Wm 700 S,P (Rev 6) - Multiquip Inc
PARTS AND OPERATION MANUALPLASTER / MORTAR MIXERS COPYRIGHT 2001, MULTIQUIP INC.WM-700SWM-700PRevision #7 (06/26/01)MULTIQUIP INC.PARTS DEPARTMENT:18910 WILMINGTON AVE.800-427-1244CARSON, CALIFORNIA 90746 FAX: 800-672-7877SERVICE DEPARTMENT/TECHNICAL : 310-537-3927FAX: 310-631-5032E-mail:mq@multiquip.com www:multiquip.comAtlanta Boise Dallas Houston NewarkMontreal, Canada Manchester, UKRio De Janiero, Brazil Guadalajara, Mexico
PAGE 2 — WHITEMAN WM-700S, 700P — PARTS & OPERATION MANUAL — REV. #7 (06/21/01)
HERE'S HOW TO GET HELPPLEASE HAVE THE MODEL AND SERIAL NUMBERON-HAND WHEN CALLINGPARTS DEPARTMENT800-427-1244 or 310-537-3700FAX: 800-672-7877 or 310-637-3284SERVICE DEPARTMENT/TECHNICAL ASSISTANCE800-478-1244 or 310-537-3700FAX: 310- 537-4259WARRANTY DEPARTMENT888-661-4279, or 310-661-4279FAX: 310- 537-1173MAIN800-421-1244 or 310-537-3700FAX: 310-537-3927WHITEMAN WM-700S, 700P — PARTS & OPERATION MANUAL — REV. #7 (06/26/01) — PAGE 3
TABLE OF CONTENTSHere's how To Get Help . 3Table Of Contents . 4Parts Ordering Procedures . 5Rules for Safe Operation & Safety Decals . 6Warranty . 7WHITEMAN — 700S & 700POperations . 8-10Specifications . 11Explanation Of Codes In Remarks Column . 12Suggested Spare Parts . 13Drum Head & Paddle Shaft Assembly . 14-15Steel Drum (S) . 16-17Polyethylene Drum (P) . 18-19Gas Engines, Pulleys & Cab Assembly . 20-21Electric Motor & Pulleys . 22-23Axle & Wheel Group . 24-25Terms and Conditions Of Sale — Parts . 26PAGE 4 — WHITEMAN WM-700S, 700P — PARTS & OPERATION MANUAL — REV. #7 (06/21/01)
PARTS ORDERING PROCEDURESnnnnnnnDealer account numberDealer name and addressShipping address (if different than billing address)Return fax numberApplicable model numberQuantity, part number and description of each partSpecify preferred method of shipment: UPS GroundUPS Second Day or Third Day*UPS Next Day*Federal Express Priority One (please provide us with your FederalExpress account number)* Airborne Express*Truck or parcel post*Normally shipped the same day the order is received, if prior to 2PM west coast time.Earn Extra Discounts whenyou order by FAX!All parts orders which include complete part numbersand are received by fax qualify for the following extradiscounts:Number ofline items ordered1-9 itemsAdditional Discount3%10 items**5%Get special freight allowanceswhen you order 10 or moreline items via FAX!**nnUPS Ground Service at no charge for freightPS Third Day Service at one-half of actual freight costNo other allowances on freight shipped by any other carrier.**Common nuts, bolts and washers (all items under 1.00 list price)do not count towards the 10 line items.*DISCOUNTS ARE SUBJECT TO CHANGE*ountcsiDFaxExtrac USAitsemfor DoOnlysrelaDeNow! Direct TOLL-FREE accessto our Parts Department!Toll-free nationwide:800-421-1244Toll-free FAX:800/6-PARTS-7 800-672-7877Fax order discount and UPS special programs revised June 1, 1995WHITEMAN WM-700S, 700P — PARTS & OPERATION MANUAL — REV. #7 (06/26/01) — PAGE 5
RULES FOR SAFE OPERATION & SAFETY DECALS Do not operate or service this equipmentbefore reading the operating and maintenanceinstructions manual or serious injury mayresult. Do not operate this equipment unless allguards and safety devices are attached andin place. Stop the engine when leaving theequipment. When towing, an adequate safety chainmust be fastened to the frame, refer to page 9. Keep all inexperienced and unauthorizedpeople away from the equipment at all times. Unauthorized equipment modifications willvoid all warranties. Block the unit when leaving or when usingon a slope Wear safety glasses at all times whenworking around machinery. Maintain this equipment in a safe operatingcondition at all times. Caution must be exercised while servicingthis equipment. Rotating and moving parts cancause injury if contacted. Stop the engine before servicing, addingfuel and oil. Stop the engine and disconnect the sparkplug before allowing anybody’s hands in themixing drum. Check all fasteners periodically for tightness.Also check towing tongue bolt, lock nut andwheel lug nuts for wear. Never pour or spray water over the engineor electric motor. Always stand clear of dump handle whenmixer is in operation. Any binding of materialbetween the mixer blades and drum will causedrum and handle to quickly move in thedischarge position.The safety instruction decals shown must be on all Whiteman MixersCAUTION!SHUT OFF ENGINE BEFOREPUTTING HANDS IN MIXING DRUMCaution Decal is:P/N EM948423SAFETY INSTRUCTIONS1. Read owners manuals before operating.2. Keep unauthorized and untrained people away from machine during operation.3. Make sure all safety devices are in place before this machine is started.4. Make sure engine is turned off and spark plug wire is disconnected before cleaning themachine.5. Keep hands and fingers away from moving objects.6. Do not operate machine in an enclosed area. Proper ventilation is required.7. Never leave machine unattended when operating.8. Always stop engine and allow engine to cool before adding fuel or oil.WHITEMAN CONCRETE PRODUCTS A MULTIQUIP COMPANY CARSON, CALIFORNIAThe safety instruction decal is P/N 924801PAGE 6 — WHITEMAN WM-700S, 700P — PARTS & OPERATION MANUAL — REV. #7 (06/21/01)
WARRANTYThere are no warranties, express or implied, made by MultiquipInc. hereunder on Products manufactured or distributed by itexcept the warranty against defects in material and workmanshipon new Products to the original purchaser, as hereinafter setforth.Multiquip Inc. warrants Products manufactured by it to be freefrom defects in material and workmanship under normal andproper use and servicing for the periods specified on the bottomof this page. Warranty on the engines supplied with the Productsis limited to the warranty extended by the engine manufacturer.Multiquip Inc.’ sole obligation under this warranty is limited to thereplacement or repair, at its Carson, California facility, or suchauthorized facility, of only such part or parts thereof as shallappear to Multiquip Inc. upon inspection at such facility, to havebeen defective in material and workmanship.There are no warranties, express or implied, in addition to theabove except as may be provided in writing by Multiquip Inc.MULTIQUIP INC. SHALL NOT BE LIABLE FOR ANY SPECIAL,INDIRECT OR CONSEQUENTIAL DAMAGES.THE FOREGOING WARRANTIES ARE IN PLACE AND IN LIEUOF ALL WARRANTIES OF MERCHANTABILITY ANDFITNESS AND SETS FORTH THE ENTIRE OBLIGATION OFMULTIQUIP INC.To avoid misrepresentations with respect to Products soldhereunder, the Dealer agrees that no warranties, or otheroperating guaranties on any Products covered by this Agreementshall be made in excess of those made by Multiquip Inc.Multiquip Inc. Warranty Periods:A statement giving model and serial number of the Product, dateof sale to original purchaser and date and description of failureshall accompany all parts.WM-700 . 12 monthsAny part or parts determined by Multiquip Inc. to be defective willbe replaced free of charge, F.O.B. Carson, California. Returnedparts subject to warranty must be shipped prepaid to MultiquipInc. within 30 days from the date the defective part or parts wereremoved. This warranty does not apply to any part or parts whichhave been subject to abuse or unauthorized repairsWarranty with respect to Products, components and accessoriesnot manufactured by Multiquip Inc. is limited to the warrantyextended by the manufacturer of those items.WHITEMAN WM-700S, 700P — PARTS & OPERATION MANUAL — REV. #7 (06/26/01) — PAGE 7
WM-700S, 700P — OPERATIONSRefer to the following chart. For recommend plug sizes.MOTOR115 VOLT 1ØWM 700230 VOLT 1ØWM 900HORSEPOWERPIGTAIL CAP CONN BODYNEMA/NEMA/WHITEMAN WHITEMANPIGTAIL CAP CONN BODYNEMA/NEMA/WHITEMANWHITEMAN1½ & 3 HP L5-30P/940545 L5-30R/940546 L6-15P/940550 L6-15R/940551CONTROLSGENERALKILL SWITCH: (Gasoline Engine Only) Located on the side ofthe engine cover.The Whiteman WM-700 and WM-900 Series plaster and mortarmixers are quality mixers that have a batch capacity of 2.5 and3.5 bags respectively. With proper care, they will give continuousservice year-after-year.ENGINE THROTTLE AND CHOKE CONTROLS: Please referto the engine owners manual for specific instructions. Theelectric motor switch ( electric motor only) located on the motor— is used to start and stop the mixer.BEFORE STARTINGBefore starting the engine, read the engine owners manualand thoroughly understand the safety information.DUMP LATCH: To dump the tub, grasp the dump handle andlift the dump latch, then rotate the tub to discharge the mix.After, discharge, return the tub to the vertical mixing position.Check the items listed below:CLUTCHOil Levels. Be sure to check the oil levels in the engine andengine reduction unit before starting the unit.The paddle shaft and mixing blades are engaged anddisengaged by tightening and loosening the drive belts with aspring loaded idler pulley. To engage the clutch, rotate the levercounterclockwise. The spring maintains the correct belt tension.To disengage the clutch, rotate the lever clockwise against thelever stop. The engine base is slotted to adjust for belt wear andto bring the idler pulley into operating range.Hardware. Check all hardware on the mixer before starting.Periodically inspect all hardware. Loose hardware cancontribute to early component failure and poor performance.Use the torque chart below as a general guideline and keepall hardware tight:CAUTION: Stop the engine before allowing anybody to puttheir hands in the mixing drum.HARDWARE DIATORQUE (LB./FT.)%/16"-1814#/8" -1624WHEEL BEARINGS#/8" - 2437½" - 1339½" - 13 (Grade 8)90After every 3 months of operation, remove the hub dust cap andinspect the wheel bearings. Once a year, or when required,disassemble the wheel hubs remove the old grease and repackthe bearings forcing grease between rollers, cone and cagewith a good grade of high speed wheel bearing grease (neveruse grease heavier than 265 A.S.T.M. penetration (“No. 2.”) Fillthe wheel hub with grease to the inside diameter of the outerraces and also fill the hub grease cap. Reassemble the huband mount the wheel. Then tighten the adjusting nut, at thesame time turn the wheel in both directions, until there is aslight bind to be sure all the bearing surfaces are in contact.Then back-off the adjusting nut !/6 to ¼ turn or to the nearestlocking hole or sufficiently to allow the wheel to rotate freelywithin limits of .001" to .010" end play. Lock the nut at this position.Install the cotter pin and dust cap, and tighten all hardware.GASOLINE ENGINE CAREFor care and operation of the gasoline engine, refer to theengine manufacturer’s operating instructions furnished withthe engine. We recommend draining and refilling the enginecrankcase at least every thirty hours of operation. Check theengine oil level daily.ELECTRIC MOTOR CAREFor lubrication care and operation of the electric motor, refer toyour electric motor instruction booklet furnished with the motor.Protect the electric motor from dust as much as possible andkeep ventilating openings clean. Do not spray water on theelectric motor.PAGE 8 — WHITEMAN WM-700S, 700P — PARTS & OPERATION MANUAL — REV. #7 (06/21/01)
WM-700S, 700P — OPERATIONSBEARING BRACKETGrease the bearing bracket every month.COUNTERSHAFTNOTE: It is critical that the length of chain be properly adjustedto prevent the Draw Bar and front mixer stand fromdropping to the ground (contact) in the event the DrawBar becomes disconnected from the towing vehicle.STEP 1The countershaft rotates on two self-aligned pillow blockbearings. Grease these every 40 hours using grade #1 LithiumBase grease.DRAW BARGEAR ALIGNMENTThe countershaft and driven pinion are mounted on a slottedbase. To align gears, loosen the pillow block mounting bolts andmove them until the necessary alignment has been made.GEAR LUBRICATIONThe surface of the pinion and the bull gearshould be very lightly greased every 250 hours.IMPORTANT! AVOID OVER-GREASING.EXCESS GREASE WILL ACCUMULATECONTAMINATES AND CAUSE PREMATUREWEAR.BOLT & NUTINSERT CHAIN THROUGHTHE HOLESTEP 2DRAW BARIMPORTANT — DRUM HEAD SEAL CAREGrease seals every 40 hours of operation usingany grade #1 lithium base grease. Applygrease until visible inside of mixing tub(overgrease). This will purge seal system ofcontamination.FRAME ANGLEFRAME GUSSETCONNECTOR LINKDRUM GRILLSTEP 3The drum opening is covered by a steel grill that is hinged foreasy cleaning. This grill should be closed at all times when mixeris in use. Do not remove the grill or grill opening bar. Keep thegrill clean by washing it down daily.VEHICLECONNECTOR LINKDRAW BARCAUTION: Stop the engine before allowing anybody to put theirhands in the mixing drum.TOWING — Before towing, check with local and statelaws for proper compliance.The tow bar and chain must be properly attached to the mixerand towing vehicle prior to towing. Refer to the followinginstallation instruction:Step 1. Insert the Draw Bar into the main frame. Secure, utilizingthe ¾" bolt (grade 5) and nylock nut. Tighten to 100 foot pounds.Step 2. Install the chain through the hole located between theframe gusset and frame angle. Loop the chain together and placeunder the Draw Bar. Secure with connector link.Step 3. Extend the chain along the length of the Draw Bar,remove excess chain (slack) and secure to bottom connectorlink. Secure the chain to the towing vehicle, using the connectorlink.REMOVE EXCESSCHAIN (SLACK)BOTTOM CONNECTOR LINKSAFETY CHAIN .P/N 13363CONNECTOR LINK .P/N 01004WHITEMAN WM-700S, 700P — PARTS & OPERATION MANUAL — REV. #7 (06/26/01) — PAGE 9
WM-700S, 700P — OPERATIONSDANGERBEFORE TOWINGThe following is the recommended wiper blade adjustments:1) STEEL DRUM MIXERSSIDE SCRAPERBALL HITCH COUPLER1. Check vehicle hitch, ball, and coupler for signs of wear ordamage. Replace any parts that are worn or damagedbefore towing.2. Use only the 2" ball diameter as indicated on your coupler.Use of any other ball diameter will create an extremelydangerous condition which can result in separation of thecoupler and ball or ball failure.3. Be sure the coupler is secured to the hitch ball and thelock lever is down tight and locked.Recheck tightness again after towing about 50 miles.4. Check that trailer safety chains are properly connected.RECOMMENDED MAINTENANCE1. Smear ball socket and clamp face with chassis grease.Periodically oil pivot points and solutions surfaces ofcoupler with SAE 30 wt. motor oil.2. When parking or storing your trailer. Keep the coupler offthe ground so dirt will not build up in the ball socket.DANGEREND SCRAPER2) POLYETHYLENE DRUM MIXERSIf housing is deformed,replace complete coupler.USE ONLY GENUINEFULTON REPAIR KITS.CLEANING — BLADE ADJUSTMENTSAlways disconnect the spark plug wire before cleaning the insideof the drum.Never pour or spray water over the gasoline engine or electricmotor.For consistent performance, long life and high quality mixing,thoroughly clean the mixer inside and out at the end of eachday’s operation. To prevent lumps of dried mortar from formingand contamination of future batches, do not allow a buildup ofmaterials to form on the blades or anywhere inside the drum.The poly blade should come as close as possible to the surfacewithout touching. If material builds up on the drum, you may usea rubber mallet to dislodge the material without adverse effect tothe drum.IMPORTANT NOTICEEPOXY COMPATIBILITY — There are some expoxies and otherchemicals used in certain applications that are not compatiblewith polyethylene tubs.Since Whiteman Industries cannot control the end user’sapplication of this product, we will not assume responsibility forthe resulting damages when exposed to incompatible chemicals.PAGE 10 — WHITEMAN WM-700S, 700P — PARTS & OPERATION MANUAL — REV. #7 (06/21/01)
WM-700S, 700P — SPECIFICATIONSWM-700S SPECIFICATIONSMODELU.S.(inch)METRICCAPACITY . 7 CUBIC FEET . 198 LITERSBAG CAPACITY . 1½ - 2½ . 1½ - 2½WEIGHT (appROX.) . 788 LBS. . 357 KG.L X W X H . 71 X 50 X 56 IN. . 180 X 127 X 142 CM.LENGTH W/TOW BAR . 98 IN. . 248 CM.HEIGHT W/DUMP HANDLE . 73 IN. . 185 CM.DISCHARGE HEIGHT . 21 IN. . 53 CM.DRIVE . V-BELT TO GEAR . —DUMP ACTION . MANUAL . —WM-700P SPECIFICATIONSMODELU.S.(inch)METRICCAPACITY . 7 CUBIC FEET . 198 LITERSBAG CAPACITY . 1½ - 2½ . 1½ - 2½WEIGHT (APPROX.) . 788 LBS. . 357 KG.L X W X H . 71 X 50 X 56 IN. . 180 X 127 X 142 CM.LENGTH W/TOW BAR . 98 IN. . 248 CM.HEIGHT W/DUMP HANDLE . 73 IN. . 185 CM.DISCHARGE HEIGHT . 21 IN. . 53 CM.DRIVE . V-BELT TO GEAR . —DUMP ACTION . MANUAL . —WHITEMAN WM-700S, 700P — PARTS & OPERATION MANUAL — REV. #7 (06/26/01) — PAGE 11
EXPLANATION OF CODE IN REMARKS COLUMNHow to read the marks and remarks used in this parts book.Section 1: Items Found In the “Remarks” ColumnSerial Numbers-Where indicated, this indicates a serialnumber range (inclusive) where a particular part is used.Model Number-Where indicated, this shows that thecorresponding part is utilized only with this specific modelnumber or model number variant.Section 2: Items Found In the “Remarks” ColumnSerial Numbers-Where indicated, this indicates a serial numberrange (inclusive) where a particular part is used.Model Number-Where indicated, this shows that thecorresponding part is utilized only with this specific model numberor model number variant.Section 3: Items Found In the “Items Number” ColumnAll parts with same symbol in the number column, , #, , %, or , belong to the same assembly or kit.*Note: If more than one of the same reference number is listed,the last one listed indicates newest (or latest) part available.NOTEIf more than one of the same reference number islisted, the last one listed indicates newest (or latest)part available.NOTEThe contents of this catalog aresubject to change without notice.PAGE 12 — WHITEMAN WM-700S, 700P — PARTS & OPERATION MANUAL — REV. #7 (06/21/01)
WM-700S, 700P — SUGGESTED SPARE PARTSWM-700S/PWM-700S/P1 to 3 Units5 UnitsQty. P/NDescription3 . EM505834 . V-BELT3 . EM507846 . V-BELT, WM-700 ELECTRIC MOTOR6 . 491010 . LATCH ASSY3 . EM203010 . BLADE KIT STEEL DRUM3 . EM204624 . BLADE KIT POLY DRUM2 . EM902153 . BEARING, DRUM HEAD2 . 3131 . O-RING, DRUM HEAD2 . 3530 . SEAL KIT1 . 3351 . PINION GEARQty. P/NDescription5 . EM505834 . V-BELT5 . EM507846 . V-BELT, w/ELECTRIC MOTOR10 . 491010 . LATCH ASSY5 . EM203010 . BLADE KIT STEEL DRUM5 . EM204624 . BLADE KIT POLY DRUM4 . EM902153 . BEARING, DRUM HEAD4 . 3131 . O-RING, DRUM HEAD1 . EM940734 . SWITCH, ON/OFF2 . 3351 . DRIVEN PINON GEAR1 . EM500083 . DUMP HANDLE, POLY DRUM1 . EM201537 . DUMP HANDLE, STEEL DRUM4 . 3530 . SEAL KIT2 . 3065 . SEAL, AXLE2 . 3469 . DUST CAP AXLE2 . EM903049 . BEARING CONE UP TO S/N HL600002 . EM903113 . BEARING CONE STARTING S/N JA000002 . EM903012 . BEARING CUPNOTEPart numbers on this SuggestedSpare Parts List may supercede/replace the P/N shown in the textpages of this book.WHITEMAN WM-700S, 700P — PARTS & OPERATION MANUAL — REV. #7 (06/26/01) — PAGE 13
WM-700S, 700P — DRUM HEAD AND PADDLE SHAFT ASSYDRUM HEADTOW END27262528PADDLE SHAFT ASSEMBLYPAGE 14 — WHITEMAN WM-700S, 700P — PARTS & OPERATION MANUAL — REV. #7 (06/21/01)
WM-700S, 700P — DRUM HEAD AND PADDLE SHAFT ASSYDRUM HEAD & PADDLE SHAFT ASSEMBLYDRUM HEADNO.PART NO.PART 00076EM9160195028 B816430473131130025077193291U-BOLT2NUT HEX ½-134U-BOLT INSERT4DUST CAP . 1 . REPLACES 50017BEARING2BRACKET, DUMP BEARING . 2 . STARTING S/N 750180BRACKET, DUMP BEARING . 2 . S/N 750000 THRU 750105GREASE ZERK . 2 . REPLACES 491705COTTER PIN 1/8 X 2 . 2 . REPLACES 491690CASTLE NUT . 2 . REPLACES 502246SPACER . 2 . REPLACES 500089O-RING . 2 . REPLACES 491040SEAL . 2 . REPLACES 504749DRUM HEAD, BEARING BOSS . 2 . STARTING S/N 750180DRUM HEAD, BEARING BOSS . 2 . S/N 750000, THRU 750105REPLACES 500085SPRING . 2 . REPLACES 491930THIN SEAL SPACER . 14 . REPLACES 500088SEAL . 4 . REPLACES 500086SEAL URETHANE . 2 . REPLACES 500613SEAL KIT, PADDLE SHAFT . 1 . INCLUDES ITEMS 0QTY.REMARKS*PADDLE SHAFT ASSEMBLYNO.PART NO.PART NAME11617181920 #21 24EM203029PADDLE SHAFT1PADDLE ARM-TOW END1PADDLE ARM-CENTER1PADDLE ARM-ENGINE END1PADDLE ARM-CENTER1TOP STEEL BLADE4DRUM END STEEL BLADE2TOP RUBBER BLADE (STEEL) DRUM ONLY4TOP PLASTIC BLADE (POLY) DRUM ONLY4DRUM END PLASTIC BLADE (POLY) DRUM ONLY2DRUM END RUBBER BLADE (STEEL) DRUM ONLY2BOLT ½-13 X 3 ¾1LOCK WASHER ½ . 1 . REPLACES EM923638HEX NUT 1/2-13 . 1SPACER BULL GEAR1BLADE KIT, (STEEL) DRUM ONLY . 1 . INCLS w/ AND MTG. & HDWRBLADE KIT, (POLY) DRUM ONLY . 1 . INCLS w/# AND MTG. & HDWRHARDWARE KIT, (RUBBER/POLY BLADES) . 1 . INCLUDED IN BLADE KITS****QTY.REMARKS*WHITEMAN WM-700S, 700P — PARTS & OPERATION MANUAL — REV. #7 (06/26/01) — PAGE 15
WM-700S — STEEL DRUMSTEEL DRUM109110 111108PAGE 16 — WHITEMAN WM-700S, 700P — PARTS & OPERATION MANUAL — REV. #7 (06/21/01)
WM-700S — STEEL DRUMWM-700S - STEEL DRUMNO.PART NO.100101101101102103104105106 71508097508098***108109110111 PART NAMEQTY.REMARKSDUMP HANDLE1TOWING TONGUE (P. EYE) . 1 . NO LONGER AVAILABLETOWING TONGUE (PIN HOLE) . 1 . CONTACT MQ SALES DEPT./ACCESSORY ITEMTOWING TONGUE (BALL HITCH) . 1 . CONTACT MQ SALES DEPT./ACCESSORY ITEMCAP SCREW . 1 . REPLACES 505067LOCK NUT . 1 . REPLACES 505069DRUM GRILL1GRILL OPEN BAR1DRUM ASSY (STEEL) . 1 . INCLS. ITEMS w/DRUM & SHAFT ASSY. (COMPLETE)(STEEL) . 1 . INCLS. ITEMS w/ AND DRUM HEAD &PADDLE SHAFT ASSYEM506309MAIN FRAME1507264CLUTCH LEVER1EM507421DUMP LATCH1EM507835CLEVIS PIN113363SAFETY CHAIN1010045/16" CONNECTOR LINK2ILLUSTRATED ON PAGE 9*WHITEMAN WM-700S, 700P — PARTS & OPERATION MANUAL — REV. #7 (06/26/01) — PAGE 17
WM-700P — POLYETHYLENE DRUMPOLYETHYLENEDRUM121 122123124125116126123124PAGE 18 — WHITEMAN WM-700S, 700P — PARTS & OPERATION MANUAL — REV. #7 (06/21/01)
WM-700P — POLYETHYLENE DRUMPOLYETHYLENE DRUMMODEL WM-700PNO.PART NO.PART 3500083508022PLASTIC DRUM (W/O GRATES) . 1 . REPLACES 504522SUPPORT DRUM1STATIONARY GRATE1MOVEABLE GRATE1GRATE OPEN BAR1DUMP HANDLE1DRUM & SHAFT ASSY (COMPLETE) (POLY) . 1 . INCLS ITEMS w/ AND DRUMHEAD & PADDLE SHAFT ASSYHHCS 3/8" NC X 1 1/4" G-5 . 7 . REPLACES 492376LOCK NUT 3/8" NC . 7 . REPLACES492583FHCS 1/4" NC X 1" G-58LOCK NUT 1/4" NC . 8 . REPLACES 492581FHCS 3/8" NC X 2" G-512LOCK NUT 3/8" NC . 12 . REPLACES 7EM969079504943EM969013QTY.REMARKS*WHITEMAN WM-700S, 700P — PARTS & OPERATION MANUAL — REV. #7 (06/26/01) — PAGE 19
WM-700S, 700P — GAS ENGINES, PULLEYS & CAB ASSEMBLYCAB ASSEMBLYPAGE 20 — WHITEMAN WM-700S, 700P — PARTS & OPERATION MANUAL — REV. #7 (06/21/01)
WM-700S, 700P — GAS ENGINES, PULLEYS & CAB ASSEMBLYGAS ENGINES, PULLEYS & CAB ASSEMBLYCOMMON PARTSNO.PART NO.PART 30641141CAB ASSEMBLYLATCH ASSEMBLY .DRIVE GEAR 16-1/2 DIA.ROD ENDSPRINGIDLER PULLEYPILLOW BLOCK BEARINGSPRING CLIPDRIVEN PINION GEAR .SWITCH, ON/OFFCOUNTER SHAFTSNAP RINGS .KEYBOLT 3/8 X16 X 3-1/4KEY12 . REPLACES 5047441211211 . REPLACES 500272112 . REPLACES 490957111REMARKSMODEL WM 700 w/HONDANO.PART NO.PART A ENGINE GX240 K1HA 8HP .HONDA ENGINE GX160 5.5HP ENG.DRIVEN PULLEY-LARGEDRIVE PULLEY-5.5 HPDRIVE PULLEY-SMALL 1" BORE 8.0 HPV-BELTTHREADED RODIDLER ARM1 . REPLACES 4932611111211REMARKSMODEL WM 700 w/WISCONSINNO.PART NO.PART EM507771EM203352ENGINE WISCONSIN BKN2-408472 . 1 . REPLACES 505208DRIVEN PULLEY1DRIVE PULLEY1V-BELT2THREADED ROD1IDLER ARM1QTY.REMARKSMODEL WM 700 w/ROBINNO.PART NO.PART 0492057492054EM505834EM507490EM203352ROBIN ENGINE 8HP EY-28 .ROBIN ENGINE 8HP EH25-2 .DRIVEN PULLEY-LARGEDRIVE PULLEY-SMALLV-BELTTHREADED RODI
disassemble the wheel hubs remove the old grease and repack the bearings forcing grease between rollers, cone and cage with a good grade of high speed wheel bearing grease (never use grease heavier than 265 A.S.T.M. penetration ( "No. 2. ") Fill the wheel hub with grease to the inside diameter of the outer races and also fill the hub grease .
Depth 700 mm 700 mm 700 mm 700 mm 700 mm 700 mm 700 mm 700 mm 700 mm Width 635 mm 635 mm 635 mm 635 mm 680 mm 635 mm 680 mm 635 mm 680 mm CAPACITY GROSS VOLUME IN LITRES (AS 1430) Refrigerator PC 232 litres 250 litres 283 litres 280 litres 271 litres 314 litres 314 litres 229 litres 342 litres
The Rt. Rev. George N. Hunt The Rev. Frederick K. Jellison The Rev. Dn. Ida R. Johnson The Rev. Michaela Johnson The Rev. Paul S. Koumrian The Rev. Canon Harry E. Krauss * The Rev. H. August Kuehl The Rev. Richard T. Laremore * The Rev. Donald A. Lavallee The Rev. Canon John E. Lawrence The Rev. Dr. Gary C. Lemery * The Rev. Dn. Betsy Lesieur *
Apr 20, 2017 · PHEV Chevrolet Volt 53 1,700 18.4 BEV Mitsubishi i-MiEV 59 1,700 16 BEV smart electric drive 68 1,700 17.6 BEV BMW i3 60 Ah 81 1,700 21.6 BEV FIAT 500e 84 1,700 24 BEV Mercedes-Benz B250e (B-Class Electric Drive) 87 1,700 28 BEV Kia Soul EV 93 1,700 27 PHEV BMW i3 REx 97 1,700 33 BEV
700: 3/8 in maximum Input Power 208-575 V, 3- or 1-Phase Amperage Range 350: 3-350 A 700: 5-700 A Rated Output 350: 300 A at 32 V, 60% Duty Cycle 700: 600 A at 44 V, 60% Duty Cycle Weight 350: 135.5 lb (61 kg) 700: 198 lb (90 kg) Industrial Applications Precision Metal Fabrication Tube Mills Pipe and Tube Fabrication Tool and Die Exotic .
NACE Rev. 1.1 (ISIC Rev. 3) codes are often linked with more than one NACE Rev. 2 (ISIC Rev. 4) code. For example, 323 NACE Rev. 1.1 is linked with 261, 263 and 264 NACE Rev. 2 codes; 261 NACE Rev. 2 is linked with only one part of 311, 312, 313, 321 and 323 NACE Rev. 1.1 codes. Thus, it is not possible to obtain full codes of NACE
400 / 400-2 / 600 / 600-2 / 700 / 700-2 / 700-3 SERIES, MODEL 648PRO, ICB648PRO and UC SERIES CONDENSED ELECTRONIC CONTROL INFORMATION BOOKLET NOTE: If more detailed information on the electronic controls is needed, the appropriate
Bulletin No. 700-FE 700-FS 700-HR52, -HRP,-HRS, -HRT, -HRV 700-HRM/-HRC 700-HRF Type DIN Rail Timer DIN Rail Timer Multifunction Timer On-Delay Timer Twin Timer Features Only 17.5 mm wide
Bulletin No. 700-FE 700-FS 700-HR52, -HRP,-HRS, -HRT, -HRV 700-HRM/-HRC 700-HRF Type DIN Rail Timer DIN Rail Timer Multifunction Timer On-Delay Timer Twin Timer Features Only 17.5 mm wide
