Fcc Part 15 Test Report
FCC PART 15 TEST REPORT No.I22Z61813-IOT06 for Honor Device Co., Ltd. Smart Phone RMO-NX3 With FCC ID: 2AYGCRMO-NX3 Hardware Version: HN2RMOM Software Version: 6.1.0.21(C900E21R1P1) Issued Date: 2022-11-04 Note: The test results in this test report relate only to the devices specified in this report. This report shall not be reproduced except in full without the written approval of CTTL. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the U.S.Government. Test Laboratory: CTTL-Telecommunication Technology Labs, CAICT No. 52, Huayuan North Road, Haidian District, Beijing, P. R. China 100191. Tel: 86(0)10-62304633-2512, Fax: 86(0)10-62304633-2504 Email: cttl terminals@caict.ac.cn, website: www.caict.ac.cn Copyright. All rights reserved by CTTL.
No.I22Z61813-IOT06 REPORT HISTORY Report Number Revision Description Issue Date I22Z61813-IOT06 Rev.0 1st edition 2022-11-04 Copyright. All rights reserved by CTTL. Page 2 of 15
No.I22Z61813-IOT06 CONTENTS CONTENTS . 3 1. TEST LATORATORY . 4 1.1. 1.2. 1.3. 1.4. 1.5. 2. INTRODUCTION & ACCREDITATION . 4 TESTING LOCATION . 4 TESTING ENVIRONMENT. 4 PROJECT DATE . 4 SIGNATURE . 4 CLIENT INFORMATION . 5 2.1. 2.2. 3. APPLICANT INFORMATION . 5 MANUFACTURER INFORMATION . 5 EQUIPMENT UNDER TEST (EUT) AND ANCILLARY EQUIPMENT(AE) . 6 3.1. 3.2. 3.3. 4. ABOUT EUT . 6 INTERNAL IDENTIFICATION OF EUT USED DURING THE TEST . 6 GENERAL DESCRIPTION . 6 REFERENCE DOCUMENTS . 7 4.1. 4.2. DOCUMENTS SUPPLIED BY APPLICANT . 7 REFERENCE DOCUMENTS FOR TESTING . 7 5. LABORATORY ENVIRONMENT . 7 6. SUMMARY OF TEST RESULTS . 7 6.1. 6.2. 7. SUMMARY OF TEST RESULTS . 7 STATEMENTS. 7 TEST EQUIPMENTS UTILIZED . 8 ANNEX A: MEASUREMENT RESULTS . 8 A.1. MEASUREMENT METHOD . 8 A.2. CHANNEL MOVE TIME AND CHANNEL CLOSING TRANSMISSION TIME . 11 A.3.NON-OCCUPANCY PERIOD . 13 A3.1 ASSOCIATED TEST . 13 ANNEX B: EUT PARAMETERS. 15 ANNEX C: ACCREDITATION CERTIFICATE . 15 Copyright. All rights reserved by CTTL. Page 3 of 15
No.I22Z61813-IOT06 1. TEST LATORATORY 1.1. Introduction & Accreditation Telecommunication Technology Labs, CAICT is an ISO/IEC 17025:2017 accredited test laboratory under NATIONAL VOLUNTARY LABORATORY ACCREDITATION PROGRAM (NVLAP) with lab code 600118-0, and is also an FCC accredited test laboratory (CN5017), and ISED accredited test laboratory (ISED#: 24849). The detail accreditation scope can be found on NVLAP website. 1.2. Testing Location Conducted testing Location: CTTL(Huayuan North Road) Address: No. 52, Huayuan North Road, Haidian District, Beijing, P. R. China100191 1.3. Testing Environment Normal Temperature: Relative Humidity: 15-35 C 20-75% 1.4. Project date Testing Start Date: Testing End Date: 2022-10-09 2022-11-04 1.5. Signature Xie Xiuzhen (Prepared this test report) Zheng Wei (Reviewed this test report) Pang Shuai (Approved this test report) Copyright. All rights reserved by CTTL. Page 4 of 15
No.I22Z61813-IOT06 2. CLIENT INFORMATION 2.1. Applicant Information Company Name: Address: City: Country: Telephone: Fax: Honor Device Co., Ltd. Shum Yip Sky Park, No. 8089, Hongli West Road, Shenzhen, China Shenzhen China / / 2.2. Manufacturer Information Company Name: Address: City: Country: Telephone: Fax: Honor Device Co., Ltd. Shum Yip Sky Park, No. 8089, Hongli West Road, Shenzhen, China Shenzhen China / / Copyright. All rights reserved by CTTL. Page 5 of 15
No.I22Z61813-IOT06 3. EQUIPMENT UNDER TEST (EUT) AND ANCILLARY EQUIPMENT(AE) 3.1. About EUT Description Model name FCC ID WLAN Frequency Band Type of modulation Antenna Extreme vol. Limits Device Type (DFS) TPC mechanism Antenna gain Smart Phone RMO-NX3 2AYGCRMO-NX3 ISM Band: -5250MHz 5350MHz -5470MHz 5725MHz OFDM Integral Antenna 3.87V Client without radar detection(only support client mode) Not support 0dBi 3.2. Internal Identification of EUT used during the test EUT ID* IMEI HW Version SW Version UT07a 869123060002698/ HN2RMOM 6.1.0.21(C900E21R1P1) 869123060006962 *EUT ID: is used to identify the test sample in the lab internally. UT07a is used for Conduction test. 3.3. General Description The Equipment Under Test (EUT) is a model of Smart Phone with integrated antenna. It consists of normal options: lithium battery, charger. Manual and specifications of the EUT were provided to fulfil the test. Copyright. All rights reserved by CTTL. Page 6 of 15
No.I22Z61813-IOT06 4. REFERENCE DOCUMENTS 4.1. Documents supplied by applicant EUT feature information is supplied by the applicant or manufacturer, which is the basis of testing. 4.2. Reference Documents for testing The following documents listed in this section are referred for testing. FCC CFR 47, Part 15, Subpart E: 15.407 General technical requirements. UNII Clients Without Radar Detection New Rules v01r02 FCC Part15 KDB 905462 D03 2021 2016 5. LABORATORY ENVIRONMENT Measurement is performed in shielding room. 6. SUMMARY OF TEST RESULTS 6.1. Summary of Test Results SUMMARY OF MEASUREMENT RESULTS Channel move transmission time time and channel Non-Occupancy Period closing Sub-clause of Part15E Verdict 15.407 (h)(2)(iii) P 15.407 (h)(2) (iv) P Please refer to ANNEX A for detail. Terms used in Verdict column P Pass, The EUT complies with the essential requirements in the standard. NM Not measured, The test was not measured by CTTL NA Not Applicable, The test was not applicable F Fail, The EUT does not comply with the essential requirements in the standard 6.2. Statements CTTL has evaluated the test cases requested by the client/manufacturer as listed in section 6.1 of this report for the EUT specified in section 3 according to the standards or reference documents listed in section 4.1. This report only deal with the UNII DFS functions among the features described in section 3, and The EUT met all requirements of the reference documents. The end user is not available to get and modify the parameters of the detected Radar Waveforms in this product. Test Conditions T nom Normal Temperature T min Low Temperature T max High Temperature V nom Normal Voltage V min Low Voltage V max High Voltage H nom Norm Humidity Copyright. All rights reserved by CTTL. Page 7 of 15
No.I22Z61813-IOT06 A nom Norm Air Pressure For this report, all the test case listed above is tested under Normal Temperature and Normal Voltage, and also under norm humidity, the specific conditions as following: Temperature T nom 26 Voltage V nom 3.87V Humidity H nom 44% Air Pressure A nom 1010hPa 7. TEST EQUIPMENTS UTILIZED Conducted test system No. Equipment 1 Vector Analyzer Signal 2 Vector Generator Signal 3 Shielding Room Model Serial Number Manufacturer FSQ40 200089 Rohde Schwarz & SMU200A 103752 Rohde Schwarz & S81 / ETS-Lindgren Calibration Period Calibration Due Date 1 year 2023-05-15 1 year 2023-05-15 / / ANNEX A: MEASUREMENT RESULTS A.1. Measurement Method A.1.1. Conducted Measurements Copyright. All rights reserved by CTTL. Page 8 of 15
No.I22Z61813-IOT06 The below figure shows the DFS setup, where the EUT is a RLAN device operating in slave mode, without Radar Interference Detection function. This setup also contains a device operating in master mode. The radar test signals are injected into the master device. The EUT (slave device) is associated with the master device. WLAN traffic is generated by streaming the mpeg file from the master to the slave in full monitor video mode using the media player. Note: 1) All Measurements are performed with the EUT’s narrowest channel bandwidth. 2) The master device information is as follows Vendor: RUCKUS Model: R600 FCC ID: S9GR600 3) The software of radar signal generator (R&S SMU200A) is completely designed based on KDB 905462 requirement. A.1.2. Parameters of DFS test signal 1). Interference threshold values, master or client incorporation in service monitoring. For device power less than 23dBm (E.I.R.P.), the threshold level is -62 dBm at the antenna port after correction for antenna gain and procedural adjustments. Because of conducted measurement performed, the calibration power from radar signal generator to antenna port of DFS test equipment is -62 dBm. Maximum Transmit Power Value 200 mW -64 dBm 200 mW -62 dBm The radar Detection Threshold, lowest antenna gain is the parameter of interference radar DFS detection threshold. One 10 Second plot bee reported for the short Pulse Radar type 1-4，the type 0 was be used, which was selected by auto test software. Radar Waveform Calibration Result: Copyright. All rights reserved by CTTL. Page 9 of 15
No.I22Z61813-IOT06 RBW 3 MHz VBW Ref -10 dBm * Att 5 dB 10 MHz SWT 1 s Marker 1 [T1 ] -61.79 dBm 201.923077 ms -10 A -20 SGL 1 AP CLRWR -30 -40 -50 1 -60 3DB -70 -80 -90 -100 -110 Center 5.61 GHz Date: 15.JAN.2022 100 ms/ 06:39:49 Fig.A.1 80M Calibration Result 2). DFS requirement values The required values are as the following table. Parameter Value Non-occupancy 1800 s Channel Availability Check Time 60 s Channel Move Time 10 s Channel Closing Transmission Time 200 ms 60 ms U-NII Detection Bandwidth Minimum 80% of the 99% transmission power bandwidth As the EUT is IP based system, the MPEG video file from NTIA website is used to steam to EUT via the Master device. A.1.3. Measurement Uncertainty Item Measurement Uncertainty Time 0.70 ms Power 0.75 dBm Copyright. All rights reserved by CTTL. Page 10 of 15
No.I22Z61813-IOT06 A.2. Channel move time and channel closing transmission time Measurement Limit: Test Items Limit channel closing transmission time 200 ms 60 ms Channel move time 10 s Measurement Results: Frequency Band: 5250MHz 5350MHz RBW 3 MHz VBW Ref -20 dBm Att 5 dB 10 MHz SWT 12 s Delta 2 [T1 ] -39.57 dB 10.000000 s Marker 1 [T1 ] -20 -32.45 dBm 326.923077 ms 1 -30 A SGL 1 AP CLRWR -40 -50 -60 2 -70 3DB -80 -90 -100 -110 -120 Center 5.29 GHz Date: 21.OCT.2022 1.2 s/ 16:37:41 Fig.A.2 Channel move time The channel move time is as the figure. It shows the time of the radar and the client pulses. The figure shows that the client stops transmission within 10 seconds, and no transmissions occur after 10 seconds later of the radar burst signal. Copyright. All rights reserved by CTTL. Page 11 of 15
No.I22Z61813-IOT06 RBW 3 MHz VBW Ref -20 dBm Att 5 dB Delta 4 [T1 ] 10 MHz SWT 3 s -39.07 dB 418.269231 ms Marker 1 [T1 ] -20 -32.52 dBm 350.961538 ms 1 -30 A SGL Delta 2 [T1 ] 1 AP -39.44 dB CLRWR 28.846154 ms -40 Delta 3 [T1 ] -39.82 dB -50 408.653846 ms -60 4 3 2 -70 3DB -80 -90 -100 -110 -120 Center 5.29 GHz Date: 21.OCT.2022 300 ms/ 16:16:58 Fig.A.3 channel closing transmission time The closing transmission time is as the figure, and the result is 76.95ms Delta2 (Delta4-Delta3)*5. Conclusion: PASS Frequency Band 5470MHz 5725MHz Ref -20 dBm Att 5 dB RBW 3 MHz VBW 10 MHz SWT 12 s Delta 2 [T1 ] -39.71 dB 10.000000 s Marker 1 [T1 ] -20 -32.27 dBm 1 519.230769 ms -30 A SGL 1 AP CLRWR -40 -50 -60 2 -70 3DB -80 -90 -100 -110 -120 Center 5.53 GHz Date: 26.OCT.2022 1.2 s/ 14:59:31 Fig.A.4 Channel move time The channel move time is as the figure. It shows the time of the radar and the client pulses. The figure Copyright. All rights reserved by CTTL. Page 12 of 15
No.I22Z61813-IOT06 shows that the client stops transmission within 10 seconds, and no transmissions occur after 10 seconds later of the radar burst signal. Ref -20 dBm Att 5 dB RBW 3 MHz VBW 10 MHz SWT 3 s Delta 4 [T1 ] -39.30 dB 341.346154 ms Marker 1 [T1 ] -20 -32.85 dBm -30 278.846154 ms 1 Delta 2 [T1 ] 1 AP CLRWR A SGL -39.55 dB 33.653846 ms -40 Delta 3 [T1 ] -38.32 dB -50 331.730769 ms -60 -70 3 4 2 3DB -80 -90 -100 -110 -120 Center 5.53 GHz Date: 26.OCT.2022 300 ms/ 14:53:12 Fig.A.5 channel closing transmission time The closing transmission time is as the figure, and the result is 62.51ms Delta2 (Delta4-Delta3)*3. Conclusion: PASS A.3.Non-Occupancy Period Measurement Limit: Test Items Non-Occupancy Period Limit 1800 s A3.1 Associated test Associate the master and client, transmit specified stream between the master and client; monitor the analyzer on the operating frequency to make sure no beacons have been transmitted for 1800 seconds. Frequency Band: 5250MHz 5350MHz Copyright. All rights reserved by CTTL. Page 13 of 15
No.I22Z61813-IOT06 RBW 3 MHz VBW Ref -20 dBm Att 5 dB Delta 2 [T1 ] 10 MHz -37.59 dB SWT 2000 s 1.800000 ks Marker 1 [T1 ] -20 -31.68 dBm 1 99.358974 s -30 A SGL 1 AP CLRWR -40 -50 -60 2 -70 3DB -80 -90 -100 -110 -120 Center 5.29 GHz Date: 22.OCT.2022 200 s/ 12:54:31 Fig.A.6 Non-Occupancy Period The figure above shows that the client does not transmit any emission within 1800 seconds after getting the order of “stop transmits” from the DFS master (access point). Frequency Band: 5470MHz 5725MHz Ref -20 dBm Att 5 dB RBW 3 MHz VBW 10 MHz -37.63 dB SWT 2000 s 1.800000 ks Delta 2 [T1 ] Marker 1 [T1 ] -20 -32.89 dBm 99.358974 s -301 A SGL 1 AP CLRWR -40 -50 -60 2 -70 3DB -80 -90 -100 -110 -120 Center 5.53 GHz Date: 26.OCT.2022 200 s/ 15:47:54 Fig.A.7 Non-Occupancy Period Copyright. All rights reserved by CTTL. Page 14 of 15
No.I22Z61813-IOT06 The figure above shows that the client does not transmit any emission within 1800 seconds after getting the order of “stop transmits” from the DFS master (access point). Conclusion: PASS ANNEX B: EUT parameters Disclaimer: The antenna gain provided by the client may affect the validity of the measurement results in this report, and the client shall bear the impact and consequences arising therefrom. ANNEX C: Accreditation Certificate *** END OF REPORT BODY *** Copyright. All rights reserved by CTTL. Page 15 of 15
TEST REPORT No.I22Z61813-IOT06 for Honor Device Co., Ltd. Smart Phone RMO-NX3 With FCC ID: 2AYGCRMO-NX3 Hardware Version: HN2RMOM Software Version: 6.1.0.21(C900E21R1P1) Issued Date: 2022-11-04 Note: The test results in this test report relate only to the devices specified in this report. This report shall not be reproduced
The magnetic moments of the fcc/fcc, hcp/hcp twin and fcc/hcp twin-like boundaries in cobalt were investigated by first-principles calculations based on density functional theory. The magnetic moments in fcc/fcc were larger than ofthose the bulkfcc, while the variations in the magnetic moment were complicated in hcp
E-rate Productivity Center Requesting services (FCC Form 470) Competitive bidding process Ordering services (FCC Form 471) Application review and funding commitments Begin receiving services (FCC Form 486) Invoicing USAC (FCC Form 472 and FCC Form 474)
eng i FCC and IC Compliance Statement PINPOINT KEY FOB, FCC ID ‑ MVU10148 ACMA: N2523 IC: 6094A‑09291, 6094A‑09305 This device complies with part 15 of the FCC Rules.
are layed out the same as the question pool from the FCC. We have attached a copy of the question pool to the end of this study guide, this pool of questions are the latest from the FCC, the date of the pool is 2009 FCC Commercial Element 1 (approved 25 June 2009). Most all of the information is from 47CFR-Part 80 and other Pub used is Pub 102.
FCC 601- Main Form Instructions August 2016- Page 1 FCC 601 FEDERAL COMMUNICATIONS COMMISSION Approved by OMB Main Form 3060 – 0798 Information and Instructions Est. Avg. Burden Per Response: 1.25 hours FCC Application for Radio Service Authorization:
- FCC: Be registered at FCC database and have a Grantee code. . A new application for equipment authorization shall be filled whenever there is a change in the FCC Identifier for the equipment with or without a change in design
the E-rate Productivity Center (EPC) for at least 28 days before the FCC Form 471 is filed, unless you are specifically exempted by FCC rules from the FCC Form 470 posting requirement. The 28-day waiting period begins after the FCC Form 470 is certi
6061-T6) extruded aluminum per ASTM B221-08. The rails are used in pairs to support photovoltaic solar panels in order to span between points of attachment to the existing roof structure. The following tables and information summarize the structural analysis performed by SEI in order to certify the SMR100 Rail for the state noted above.
