131110PTABDSG 01 2B3PTABDSG 01 8）80（70）70（48）45（10）10（5）EDSG-01 Series SolenoidOperated Directional Valves Models with AC Solenoids: ��10）7（5）Notes: 1. The relation between the maximum flow in the table above and the frequency/voltage (within the serviceable voltage) is as shown below.( Example )50 Hz, At minimum serviceable voltage(80% of rated voltage)50 Hz, At rated voltageThe maximum flow rate is constantregardless of 50 Hz or 60 Hz and ofany voltage variants within theserviceable voltage60 Hz, At rated voltage2. For the maximum flow rate in P T of the valves with a100100 (43)57 (38)60 Hz, At minimum serviceable voltage(90% of rated voltage)mark, please see page 351.The valve models with a mark are handled asOptions. If you choose such valves, check the timeof delivery beforehand.DSG-01 Series Solenoid Operated Directional Valves347
List of Standard Models and The Maximum Flow Models with DC or R Type Solenoids: DSG-01--D /RL /miSpool-Spring ArrangementNo. of Valve PositionsMax. Flow[Port "B" Blocked]ModelNumbersGraphicSymbolsABPTWorking Pressure MPaa10162531. 00bABaPTaSpring CentredThree PositionsABaPTTPTWorking Pressure MPa3510162531. 75652317221875651913221875651712PTDSG 01 3C60P31. 5ABaB25PTDSG 01 3C40A16ABDSG 01 3C4B10PTDSG 01 3C3AWorking Pressure MPaA BDSG 01 3C2[Port "A" Blocked]ABDSG 01 3C9aPTABDSG 01 3C10aPTABDSG 01 3C11aPTABDSG 01 3C12aNo-SpringDetentedDSG 01 070707070b808080808020b7070707070ABSpring OffsetTwo PositionsPTDSG 01 2B2PTABDSG 01 2B3PTABDSG 01 2B8bPT463275655335Notes: 1. The relation between the maximum flow in the table above and the voltage (within the serviceable voltage) is as shown be low.( Example )At rated voltage[after temperature rise and saturated]The maximum flow rate is constantregardless of any voltage variantswithin the serviceable voltage1002. For the maximum flow rate in P T of the valves with a10055At minimum serviceable voltage(90% of rated voltage)[after temperature rise and saturated]mark, please see page 351.The valve models with a mark are handled asOptions. If you choose suce valves, check the timeof delivery beforehand.348DSG-01 Series Solenoid Operated Directional Valves
DIRECTIONAL CONTROLS List of Standard Models and The Maximum Flow Models with AC Solenoids: DSG-01--ASpool-Spring ArrangementNo. of Valve PositionsMax. FlowU.S.GPM[Port "B" Blocked]ModelNumbersGraphicSymbolsABPTWorking Pressure PSI[Port "A" Blocked]ABABPTPTWorking Pressure PSIWorking Pressure PSI1450 2320 3630 4570 5080 1450 2320 3630 4570 5080 1450 2320 3630 4570 5080DSG 01 3C2abPTABDSG 01 3C3abPTABDSG 01 3C4aDSG 01 3C40abSpring CentredThree PositionsPTABbPTABDSG 01 3C60baPT26.4(11.4) 26.4(10.8) 21.1(5.6) 15.9(4.5) 10.0(4.0) 26.4(11.4) 26.4(10.8) 21.1(5.6) 15.9(4.5) 10.0(4.0)15.1(10.0) 14.0(8.2) 7.7(4.5) 5.0(2.6) 3.4(2.4) 15.1(10.0) 14.0(8.2) 7.7(4.5) 5.0(2.6) 3.4(2.4)26.4(21.1) 26.4(21.1) 26.4(21.1) 26.4(21.1) 26.4(21.1) 18.5(12.2) 18.5(12.2) 18.5(12.2) 18.5(12.2) 18.5(12.2) 18.5(12.2) 18.5(12.2) 18.5(12.2) 18.5(12.2) 18.5(12.2)23.8(16.6) 23.8(16.6) 23.8(16.6) 23.8(16.6) 23.8(16.6) 11.9(7.9) 11.9(7.9) 11.9(7.9) 11.9(7.9) 11.9(7.9) 11.9(7.9) 11.9(7.9) 11.9(7.9) 11.9(7.9) 11.9(7.9)23.8 23.8(5.8) 9.2(4.8) 26.4(10.0) 20.1(17.4) 17.7(4.0) 15.1(2.6) 9.2(1.8) 26.4(10.0) 20.1(7.4) 17.7(4.0) 15.1(2.6) 9.2(1.8)23.823.823.8(6.9) 11.4(3.7) 7.9(2.9) 13.2(8.2) 10.0(5.3) 5.3(2.6) 4.2(1.9) 3.2(1.3) 13.2(8.2) 10.0(5.3) 5.3(2.6) 4.2(1.9) 3.2(1.3)22.522.522.5 21.1(10.6) 21.1(5.8) 22.5(10.6) 22.5(9.3) 22.5(6.3) 15.9(4.2) 14.5(3.2) 22.5(10.6) 22.5(9.3) 22.5(6.3) 15.9(4.2) 14.5(3.2)21.121.1 21.1(7.9) 16.6(4.0) 6.6(2.4) 18.5(6.9) 13.2(6.3) 8.5(4.2) 5.8(3.4) 4.8(2.6) 18.5(6.9) 13.2(6.3) 8.5(4.2) 5.8(3.4) 4.8(2.6)11.4(6.1) 11.4(6.1) 11.1(6.1) 11.1(6.1) 11.1(6.1) 14.2(8.4) 14.2(8.4) 13.7(8.4) 13.7(8.4) 13.7(8.4) 14.2(8.4) 14.2(8.4) 13.7(8.4) 13.7(8.4) 13.7(8.4)10.6(6.1) 10.6(6.1) 10.0(6.1) 9.5(6.1) 9.2(6.1) 12.7(7.9) 12.4(7.9) 12.4(7.9) 12.4(7.9) 12.4(7.9) 12.7(7.9) 12.4(7.9) 12.4(7.9) 12.4(7.9) 12.4(7.9)26.426.426.426.426.4ABDSG 01 02.62.62.1PTABDSG 01 3C10aPTABDSG 01 3C11abPTABDSG 01 3C12abNo-SpringDetentedDSG 01 )15.9(7.1)9.2(4.8)16.4(3.4)4.0(2.6)13.2(11.9) 13.2(11.1) 11.9(10.6) 11.9(10.6)11.9(5.6) 11.9(4.2) 10.0(3.4)a13.2PT9.5(4.8) 7.4(3.4) 5.8(3.2)ABSpring OffsetTwo PositionsPT26.4 26.4(16.6) 26.4(8.7) 26.4(7.1) 26.4(13.2) 26.4(9.8) 26.4(5.3) 20.6(4.2) 16.4(3.4) 26.4(13.2) 26.4(9.8) 26.4(5.3) 20.6(4.2)26.4(18.5) 21.1(5.3) 18.5(5.3) 10.6(5.0) 26.4(9.8) 14.5(6.6) 7.7(3.7) 5.3(2.9) 4.0(2.6) 26.4(9.8) 14.5(6.6) 7.7(3.7) 5.3(2.9)26.4(17.2) 22.5(13.7) 19.0(13.7) 3.2) 15.1(10.6) 13.2(6.6) 11.4(5.0)26.4 26.4(16.6) 26.4(8.7) 26.4(7.1) 26.4(13.2) 26.4(9.8) 26.4(5.3) 20.6(4.2) 16.4(3.4) 26.4(13.2) 26.4(9.8) 26.4(5.3) 20.6(4.2)26.426.4(18.5) 21.1(5.3) 18.5(5.3) 10.6(5.0) 26.4(9.8) 14.5(6.6) 7.7(3.7) 5.3(2.9) 4.0(2.6) 26.4(9.8) 14.5(6.6) 7.7(3.7) 5.3(2.9)DSG 01 9PTABDSG 01 2B3PTABDSG 01 2B8PT13.2(11.9) 13.2(11.1) 11.9(10.6) 11.9(10.6)EDSG-01 Series SolenoidOperated Directional ValvesA B22.5(16.6) 21.1(13.2) 16.6(10.6) 11.6(8.5) 11.6(8.5)22.5(7.9) 15.9(8.7) 13.2(7.4) 10.6(7.4) 10.6(7.4)21.1(18.5) 21.1(18.5) 21.1(18.5) 21.1(18.5) 21.1(18.5)13.218.5(12.7) 18.5(12.7) 18.5(12.7) 18.5(12.7) 18.5(12.7)21.1(13.2) 18.5(10.6) 15.9(5.3) 11.9(2.6) 7.9(2.6)2.69.2(5.3) 6.1(4.0) 4.0(2.1) 2.6(1.3) 1.9(1.3)3.4Notes: 1. The relation between the maximum flow in the table above and the frequency/voltage (within the serviceable voltage) is as shown below.( Example )50 Hz, At minimum serviceable voltage(80% of rated voltage)50 Hz, At rated voltageThe maximum flow rate is constantregardless of 50 Hz or 60 Hz and ofany voltage variants within theserviceable voltage60 Hz, At rated voltage2. For the maximum flow rate in P T of the valves with a26.426.4(11.4)15.1(10.0)60 Hz, At minimum serviceable voltage(90% of rated voltage)mark, please see page 351.The valve models with a mark are handled asOptions. If you choose such valves, check the timeof delivery beforehand.DSG-01 Series Solenoid Operated Directional Valves349
List of Standard Models and The Maximum Flow Models with DC or R Type Solenoids: DSG-01--D /RSpool-Spring ArrangementNo. of Valve PositionsMax. FlowU.S.GPM[Port "B" Blocked]ModelNumbersGraphicSymbolsABPTWorking Pressure PSI[Port "A" Blocked]ABABPTPTWorking Pressure PSIWorking Pressure PSI1450 2320 3630 4570 5080 1450 2320 3630 4570 5080 1450 2320 3630 4570 5080A BDSG 01 3C2ab26.426.426.426.426.4PTABDSG 01 3C3abPTABDSG 01 3C4abSpring CentredThree PositionsPTABDSG 01 3C40abPTABDSG 01 3C60baPT26.4 26.4 26.4 26.4 26.421.1 21.1 21.1 21.1 21.123.8 13.2 10.023.8 23.85.311.1 6.917.2 10.6 8.722.5 22.56.911.9 7.913.3 13.3 13.3 13.3 13.310.8 10.8 10.8 10.8 35.8 26.414.54.519.8 20.618.5 18.57.7 26.46.1 16.46.3 22.55.0 17.217.4 17.415.3 5.617.415.35.84.519.818.57.76.16.35.017.415.3ABDSG 01 3C9ab26.426.4 6.35.0b26.426.4 10.6 26.45.3 .03.45.84.819.817.24.53.2PTABDSG 01 3C10aPTABDSG 01 3C11aPTABDSG 01 3C12aNo-SpringDetentedDSG 01 .121.121.121.121.15.3b18.518.518.518.518.5ABSpring OffsetTwo PositionsPTDSG 01 2B2PTABDSG 01 2B3PTABDSG 01 2B8bPT12.28.519.817.214.09.3Notes: 1. The relation between the maximum flow in the table above and the voltage (within the serviceable voltage) is as shown be low.( Example )At rated voltage[after temperature rise and saturated]The maximum flow rate is constantregardless of any voltage variantswithin the serviceable voltage26.42. For the maximum flow rate in P T of the valves with a26.414.5At minimum serviceable voltage(90% of rated voltage)[after temperature rise and saturated]mark, please see page 351.The valve models with a mark are handled asOptions. If you choose suce valves, check the timeof delivery beforehand.350DSG-01 Series Solenoid Operated Directional Valves
DIRECTIONAL CONTROLSMaximum Flow of Centre By-PassIn valve type 3C60, in case where the actuator is put on in between the cylinder ports A and B as illustrated below andwhere the actuator moves and suspended at its stroke end and where the valve is then shifted to the neutral position inthe suspended state of the actuator, the maximum flow rates available are those as shown as the table below regardlessof any voltage in the range of serviceable valtage.Max. FlowGraphicSymbolMode NumbersAB55(14.5)baDSG-01-3C60-A /D /RL/min (U.S.GPM)10 MPa16 MPa25 MPa31.5 MPa35 MPa(1450 PSI) (2320 PSI) (3630 PSI) (4570 PSI) (5080 PSI)PT44(11.6)30(7.9)26(6.9)22(5.8)EList of Shockless Models and The Maximum Flow-D /RL/min (U.S.GPM)Max. Flow[Port "B" Blocked]No. olModel NumbersABPTWorking PressureMPa .6)20(5.3)45(11.9)40(10.6)A T50(13.2)45(11.9)[Port "A" Blocked]ABABPTPTWorking PressureMPa (PSI)101625(1450) (2320) (3630)Working PressureMPa (PSI)101625(1450) (2320) 30(7.9)60(15.9)40(10.6)40(10.6)DSG-01 Series SolenoidOperated Directional ValvesModels with DC or R Type Solenoids: S-DSG-01-Notes: 1. The relation between the maximum flow in the table above and the voltage (within the serviceable voltage) is as shown be low.L/min( Example )The maximum flow rate is constantregardless of any voltage variantswithin the serviceable voltage60(15.9)50(13.2)40(10.6)At rated voltage[after temperature rise and saturated]At minimum serviceable voltage(90% of rated voltage)[after temperature rise and saturated]U.S.GPMDSG-01 Series Solenoid Operated Directional Valves351
Reverse Mounting of Solenoid.In spring offset type, it is a standard configuration that the solenoid is mounted onto the valve in the SOL b position(side). However, in this particular spool-spring arrangement, the mounting of the solenoid onto the valve in the reverseposition -SOL a side- is also available. The graphic symbol for this reverse mounting is as shown below.As for the valve type 2B A and 2B B, please refer to the explanation under the heading of "Valves Using NeutralPosition and Side Position" given below.ABPTSOL bbABPTSOL aaStandard Mtg. of SolenoidReverse Mtg. of SolenoidValves Using Neutral Position and Side Position. (Special Two position Valve)Besides the use of the standard 2-position valves aforementioned in the "List of Standard Models and Maximum Flow",the 3-position valves also can be used as the 2-position valves using the two of their three positions. In this case, thereare two kinds of the valve available. One is the valve using the neutral position and SOL a position (2B A) and anotheris the valve using the neutral position and SOL b position (2B B) .(Example) In case of Spool Type "2"Neutral PositionSOL. b EnergisedPositionSOL. a EnergisedPositionABbaPT2B2AABPTABPT2B2Bbb"A": Use of Neutral andSOL. a EnergisedPosition (2B2A)"B": Use of Neutral andSOL. b EnergisedPosition (2B2B)Graphic SymbolsGModel NumbersStandardMtg. TypeAAbPDSG-01-2B2AReverseMtg. TypeBDSG-01-2B ATraphic SymbolsModel NumbersStandardMtg. TypeABBDSG-01-2B BDSG-01-2B10BIn the above table, the graphic symbols in mountingtype highlighted with shade are optional extra,therefore, please confirm the time of delivery withus before ordering.352ReverseMtg. TypeDSG-01 Series Solenoid Operated Directional ValvesTABPTa
DIRECTIONAL CONTROLSTypical Changeover TimeChangeover time varies according to oil viscosity, spool type and hydraulic circuit.Standard Type (Without Shockless Function)[Result of Measurement][Test Conditions ]Pressure:Flow Rate:Viscosity:Voltage:16 MPa (2320 PSI)31.5 L /min (8.3 U.S.GPM)35 mm 2 /s (164 SSU)100 %V(After coil temprature rises and saturated)ONSolenoidOF FO FF00Spool ShiftMax.T2TypeModel NumbersStandardTypeDSG-01-3C2- ADSG-01-3C2- DDSG-01-3C2- RTime msT1T21548502319100Shockless Type[Reaults of Measurement][Test Circuit and Conditions]AccelmeterOF FONSOL aSpeedG1abG2Acceleration (G)LoadPressure (Ps)PsT1Setting Pressure (Ps): 7 MPa (1020 PSI)Load (W): 1000 kg (2205 1bs.)Speed: 8 m/min (26.2 ft./min)Viscosity: 35 mm 2 /s (164 SSU )TypeT2TimeModel NmbersTime Acceleratio nmsm/s2 (G)T1 T2G1G2Shockles sTypeS-DSG-01-3C2- D70 3012(1.2 )7(0.7 )StandardTypeDSG-01-3C2- D35 2518(1.8 )15(1.5 )DSG-01 Series Solenoid Operated Directional ValvesEDSG-01 Series SolenoidOperated Directional ValvesT1353
Pressure DropPressure drop curves based on viscosity of 35 mm2 /s (164 SSU) and specific gravity of 0.850.Standard Type: DSG-01PSI6001MPa4Model Numbers2B TP BA 0 53Pressure Drop P5003400300220011000200040486012801620Pressure Drop Curve NumberP A24Flow Rate4Shockless Type: S-DSG-01PSI180MPa1.211601208020.80.6Pressure Drop Curve NumberP AB TP BA .0PPressure DropModel .GPMFlow RateFor any other viscosity, multiply the factors in the table below.Viscositymm 2/s 15FactorSSU77405060708090100203098141 186 232 278 324 371 417 4640.81 0.87 0.96 1.03 1.09 1.14 1.19 1.23 1.27 1.30For any other specific gravity (G'), the pressure drop ( P') may beobtained from the formula below.P' P (G'/0.850)354DSG-01 Series Solenoid Operated Directional ValvesP T22
DIRECTIONAL CONTROLSMounting surface: ISO 4401-AB-03-4-ATERMINAL BOX TYPEModels with AC SolenoidsSingle Solenoid: Spring OffsetDSG-01-2B -A -70/7090Double Solenoid: Spring Centred & No-Spring Detented3C -A -70/7090DSG-01- 2D2Solenoid Indicator Light(For Sol a)145.7(5.74)Pressure Port "P"Cylinder Port "A"76.7(3.02)142.2(5.60)Solenoid Indicator Light(For Sol b)196.4(7.73)95(3.74)26(1.02)50.7(2.00)For other dimensions, refer to "spring Centred andNo-Spring Detented" models.Solenoid being mounted in the reverse positionSOL a side is also available.46(1.81)A100SOL aSOL bA13.5(.53)70(2.76)38(1.50)3Mounting Surface(O-Rings Furnished)Lock NutTightening Torque:10.3-11.3 Nm (91-100 IN.lbs.)XESpace Needed to RemoveSolenoid-Each End45.5Electrical Conduit Connection"C " Thd. (Both Ends)(1.79)533(1.30)23.5 47(1.85)(.93)88.8(3.50)Tank Port "T"TBAP27(1.06)Manual Actuator-Both Ends6(.24) Dia.3(.12) Dia. 5(.20) DeepVIEW ARROW X Locating pin can be fitted to this hole to conform withModel Numbers"C " Thd.DSG-01--A -70DSG-01--A -7090 1/2 NPTG 1/2DSG-01 Series SolenoidOperated Directional ValvesCylinder Port "B"SOL b31.75(1.25)40.5(1.59)31 0.75(1.22) (.03)32.5(1.28)5.5(.22) Dia. Through9.5(.37) C' Bore4 PlacesISO4401-03-02-94. However, locating pin is not providedto standard design valve. When ordering valve with alocating pin, please consult Yuken.DIMENSIONS INMILLIMETRES (INCHES)Models with DC Solenoids: (S-)DSG-01-D -70/7090Models with R Type Solenoids: (S-)DSG-01-R -70/7090Spring CentredNo-Spring DetentedSpring OffsetSpace Needed to RemoveSolenoid-Each SOL bD3Double SolenoidModels Only5Spring Offset Type 146.2(5.76)For other dimensions, refer to models with AC solenoids.DSG-01 Series Solenoid Operated Directional Valves355
Sub-plate : 30)12.7(.50)"C" Thd.4 PlacesPDSGM-01-31"E"mm(IN.)M510 (.39)No.10-24 UNC12 (.47)M510 (.39)No.10-24 UNC12 (.47)Rc 3/8M510 (.39)3/8 NPTNo. 10-24 UNC12 (.47)Rc 1/8DSGM-01-31801/8 BSP.FDSGM-01-31901/8 NPTDSGM-01X-31Rc 1/4DSGM-01X-31801/4 BSP.FDSGM-01X-31901/4 NPTDSGM-01Y-31DSGM-01Y-3190T11(.43)"D" Thd.Piping Size"C" Thd.DSG-01 Series Solenoid Operated Directional ValvesBA37(1.46)24(.94)7 (.28) Dia. Through7(.28) 11 (.43) Dia. Spotface2 PlacesSub-plateModel )"D" Thd. "E" Deep4 Places0.75(.03)15.5(.61)7 (.28) Dia.4 Places40.5(1.59)30.2(1.19)21.5(.85)DIMENSIONS INMILLIMETRES (INCHES)12.5(.49)35.5(1.40)58.5(2.30)
DIRECTIONAL CONTROLSPLUG-IN CONNECTOR TYPE (N)PLUG-IN CONNECTOR WITH INDICATOR LIGHT (N1)DIMENSIONS INMILLIMETRES (INCHES)-A - N -70/7090N1Models with DC Solenoids: (S-)DSG-01-D - N -70/7090N1Models with R Solenoids: (S-)DSG-01-R -N-70/7090Models with AC Solenoids: DSG-01-SOL bA100Double SolenoidModels Only23.5(.93)SOLaHLock NutTightening Torque:10.3 - 11.3 Nm (90 - 100 IN.lbs.)C196.4(7.73)204.4(8.05)204.4(8.05)Model NumbersDSG-01--A -N(S-)DSG-01--D -N(S-)DSG-01--R .92)102.5(4.04)F53(2.09)64(2.52)57.2(2.25)EGH27.5 39(1.08) (1.54)27.5 39(1.08) (1.54)3453(1.34) (2.09)DSG-01 Series SolenoidOperated Directional ValvesD29.5(1.16)72.5(2.85)ECFThe position of the Plug-in connector can be changed asillustrated below by loosening the lock nut. AfterCable Departurecompletion of the change, be sure to tighten the lock nutwith the torque as specified below.Cable Applicable:Outside Dia. . 8 - 10 mm (.31 - .39 in.)Conductor Area .46(1.81)Not Exceeding 1.5 mm2 (.0023 Sq. in.)GFor other dimensions, refer to "Terminal Box type" (Page 356).Models with Push Button & Lock Nut(S-)DSG-01-- -CAC: 132.2(5.20)DC/R: 136.2(5.36)Lock NutPress the "Push Button" then turn "Lock Nut"clockwise. The position of the "Push Button" is held.Be sure to loosen "Lock Nut" fully before solenoidis energised.SOL bPush ButtonInterchangeability in Installation Current and New DesignIn ouder to achieve higher pressure, higher flow, lower pressure drop DSG-01 valves has been upgraded from the 60design series to the 70 design series.The figures in the table below are the comparison between the current and the new design valves. SpecificationsDesign NumberMax. FlowL/min(U.S.GPM)Max. OperatingPressureMPa (PSI)Max. T-LineBack Pres.MPa (PSI)New Design: 70100(26.4)35(5080)21(3050)Current Design: 6063(16.6)31.5(4570)16(2320)Pressure Drop MPa (PSI){P A}Max. ChangeoverFrequencyCycle/min (min–1)300(R Type sol. Only 120)Mass kg (lbs.)3C .6(3.53) Flow Rate: 60 L/min (15.9 U.S.GPM), Viscosity: 30 mm2/s (141 SSU), Spool type "2" (Closed centre) Interchangeability in InstallationInterchangeability in installation in maintained though there are minor differences in demension as in the following table.AEFCoil TypeCHACA38(1.50)3KJBDLA100SOL bSOL a527(1.06)DCRDesignNumberNew Design: 70ABCDEFHJKL196.4 142.2 4688.89550.7267013.5 70.5(7.73) (5.60) (1.81) (3.50) (3.74) (2.00) (1.02) (2.76) (.53) (2.78)Current Design 191.4 142.7 4890.39050.7 23.5651172: 60(7.54) (5.62) (1.89) (3.56) (3.54) (2.00) (.93) (2.56) (.43) (2.83)New Design: 70204.4 146.2 4688.89554.7267013.5 70.5(8.05) (5.76) (1.81) (3.50) (3.74) (2.15) (1.02) (2.76) (.53) (2.78)Current Design 210 1524890.3906023.5651172: 60(8.27) (5.98) (1.89) (3.56) (3.54) (2.36) (.93) (2.56) (.43) (2.83)DSG-01 Series Solenoid Operated Directional Valves357
Details of ReceptacleType ofElectrical ConduitConnectionDouble Solenoid TypeSingle Solenoid Type3Power Supply(For SOL.a)Power Suppl y1Power Supply(For SOL.b)SOL. aSOL. bGround33Indicator LightTerminalBox TypeCommon Plate2SOL. bIndicator LightIndicator LightCommonGround31Groun
1/8 Solenoid Operated Directional Valves, DSG-01 Series These are Solenoid Operated Directional Valves of high pressure, high flow and low pressure drop, the features of which can be materialized . A120
Solenoid Controlled Pilot Operated Directional Valves Solenoid Controlled Pilot Operated Directional Valves These valves are composed of a solenoid operated pilot valve and a pilot operated slave valve. When a solenoid is energised the pilot valve directs the flow to move the spool of the slave valve, thus changing the direction of flow in the .
S - 5,20 bar (75 psi) check Solenoid Energization Identity Blank - Standard arrangement for ANSI B93.9 (i.e. energize solenoid A to follow flow P to A). V - Solenoid identification determined by position of solenoid (i.e. solenoid A at port A end/solenoid B at port B end). Note 4 and 8 type spools are always V. Solenoid
LVM09/090 2/3 port direct operated solenoid Cv 0.018 139 LVM10/100 2/3 port direct operated solenoid Cv 0.03 0.04 139 LVM15/150 & -20/200 2/3 port direct operated solenoid valve Cv 0.015 0.065 140 VDW10, -20 & -30 2/2 solenoid Cv 0.03 0.44 141 VDW200 & -300 3/2 solenoid Cv 0.03 0.44 142 VCA solenoid valve Cv 0.33 2.1 143 N
DSG-03 Series Solenoid Operated Directional Valves E DSG-03 Series Solenoid Operated Directional Valves Specifications Valve Type AC Model Numbers Max. Flow L/min (U.S.GPM) Max. Operating Pressure MPa (PSI) Max. T-Line Back Pres. MPa (PSI) Max. Changeover Frequency min (Cycles/Min)-1 DC, R, RQ Type of Solenoid Approx. Mass kg(1bs.) DSG-03-3C .
SOLENOID CONTROLLED PILOT Up to 31.5 MPa (4570 PSI), 1100L/min (291 U.S.GPM) Pub. EC-0404 PILOT OPERATED DIRECTIONAL VALVES OPERATED DIRECTIONAL VALVES . Pilot Drain Port for Solenoid Controlled Pilot Operated Directional Valve Avoid connecting the valve pilot drain port to a line with
DC-41DT 12V DC Solenoid Operated Power Up/Power Down . . . . . 99 DC-50SF 12V DC Manual Operated Power Up/Power Down . . . . . 100 DC-60SF 12V DC Solenoid Operated Power Up/Power Down . . . . 101 DC-62SF 12V DC Solenoid Operated Dual Power Up/Power Down . . 102 DC-70SF 12V DC Solenoid Operated Power Up/Power Down . . . . 103
Series 35- Solenoid Pilot Operated Directional Valves 31341 Friendship Drive, Magnolia, TX 77355 Tel.: 281-259-7768 Fax: 281-259-7249 www.hyvair.com CROSS SECTION CROSS SECTION DRAWING 1) Main vVal e with Housing 2) Main Control Spool 3.1) Return Spring 3.2) Return Spring 4) Pilovet Val 5.1) Solenoid 5.2) Solenoid 6) Spring Chamber
For first award of AS level in Summer 2017 For first award of A level in Summer 2018 Subject Code: 3210 CCEA GCE Specification in Business Studies Version 3: 13 November 2018. Version 3: 8 November 2018 . Contents . 1 Introduction 3 . 1.1 Aims 4 1.2 Key features 4 1.3 Prior attainment 4 1.4 Classification codes and subject combinations 4 . 2 Specification at a Glance 5 3 Subject Content 6 . 3 .
