AUTOMATIC TRANSMISSION - AUTOMATIC TRANSMISSION SYSTEM .
AT-1AUTOMATIC TRANSMISSION-AUTOMATIC TRANSMISSION SYSTEMAUTOMATIC TRANSMISSION SYSTEMAT0HC-01PRECAUTIONIf the vehicle is equipped with a mobile communication system, refer to the precautions in the IN section.2005 LEXUS IS300 (RM1140U)Author :Date :1623
AT-2AUTOMATIC TRANSMISSION-AUTOMATIC TRANSMISSION SYSTEMAT05W-05OPERATION3rd Coast Brake (B1)Direct Clutch (C2)Forward Clutch (C1)O/D One-way3rd Brake (B2)Clutch (F0)No. 1 One-way Clutch (F1)2nd Brake (B3)1st & Reverse Brake (B4)No. 2 One-way Clutch (F2)O/D Direct Clutch (C0)O/D Brake (B0)Shift Solenoid Valve No. 2Shift Solenoid Valve No. 1Shift Solenoid Valve No. 3Shift Solenoid Valve SLTShift Solenoid Valve SLUShift Solenoid Valve SLNShift Solenoid Valve No. 4D09398Shift LeverPositionPRNDM arkON OFF ON OFFReverse ON OFF OFF OFFNeutralON OFF ON OFF1stON OFF OFF OFF2ndON ON OFF OFFOFF ON OFF OFF3rd4thOFF OFF ON OFF5thOFF OFF OFF ON1stON OFF OFF OFF2ndON ON OFF OFF3rdOFF ON ON OFF1stON OFF ON OFF2ndON ON OFF OFF1stON OFF OFF OFF: Operating* : When the shift lever position is ”M” and the gear position indicator shows ”5”.2005 LEXUS IS300 (RM1140U)Author :Date :1624
AT-3AUTOMATIC TRANSMISSION-EXTENSION HOUSING OIL SEALEXTENSION HOUSING OIL SEALAT0HE-02ON-VEHICLE REPAIR1.2.3.4.5.REMOVE NO. 1 AND NO. 2 ENGINE UNDER COVERSREMOVE LH FRONT FLOOR CENTER COVERREMOVE NO. 1 REAR FLOOR BOARDREMOVE EXHAUST PIPE ASSEMBLY(See page EM-100 )REMOVE PROPELLER SHAFT (See page PR-4 )6.REMOVE REAR OIL SEALUsing SST, remove the oil seal.SST 09308-00010SSTD050527.(a)SSTOR0005INSTALL NEW OIL SEALUsing SST and a hammer, carefully drive a new oil sealin as far as it will go.SST 09325-20010NOTICE:Clean the extension housing before removing the oil seal.(b) Coat the lip of a new oil seal with MP grease.8.INSTALL PROPELLER SHAFT (See page PR-10 )9.INSTALL EXHAUST PIPE ASSEMBLY(See page EM-100 )10. FILL ATF AND CHECK FLUID LEVEL(See page DI-338 )11. REMOVE NO. 1 REAR FLOOR BOARD12. REMOVE LH FRONT FLOOR CENTER COVER13. INSTALL NO. 1 AND NO. 2 ENGINE UNDER COVERS2005 LEXUS IS300 (RM1140U)Author :Date :1625
AT-4AUTOMATIC TRANSMISSION-SENSOR ROTORSENSOR ROTORAT0HF-02ON-VEHICLE REPAIR1.2.3.4.5.6.7.RAISE VEHICLE AND POSITION PAN TO CATCH ANYFLUID THAT MAY DRIPREMOVE NO. 1 AND NO. 2 ENGINE UNDER COVERSREMOVE LH FRONT FLOOR CENTER COVERREMOVE NO. 1 REAR FLOOR BOARDREMOVE EXHAUST PIPE (See page EM-100 )REMOVE PROPELLER SHAFT (See page PR-4 )REMOVE VEHICLE SPEED SENSOR (See pageAT-7 )8.JACK UP TRANSMISSION SLIGHTLYSecurely support the transmission on a transmission jack.Lift the transmission slightly from the rear support member.AT12149.(a)(b)REMOVE ENGINE REAR SUPPORT MEMBERRemove the 4 nuts.Remove the 4 bolts and rear support member.D0483910. REMOVE TRANSMISSION MOUNTING BRACKETRemove the 4 bolts and the transmission mounting bracketfrom the transmission.D048402005 LEXUS IS300 (RM1140U)Author :Date :1626
AT-5AUTOMATIC TRANSMISSION-SENSOR ROTOR11. REMOVE EXTENSION HOUSING(a) Remove the 6 bolts.(b) Remove the extension housing.HINT:If necessary, tap the extension housing with a plastic hammer.(c) Remove the extension housing gasket.D0484112.(a)(b)13.(a)(b)REMOVE SENSOR ROTOR AND KEYUsing a snap ring expander, remove the snap ring.Remove the sensor rotor and key.INSTALL KEY AND SENSOR ROTORInstall the key and sensor rotor.Using a snap ring expander, install a new snap ring.14.(a)(b)INSTALL EXTENSION HOUSINGInstall a new extension housing gasket.Install the extension housing with the 6 bolts.Torque: 34 N·m (345 kgf·cm, 25 ft·lbf)D09387D04841HINT:Coat the thread of the all bolts with sealant.Sealant:Part No. 08833-00080, THREE BOND 1344, LOCTITE242 or equivalent15. INSTALL TRANSMISSION MOUNTING BRACKETInstall the transmission mounting bracket with the 4 bolts to thetransmission.Torque: 12 N·m (120 kgf·cm, 9 ft·lbf)D0484016.(a)(b)17.18.D0483919.INSTALL ENGINE REAR SUPPORT MEMBERInstall the rear support member with the 4 bolts.Torque: 25 N·m (260 kgf·cm, 19 ft·lbf)Install the 4 nuts.Torque: 12 N·m (120 kgf·cm, 9 ft·lbf)REMOVE JACKINSTALL VEHICLE SPEED SENSOR (See pageAT-7 )INSTALL PROPELLER SHAFT (See page PR-10 )2005 LEXUS IS300 (RM1140U)Author :Date :1627
AT-6AUTOMATIC TRANSMISSION20.21.22.23.24.-SENSOR ROTORINSTALL EXHAUST PIPE (See page EM-100 )FILL ATF AND CHECK FLUID LEVEL(See page DI-338 )INSTALL NO. 1 REAR FLOOR BOARDINSTALL LH FRONT FLOOR CENTER COVERINSTALL NO. 1 AND NO. 2 ENGINE UNDER COVERS2005 LEXUS IS300 (RM1140U)Author :Date :1628
AT-7AUTOMATIC TRANSMISSION-VEHICLE SPEED SENSORVEHICLE SPEED SENSORAT0XV-01ON-VEHICLE REPAIR1.2.3.REMOVE NO. 1 AND NO. 2 ENGINE UNDER COVERSREMOVE LH FRONT FLOOR CENTER COVERREMOVE NO. 1 REAR FLOOR BOARD4.DISCONNECT VEHICLE SPEED SENSOR CONNECTORREMOVE VEHICLE SPEED SENSORRemove the bolt and vehicle speed sensor.Remove the O-ring from the vehicle speed sensor.INSTALL VEHICLE SPEED SENSORCoat a new O-ring with ATF and install it to the vehiclespeed sensor.Install the vehicle speed sensor to the extension housingand torque the bolt.Torque: 5.4 N·m (55 kgf·cm, 48 in.·lbf)INSTALL NO. 1 REAR FLOOR BOARDINSTALL LH FRONT FLOOR CENTER COVERINSTALL NO. 1 AND NO. 2 ENGINE UNDER COVERS5.(a)(b)6.(a)D09363(b)7.8.9.2005 LEXUS IS300 (RM1140U)Author :Date :1629
AT-8AUTOMATIC TRANSMISSION-O/D DIRECT CLUTCH SPEED SENSORO/D DIRECT CLUTCH SPEEDSENSORAT0XW-01ON-VEHICLE REPAIR1.2.3.REMOVE NO. 1 AND NO. 2 ENGINE UNDER COVERSREMOVE LH FRONT FLOOR CENTER COVERREMOVE NO. 1 REAR FLOOR BOARD4.DISCONNECT O/D DIRECT CLUTCH SPEED SENSORCONNECTORREMOVE O/D DIRECT CLUTCH SPEED SENSORRemove the bolt and O/D direct clutch speed sensor.Remove the O-ring from the O/D direct clutch speed sensor.INSTALL O/D DIRECT CLUTCH SPEED SENSORCoat a new O-ring with ATF and install it to the O/D directclutch speed sensor.Install the O/D direct clutch speed sensor to the transmission case and torque the bolt.Torque: 5.4 N·m (55 kgf·cm, 48 in.·lbf)INSTALL NO. 1 REAR FLOOR BOARDINSTALL LH FRONT FLOOR CENTER COVERINSTALL NO. 1 AND NO. 2 ENGINE UNDER COVERS5.(a)(b)6.(a)D09364(b)7.8.9.2005 LEXUS IS300 (RM1140U)Author :Date :1630
AT-9AUTOMATIC TRANSMISSION-ATF TEMPERATURE SENSORATF TEMPERATURE SENSORAT05Y-03ON-VEHICLE REPAIRCAUTION:When working with FIPG material, you must observe thefollowing items. Using a razor blade and gasket scraper, remove allthe old FIPG material from the gasket surfaces. Thoroughly clean all components to remove all theloose material. Clean both sealing surfaces with a non-residue solvent. Apply FIPG in an approx. 1 mm (0.04 in.) wide beadalong the sealing surface. Parts must be assembled within 10 minutes of application. Otherwise, the FIPG material must be removed and reapplied.1.REMOVE NO. 1 AND NO. 2 ENGINE UNDER COVERS2.REMOVE LH FRONT FLOOR CENTER COVER3.REMOVE NO. 1 REAR FLOOR BOARD4.REMOVE DRAIN PLUG WITH GASKET AND DRAINATF5.REMOVE OIL PANNOTICE:Some fluid will remain in the oil pan.(a) Remove the 19 bolts.D00910(b)Install the blade of SST between the transmission caseand oil pan, cut off applied sealer, and remove the oil pan.SST 09032-00100NOTICE:When removing the oil pan, be careful not to damage the oilpan flange.SSTQ074872005 LEXUS IS300 (RM1140U)Author :Date :1631
AT-10AUTOMATIC TRANSMISSION-ATF TEMPERATURE SENSOR6.EXAMINE PARTICLES IN PANRemove the magnets and use them to collect steel particles.Carefully look at the foreign matter and particles in the pan andon the magnets to anticipate the type of wear you will find in thetransmission.Steel (magnetic) . bearing, gear and clutch plate wearBrass (non-magnetic) . bushing wearAT01037.REMOVE OIL STRAINERNOTICE:Be careful as some fluid will come out of the oil strainer.(a) Remove the 4 bolts and oil strainer.D09388(b)Remove the 3 gaskets from the oil strainer.8.REMOVE SOLENOID WIRING WITH ATF TEMPERATURE SENSORDisconnect the ATF temperature sensor and remove theO-ring.Remove the bolt and clamp.Disconnect the 7 connectors from the solenoid valves.D00753Clamp(a)(b)(c)D09389(d)9.(a)Remove the bolt, solenoid connector and O-ring.INSTALL SOLENOID WIRING WITH ATF TEMPERATURE SENSORInstall the solenoid connector and a new O-ring with thebolt.Torque: 5.4 N·m (55 kgf·cm, 48 in.·lbf)D009162005 LEXUS IS300 (RM1140U)Author :Date :1632
AT-1 1AUTOMATIC TRANSMISSION(b)(c)(d)-ATF TEMPERATURE SENSORConnect the 7 connectors to the solenoid valves.Install the clamp with the bolt.Torque: 6.4 N·m (65 kgf·cm, 56 in.·lbf)Install a new O-ring and connect the ATF temperaturesensor.D0938910.(a)INSTALL OIL STRAINERInstall 3 new gaskets.(b)Install the oil strainer with the 4 bolts.Torque: 10 N·m (100 kgf·cm, 7 ft·lbf)11.(a)INSTALL OIL PANInstall the 3 magnets in the indications of the oil pan.(b)Remove any packing material and be careful not to dropoil on the contacting surfaces of the transmission caseand oil pan.Apply FIPG to the oil pan.FIPG:Part No. 08826-00090, THREE BOND 1281 orequivalentD00753D09388D00912Seal Breadth 2 - 3 mm (0.08 - 0.12 in.)(c)D019172005 LEXUS IS300 (RM1140U)Author :Date :1633
AT-12AUTOMATIC TRANSMISSION”A”D00910(d)-ATF TEMPERATURE SENSORInstall the oil pan with the 19 bolts.Torque: 7.4 N·m (75 kgf·cm, 65 in.·lbf)HINT:Replace the only ”A” bolt with a new one.12. INSTALL DRAIN PLUG WITH NEW GASKETTorque: 20 N·m (205 kgf·cm, 15 ft·lbf)13. FILL FLUID AND CHECK FLUID (See page DI-338 )14. INSTALL NO. 1 REAR FLOOR BOARD15. INSTALL LH FRONT FLOOR CENTER COVER16. INSTALL NO. 1 AND NO. 2 ENGINE UNDER COVERS2005 LEXUS IS300 (RM1140U)Author :Date :1634
AT-13AUTOMATIC TRANSMISSION-VALVE BODY ASSEMBLYVALVE BODY ASSEMBLYAT05Z-03ON-VEHICLE REPAIRCAUTION:When working with FIPG material, you must observe thefollowing items. Using a razor blade and gasket scraper, remove allthe old FIPG material from the gasket surfaces. Thoroughly clean all components to remove all theloose material. Clean both sealing surfaces with a non-residue solvent. Apply FIPG in an approx. 1 mm (0.04 in.) wide beadalong the sealing surface. Parts must be assembled within 10 minutes of application. Otherwise, the FIPG material must be removed and reapplied.1.REMOVE NO. 1 AND NO. 2 ENGINE UNDER COVERS2.REMOVE LH FRONT FLOOR CENTER COVER3.REMOVE NO. 1 REAR FLOOR BOARD4.REMOVE DRAIN PLUG WITH GASKET AND DRAINATF5.REMOVE OIL PAN (See page AT-9 )6.EXAMINE PARTICLES IN PAN (See page AT-9 )7.REMOVE OIL STRAINER (See page AT-9 )8.REMOVE SOLENOID WIRING WITH ATF TEMPERATURE SENSOR (See page AT-9 )9.REMOVE VALVE BODYRemove the 20 bolts and valve body.D0075410. REMOVE CHECK BALL BODY AND SPRINGNOTICE:Do not drop the check ball body and spring.SpringCheck Ball BodyD093912005 LEXUS IS300 (RM1140U)Author :Date :1635
AT-14AUTOMATIC TRANSMISSIONShift SolenoidValve SLNShift SolenoidValve No. 3Shift SolenoidValve No. 1Shift SolenoidValve SLU11.(a)(b)(c)(d)12.(a)(b)(c)(d)Shift SolenoidValve SLTShift Solenoid Valve No. 4Shift Solenoid Valve No. 2(e)D00911-VALVE BODY ASSEMBLYREMOVE SOLENOID VALVERemove the 3 bolts and shift solenoid valve No. 1, No. 2and No. 3.Remove the 2 bolts, oil guide plate, lock plate, shift solenoid valve SLN and No. 4.Remove the 6 O-rings from each shift solenoid valve.Remove the bolt, lock plate and shift solenoid valve SLUand SLT.INSTALL SOLENOID VALVEInstall the shift solenoid valve SLU and SLT and the lockplate with the bolt.Torque: 6.4 N·m (65 kgf·cm, 56 in.·lbf)Coat 6 new O-rings with ATF.Install the 6 O-rings to the each solenoid valve.Install the shift solenoid valve SLN, No. 4, lock plate andoil guide plate with the 2 bolts.Torque: 10 N·m (100 kgf·cm, 7 ft·lbf)Install the shift solenoid valve No. 1, No. 2 and No. 3 withthe 3 bolts.Torque:Shift solenoid valve No. 1 and No. 3:6.4 N·m (65 kgf·cm, 56 in.·lbf)Shift solenoid valve No. 2:10 N·m (100 kgf·cm, 7 ft·lbf)13.INSTALL CHECK BALL BODY AND SPRING14.(a)INSTALL VALVE BODYAlign the groove of the manual valve to pin of the lever.SpringCheck Ball BodyD09391PinD009132005 LEXUS IS300 (RM1140U)Author :Date :1636
AT-15AUTOMATIC 21.22.-VALVE BODY ASSEMBLYInstall the 20 bolts.Torque: 10 N·m (100 kgf·cm, 7 ft·lbf)Bolt length:Bolt A: 23 mm (0.91 in.)Bolt B: 28 mm (1.10 in.)Bolt C: 36 mm (1.42 in.)Bolt D: 55 mm (2.17 in.)INSTALL SOLENOID WIRING WITH ATF TEMPERATURE SENSOR (See page AT-9 )INSTALL OIL STRAINER (See page AT-9 )INSTALL OIL PAN (See page AT-9 )INSTALL DRAIN PLUG WITH NEW GASKETTorque: 20 N·m (205 kgf·cm, 15 ft·lbf)FILL FLUID AND CHECK FLUID (See page DI-338 )INSTALL NO. 1 REAR FLOOR BOARDINSTALL LH FRONT FLOOR CENTER COVERINSTALL NO. 1 AND NO. 2 ENGINE UNDER COVERS2005 LEXUS IS300 (RM1140U)Author :Date :1637
AT-16AUTOMATIC TRANSMISSION-PARKING LOCK PAWLPARKING LOCK PAWLAT0HL-02ON-VEHICLE REPAIR1.2.3.4.REMOVE NO. 1 AND NO. 2 ENGINE UNDER COVERSREMOVE LH FRONT FLOOR CENTER COVERREMOVE NO. 1 REAR FLOOR BOARDREMOVE VALVE BODY (See page AT-13 )5.REMOVE PARKING LOCK PAWL BRACKETRemove the 3 bolts and parking lock pawl bracket.D093956.D09392REMOVE SPRING FROM PARKING LOCK PAWLSHAFT7.REMOVE PARKING LOCK PAWL SHAFT AND PARKING LOCK PAWL8.INSTALL PARKING LOCK PAWL AND PARKING LOCKPAWL SHAFT9.INSTALL SPRING TO PARKING LOCK PAWL SHAFT10. INSTALL PARKING LOCK PAWL BRACKETInstall the parking lock pawl bracket with the 3 bolts.Torque: 7.4 N·m (75 kgf·cm, 65 in.·lbf)HINT: Push the lock rod fully forward. Check that the parking lock pawl operates smoothly.11. INSTALL VALVE BODY (See page AT-13 )12. INSTALL NO. 1 REAR FLOOR BOARD13. INSTALL LH FRONT FLOOR CENTER COVER14. INSTALL NO. 1 AND NO. 2 ENGINE UNDER COVERS2005 LEXUS IS300 (RM1140U)Author :Date :1638
AT-17AUTOMATIC TRANSMISSION-SHIFT LOCK SYSTEMSHIFT LOCK SYSTEMAT0HM-02LOCATIONStop Light SwitchKey Interlock SolenoidShift Lock Release ButtonShift Lock Control ECUShift Lock Control SwitchShift Lock SolenoidD093932005 LEXUS IS300 (RM1140U)Author :Date :1639
AT-18AUTOMATIC TRANSMISSION-SHIFT LOCK SYSTEMAT0HN-02Connector BACCIGConnector AP1STPKLS EP2PSLS-INSPECTION1.INSPECT SHIFT LOCK CONTROL ECUUsing a voltmeter, measure the voltage at each terminal.HINT:Do not disconnect the shift lock control ECU connector.SLS D04834TerminalMeasuring conditionB4 - B9 (ACC - E)B5 - B9 (IG - E)Voltage (V)Ignition switch ACC10 - 14Ignition switch ON10 - 14B8 - B9 (KLS - E)4. Ignition switch ACC and P position5. Ignition switch ACC and except P position6. Ignition switch ACC and except P position (After approx. 1 second)B10 - B9 (STP - E)Depressing brake pedal10 - 141.2.3.4.5.08 - 156 - 116 - 110A5 - A4 (SLS - SLS- )07.5 - 11.56-9Ignition switch ON and P positionDepress brake pedalDepress brake pedal (After approx. 1 second)Shift between P and N position under conditions aboveShift D position under conditions aboveA3 - A2 (P1 - P)1. Ignition switch ON, P position and depress brake pedal2. Shift except P position under condition above012A1 - A2 (P2 - P)1. Ignition switch ON, P position and depress brake pedal2. Shift except P position under conditions above1202.(a)(b)SLS-SLS D05063INSPECT SHIFT LOCK SOLENOIDDisconnect the solenoid connector.Using an ohmmeter, measure resistance between terminals.If resistance value is not as specified, replace the solenoid.(c) Check the solenoid operating sound when connecting thebattery positive terminal to 5 (SLS ) and battery negativeterminal to 4 (SLS- ).If the solenoid does not operate, replace the solenoid.3.(a)(b)43KLS KLSD05064INSPECT KEY INTERLOCK SOLENOIDDisconnect the solenoid connector.Using an ohmmeter, measure resistance between terminals.If resistance valve is not as specified, replace the solenoid.(c) Check the solenoid operating sound when connecting thebattery positive terminal to 4 (KLS ) and battery negativeterminal to 3 (KLS- ).If the solenoid does not operate, replace the solenoid.2005 LEXUS IS300 (RM1140U)Author :Date :1640
AT-19AUTOMATIC TRANSMISSION4.(a)(b)PP1P2D05065-SHIFT LOCK SYSTEMINSPECT SHIFT LOCK CONTROL SWITCHDisconnect the shift lock control switch.Inspect that continuity exists between each terminal.Shift positionTerminal condition toterminal numberSpecified valueP position (Release buttonis not pushed)P - P1ContinuityP position (Release buttonis pushed)P - P1P - P2ContinuityExcept P positionP - P2Continuity2005 LEXUS IS300 (RM1140U)Author :Date :1641
AT-20AUTOMATIC TRANSMISSION-FLOOR SHIFT ASSEMBLYFLOOR SHIFT ASSEMBLYAT0HO-02COMPONENTSBox Bottom MatConsol Upper PanelConsol Box Assembly8.3 (85, 73 in.·lbf)Parking Brake Hole Cover AssemblyFloor Shift Lever AssemblyNo. 1 Floor Shift Gear Shifting RodN·m (kgf·cm, ft·lbf) : Specified torque13 (130, 9)D115032005 LEXUS IS300 (RM1140U)Author :Date :1642
AT-21AUTOMATIC TRANSMISSION-FLOOR SHIFT ASSEMBLYPattern Select SwitchShift Lock Release CoverIndicator Light WirePosition Indicator HousingPosition Indicator Light GuideShift LockRelease ButtonSlide CoverCapBulbE-shift Main Switch(D M Position)Shift Lever KnobNo. 2 Slide Cover Shift Lever NutShift Lever Guide CushionSpringShift Lock Control SwitchShift Lever Sub-assembly4.9 (50, 43 in.·lbf)E-shift Main Switch(2 L Position)Detent ShiftLever PinShift Lock Solenoid LinkPinShift Lever GuideHousingSpringBracketShift Lock SolenoidShift Lever Anti-rattleCushionShift Lock Plate StopperShift Lever Lock Pin Shift Lever Ring Shift LeverNutSpring NutPinCushionControl LeverPlate WasherE-ringShift Lock Control ECUPlate Washer SpacerCollarPlate Washer O-RingSpacerSwivel13 (130, 9)Shaft Lower Control Bush O-Ring SpacerN·m (kgf·cm, ft·lbf) : Specified torque Non-reusable part MP greaseShift Lever PlateShift Lever SealD115042005 LEXUS IS300 (RM1140U)Author :Date :1643
AT-22AUTOMATIC TRANSMISSION-FLOOR SHIFT ASSEMBLYAT0HP-02REMOVAL1.(a)(b)(c)(d)SEPARATE NO. 1 FLOOR SHIFT GEAR SHIFTINGRODShift into the N position.Remove the nut and separate the No. 1 floor shift gearshifting rod from the connecting rod swivel.REMOVE CONSOLE BOX ASSEMBLY(See page BO-139 )Remove the console upper panel.Remove the box bottom mat.Remove the parking brake hole cover assembly.Remove the console box assembly.3.(a)(b)(c)REMOVE FLOOR SHIFT LEVER ASSEMBLYRemove the 4 bolts.Disconnect the 2 connectors.Remove the floor shift lever assembly.(a)(b)2.D11505D115062005 LEXUS IS300 (RM1140U)Author :Date :1644
AT-23AUTOMATIC TRANSMISSION-FLOOR SHIFT )4.5.(a)(b)(c)(d)REMOVE SHIFT LEVER KNOBREMOVE POSITION INDICATOR HOUSINGUsing a small screwdriver, remove the shift lock releasecover from the position indicator housing.Disconnect the pattern select switch connector.Remove the position indicator housing assembly.Remove the pattern select switch from the position indicator housing assembly.REMOVE POSITION INDICATOR LIGHT GUIDEDisconnect the indicator light wire from the position indicator light guide.Remove the position indicator light guide.REMOVE SLIDE COVER AND NO. 2 SLIDE COVERREMOVE SHIFT LEVER GUIDE HOUSINGDisconnect the shift lock control ECU connector and indicator light wire from the shift lever plate.Remove the 2 E-shift main switches and shift lock controlswitch from the shift lever guide housing.Remove the 4 bolts, nuts and shift lever guide housing assembly.Remove the bulb and cap and from the indicator light wire.D115076.DISASSEMBLE SHIFT LEVER GUIDE HOUSING(a) Using a screwdriver, ply and push up 3 shift lever nuts.(b) Using nippers, cut the 3 shift lever nuts off then.HINT:Remove the shift lever lock pin of shift lever nut in the same way.(c) Remove the shift lever guide cushion.(d) Remove the 3 screws, shift lock control ECU and shift locksolenoid.(e) Remove the shift lock control ECU bracket and shift leveranti-rattle cushion from the shift lock control ECU.(f)Disconnect the E-shift main switch connector from theshift lever guide housing.(g) Remove the shift lock release button and spring.D094082005 LEXUS IS300 (RM1140U)Author :Date :1645
AT-24AUTOMATIC TRANSMISSION-FLOOR SHIFT ASSEMBLY(h)Remove the shift lever lock pin, shift lock plate stopperand cushion.7.DISCONNECT SHIFT LOCK CONTROL ECU, SHIFTLOCK SOLEN
2005 lexus is300 (rm1140u) operation. at0he-02 d05052 sst or0005 sst automatic transmission - extension housing oil seal at-3 author: date: 1625 2005 lexus is300 (rm1140u) extension housing oil seal on-vehicle repair 1. remove no. 1 and no. 2 engine under covers 2. remove lh front floor center cover 3. remove no. 1 rear floor board 4. remove exhaust pipe assembly (see page em-100) 5. remove .
ZF Transmission Service Manual 5 2 Transmission System 2.1 Transmission Introduction 2.1.1 General Overview of the Transmission The ZF power gearshift transmission is composed of the hydraulic torque converter and rear-mounted countershaft transmission with multi-sheet friction clutch. The SDLG 938L、
3/5/2019 Automatic Transmission - 6-Speed PowerShift Transmission - DPS6/6DCT250 - Clutch and Damper Unit - Removal and Installation 2012 Speed PowerShift Transmission - DPS6/6DCT250, Installation).
2.0L 115 hp, 6-speed automatic transmission with Tiptronic Maximum torque: 125 lb-ft at 4,000 rpm 1.8 TSI 170 hp, 5-speed manual transmission 1.8 TSI 170 hp, 6-speed automatic transmission with Tiptronic Maximum torque: 184 lb-ft at 1,500-4,750 rpm 2.0 TDI 150 hp, 6-speed manual transmission 2.0 TDI 150 hp, 6-speed automatic DSG with Tiptronic
Transmission Automatic 6-speed DSG Manual 6-speed Automatic 6-speed DSG Automatic 7-speed DSG Automatic 7-speed DSG Manual 6-speed Automatic 7-speed DSG Automatic 7-speed DSG WEIGHT Kerb weight - in standard version with a 75kg driver (kg) 1,561 (1,604) 1,615 (1,658) 1,630 (1,673) 1,695 (1,738) 1,667 (1,710) 1,705 (1,748) 1,740 (1,783) 1,752 .
Electricity Transmission . discussion of state transmission policies. Because so many of these policies relate to permitting and siting transmission facilities, much of the policy discussion focuses on transmission siting. A Quick History . Growth of the Transmission System . The 19. th. century inventors who first began to harness electricity .
2007 TRANSMISSION AB60F Automatic Transaxle - Tundra . 2007 TRANSMISSION AB60F Automatic Transaxle - Tundra AT-Service-RF . MANUAL SHIFTING TEST a. Refer to the MANUAL SHIFTING TEST . NG: Go TO STEP 16 Result Proceed to DTC is not output A DTC is output B 2007 Toyota Tundra
AUTOMATIC SLIDING SYSTEM Automatic sliding doors have flat panels with a number of configurations, which slide horizontally and linearly. As shown in Fig.1, the automatic sliding system consists of the sensing mechanism, main controller circuit and motor. The circuit module is used as the key controller for automatic door sliding system.
5.3.3.5 Dana Pensiun Lembaga Keuangan 80 5.3.3.6 Pegadaian 84 5.3.3.7 Asuransi 85 BAB VI PASAR UANG DAN PASAR MODAL 93 6.1 Instrumen-instrumen Pasar Uang 95 1. Treasury Bills (T-Bills) 95 2. Bankers Acceptance 96 3. Bill of Exchange 98 4. Repurchase Agreement 99 5. CPPP (Commercial Paper Promissory Note) 101 vi
