Jackrabbit Service Parts Pre-cleaning Elevator & Woodchuck
JACKRABBIT SERVICE PARTS PRE-CLEANING ELEVATOR & WOODCHUCK Phone (209) 599-6118 Fax (209) 599-6119 E-mail sales@jackrabbit.bz or info@jackrabbit.bz 01/01/2013
TO OUR CUSTOMERS: Thank you for choosing JackRabbit. We stand behind our products and are very proud of the equipment we design and manufacture. Preventive maintenance is the easiest and least expensive type of maintenance. Please take the time to review this Owner’s Operator’s Manual it can save you time and expense. WARRANTY JACKRABBIT warrants each new piece of equipment and parts manufactured by it to be free from defects in material and workmanship under normal use and service. The obligation of JACKRABBIT shall be limited to replacing any part which shall, within 1 year (1 season) after delivery to the original purchaser, be returned to JACKRABBIT with transportation charges prepaid and which an examination by JACKRABBIT discloses defective. This Warranty does not obligate JACKRABBIT to bear the cost of labor, travel time or hauling in connection with the replacement or repair of the defective parts and in no event will be liable for consequential damages including but not limited to loss of crop, rental or substitute equipment or other commercial loss. No warranties or representations made by persons other than representatives of JACKRABBIT expressly authorized in writing to do so shall be valid and binding upon JACKRABBIT. No dealer shall be authorized to bind JACKRABBIT in this respect. JACKRABBIT makes no warranty with respect to component parts not manufactured by JACKRABBIT. This warranty shall not apply to any equipment which has been altered in any way outside of manufacturers factory, or which has been subject to misuse, neglect or accident. This warranty is expressly in lieu of all other warranties and representations, expressed, implied, or statutory, including warranties of merchantability and fitness for a particular use, and all other liabilities or obligations on the part of JACKRABBIT, foreseeable or not. USER’S RESPONSIBILITY It is the responsibility of the user to read the Operator’s Manual and understand the safe and correct operating procedures as pertains to the operation of the product and to lubricate and maintain the product according to the maintenance schedule in the Operator’s Manual. WARRANTY SERVICE Warranty service may be obtained through an authorized dealer or JackRabbit service facility. Write or call: JackRabbit, 471 Industrial Ave, CA 95366, telephone (209) 599-6118
TABLE OF CONTENTS Page A. INCLINE CONVEYOR 1-3 B. HORIZONTAL CONVEYOR 4 C. ENGINE 5-6 D. ELECTRICAL 7-8 E. WOODCHUCK DESTICKER 9 F. MISC. PARTS LIST 10 G. HYDRAULIC 11-12
PARTS LIST INCLINE CONVEYOR PART # DESCRIPTION REF 26034 Incline Conveyor Motor A1 26034A Incline Conveyor Motor Seal Kit N/A 29502 Split Coupler 1-1/2” ID A3 GC095 Rod Belt 24-3/4" Drive Shaft / Roller A10 GC055 Rod Belt Return Shaft A6A GC077 Rod Belt 9" Return Shaft Flange Roller A6 GC078 Rod Belt 3-1/2" Idler Flange Roller A7 GC076 Rod Belt 3" Idler Roller A9 GC074 Rod Belt 3-1/4" Idler Roller A8 28898 Z-Belt 30" Drive Shaft / Roller A5 GC082 Z-Belt Snub Shaft / Roller A4 26018 Z-Belt Idler Roller 30 -3/8" x 1-3/4" A17 24341 B Idler Shaft / Roller 30" A19 27307 Bearing Housing For 30-3/8" x 1-3/4" Idler roller N/A 27306 Bearings for 30-3/8" x 1-3/4" Idler Roller N/A 22097 Bearing (VAK 1-1/2” Pillow Block) A2 28518 Bearing (VCJT 1-1/4S" Flange) A6B 26614 Bearing (VCJT 1" Flange) A4A GC056 Z-Belt with Walnut Flights - 30" x 525" (Serial #475)N/A GC056A Z-Belt with Walnut Flights - 30" x 597" N/A GC070 Z-Belt - Almonds 30" x 525" (Serial # 575) A11 GC070A Z-Belt - Almonds 30" x 597"(Serial #624----) A11 27523A Z-Belt 30"Lace Pin A21 26887 Belt Wipers (UHMW 37") 30" Incline Belt A18 24653 Incline Belt Brush A15 24654 Brush Holder A16 GC071 Rod Belt - Walnut (Serial# 475) A13A GC072 Rod Belt - Almond (Serial # 575----) A13 GC067 Rod Belt Rubber Seal Strip A14 GC045 Rod Belt Seal (UHMH) A12 28120 Transition Seal Incline Belt (UHMW) A20 1
INCLINE CONVEYOR (CONTINUED) 2
INCLINE CONVEYOR (CONTINUED) A17 A18 A20 A19 3
HORIZONTAL CONVEYOR PART # DESCRIPTION REF 22977 Bearing (VAK 1" Pillow Block) B1 24340A Drive Roller 20 ¼" W/Lag B8 26464 Bearings Pad B2 25070 20-3/8" x 1-3/4" Idler Roller B10 27307 Bearing Housing For 20-3/8" x 1-3/4" Idler roller 27306 Bearings for 20-3/8" x 1-3/4" Idler Roller GC057 (20" x 412") Horizontal Belt B11 27377 (20” x 316”) Horizontal Belt Front Wheel Drive 27523 20" Belt Lacing Pin B12 24556 Belt Wiper UHMW 27 ¾" B9 26765 Transition Seal UHMW B6 29104 Lower Hyd. Motor (RE-18) B5 27553 Seal Kit Motor for (RE-18) 26493 Belt Drive Coupler 1" B3 28935 Torque Arm B4 GC037 20" x 56" Rear Belt Skid Pan (Welded Replacement) 24371 20" x 64 ½"Front Belt Skid Pan (Welded Replacement) 26045A 20" Bin Extension Upper B7 B9 B6 B7 B10 4 B8 B11 B12 B7
ENGINE PARTS PART # DESCRIPTION 27014 Air Filter Inner (Don. P829332) 27013 Air Filter-Outer (Don. P827653) 27015 Air Filter Assemble G0700018 27015A Air Filter Mounting Band P777731 27015B Air Filter Vacator Valve P158914 28795 Restriction Indicator (Deutz) 27013A Filter Housing End Cover (P636202) 27011 Fuel Filter (Duetz 117-4696) 27943 Fuel Strainer in line 117-8753 27010 Oil Filter (Duetz 117-4416), F2L 1101 &2011 28158 Dip Stick (427-2816) 3 Cyl 27168A Fan Belt (Duetz 117-9565) 27202D Fuel Shut off Solenoid (0428-7583) 27203C Fuel Pump (428-6113), F2L, F3L, F4L 2011 27492 Fuel Injector Return Line Kit 0417-8631 28419D Fuel Injector Return Line Per Foot 0417-8632 27656 Throttle Solenoid (1756E) 27657 Coil Commander (SA4667) 27310 Throttle Linkage Kit, assembly 24744C Throttle Ball Joint, 90 degree 24744D Throttle Hex Spacer 24744E Throttle Straight Connection 27776 Throttle Lever 417- 9754 for Duetz 1011 27803B Alternator New 01182434 for 2, 3, 4 Cyl Eng. 25026 Exhaust Pipe 24752 Exhaust Pipe Hanger 27959 Rubber Ring Isolator Duetz Engine 27407 Oil Cooler for 3 Cylinder Engine 27876A Oil Pressure Sender (CH86281) three prong 22424 Hour Meter 27762 Drive Plate Kit, (Drive & Bell Housing Cover) 29564 Drive Plate 27285 Gas Shock for Engine Door 5 REF C1 C2 C3 N/A C4 C5 C6 C7 C8 C9 C10 C11 C12 C13 C14 N/A C15 C16 C17 C17A C17B C17C C18 C19 N/A N/A C20 N/A C21 C22 N/A C23 C24
ENGINE PARTS (CONTINUED) C1 C7 C6 C5 C3 C4 C2 C8 C11 C9 C12 C10 C14 C15 C16 C13 C B A C18 C20 C19 C17 C21 C24 C22 C23 6
ELECTRICAL PART # 26403 27527 28213 22416 22416A 27131A 27876A 27145 27145A 27123 26399 24564 27657 27118 27202D 27203B 27656 22424 27803B DESCRIPTION Rocker Switch (1TP4-2) Throttle & Belt Toggle Switch (1TL1-2) @ Momentary Toggle Switch (1NT1-7) @ Momentary on/off Key Switch (Polak 331-196) Key Polak for 22416 Engine Oil Temperature Gauge 2” hole Oil Pressure Sender (CH86218) three prong Deutz Idiot Light Assembly (Red) Deutz Idiot Light Assembly (Green) Light Bulb Only Circuit Breaker 30 AMP Electrical Wiring Harness for 20/30 Timer Module Switch, Jack-Chute Momentary Solenoid W/ O-Ring, Fuel Shut Off Solenoid O-Ring Solenoid, Throttle Hour Meter Alternator D1 D2 REF D1 D2 D3 D4 N/A D5 D6 D7 D8 D9 D10 D11 D12 D13 D14 N/A D15 D16 D17 D3 D4 D5 D7 D6 D8 D11 D9 D10 D12 D14 D13 D17 D15 D16
ELECTRICAL (CONTINUED) 7
WOODCHUCK 8 PART # DESCRIPTION 29503 Seal kit of 29358 and 29357 22190 Elevator Bolt 25386 Wear Slide 7” 26129 Wear Slide 25.5” 26120 Desticker Chain Assy. 26780 Desticker Link without Flags 27141 Desticker Master Link CA557 24395 Torque Arm 4.5” Pin 24395D Torque Arm 7.25” Pin 26493 S Split Coupler 1” 24395 Torque Arm 9” Pin 26046 Desticker Flag 26780A Desticker link w/ 3 Flags 24491 Wear Slide 46” 26780B Desticker link w/ 4 Flags 26143 Drive Shaft 1”x 30.75” 26144 Idler Shaft 1” x30.25” REF E1 E2 E3 E4 E5 E6 E7 E8 E9 E10 E11 E12 E13 E14 E15 N/A N/A E3 E1 E2 E4 E6 E7 E5 E8 E12 E9 E10 E11 E13 E15 E14 9
MICS. PARTS PART # 28336 27020B 28784 28247 28246 28487 28489A 28489 28488 DESCRIPTION Tire Rim Tire Remote Kit Remote Receiver Remote Transmitter Antenna Mount Gigalink Cable Coax Cable Antenna REF N/A N/A F1 F2 F3 F4 F6 F7 F5 F2 F3 F4 F1 F7 F5 F6 10
HYDRAULICS PARTS PART # DESCRIPTION 29726 Sun Vented Relief 27386 Strainer GPM GC079 Desticker Pump GC086 Non Desticker Pump 29358 RS/WR 18 29357A RS/WR 10/18 SEAL KIT 29357 RS/WR 10 27762 Drive Plate Kit 27317 Frda Xan 27317A Frda Xan Seal Kit 29555 Valve (SV-10) 27312 Valve Coil 29554 Valve (SV-16) 27314 RPEC Fan 27314A RPEC Fan Seal Kit 23548A Hydraulic Filter 28842 Hydraulic Fluid Cap 24669 Sight Level Gage 24671 Strainer 15GPM 2”x1.25” 27386 Strainer 15GPM 1.5”x1” 26612 2”x24” Cylinder 26199 1” Double Clamp 26034A MLHT 500 26242 RE 18 G1 G3 G2 REF G1 G2 G3 G4 G5 G5A G6 N/A G8 G8A G9 G10 G11 G12 G13 G14 G15 G16 G17 G18 G19 G20 G21 G22 G4 G5 G8A G6 G5A G9 G8 G10 G11 G15 Drw REF N/A N/A 58 61 49 N/A 50 N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A 75 76 77 78 N/A 62 63 G12 G16 G17 G21 G22 G18 G20 11 G14 G13 G19
HYDRAULICS PARTS (CONTINUED) 12
SERVICE PARTS PRE-CLEANING ELEVATOR & WOODCHUCK Phone (209) 599-6118 Fax (209) 599-6119 . Please take the time to review this Owner's Operator's Manual it can save you time and expense. . (Deutz) C5 27013A Filter Housing End Cover (P636202) C6 .
Please take the time to review this Owner's Operator's Manual it can save you time and expense. WARRANTY JACKRABBIT warrants each new piece of equipment and parts manufactured by it to be free from defects in material and workmanship under normal use and service. The obligation of . 144 28325 Deutz 4 Cylinder Turbo Engine # TD 1
RABBITS OF SLOAN CANYON . Desert Cottontail Black-tailed Jackrabbit . The desert cottontail can be seen in the early morning or late afternoon. It mainly eats grass and other plants. It is much smaller than the jackrabbit with a tail that looks like a cotton ball. Reaching a length of about two feet and a weight from four to six
The following topics in the Introduction to Green Cleaning and Green Cleaning Programs training manual were covered: § New York State Green Cleaning Product Mandates and products currently covered under the mandates; § Reasons for creating the green cleaning mandates; § A description of green cleaning;
Catamount Carpet Cleaning, P.O. Box 566, Wilmington, VT 05363 802-464-3839, 297-3419, 254-8466, www.catamountcarpet.com catcarpt@together.net CLEANING TOUR Welcome to our Cleaning Tour! We will take you on a quick trip through our cleaning process, from pre-cleaning inspection to finishing work.
for I&I Cleaning ChemicalsExpenditures .21 267 Motor Vehicle Indicators.24 8 Manufacturers' Shipments .27 9 Nonresidential Cleaning Service Revenues 29 2810 5I&I Cleaning Chemical Pricing .31 11 Cleaning ChemicalsI&I Cleaning Chemical Market, 1999-2009 33
Cleaning: How To Do It 1. Include step-by-step procedures for precleaning, cleaning during the job, and daily and final cleanings in project design or specifications. 2. Assign responsibilities to specific workers for cleaning and for maintaining cleaning equipment. 3. Have sufficient cleaning equipment and supplies before beginning work. 4.
After cleaning is completed and the floor covering has dried it must be suction cleaned to remove any residues of dirt and cleaning agent. 2.4 Restorative Cleaning Restorative cleaning (also referred to as deep cleaning _) is aimed at returning the installed textile floor covering to as clean a condition as possible. It uses
and hold an annual E-Safety Week. Our Citizenship Award. 4 Through discussion in all our history themes – the rule of law is a key feature. RE and citizenship/PSHEE lessons cover religious laws, commandments and practices. In RE we encourage pupils to debate and discuss the reasons for laws so that all pupils understand the importance of them for their own protection. As part of the .
