User Manual - AAMP

User Manual

IntroductionThe Autoleads ControlPro CP2-VO53 is a universal steeringcontrol interface that is set using a pre-defined dipswitchconfiguration and supplied with a wiring harness for Fordvehicles, which allows retention of steering wheel controls,and retained accessory power whenever replacing a factoryradio. Use of this interface also allows you to program tworadio functions to each steering wheel control button by usingshort press/long press dual command functionality. The CP2is compatible with vehicles that use data or analog steeringwheel controls.Key FeaturesuuuuuuuuCompatible in vehicles equipped with LAN, LIN, CAN,Class II, Analog or Serial Data Steering wheel controlsEasily configurable using either a PC or manuallyRetains memory even if power is lostAbility to assign two radio functions to one steeringwheel buttonUpdatable via the Autoleads PC Application.Create and save custom vehicle configuration files forlater use.Highly visible tri-colour LED to keep the user informedof the modules status.Equipped with a manual learning function forcompatibility with unlisted vehicles equipped with analogsteering wheel controls.Interface & Wiring OverviewFor compatible vehicles, please refer to the nextsection of this manual or visitwww.autoleads.co.uk/controlpro to download thePC application or phone app that provides furthervehicle specific wiring and vehicle dipswitchconfigurationsemail - technical.eu@aampglobal.comwww.autoleads.co.uk

Interface & Wiring Overview (continued)ProgrammingButtonStatus cleDipswitchesRadioDipswitchesUSB Port( ) Accessory 12v Input(-) Analog SWC Ground(-) Chassis Ground( ) Accessory 12v Output(-) Analog SWC Input 1( ) Constant 12v InputData 2 Input(CAN-low)Data 1 Input (LAN, MSCAN, SWCAN, LEFT)PinkLight Green ( ) 12v Analog SWC InputWhite/Red (-) Analog SWC Input 3White/Black (-) Analog SWC Input 2Data 2 Input (LIN, IBUS, CLASSII, SERIAL)PurpleBlue/Yellow SWC Output - Kenwood/Newer JVC3.5mm JackSWC Output - Alpine, JVC, Clarion,Pioneer, Sony, Boyo, Dual, Advent,Lightning Audio or VisteonInstallationPlease visit www.autoleads.co.uk/controlproto download the PC application or phone app thatprovides vehicle specific wiring and vehicle dipswitchconfigurationsConfiguration & ProgrammingVehicle Dipswitch SettingThe dipswitches on the side of the interface must be manuallyset to the proper vehicle and radio configuration by the user.Set the dipswitches and then connect it to the vehicle/radio forit to function.Both vehicle and radio dipswitch settings must be setbefore the module is connected to the vehicle.email - technical.eu@aampglobal.comwww.autoleads.co.uk

VehicleDipswitchConfigurationVolvo S60Volvo V70Volvo XC70(01-04)(01-04)(00-04)Volvo S60Volvo S80Volvo V70Volvo XC70Volvo XC90(04-07)(98-06)(04-07)(04-07)(02-14) Right ArrowUp Arrow Volume Volume Seek / Track / FFWSeek - / Track - / RRWFor illustrative purposes onlyemail - technical.eu@aampglobal.comwww.autoleads.co.uk

Radio Dipswitch SettingsRadio Dipswitch erPioneerSonyManual Configuration ModeIf you wish to re-assign button functions or use shortpress/long press dual command functionality, please followthe PC application or manual re-assignment procedure.1. Please Visit www.autoleads.co.uk/controlpro todownload the Autoleads ControlPro application. Launch theapplication and find your vehicle/radio combination.2. Set the vehicle dipswitches according to the application.3. Set the radio dipswitches according to the radio dipswitchchart above.4. Connect the interface according to the installationinstructions and test functionality.email - technical.eu@aampglobal.comwww.autoleads.co.uk

PC Application ModeWith this method, the CP2 can be connected to a PC in whichthe application assigns the vehicle and steering wheel buttonfunctionality. To configure using a PC, the dipswitches onthe side of the interface must all be set to the down/onposition. When using this method, it is not required tomanually set the dipswitch positions when programmingvia the PC App mode.1. Visit www.autoleads.co.uk/controlpro to downloadthe Autoleads ControlPro PC application.2. Connect the CP2 module to the PC via the USB port. Whenusing a PC to configure, it is not required to power the CP2module via the 11 pin connector.PLEASE NOTE:3. It may be necessary to update your Microsoft .NETFramework. If you require this update your PC willautomatically notify you. If you do not get a notification,then you do not require the update.4. Launch the application and follow the on screen prompts.Manual Programming ModeWith this method the steering wheel button values must bemanually programmed into the CP2 by using either the PCapplication or the programming button located on the module.The vehicle dipswitches on the side of the interface must all beset to the up (off) position.PLEASE NOTE: This mode is only compatible in vehicleswith both analog steering controls and a 12v Accessorywire. Vehicles with CAN-Bus buttons cannot be manuallyprogrammed.The radio dipswitches must be set to the correct radioconfiguration.1. Visit www.autoleads.co.uk/controlpro to downloadthe Autoleads ControlPro PC application.2. Launch the application and find the installation instructionsfor your vehicle3. Set the radio dipswitches according to the chart below.4. Connect the interface according to the installationinstructions.5. You can now either connect the CP2 to your PC and use theapplication to program the steering control values or follow theprogramming instructions in the next step.email - technical.eu@aampglobal.comwww.autoleads.co.uk

Manually Mapping the SteeringWheel ButtonsPLEASE NOTEThis section only applies to button programming in manualprogramming mode. If you are using the CP2 in manualconfiguration mode (specific vehicle dipswitch settings)and wish to re-assign button functions, please follow the“Steering Wheel Button Re-Assignment” sectionPlease read each of the following steps to familiarise yourselfwith the process before beginning.The interface must be programmed in the specific order shownin the chart below1. Turn the key to the ignition position. The LED on the CP2module will illuminate red.2. Press and hold the programming button on the side of theCP2 interface until the LED illuminates green Release theprogramming button.Within 7 seconds, press the button that is to be learned on thesteering wheel. At this point you have two optionsa. For short press functionality: Hold the button on thesteering wheel until the LED changes from green to red.Release the button.b. For long press functionality: Continue to hold the buttonuntil the LED flashes between red and amber once. Releasethe button.4. If you need to program more buttons, repeat step 3 foreach additional audio function on the steering wheel.5. If you come across a function in the chart that your steeringwheel does not have, or you do not want to program, pressand release the program button on the side of the CP2interface to skip that function. The LED will turn off then backon when the skip has been done successfully.6. Once programming is completed, wait seven seconds.The LED will flash green 3 times indicating the end ofprogramming.7. Test the interface for proper functionality. Whenever a SWCbutton is pressed the LED on the interface should blink green.If any function does not work, repeat the programming steps.Please reference the Radio Function Mapping Order on thenext page.email - technical.eu@aampglobal.comwww.autoleads.co.uk

email - iveEnd1314Band/Program12Track -811SelectTrack 7PowerSource6Enter/PlayPreset -59Preset 410Preset/Disc -Mute3PowerVoice DialPhone RejectPhone ReceiveAttenuationBand/Disc Track -Track SourceMuteVolume -Volume -Volume Volume 2JVC1AlpineVoiceEndSendSend/EndBandSearch -Search SourceMuteVolume -Volume Clarion/NakamichiBandTrack -Track SourcePreset -Preset MuteVolume -Volume Other*Answer/End CallReject Call/Source (Bluetooth radios only)BandTrack -Track SourcePreset -Preset MuteVolume -Volume Sony*Other Advent, Boyo, Dual, Lightning Audio, Rockford Fosgate, & VisteonMuteOff HookOn HookVoice DialAnswerDisc/AM -Disc/FM Track -Track PlaySourceMuteVolume -Volume KenwoodVoice ActivationEnd CallAnswer CallPhone MenuBandTrack -Track SourcePreset -Preset MuteVolume -Volume PioneerPowerAudioTrack -Track SourceMuteVolume -Volume FusionRadio Function Mapping Order

SWC Button Re-Assignment ProcedurePLEASE NOTEThis section only applies to button re-assignment withina configuration. If you are using the CP2 in manualprogramming mode (all vehicle dipswitches up) pleaserefer to the “Manually Mapping the Steering WheelButtons” section.If you wish to re-assign the Steering wheel control functionsor utilise short press long press dual command functionalityyou will need to follow the steps outlined in this section.Please read each of the following steps to familiarise yourselfwith the process before beginning. The interface must beprogrammed in the specific order shown in the chart on thenext page.1. Turn the key to the ignition position.The LED will illuminate red.2. Press and hold the programming button on the side ofthe interface until the LED illuminates green Release theprogramming button.3. Within 7 seconds, press the button that is to be learnedon the steering wheel. At this point you have two options:a. For short press functionality: Hold the button on thesteering wheel until the LED changes from green to red.Release the button.b. For long press functionality: Continue to hold the buttonuntil the LED flashes be-tween red and amber once.Release the button.4. If you need to program more buttons, repeat step 3 for eachadditional audio function on the steering wheel.5. If you come across a function in the chart that your steeringwheel does not have, or you do not want to program, pressand release the program button on the side of the interface toskip that function. The LED will turn off then back on when theskip has been done successfully6. Once programming is completed, wait seven seconds.The LED will flash green 3 times indicating the end ofprogramming.7. Test the interface for proper functionality. Whenever a SWCbutton is pressed the LED on the interface should blink green.If any function does not work, repeat the programming stepsThe steering wheel controls can always be restored to default settingsby pressing and releasing the program button on the side of the interfaceonce and waiting 7 seconds for the descending chime and the LED toflash 4 times. This reset can only be done while the CP2 module isconnected to the vehicle.email - technical.eu@aampglobal.comwww.autoleads.co.uk

email - iveEnd1314Band/Program12Track -811SelectTrack 7PowerSource6Enter/PlayPreset -59Preset 410Preset/Disc -Mute3PowerVoice DialPhone RejectPhone ReceiveAttenuationBand/Disc Track -Track SourceMuteVolume -Volume -Volume Volume 2JVC1AlpineVoiceEndSendSend/EndBandSearch -Search SourceMuteVolume -Volume Clarion/NakamichiBandTrack -Track SourcePreset -Preset MuteVolume -Volume Other*Answer/End CallReject Call/Source (Bluetooth radios only)BandTrack -Track SourcePreset -Preset MuteVolume -Volume Sony*Other Advent, Boyo, Dual, Lightning Audio, Rockford Fosgate, & VisteonMuteOff HookOn HookVoice DialAnswerDisc/AM -Disc/FM Track -Track PlaySourceMuteVolume -Volume KenwoodVoice ActivationEnd CallAnswer CallPhone MenuBandTrack -Track SourcePreset -Preset MuteVolume -Volume PioneerPowerAudioTrack -Track SourceMuteVolume -Volume FusionSWC Button Re-Assignment Procedure