Food Conveyor Belting - Gates Corporation
Food Conveyor BeltingGM FCB 2018 US Version 9/18GatesMectrol.com Food Belts 1
Gates MectrolDesign Leadership and ServiceReflecting 25 years of synchronous timing belt experience, theGates Mectrol food belt product line represents the “next generation” of food processing belting. Features such as embeddedtension cords to eliminate stretch, a robust pin splice design forquick belt fastening and removal, a coextrusion process to reducesurface “sinks” and a “split tooth” weld for greater weld strengthare all examples of Gates Mectrol’s design leadership.While the products are evolving quickly, one constant through allthis is Gates Mectrol’s position as the service leader. The shortlead times and ability to expedite orders same day sets GatesMectrol apart.2 Gates Mectrol Food Belts
Reinforced Urethane Food BeltingAdvantages Easy to clean- Reduces risk of microbial contamination- 43% less surface area to clean than plastic modular belting- Appropriate for Clean In Place (CIP) cleaning protocol These blue belts are “green”- Significant cleaning water savings, cleaning labor savings and wastewater reduction 600 gallons in annual water savings for every foot of 24” wide plasticmodular belting replaced- Half the cleaning time of plastic modular belting- 30% lighter than plastic modular belting Less energy used Easier on motor bearings Belt construction- Kevlar tension members stabilize belt properties under all lengths, loads andtemperatures No retensioning, due to stretch, needed Innovative belt joining technology- Robust, “split tooth” joining process eliminates service callbacksEasily Cleaned In PlaceGatesMectrol.com Food Belts 3
Gates Mectrol Food BeltsTABLE OF CONTENTSPreface . 2Advantages of Reinforced Urethane Food Belting . 3Food Belt Product Line. 8Positive Drive and Frictional Drive Conveyor BeltingPosiClean Belting and Sprockets . 9CenterClean Belting and Sprockets . 13FlatClean Belting and Pulleys . 16Dewatering Belt. 19FABRICATIONSidewalls . 22Straight Cleats . 23Scoop Cleats. 24Guseted Cleats. 25V-Guides . 26Fabrication Accessories . 27JOININGSplicing . 28Splicing Accessories . 29Mechanical Fastening . 30CONVEYOR DESIGN GUIDELINESDrive Configuration. 36Head Drive Configuration . 36Tail Drive Configuration . 36Center Drive Configuration . 37Drum Motor (Motorized Pulley) . 38Basic Straight Line Conveyor . 38Belt Guide and Tracking. 39Carryway Support . 40Returnway Support. 41Snub Roller . 42Tensioning Device (Tensioner/Take Up) . 43Straight Line Conveyor with Cleats . 44Carryway Support. 44Returnway Support. 444 Gates Mectrol Food Belts
Gates Mectrol Food BeltsTABLE OF CONTENTS (continued)CONVEYOR DESIGN GUIDELINES (continued)Straight Line Conveyor with Corrugated Sidewalls . 46Corrugated Sidewall Geometries . 46Minimum Sprocket/Pulley Diameter. 46Carryway Support. 46Returnway Support. 46Z-Conveyor . 48Carryway Transition. 49Returnway Transition. 50Carryway Support. 50Returnway Support. 50Drive Sprockets . 51Tail Sprockets. 51Conveyor Sidewalls . 51Reciprocating Conveyor (Telescoping, Shuttle or Retractable) . 51Belt Tracking. 52Back Bend Roller. 52Sprockets. 52Tension. 52Troughed Conveyors . 52Carryway Support. 53Transition Length. 54Belt Width. 54Returnway Support. 54Pulleys . 55SUPPORT MATERIALInstallation Checklist . 58Certificates . 60Belt Sanitation. 62Recommended Sanitation Procedures. 62Common Sanitation Chemicals. 62Chemical Resistance Chart. 63Safety Policy . 70Contacts . 72Kevlar is a registered trademark of E.I. du Pont de Nemours and CompanyFlexco , Clipper , Alligator , and Ready Set are registered trademarks of Flexible Steel Lacing CompanyGatesMectrol.com Food Belts 5
6 Gates Mectrol Food Belts
Product IndexFood Belt ProductsOverview. 8Positive Drive and Frictional Drive Conveyor BeltingPosiClean Belting and Sprockets. 9CenterClean Belting and Sprockets . 13FlatClean Belting and Pulleys . 16Dewatering Belt. 19FABRICATIONStraight Cleats . 21Sidewalls. 23Scoop Cleats . 24Gusseted Cleats. 25V-Guides . 26Fabrication Accessories . 27JOININGSplicing . 28Splicing Accessories . 29Mechanical Fastening . 30GatesMectrol.com Food Belts 7
Food Belt Product LineGates Mectrol Food cONVEYOR BeltingPosiClean Food Conveyor Belting 2” pitch (PC20) for standard to high loads 1” pitch (PC10) for improved transfer betweenconveyors Special construction belts for cold temperatureand heavier loads Direct replacement of most 1” and 2” pitchplastic modular belt Full width drive tooth distributes torque overentire belt width making this belt appropriatefor high load applications Widths up to 48”CenterClean Food Conveyor Belting Drive teeth only in the center three inchesof the belt (or two tracks of teeth for beltwidths greater than 30”) Pitch length of 1.575” (40 mm) Appropriate for troughing applications Widths up to �� .138” .236”PC10FC128 Gates Mectrol Food Belts.226”PC20PC201.02”FlatClean Food Conveyor Belting Appropriate for troughing applications Widths up to 60”.301”FC12 - .125“
PosiClean BeltingPosiClean Belting is an easy to clean, positive drive replacement for plastic modular beltin the food processing industry. PosiClean belting has sealed Kevlar tension members to limitbelt stretch and a tooth construction that extends across the full belt width for better torquedistribution.Application Characteristics Replacement for plastic modular belt- Easier cleaning- No hinges or pins to break and possiblycontaminate product- Quieter operation- 30% less weight Less labor and cleaning water than plasticmodular PC20PC20.354”.354” Formulated for wash down environments Full width drive tooth distributes torque overentire belt width making this belt appropriatefor high load applicationsFeatures Direct replacement of most 1" and 2" pitch plasticmodular belt Smooth surface allows cleaning to microbiologicallevel and clean-in-place processPC10PC101.02”.169” .138” .248”.236” Sealed edges and tension members preventingress of microbes Kevlar tension members provide high strength,low stretch- Stabilize belt under all lengths, loads andtemperatures1.02”.169” .138” .236”PC10 Tough polyurethane construction- Water and chemical resistant- Meets FDA material requirements for wet foodcontact Welded endless or spliced with stainless steel orplastic lacing USDA accepted for meat, poultry and dairyprocessing equipmentGatesMectrol.com Food Belts 9
PosiClean BeltingPosiClean Belting SpecificationsPC20 PC10Belt OptionsStandard Hi TorqueCold Temp StandardDesignator KV-FDACords/Inch 2HDK-FDAKV-R6KV-FDA422Pitch (nominal)1.97” (50 mm)1.97” (50 mm)1.97” (50 mm)1.02” (26 mm)Hardness - Shore A95958595Surface TexturesSmooth & Inverted PyramidSmooth & Inverted PyramidSpecific Belt Weight (lbs/ft/in)0.0890.0890.0890.063Specific Belt Stiffness (lbs/inch)74001180074007400Min. Sprocket Dia. Service Temp Above 25 F 3.76” (95.5 mm)3.76” (95.5 mm)3.76” (95.5 mm)2.0” (50.8 mm)Min. Sprocket Dia. Service Temp Below 25 F 6.27” (159.3 mm)6.27” (159.3 mm)6.27” (159.3 mm)3.25” (82.6 mm)6” (152.4 mm)6” (152.4 mm)6” (152.4 mm)3.5” (88.9 mm)Min. Back Bend Dia. Below 25 F 10” (254.0 mm)10” (254.0 mm)10” (254.0 mm)5” (127.0 mm)Service Temperature Range 15 to 160 F 15 to 160 F-10 to 158 F 15 to 160 FMin. Back Bend Dia. Above 25 F(-9 to 71 C)(-9 to 71 C)(-23 to 70 C)(-9 to 71 C)Ultimate Belt Strength (lbs/in of width)265502265294Coefficient of Friction (dynamic/static)Urethane vs. UHMW - Dry0.20 / 0.300.20 / 0.300.54 / 0.690.20 / 0.30Urethane vs. UHMW - Wet0.35 / 0.580.35 / 0.58-0.35 / 0.58Urethane vs. Stainless Steel - Dry0.38 / 0.410.38 / 0.410.64 / 0.680.38 / 0.41Urethane vs. Stainless Steel - Wet0.40 / 0.570.40 / 0.57-0.40 / 0.57Coefficient of Thermal Expansion (in/in/ F)1.09 x 10-41.09 x 10-41.09 x 10-41.09 x 10-4(mm/mm/ C)1.96 x 10-41.96 x 10-41.96 x 10-41.96 x 10-4PosiBluePosiBluePosiBlue, PosiWhite5”/48”5”/48”4”/48”(127/1219 mm)(127/1219 mm)(102/1219 mm)200’ (61 m)200’ (61 m)200’ (61 m)Color PosiBlue, PosiWhiteMin. and Max. Width5”/48”(127/1219 mm)Std. Roll Length200’ (61 m)PosiClean Series Part Number NomenclaturePC203000 /2400Width: 24.00 “Length: 300.0”(PC 10 must be in increments of 1.02”, PC20 must be in increments of 1.97”)Pitch: PC10, PC20(“HDK” for PC20 4 cord per inch, “R6” for Cold Temp.)10 Gates Mectrol Food Belts
PosiClean BeltingMax. Allowable Tension (lbs per inch width)1 based on Splicing OptionPC20 PC10Joining Options Standard Hi TorquePlaten Weld - 30 mm x 70 mm Finger50644635Platen Weld - Split Tooth40403731Butt Weld31313031PosiLace (up to 42” wide)262626N/AFlexco UX1SS Clipper Wire Hooks31413731Flexco APF150 Alligator Plastic Rivet252523N/AFlexco APF100 Alligator Plastic RivetN/AN/AN/A25Flexco RS125 Alligator Ready Set Staple262623N/AFlexco RS62 Alligator Ready Set StapleN/AN/AN/A26 1Cold Temp Standard Max allowable set as the lower of 25% yield strength or 2% stretch of weld or splicePosiClean Slit Width TolerancesUp To and Including 15.75”15.76” to 23.62” 23.63” or more 0.00 to -.125” 0.00 to -.1875” 0.00 to -.25”PosiClean Belting Master Rollstock Width Tolerances18”36” /- 0.0625” 0.125” / -0.375”PosiClean Belt Length TolerancesPC10Cut 1.0” / -.0”Rollstock /- 1%PC20Cut 2.0” / -.0”Rollstock /- 1%GatesMectrol.com Food Belts 11
PosiClean SprocketsPosiClean Sprocket SpecificationsPC20 PC10Tooth Count6810121668101220Outside Diameterinch3.74.96.27.510.0 63Widthinch1.31.31.31.31.31111 1(Nominal)mm32.032.032.032.032.0 25.425.425.425.425.4square, in1.51.51.51.51.5 N/AN/A1.51.51.511111 11N/AN/AN/Asquare, mm4040404040 N/AN/A404040round, mm3030303030 3030N/AN/AN/AIn Stock (Square Bore Only) (F Flange, NF No Flange)F, NFF, NFF, NFF, NFF, NFNFNFNF.32.68.57.75.17.30.99Bore SizeImperialround, inMetricWeight(lbs)3.1 .06.12* Imperial keyway sizes on round bores conform to ANSI standard B17.1 - 1967 (R1989); metric keywaysizes conform to BS 4235: Part 1: 1972 (1986)For pulleys with flanges, add .196” to outside diameter to getflange diameter.Notes:- Injection molded pulleys - acetal, machined pulleys - UHMW-PE- Sprockets must be locked into position on the shaft.- PC10 belting can run on some competitor’s plastic modular beltingwith 8, 10, 12 and 20 tooth sprockets.- PC20 belting can run on some competitor’s plastic modular beltingwith 8, 10 and 12 tooth sprockets.PosiClean Sprocket & Support Guidelines (PC20 and PC10)Belt Width6”(152 mm)Min. No. SprocketsMax. 5” (127 mm)spacing center to center39”12”15”18”21”(229 mm) (305 mm) (381 mm) (457 mm) (533 mm)24”27”(610 mm) (686 mm)30”36”(762 mm)(914 mm)40”45”(1016 mm) (1143 mm)48”(1219 mm)3445667789101134spacing center to center5678910111315161734455667899No. of Sprockets for max.allow. tension Max. 3” (76 mm)Min. No. Carryway Supports6” (152 mm)spacing center to center12 Gates Mectrol Food Belts23
CenterClean BeltingCenterClean 40 belting has drive teeth only in the center three inches of the belt and a pitchlength of 1.575” (40 mm). The center position of teeth makes this belt appropriate for self-tracking and troughing applications as well as lighter load general processing.1.575”[40 mm]Application Characteristics Formulated for wash down environments Troughing conveyor Self-centering designFeatures Smooth surface allows cleaning to microbiologicallevel and clean-in-place process.125”[3.2 mm].300”[7.6 mm]CC40 Sealed edges and tension members prevent ingress ofmicrobes Kevlar tension members provide high strength, lowstretch- Stabilize belt under all lengths, loads and temperatures Tough polyurethane construction- Water and chemical resistant- Meets FDA material requirements for wet foodcontact Welded endless or spliced with stainless steel or plastic lacing48.0”[1219 mm]23.88”[606.6 mm]CC40 Tooth Placement USDA accepted for meat, poultry and dairy processingequipmentCenterClean belts are constructed withflexible urethane and sealed Kevlar tension members. This construction allowsCenterClean belts to be troughed or runon small diameter pulleys with minimalbelt stretch.GatesMectrol.com Food Belts 13
CenterClean BeltingCenterClean Belting SpecificationsBelt OptionsCC40Average Cords/inchPitch (nominal)Hardness - Shore A21.575” (40 mm)95Smooth & Inverted Pyramid0.07874004.9” (124 mm)5.9” (150 mm)6” (152 mm)10” (254 mm)15 to 160 F(-9 to 71 C)Surface TexturesSpecific Belt Weight (lbs/ft/in)Specific Belt Stiffness (lbs/inch)Min. Sprocket Dia. service temperature above 25 FMin. Sprocket Dia. service temperature below 25 FMin. Back Bend Dia. above 25 FMin. Back Bend Dia. below 25 FService Temperature RangeCoefficient of Friction (dynamic/static)Urethane vs. UHMW - DryUrethane vs. UHMW - WetUrethane vs. Stainless Steel - DryUrethane vs. Stainless Steel - WetCoefficient of Thermal Expansion (in/in/ F)(mm/mm/ C)ColorMin. and Max. WidthStd. Roll Length0.20 / 0.300.35 / 0.580.38 / 0.410.40 / 0.571.09 x 10-41.96 x 10-4PosiBlue, PosiWhite6”/ 48” (152 / 1219 mm)200’ (61 m)CenterClean Maximum Allowable Belt Tension (lbs) based on Splice Option and Belt WidthWidth RangesSingle TrackJoining OptionsDual Track6”- 9” 9”- 12” 12”- 17” 17” - 36” 30” - 39” 39” - 42” 42” - 60”Butt Weld (between the 498N/AUX1SS Mechanical239275317344724766793APF150 Mechanical139160184199419443458RS125 Mechanical29033438541787892996114 Gates Mectrol Food Belts
CenterClean BeltingCenterClean Series Part Number NomenclatureCC402998 /2400Width: 24.00”Length: 299.8” (Must be in increments of 1.575”)Pitch:CenterClean Tooth Center TolerancesCenterClean Slit Width TolerancesUp To and Including 15.75”15.76” or more /- 0.0625” /- 0.125” /- 0.125”CenterClean Belting Master Rollstock Width TolerancesCenterClean Belt Length Tolerances 0.125” / -0.375”CenterClean Carryway Support GuidelinesCut 1.5” / -.0”Rollstock /- 1%BDistance Between Parallel Wear Strips Guiding Belt Teeth, Dim. A3.15”Distance Between Parallel Wear Strips Not Guiding Belt Teeth, Dim. B4” - 6”ABCenterClean Sprocket SpecificationsCC40Number of Teeth 1011121315161720Nom. Outside DiameterNominal WidthImperial Square Bore - ialUHMW-PENotes: CC40 belts run on most 40 mm pitch sprockets.Sprockets must be locked into position on the shaft.GatesMectrol.com Food Belts 15
FlatClean BeltingFlatClean is a USDA approved, polyurethane flat belt reinforced with Kevlar tensilemembers. The combination of a non-fraying polyurethane jacket material with sealedtensile members minimizes belt stretch, reduces retensioning and extends belt life.Application Characteristics Standard to high loads, particularly wellsuited for cleated belts Troughing Wash down environmentsfeatures Sealed edges and tension members preventingress of microbes Kevlar tension members provide highstrength, low stretch and are cut andabrasion resistant- Eliminate need to retension conveyor- Stabilize belt under all lengths, loads andtemperatures Smooth surface and non-fraying edges allowcleaning to a microbiological level Welded endless or spliced with stainlesssteel lacing Tough polyurethane construction- Water and chemical resistant- Meets FDA material requirements for wetfood contact FC12 is an all-purpose flat belt appropriatefor most applications, 2” minimum pulleydiameter FC9 is a specialty belt for lighter loads. It hasa 1” minimum pulley diameter. USDA accepted for meat, poultry and dairyprocessing equipment16 Gates Mectrol Food BeltsFC12 - .125“
FlatClean BeltingFlatClean Belting specificationsBelt OptionsDesignatorSurface FinishTopRunning SideFC12FC9IPRFC12 FC12IPSmoothThicknessInverted PyramidSmoothSmoothSmoothInverted Pyramid0.125” / (3.0 mm)0.125” / (3.0 mm)0.125” / (3.0 mm)Hardness, Shore ATop (Medium Blue)95 9590Running Side (PosiBlue)95 9595Cords/inch2.0 2.0Tensile Force for 1% Elongation (k1 Relaxed) per Unit of Width2.55.4 N/mm5.4 N/mm4.5 N/mmUltimate Belt Strength (lbs/inch width)265265203Specific Belt Weight (lbs/ft/in)0.0650.0650.048Specific Belt Stiffness (lbs/inch)74007400Min. Pulley Dia. Service Temperature Above 25 F2.0” (51 mm)2.0” (51 mm)1.0” (26 mm)4410Min. Pulley Dia. Service Temperature Below 25 F3.0” (76 mm)3.0” (76 mm)2.0” (51 mm)Min. Back Bend Dia. Above 25 F2.0” (51 mm)2.0” (51 mm)2.0” (51 mm)Min. Back Bend Dia. Below 25 F3.0” (76 mm)3.0” (76 mm)3.0” (76 mm)Service Temperature Range 15 to 160 F 15 to 160 F 15 to 160 F(-9 to 71 C)(-9 to 71 C)(-9 to 71 C)Coefficient of Friction (Dynamic/Static)TPU vs. UHMWTPU vs. SteelTPU vs. UHMWTPU vs. 38/0.41Smooth0.89/1.21WetTop0.40/0.57 0.40/0.57Smooth0.75/1.20DryRunning SideN/A0.11/0.21Inverted Pyramid0.19/0.25WetRunning SideN/A0.14/0.23Inverted Pyramid0.24/0.27DryRunning SideN/A0.22/0.27Inverted Pyramid0.40/0.35WetRunning SideN/A0.23/0.28Inverted Pyramid0.42/0.36Coefficient of Thermal Expansionin/in/ F1.09 x 10-41.09 x 10-41.09 x 10-4[mm/mm/ C]1.96 x 10-41.96 x 10-41.96 x 10-4ColorTopPosiBlue, PosiWhite PosiBlue, PosiWhiteMedium BlueRunning SideMin. and Max. Width4” / 60”4” / 60”(102 / 1524 mm)(102 / 1524 mm)Std. Roll Length300’ (91 m)300’ (91 m)PosiBlue4” / 48”(102 / 1219 mm)300’ (91 m)FlatClean Series Part Number NomenclatureFC12IP 3000 /2400Width: 24.00 “Length: 300.0”Designator: FC9 (“IPR” for Inverted Pyramid Running Side)FC12 (“IP” for Inverted Pyramid One Side)GatesMectrol.com Food Belts 17
FlatClean BeltingFlatClean Belting Max. Allowable Tension (lbs per inch width)1Joining OptionsFC12FC12IPFC9IPR484830NR*NR*N/A595933Flexco APF100 Alligator Plastic RivetN/AN/A27Flexco APF150 Alligator Plastic Rivet3434N/AFlexco RS62 Alligator Ready Set StapleN/AN/A31Flexco RS125 Alligator Ready Set Staple5151N/APlaten Weld - 20 mm x 70 mm FingerPosiLace (up to 42” wide)Flexco UX1SS Clipper Wire HooksMax allowable set as the lower of 25% yield strength or 2% stretch of weld or splice* Contact Applications for specific requests.1FlatClean Slit Width TolerancesUp To and Including 15.75”15.76” or more /- 0.0625” /- 0.125”FlatClean Belting Master Rollstock Width Tolerances48” 0.125” / -0.375”FlatClean Belt Length TolerancesCut 1.0” / -.0”Rollstock /- 1%18 Gates Mectrol Food Belts
Dewatering BeltDewatering Belt serves common produce processing applicationssuch as fruits and vegetables. Embedded Kevlar cord prevents belt stretch Longer life than mesh belting USDA approved and EU compliant Two belt constructionsBelting SpecificationsPC20Belt OptionsModifiedDesignatorKV-FDACords/Inch1Pitch (nominal)1.97” (50 mm)Hardness - Shore A95Surface Textures - Smooth & Inverted PyramidSpecific Belt Weight (lbs/ft/in)0.089Specific Belt Stiffness (lbs/inch)3700Min. Sprocket Dia. Service Temp Above 25 F3.76” (95.5 mm)Min. Sprocket Dia. Service Temp Below 25 F6.27” (159.3 mm)Min. Back Bend Dia. Above 25 F6” (152.4 mm)Min. Back Bend Dia. Below 25 F10” (254.0 mm)Service Temperature Range2.5” Solid Belt Edge- for Belt IntegrityOpening3/16” Dia. 11% Max.Widths Available 14” to 18” and 32” to 36”-4 to 158 F(-20 to 70 C)Ultimate Belt Strength (lbs/in of width)132Coefficient of Friction (dynamic/static)Urethane vs. UHMW - Dry0.33 / 0.42Urethane vs. UHMW - Wet0.35 / 0.58Urethane vs. Stainless Steel - Dry0.52 / 0.57Urethane vs. Stainless Steel - Wet0.40 / 0.57Coefficient of Thermal Expansion (in/in/ F)(mm/mm/ C)ColorStd. Roll Stock Length1.09 x 10-41.96 x 10-4PosiBlue200’ (61 m)Holes Punched to Edge- for Maximum DrainageOpening3/16” Dia. 15%1/4” Dia.19%Widths Available 5” to 36” in 1”Max. Allowable Tension (lbs per inch width)1 based on Splicing OptionJoining Options1Butt Weld - Split Tooth40PosiLace 26Max allowable set as the lower of 25% yield strength or 2% stretch of weld or spliceGatesMectrol.com Food Belts 19
Dewatering BeltPosiClean Sprocket SpecificationsPC20Tooth Count68101216Outside 032.032.0square, in1.51.51.51.51.5round, in11111square, mm4040404040round, mm3030303030F, NFF, NFF, NF.32.68.57Bore SizeImperialMetricIn Stock(Square Bore Only)(F Flange, NF No Flange)Weight(lbs)F, NF F, NF.753.1* Imperial keyway sizes on round bores conform to ANSI standard B17.1 - 1967 (R1989);metric keyway sizes conform to BS 4235: Part 1: 1972 (1986)For pulleys with flanges, add .196” to outside diameterto get flange diameter.Notes:- Injection molded pulleys - acetal, machined pulleys - UHMW-PE- Sprockets must be locked into position on the shaft.- PC20 belting can run on some competitor’s plastic modularbelting with 8, 10 and 12 tooth sprockets.PosiClean Sprocket & Support GuidelinesBelt WidthMin. No. SprocketsMax. 5” (127 mm)spacing center to (229 mm)(305 mm)(381 mm)(457 mm)(533 mm)(610 mm)(686 mm)(762 mm)(914 mm)34456677867891011134455667No. of Sprockets for max.allow. tension Max. 3” (76 mm)45spacing center to centerMin. No. Carryway Supports6” (152 mm)spacing center to center20 Gates Mectrol Food Belts33
GatesMectrol.com Food Belts 21
FabricationSidewallsCorrugated sidewalls can be added to any Gates Mectrol Food Grade Belt to contain product.Sidewall SpecificationsSidewall DimensionsHeight "A”Length (Width Across Belt) “B”ThicknessDurometerColorSurface TexturesSidewall TolerancesMinimum Belt LengthMaximum Belt Length* Minimum Belt WidthMaximum Belt WidthMinimum Distance:Belt Edge to Sidewall “C”Minimum Distance:Cleat and Sidewall “D”Minimum Sprocket DiameterType, Which Ever is GreaterMinimum Back Bend DiameterSidewall Loop AlignmentSidewall End WeldBelt Sections Allowed1.38 - 4.33” (35 - 110 mm)1.57“ (40 mm)0.079“ (2.0 mm) Nominal85 Shore APosiBlue, PosiWhiteSmooth and Inverted PyramidHeight Tolerance 0.25” ( 6.4 mm)Length Tolerance 0.20” ( 5 mm)Thickness Tolerance 0.015” (0.4 mm)80” (2.0 m)140’ (42.7 m)8” (200 mm)48” (1219 mm)0.25” 0.075” (6 mm 2 mm)Cleats/Scoop Cleats 4” and Less:0.375” /-0.075” (9.5 mm /- 2 mmCleats/Scoop Cleats Greater than 4”:0.60” /- 0.075” (15.2 mm /- 2 mm)2.5x Sidewall Height or Minimum Diameter Recommendation for Belt
Max. allowable Tension (lbs per inch width)1 based on splicing Option 1 Max allowable set as the lower of 25% yield strength or 2% stretch of weld or splice 18” 36” /- 0.0625” 0.125” / -0.375” posiClean Belting Master rollstock Width Tolerances Up To
To place an order please use the Conveyor Request Form (page 37) or visit the online Belt Conveyor Confi guration Tool at www.robotunits.com Description Frame Width F max. 3) Belt Conveyor 40 40 mm 300 N Belt Conveyor 40 80 mm 700 N Belt Conveyor 40 120 mm 1100 N Belt Conveyor 40 160 mm 1500 N Belt Conveyor 40 200 mm 1900 N Belt Conveyor 40 .
Many types of gates have been used in a variety of reservoir spillway structures. The most common spillway gates are the radial (Tainter) gates, wheel-mounted type gates, Stoney gates,drum gates, crest gates, Obermeyer crest gates, or the one time - use fuse gates [USSD 2002]. In general,
PVC conveyor belt roll, 150m x 1200mm Qty: 10 1060 Twin-roll steel conveyor structure 1061 Assorted small and medium conveyor rollers 1062 Steel piping . Goodyear pylon conveyor belting: Qty: 2 1092 Goodyear pylon 4ply conveyor 150m x 600mm 1093 Goodyear plylon conveyor
systems, Conveyor System KF-P 2040.86 is ideally suited for continuous duty applications in multi shift environments. The conveyor features T-slots to which accessories including stands, rails, hoppers or chutes can easily be mounted. Belting Options Modular Plastic Belting: Ideal for transport of plastic, blow molded parts or small metal .
Hygienic design of food conveyor belts 6 Conveyor belts a vital part of the process line Hygienic design of machinery, equipment and conveyor belts is the basis for safe food production. Conveyor belts are not an isolated item; they have supports, rollers, fixings to mention a few.
Separate conveyor belt. Remove front and back halves of the conveyor via 6 screws. Separate front and rear conveyor sections. Insert the 10" conveyor extension noting the position of the inner and outer joiner plates. Attach extension to front and rear conveyor section with screws provided. Splice the conveyor belt extension piece.
Plate Conveyor Belt Plate conveyor belt can be divided into three types: chain, perforated and convex plate conveyor belt. Chain plate conveyor belt can be made into L-shaped, U-shaped or rectangular according to the requirement of space. The holes on the surface of perforated plate conveyor belt with good heat dissipation function.
Netzwerk – Arbeitsbuch B1.2 Lösungsschlüssel Netzwerk B1 Lösungsschlüssel zum Arbeitsbuch Seite 2 3. Bevor er in die Stadt fährt, schreibt er Mails. 4. Bis sie ihre Freunde besuchen kann, langweilt sie sich. 5. Während sie Deutsch lernen, sehen sie fern. 6. Nachdem wir Sport gemacht haben, sehen wir fern. 7. Während er krank war, hat .
